Primus 160
Infinity Loudspeaker Troubleshooting/Repair Tips
Most customers prefer to do simple loudspeaker repairs themselves. By following the steps below, a majority of loudspeakers can be returned to
their original factory performance with minimum effort. Choose the example that best describes the problem you are experiencing.
Problem 1: No sound or distorted sound from one loudspeaker in a pair (or set)
Connect the dead/distorting loudspeaker to a different amplifier channel (one that had a functioning loudspeaker connected to it). If it functions
normally, the problem is not loudspeaker-related. If the loudspeaker still makes no sound or sounds distorted, a wire may have become loose
or disconnected, the network (also known as a crossover) may be defective, the drivers (woofer, tweeter, etc.) may be defective or, in very rare
cases, all may be defective.
Refer to the wiring diagram and exploded view below. The network is a small circuit board found on the inside of the terminal cup, or mounted to
an inside wall of the enclosure. It sends low-frequency sounds to the woofer, high-frequency sounds to the tweeter and, if applicable, mid-frequency
sounds to the midrange driver. Make sure all wires are secure and connected. Look for components on the network that look burnt, “bulged,”
or abnormal. If everything looks normal, connect the network to the drivers from another matching loudspeaker. MAKE SURE you attach the
correct wires to each driver – mid- and low-frequency sounds can damage the tweeter! If there is still no sound or distorted sound, the network
is defective. If there is clean undistorted sound, the drivers are defective.
Problem 2: No sound or distorted sound from one or more (but not all) drivers in an enclosure
Remove the problem driver(s) from the enclosure and make sure all wires are secure and connected. If they are, proceed with the following test:
Woofer or midrange driver – Connect the driver’s + and – input terminals directly to the loudspeaker wires from your receiver/amplifier and play
some music at a reasonable volume. If the driver now sounds normal (produces a clean, undistorted sound), the network is most likely defective.
Tweeter – Replace the tweeter with a functioning tweeter from another loudspeaker. If the tweeter now functions normally (produces clean,
undistorted sound), the original tweeter is defective. If the replacement tweeter also sounds distorted or produces no sound, the network is
most likely defective.
Problem 3: Loudspeakers distort, rattle or pop at higher volumes
This is usually NOT a loudspeaker problem. Common causes are too much power (playing the loudspeakers too loud and causing them to distort),
an amplifier with not enough power (the amplifier can’t produce the required volume without distorting), excessive equalization (turning the tone
controls too far clockwise, and/or engaging the loudness/bass boost button on your receiver) or some combination of the above. If only one
loudspeaker is exhibiting the problem, and you’re confident that it’s not caused by too little power/too much power/excessive equalization, see
solutions for Problems 1 and 2.
WIRING DIAGRAM
EXPLODED VIEW
HIGH-FREQUENCY
TRANSDUCER
+
85DA20AJ-DT02
12
1
–
WHT
2
GRN
9
+RED
–BLK
3
10
LOW-FREQUENCY
TRANSDUCER
13
16PR90BZQ-FW01
CROSSOVER
NETWORK
013-7500-00754
11
8
7
4
6
Primus 160 Cabinet – Not for Sale
5
ITEM
ITEM
NO. DESCRIPTION
QTY.
PART NO.
013-7500-00754
NO. DESCRIPTION
QTY.
PART NO.
1.Crossover Network
2.Woofer
1
10.Faceplate/Tweeter FE Screw T4.5*25
11.Terminal Cup Screw 3.5*L20 d=6mm
12.Network Screw t4*18
13.Grille Cup
8
4
3
4
1
1
1
2
352-DM04525D597
352-GM03520D850
352-HM04018D497
338-RUB-00114
373-000-00124
1
1
1
1
1
1
1
16PR90BZQ-FW01
85DA20AJ-DT02
213-060-00492
3.Tweeter
4.ABS Plastic Trim Ring 196.5*144*8T
5.Grille 337*204*3T Black
244-060-00259B
249-HIPS-00161
316-ABS-00532-2
317-ABS-00165
14.Rubber Footbase (set of 4)
15.Outer Carton
6.Port Tube 49.6*48.8
400-000-04520
7.ABS Infinity Gold Logo 38.5*11.5
8.Network Cup W/Binding Posts
80*80mm ABS Gold Plating
9.Woofer Screw 4*L16 d=7mm
16.Owner’s Manual
406-000-01532
17.Polyfoam for Primus 160
440*350*80mm
431-000-02175
4
352-AM04016D834
18.Warranty Card
1
405-000-00312
Note: A Phillips screwdriver and "Torx" bit screwdriver T20 size are required to service this product
|