OWNER’S RECORD
d
For your convenience, record the model number and the serial number (you will
find it on the bottom of your set) in the space provided below. Please refer to
them when you contact your Aiwa dealer in case of difficulty.
c
Model No.
Serial No.
XP-R210
COMPACT DISC PLAYER
NOTE
FOR USE IN THE U.S.A.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation.
OPERATING INSTRUCTIONS
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Modifications or adjustments to this product, which are not expressly approved
by the manufacturer, may void the user’s right or authority to operate this product.
Highlighted letters in the text of this manual correspond to the illustrations.
PRECAUTIONS
To maintain good performance
• Do not use the unit in places which are extremely hot, cold, dusty or humid. In
particular, do not use or keep the unit in following places.
• in a high humidity area such as a bathroom
8A-HC1-901-11
000316BMN-O9
Printed in Indonesia
• near a heater
• in an area exposed to direct sunlight (e.g., inside a parked car, where it can
become extremely hot)
• near sources of strong magnetism, such as televisions, speakers, or magnets
• where there is a lot of movement or vibration, such as on a car dashboard or
an unstable shelf
A
For safety
• Do not attempt to disassemble the unit. Laser rays from the optical pickup are
dangerous to the eyes.
• Make sure that pins or other foreign object do not get inside the player.
• Take care not to drop the unit or subject it to strong shocks.
• To keep dust from the pickup lens, keep the disc compartment lid closed after
use. Never touch the lens.
A
• If you hear no sound when playing a disc, DO NOT turn the volume up high
because music could suddenly start at high volume. Turn the volume control
to the lowest level before starting playback and slowly turn it up to the desired
level.
AA (LR6) × 2
Note on listening with the headphones
• Listen at moderate volumes to avoid hearing damage.
• Do not wear the headphones while driving or cycling. It may create a traffic
hazard.
• You should use extreme caution or temporarily discontinue use in potentially
hazardous situations, such as walking, jogging, etc.
• Wear them properly; L is left, R is right.
B
Note on condensation
If the unit is suddenly moved from a cold place to a warm one, it may result in
condensation on the pickup lens and malfunction or playback difficulties.
Should this occur, leave the unit for a few hours, then try to playback again.
USING ON DRY CELL BATTERIES → A
Open the battery compartment and insert two size AA (LR6) alkaline batteries
with the 0 and 9 marks correctly aligned.
Battery replacement
OPE/BATT indicator changes from F (green) to M (orange) to E (red) according
to the remaining power of the batteries. Replace the batteries when E (red) lights.
If the unit remains in use after E (red) lights, “Lo-bAtt” appears and operation
stops.
Battery life (using alkaline batteries LR6)
The setting of the E•A•S•S switch
Battery life
48
12
OFF
Approx. 20 hours
Approx. 19 hours
Approx. 15 hours
Battery life may vary depending on conditions of use.
B
USING ON RECHARGEABLE BATTERIES → C
• Be sure to use sizeAA Ni-Cd 1.2 V 700 mAh rechargeable batteries, which are
commercially available.
• Be sure to read the instructions of the purchased rechargeable batteries before
use.
• When using on rechargeable batteries for the first time, charge them until the
battery indicator goes out.
• Before charging the batteries, close the disc compartment. You cannot charge
the batteries while it is opened.
1
2
C
3
1 Insert the rechargeable batteries with the 0 and 9 marks correctly
aligned.
2 Connect the AC adaptor.
1 to DC 5 ~ 6 V jack
2 to a wall outlet
3 Keep sSTOP/OFF/CHARGE pressed for about 1 second to start charging.
“C-On” appears, and OPE/BATT indicator blinks.
When charging is completed, “C-OFF” flashes a few times, and OPE/BATT
indicator goes out.
After charging, disconnect the AC adaptor.
Time to recharge the batteries
Recharge the batteries when E (red) lights. If the unit remains in use after E
(red) lights, “Lo-bAtt” appears and the current operation stops.
To stop charging
Press a STOP/OFF/CHARGE during charging.
ATTENTION:
The product you have purchased can be powered by
nickel cadmium batteries which is recyclable. At the
end of their useful life, under various state and local
laws, it is illegal to dispose of these batteries into your
municipal waste stream.
