Operation Manual
NIGHT VISION WEAPON SCOPE
NVS 4
105 Sparks Ave., Toronto, ON, M2H 2S5, Canada
Table of contents
1.
OVERVIEW....................................................1
DELIVERY SET.............................................3
SPECIFICATIONS .........................................4
DESIGN ..........................................................5
OPERATION INSTRUCTIONS.....................7
MAINTENANCE..........................................10
STORAGE ....................................................11
TROUBLESHOOTING ................................12
WARRANTY................................................14
CUSTOMER SUPPORT...............................15
ACCEPTANCE CERTIFICATE ..................16
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
1. OVERVIEW
The night vision NVS 4 is aiming optical-electronic
weapon scope, intended for shooting gun with the side
mount at night time or dark conditions. The unit
utilizes a generation 2+ or better image intensifier tube,
which amplifies available moonlight, starlight or man-
made light. The device was designed to be easy to use,
and provide many years of operation.
Some of the typical activities where NVS 4 will be
useful:
•
•
•
Military
Law enforcement
Security
Features
•
Suitable for a variety of infantry AK 47 variants and
machine guns.
•
•
•
•
Supplied with East Block side mount or a custom mount
Precise internal Windage/Elevation adjustments
Lit ballistic reticle with adjustable brightness intensity
Automatic brightness protection
1
Precautions
NVS 4 is a sophisticated precise optical instrument
equipped with electronics.
Therefore, it should be handled with due care.
•
Keep your device away from direct sunlight,
impacts, dust, moisture,
and sudden changes of temperatures.
•
•
•
Do not touch the optical surfaces with fingers.
Doing so may damage the anti-reflection coating.
Cleaning of optical surfaces is allowed only with
professional camera lens cleaning supplies.
Use only a soft clean cloth to clean the exterior of
the device.
•
•
Do not take the cover off the lens if not necessary.
Keep away from heating appliances and central
heating.
•
Make sure to switch off the unit and remove the
batteries during periods of non-operation and when
storing the device for long period of time.
•
Do not apply superfluous efforts at work with lens
assembly, agile elements and thread connections.
Due to considerable optical magnification of the eye-piece
some
small structures inside the tube coating in the form of dark
and/or white points may be seen in the field of view which
does not affect
the serviceability of the device
2
2. DELIVERY SET
NVS 4 is supplied with the following components:
Quantity
NVS 4 unit
Wrench
1
1
1
1
1
1
Soft case
Napkin
Manual
Warranty registration card
*Exact delivery set and accessories included are
subject to the terms of specific contract.
3
3. SPECIFICATIONS
NVS4
NVS4/5x
Typical
starlight, m
range
at
350
2+
4
500
2+
5
Image Intensifier tube
Magnification, x
Field of view under
eye relief 40 mm, deg
6.3
6
6
6
Exit pupil diameter,
mm
Mount
East European
East European
Battery
АА, 1pc
АА, 1pc
Supply voltage, V
1,5
1,5
Continuous operation
time under standard
conditions, h
10 -30, depends on
battery type
10-30, depends on
battery type
Overall dimensions
Weight, kg
207х176х79
220х198х100
0.9
1.25
AK47, AK74,
AK74M, AK101,
AK102, AK105,
AK107, AK108,
AN94, AS, BSS.
PKM, SVD
AK47, AK74,
AK74M, AK101,
AK102, AK105,
AK107, AK108,
AN94, AS, BSS.
List of recommended
weapons
4
4. DESIGN
Figure 1.
2 – Lens
3 – Fitting part
4 – Scope housing
6 – Eye-shield
9 – Lead
11 – Washer
13 - Latch
5 – Clip
8 – Battery compartment cover
10 – Scope housing cover
12 – Stop screw
14 – Lock lever
15 – Handle
16 – Bracket
17 – Reticle brightness adjustment hand wheel
5
Figure 2.
1 – Lens cup with
brightness filter
7 – Switch
18 – Vertical adjustment
screw
19 – Cover of blow-out fitting
20 – Rubber gasket
21 – Horizontal adjustment screw
6
5. OPERATION INSTRUCTIONS
The scope is mounted on a weapon by means of clamp, which
consists of bracket 16 (Fig.1, 2), lock screw 2, latch 13, lock
lever 14, handle 15 and washer 11.
