USB Ethernet Adapter
Quick Installation Guide
Quick Installation Guide
Installation
Warning: Please view the README.TXT file on the Ethernet Adapter
driver diskette for product related information.
Install the driver as described below:
Windows 95
1. Connect the Type-A plug into the USB port on the computer.
2. Insert the Driver Software Diskette.
3. Double-click on My Computer.
4. Double-click on 3-1/2 Floppy (A:).
5. Double-click on Win95/Setup.exe.
6. When prompted, connect the Type-B plug into the adapter.
7. You will observe several loading status windows.
8. If prompted to insert the Windows 95 CD-ROM, do so and
click OK.
9. When prompted to restart the computer, remove the
diskette and click Yes.
Windows 98
1. Connect the Type-A plug into the USB port on the computer.
2. Connect the Type-B plug into the adapter.
3. Connect the adapter to the Ethernet network.
4. The New Hardware Wizard displays.
5. When prompted for the installation medium, check Floppy
Disk Drive and insert the Driver Software Diskette.
6. Follow displayed instructions.
7. You will observe several loading status windows.
8. When prompted to restart the computer, remove the
diskette and click Yes.
When the installation process is complete, remove the diskette
from your drive and follow the instructions for restarting your
PC. After rebooting your system, the USB Ethernet Adapter
will appear to the system as a normal Ethernet network
adapter card. For the LED definitions, see "LED functions"
below.
Note: If the Wizard does not appear when you plug in the Ethernet
Adapter, please view the section "Is USB correctly installed" in the
README.TXT file on the Ethernet Adapter driver diskette.
Power Requirements
USB devices can be either self-powered or bus-powered. A
device which has no power connector is bus-powered, and
derives its operating power from the USB connection directly.
The Ethernet Adapter is bus-powered – all you need to do is
plug it into a PC or USB hub (such as Accton’s USB204A).
3
USB Ethernet Adapter
LED Functions
The Ethernet Adapter contains two LED's on the side panel of
the RJ-45 connector. The left Green LED is LINK and the right
Orange LED is Receive/Transmit activity. The operational status
of the adapter is indicated by the LED conditions listed below.
Link
Activity
Indication
ON
ON
Power ON - LED's light initially for 3 seconds.
Adapter is connected to the computer but not configured.
Normal operation, no network activity.
Flashing
ON
Flashing
OFF
ON
ON
Normal operation, network activity.
OFF
OFF
OFF
ON
No network connection to the RJ-45 socket.
Failed self-diagnostics at start-up.
Always
Always
Ethernet configuration problem. Check all cabling.
Flashing
Flashing
USB Application Diagram
4
Quick Installation Guide
EMIWarning
FCC Class B Certification
Accton Technology Corporation
Model Numbers: USB220-EC
FCC ID: HED1045USB
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
Warning: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
· Reorient or relocate the receiving antenna
· Increase the separation between the equipment and receiver
· Connect the equipment into an outlet on a circuit different
from the one which the receiver is connected to
· Consult the dealer or an experienced radio/TV technician for help
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void
your authority to operate the equipment.
Attach unshielded or shielded Category 3, 4 or 5 twisted-pair
cable to the RJ-45 port, and shielded USB cable to the USB port.
Note: In order to maintain compliance with the limits of a Class
B digital device, Accton requires that you use a quality
interface cable when connecting to this device. Changes or
modifications not expressly approved by Accton could void the
user's authority to operate this equipment. Suggested cable
type is 90Ω USB cable for the USB port, and 100Ω shielded or
unshielded Cat. 3, 4 or 5 twisted-pair cable.
Canadian Standards Association (CSA) Statement
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
radio interference regulations of the Canadian Department of
Communciations.
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de
Classe B prescrites dans la norme sur le matériel brouilleur:
"Appareils Numérques", NMB-003 édictée par le ministère des
Communications.
5
USB Ethernet Adapter
VCCI Class B Compliance (Japan)
EN55022 Declaration of Conformance
This is to certify that the Accton USB220-SC is shielded against
the generation of radio interference in accordance with the
application of Council Directive 89/336/EEC, Article 4a.