D
Please call 1-800-289-2492 for information on how to
recycle these batteries.
USING ON AC HOUSE CURRENT
Connect the supplied AC adaptor in the same way as when recharging the
batteries.
During operation on AC house current, all of OPE/BATT indicators light.
BEFORE PLAYBACK
E
HOLD switch → D
Release the HOLD switch before playback. → a
When not using the unit, set the HOLD switch to the HOLD position. → b
Accidentally pressed button will not function.
If buttons are pressed when the HOLD switch is set to the HOLD position, “HOLd”
flashes in the display.
Turning on and off → D
Turning the power on
Press e PLAY/PAUSE. Power is turned on and playback starts.
Note
“Err” appears on the display when you play a disc placed upside-down or a
defective disc.
Turning the power off
1
F
If no new operations are done within 30 seconds from the end of last operation,
the power is turned off automatically. (Auto power off function)
• You can turn off the power by pressing sSTOP/OFF/CHARGE before it is
automatically turned off.
Standby mode → D
When an operation finishes, the unit goes into standby mode until the auto power
off function automatically turns off the power.
To enter standby mode, press e PLAY/PAUSE to start playback, then press
sSTOP/OFF/CHARGE.
Adjusting the sound → E
2
3
Volume
Turn the VOL control to adjust the volume.
DSL
Press DSL repeatedly for more powerful sound and deeper bass.
: Deep bass is emphasized.
: Deep bass is strongly emphasized.
: Normal sound
Signal sound function
You can check the operation by beep sound when you press an operation button.
The signal sound function is not activated when you purchase this unit.
To use the signal sound function, press ePLAY/PAUSE while pressing PLAY
MODE while in stop mode. The beep sound is heard when you press a button.
G
BEFORE PLAYBACK
HOLD switch → D
Release the HOLD switch before playback. → a
When not using the unit, set the HOLD switch to the HOLD position. → b
Accidentally pressed button will not function.
If buttons are pressed when the HOLD switch is set to the HOLD position, “HOLd”
flashes in the display.
Turning on and off → D
Turning the power on
Press e PLAY/PAUSE. Power is turned on and playback starts.
Note
“Err” appears on the display when you play a disc placed upside-down or a
defective disc.
Turning the power off
1
F
If no new operations are done within 30 seconds from the end of last operation,
the power is turned off automatically. (Auto power off function)
• You can turn off the power by pressing sSTOP/OFF/CHARGE before it is
automatically turned off.
Standby mode → D
When an operation finishes, the unit goes into standby mode until the auto power
off function automatically turns off the power.
To enter standby mode, press e PLAY/PAUSE to start playback, then press
sSTOP/OFF/CHARGE.
Adjusting the sound → E
2
3
Volume
Turn the VOL control to adjust the volume.
DSL
Press DSL repeatedly for more powerful sound and deeper bass.
: Deep bass is emphasized.
: Deep bass is strongly emphasized.
: Normal sound
Signal sound function
You can check the operation by beep sound when you press an operation button.
The signal sound function is not activated when you purchase this unit.
To use the signal sound function, press ePLAY/PAUSE while pressing PLAY
MODE while in stop mode. The beep sound is heard when you press a button.
To cancel the beep sound, repeat this procedure.
G
Inserting a disc → F
1 Slide the OPEN switch to open the disc compartment.
2 Place a disc in the center with the label side facing up.
3 Close the disc compartment.
To remove the disc → G
Pick up the disc, holding its edge, while pressing the pivot gently.
Note
• The unit may not play a CD-R/RW disc that is recorded on personal computers
or some kinds of CD-R/RW recorders because of differences in recording
platforms.
• Do not attach any seal or label to either side (the recordable side or the labeled
side) of a CD-R/RW disc. It may cause malfunction.
PLAYBACK → H
H
Connect the supplied headphones to the PHONES/LINE OUT jack.
1 Release HOLD.
2 Place a disc.
3 Press PLAY/PAUSE.
Playback starts from the first track.
a track number
b elapsed playing time
Basic operation
To stop
Press sSTOP/OFF/CHARGE.
To pause
Press e PLAY/PAUSE.
To resume, press it again.
To search for the beginning of a track
To locate a desired passage
Press ror t.
1
2
Keep r or t pressed.
Release the button at the start of desired
passage.
Display during playback → I
Press ENTER/DISP during playback to change the display as follows.
1 Track display and elapsed playing time (normal display)
V
2 Track display and remaining playing time of the track in play
V
3 Remaining number of tracks and remaining playing time
3
The time is not displayed in following cases.
• When trying to program tracks beyond No.32.
• When the total remaining time of the programmed tracks is over 100 minutes.
E•A•S•S PLUS (Electronic Anti-Shock System) → J
The E•A•S•S PLUS function reduces skipping or muting of the sound when the
unit is subjected to shocks.
The player keeps about 48 seconds or 12 seconds of playback sound in its
memory.
I
To keep 48 seconds in the memory, set the E•A•S•S switch to 48.
To keep 12 seconds in the memory, set the E•A•S•S switch to 12.
To cancel the E•A•S•S PLUS function, set the E•A•S•S switch to OFF.
ENTER/DISP
Note
• Before jogging with this unit, allow sufficient time for the memory buffer to fill up
completely (ideally 40 to 48 seconds).
Continuous shock or vibration may cause the sound to be interrupted even if
the E•A•S•S PLUS function is activated. This is normal and not a malfunction.
Should you experience an interruption in sound, stabilize the unit for a few
seconds, then resume your activity.
• When the E•A•S•S switch is slid during playback, the unit will pause for about
2 seconds.
• When you set the E•A•S•S switch to the 12 or OFF position, the quality of the
sound will be better than the case that you set it to the 48 position.
V
V
Resume function → K
Set the HOLD switch to RESUME.
appears, and you can start playback from the point where you stopped
playback by pressing sSTOP/OFF/CHARGE.
When the resume function is on, all-track repeat is selected automatically.
To cancel resume play, set the HOLD switch to OFF.
J
K
Note
• Resume play may start at a point about 30 seconds behind or ahead the stopped
point. Resume play may not operate if you stopped at the last 30 seconds of
the final track.
• Resume play will be canceled if you open the disc compartment. If the unit is
turned off, resume play will not be canceled. In this case, be sure to set the
HOLD switch to OFF before changing discs.
Random play → K
Press PLAY MODE while in standby mode to display
.
Tracks on the disc are played in random order.
V
V
To cancel random play, press PLAY MODE while in standby mode.
display changes to
.
Note
• You cannot back to previous track by pressing r during random play.
• You cannot select one-track repeat during random play.
Repeat play → K
Press PLAY MODE during playback to select repeat play as follows.
: one-track repeat
B
V
: all-track repeat
V
no repeat play (normal play)
Continuous shock or vibration may cause the sound to be interrupted even if
the E•A•S•S PLUS function is activated. This is normal and not a malfunction.
Should you experience an interruption in sound, stabilize the unit for a few
seconds, then resume your activity.
• When the E•A•S•S switch is slid during playback, the unit will pause for about
2 seconds.
• When you set the E•A•S•S switch to the 12 or OFF position, the quality of the
sound will be better than the case that you set it to the 48 position.
V
V
Resume function → K
Set the HOLD switch to RESUME.
appears, and you can start playback from the point where you stopped
playback by pressing sSTOP/OFF/CHARGE.
When the resume function is on, all-track repeat is selected automatically.
To cancel resume play, set the HOLD switch to OFF.
J
Note
• Resume play may start at a point about 30 seconds behind or ahead the stopped
point. Resume play may not operate if you stopped at the last 30 seconds of
the final track.
• Resume play will be canceled if you open the disc compartment. If the unit is
turned off, resume play will not be canceled. In this case, be sure to set the
HOLD switch to OFF before changing discs.
Random play → K
Press PLAY MODE while in standby mode to display
.
Tracks on the disc are played in random order.
V
V
To cancel random play, press PLAY MODE while in standby mode.
display changes to
.
Note
• You cannot back to previous track by pressing r during random play.
• You cannot select one-track repeat during random play.
Repeat play → K
Press PLAY MODE during playback to select repeat play as follows.