Conformity is declared by the application of EN55022:1987
Class B (CISPR 22:1985/BS 6527:1988).
CE Mark Declaration of Conformance
This is to certify that this product complies with ISO/IEC Guide
22 and EN45014. It conforms to the following specifications:
EMC:
EN55022(1988)/CISPR-22(1985)
IEC 1000-4-2(1995)
class B
4kV CD, 8kV AD
IEC 1000-4-3(1995)
3V/m
IEC 1000-4-4(1995)
1kV - (power line)
IEC 1000-4-6(1995)
3Vrms
This product complies with the requirements of the Low Voltage
Directive 73/23/EEC and the EMC Directive 89/336/EEC.
6
Quick Installation Guide
Product Specifications
Standards Conformance
System Requirements
USB Specification 1.0 (for USB low-power device)
A PC that supports the Universal Serial Bus (Windows 98)
Also requires device driver (included)
Ports
1USBB-Typereceptaclefordownstream(device)connections
RJ-45 Ethernet port for 10BASE-T, 10Mbps connections
USBport:90ŠshieldedUSBcable, 5m(16ft)max. length
Ethernet port: 100ŠCategory 3,4,5 shielded/unshielded
twisted-pair with max length of 100 m (328 ft)
12 Mbps full speed on USB side, and up to 8 Mbps on
Ethernet side
Cable Wiring
Access Method
Dimensions
Weight
25.3 x 55.4 x 67.8 mm (1.0 x 2.18 x 2.67 in)
50 g (1.76 oz)
Input Power
4.25~5.25 VDC, 0.5A max.
(bus powered from USB host controller or hub)
2.65 Watts maximum (from USB host)
9.04 BTU/hr
Power Consumption
Heat Dissipation
Environmental
Temperature
0°C - 40°C / 32°F -104°F (Standard Operating)
-20°C - 70°C / -4°F - 160°F (Storage)
5- 95% (Noncondensing)
Humidity
Certification
CE Mark
EN50081-1, EN55022 Class B
EN50082-1, IEC 1000-4-2/3/4/6
Emissions
FCC Class B, VCCI Class B, CISPR Class B
7
USB Ethernet Adapter
Warranty
Accton warrants to the original owner that the product delivered in this
package will be free from defects in material and workmanship for the
lifetime of the product. For the warranty to apply, you must register your
purchase by returning the registration card indicating the date of purchase
and including proof of purchase. There will be a minimal charge to
replace consumable components, such as fuses, power transformers,
and mechanical cooling devices. The warranty does not cover the
product if it is damaged in the process of being installed. Accton
recommends that you have the company from whom you purchased
this product install it.
THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY,
WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING BUT
NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, OR ANY WARRANTY ARISING OUT
OF ANY PROPOSAL, SPECIFICATION OR SAMPLE. ACCTON SHALL
NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
ACCTON NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY.
Copyright
Copyright © 1999 by Accton Technology Corporation. All rights reserved.
No part of this document may be copied or reproduced in any form or
by any means without the prior written consent of Accton Technology
Corporation.
Accton makes no warranties with respect to this documentation and
disclaims any implied warranties of merchantability, quality, or fitness
for any particular purpose. The information in this document is subject
to change without notice. Accton reserves the right to make revisions
to this publication without obligation to notify any person or entity of
any such changes.
International Headquarters
No. 1 Creation Road III,
USA Headquarters
P.O. Box 51420
Science-based Industrial Park
Hsinchu 300, Taiwan, R.O.C.
Phone: 886-3-5770-270
Irvine, CA 92619-1420
Phone Numbers -
Sales: 888-398-2101, 949-707-4800
Support: 888-398-4101, 949-707-4847
FAX: 886-3-5770-267
Internet: [email protected]
RMA:
888-398-3101, 949-707-4828
FAX: 949-707-2460
Accton is a trademark of Accton Technology Corporation. Other
trademarks or brand names mentioned herein are trademarks or
registered trademarks of their respective companies.
USB220-EC
E0299-R01
150007-102
|