: one-track repeat
B
K
L
V
: all-track repeat
V
no repeat play (normal play)
PROGRAM PLAY → L
Up to 24 tracks can be chosen for program play.
1 Press ENTER/DISP while in standby mode to display
2 Select the desired track by pressing r and t.
a track number
b program number
3 Press ENTER/DISP within 8 seconds.
.
If it is not pressed within 8 seconds, the track number changes to 00. Repeat
the procedure from step 2 again.
4 Repeat steps 2 and 3 to program more tracks.
5 Press e PLAY/PAUSE to start program play.
To stop program play
Press sSTOP/OFF/CHARGE.
To add tracks to the program
Repeat steps 2 and 3 before you proceed to step 5. You can add tracks to the
end of the program.
ENTER/DISP
1
2
3
5
To erase the program
Press sSTOP/OFF/CHARGE while in standby mode.
To check the programmed tracks
Press ENTER/DISP repeatedly before you proceed to step 5.
The number of each programmed track will be displayed in order of playback.
Note
• The program is also erased when the disc compartment is opened or the auto
power off function turns the power off.
• When 24 tracks are programmed, “P-FULL” appears, and no more tracks may
be added.
• You cannot back to the previous track by holding r pressed during program
play.
ENTER/DISP
• Repeat play and random play can be performed during program play.
RADIO RECEPTION
M
Tuning in to a station → M
1 Press TUNER ON/BAND repeatedly to select AM or FM.
2 Press TUNING + (t) or - (r) to tune in to a station.
After listening, press sSTOP/OFF/CHARGE to turn off the radio.
For quick tuning
Keep either TUNING + (t) or - (r) pressed for about 1 second. When a
station is tuned in to, the frequency stops automatically. However, it does not
stop if the broadcast signal is weak.
For better reception → N
1
2
FM: The headphone cord functions as the FM antenna. Keep it extended.
AM: Turn the unit to find the position which gives the best reception.
To listen to an FM stereo broadcasting
When a tuned in station is in stereo, ST changes to
When the FM stereo signal is weak and distorted, press MONO/ST. ST goes out
and the sound will be heard in monaural but distortion will be reduced.
.
Note
• Do not open the disc compartment during radio reception. The buttons will be
deactivated.
• The power is turned off automatically if no operation is made after 180 minutes
from the last operation during radio reception.
FM
AM
AM steps → O
N
O
Radio broadcasts have different frequency ranges and changes in different steps
in different countries.
This unit is factory-set to 10 kHz steps on AM. When using the unit where theAM
step changes to 9 kHz, set the AM STEP switch on the inner side of the disc
compartment to 9 kHz.
• When the AM step is changed, stations that you preset are erased.
Presetting stations → P
You can preset up to total of 30 stations on AM and FM.
1 Press TUNER ON/BAND repeatedly to select AM or FM.
2 Press TUNING + (t) or - (r) to tune in to a station.
3 Press ENTER/DISP to preset the station.
a Preset number
AM STEP
9kHz
10kHz
To preset more stations, repeat steps 2 and 3.
Listening to preset stations → Q
1 Press TUNER ON/BAND repeatedly to select AM or FM.
2 Press PRESET CALL
i/k
repeatedly to select the preset number.
After listening, press sSTOP/OFF/CHARGE to turn off the radio.
Changing the presetting
P
1 Press PRESET CALL
wish to change.
i/
k
repeatedly to select the preset number you
2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number
and the frequency flash.
3 While the preset number is flashing, press TUNING + (t) or - (r)
to tune in to a station.
4 Press ENTER/DISP to preset the station on the selected preset number.
If the flashing stops, repeat the procedure from step 2.
Erasing the presettings one by one
Press sSTOP/OFF/CHARGE after step 2 in “Changing the presetting” above.
Each preset station is erased. All the settings move up by one and the preset
numbers are refreshed.
1
2
3
Erasing all of the presetting
Keep ENTER/DISP pressed, then press TUNER ON/BAND when the frequency
and preset number starts flashing.
CONNECTING TO AN EXTERNAL UNIT → R
Use a commercially available connection cord which has a 3.5 ø stereo mini-
plug at one end and two phono plugs at the other end.
Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and
connect the phono plugs to the analog input terminals of the external unit.
ENTER/DISP
Note
• Turn off the power of both units before connection.
• DO NOT connect to the PHONO inputs of an amplifier (with a built-in
phonoequalizer-amplifier).
• Adjust the volume and DSL on this unit.
Q
MAINTENANCE
To clean the lens → S
If the lens becomes dirty, the player will skip or not play. If this occurs, clean the
lens in the following manner.
To remove dust or dry particles, first use a camera lens blower/brush a to blow
a few times to loosen particles, then gently brush the lens b clean. Finish by
blowing the lens again.
2 Press PRESET CALL
i/k
repeatedly to select the preset number.
After listening, press sSTOP/OFF/CHARGE to turn off the radio.
Changing the presetting
P
1 Press PRESET CALL
wish to change.
i/
k
repeatedly to select the preset number you
2 Keep ENTER/DISP pressed for 1 or more seconds until the preset number
and the frequency flash.
3 While the preset number is flashing, press TUNING + (t) or - (r)
to tune in to a station.
4 Press ENTER/DISP to preset the station on the selected preset number.
If the flashing stops, repeat the procedure from step 2.
Erasing the presettings one by one
Press sSTOP/OFF/CHARGE after step 2 in “Changing the presetting” above.
Each preset station is erased. All the settings move up by one and the preset
numbers are refreshed.
1
2
3
Erasing all of the presetting
Keep ENTER/DISP pressed, then press TUNER ON/BAND when the frequency
and preset number starts flashing.
CONNECTING TO AN EXTERNAL UNIT → R
Use a commercially available connection cord which has a 3.5 ø stereo mini-
plug at one end and two phono plugs at the other end.
Connect the stereo mini-plug to the PHONES/LINE OUT jack of the unit and
connect the phono plugs to the analog input terminals of the external unit.
ENTER/DISP
Note
• Turn off the power of both units before connection.
• DO NOT connect to the PHONO inputs of an amplifier (with a built-in
phonoequalizer-amplifier).
• Adjust the volume and DSL on this unit.
Q
R
MAINTENANCE
To clean the lens → S
If the lens becomes dirty, the player will skip or not play. If this occurs, clean the
lens in the following manner.
To remove dust or dry particles, first use a camera lens blower/brush a to blow
a few times to loosen particles, then gently brush the lens b clean. Finish by
blowing the lens again.
To remove fingerprints, use a cotton swab dipped in lens cleaning solution. Wipe
gently from the center to the edge. Lens cleaning solution is commercially
available.
Note
Take care not to get too much solution on the swab, which could flow into the unit
and cause damage.
Pressing too strongly with the swab could scratch or break the lens.
To clean the discs → T
Before playing, wipe the disc from the center outward with a cleaning cloth. After
playing, store the disc in its case.
SPECIFICATIONS
Tracking system
Laser pickup
D/A conversion
Frequency response
Output
3-beam laser
Semiconductor laser
4-times oversampling digital filter + 1-bit DAC
20 – 20,000 Hz (47 k ohms)
PHONES/LINE OUT jack (stereo mini-jack)
AM: 530/531 kHz – 1,710/1,602 kHz
(10 kHz/9 kHz steps)
S
T
Frequency range
FM: 87.5 – 108 MHz
Maximum output
Power supply
12 mW + 12 mW (16 ohms at 1 kHz)
500 mV (47 k ohms at 1 kHz)
DC 3 V using two size AA (LR6) alkaline
batteries
DC 2.4 V using two commercially available
(Ni-Cd 1.2 V 700 mAh) rechargeable batteries
AC house current using the supplied AC adaptor
Maximum outside dimensions
128 (W) × 31.2 (H) × 129.5 (D) mm (excluding
projecting parts and controls)
(5 1/8 × 1 1/4 × 5 1/8 in.)
Weight
Accessories
Approx. 225 g (7.9 oz.) excluding batteries
AC adaptor AC-D603 (1)
Stereo headphones (1)
Rated input: AC 120 V, 60 Hz
AC adaptor AC-D603U
The specifications and external appearance of this unit are subject to change
without notice.
|