Mount the scope on a weapon in the following order:
-
-
pull the handle 15;
direct the scope from the rear side into aligning bar of a
weapon and push the scope forward to stop;
push the handle 15 up to its catching;
check up the reliability of scope fastening
-
-
A swinging of the scope on a weapon is not affordable.
For reliable fastening of the scope, it is necessary to adjust the
clamp in the following order:
-
-
-
-
-
detach the scope from the weapon;
unlock the latch 13;
shift the handle 15 providing the reliable fastening;
lock the latch 13;
check the reliability of scope fastening again.
For mounting and checking the serviceability of the scope
under daylight conditions do as follows:
-
put the cup with light filter on the lens;
7
-
remove the cover 8 and insert the battery as shown on the
cover of scope;
-
-
screw up the cover 8;
turn on the switch 7.
In 3-4 seconds the eyepiece field of view should begin to
gleam with yellow-green light and red aiming reticle;
-
adjust the optimal contrast of aiming reticule by means of
hand wheel 17;
-
if reticle is switched on but is extinct with the lit screen,
the battery should be replaced with operable one;
Warning: the reticle extinction indicates the discharge of
battery.
The central peak of reticle is assigned for sighting. The
vertical markers on each side of central peak can be used for
lateral deflection at moving target or strong wind. The scope
should be aligned to the weapon by means of zeroing. Zeroing
is carried out in the daytime and with the light filter cap put on
only, in the following order:
-
-
set the target of approximately 1x1 m at the range 100 m;
make the 3-4 shoots from rest at regular aiming of the
peak to centre of target;
-
determine the mean point of impact by holes placement.
If mean point of impact disagrees to aiming point more than
by 3 cm the scope alignment is needed. Align the scope by
mean of screws for vertical and horizontal adjustments. The
turn by one click corresponds to shift of mean point of impact
by 3 cm at the range of 100 m.
8
Note: If zeroing range is different, the value of click changes
proportionally, for example:
-
-
at range 50 m - 1.5 cm;
at range 200 m - 6.0 cm.
Example: On the Fig.3 the mean point of impact is located
above the aiming point by 15 cm and at the left by 20 cm. To
shift the mean point of impact to target centre one should turn
the vertical adjustment screw by 15/3 = 5 clicks down and the
horizontal adjustment screw by 20/3 = 7 clicks to the right.
Make the batch of check shooting.
Grouping of scope aimed shooting should not be worse than
without the scope. No adjustment should be made after
zeroing. When shooting a range exceeding 100 m you should
keep zeroing but choose another aiming point corresponding
to the distance to the target.
Figure 3.
9
6. MAINTENANCE
The device should be kept clean avoiding dust and dirt. The
outer surfaces of the optical parts should be clean always.
WARNING: It is prohibited:
-
-
to disassemble the scope;
to switch on the scope without protective cap and light
filter;
-
-
-
to apply exceeding force to clamp;
to use a battery of improper type;
to keep a battery into an unused scope for a long time.
The device is the subject of following periodic maintenance
procedure:
-
-
-
clean the scope against dust, dirt and moisture;
check out the contacts of power supply;
wipe grease spots on optical surfaces by clean napkin; in
case of significant pollution the alcohol can be used;
10
7. STORAGE
The scope must be prevented against mechanical damages.
The scope is to be stored in a heated room. Ambient
temperature must be within the limits from 5 to 35°C.
Relative humidity must not exceed 85%. It is recommended to
keep the scope in its caring case without a battery inserted.
11
8. TROUBLESHOOTING
The device does not work.
Check that the battery is installed properly.
Check the charge of the batteries. Replace if it is weak.
The image is degraded and blurred.
Clean the lens with napkin. If the inner optics suffers
from extended humidity send the scope to the
manufacturer for drying and sealing.
Unit flashes
It is normal for the unit to flash within the first 2 minutes of
activation. If the flashing continues afterwards the following is
a possible cause: bright environment (even with the caps
closed!)
12
Condensation accumulates on the parts.
It is O.K. to use the unit in cold. However, when the unit is
brought from the cold into a warm environment, it has to
warm up for up to 2 hours (not minutes!). Only then it is
allowed to turn it ON again.
Visibility decreases and / or disappears.
Bright light sources (moon, projectors or headlights)
may cause visibility to degrade or even completely
disappear. Move the device away from the light source
immediately. The image should be restored in within 2
minutes. Poor atmospheric conditions such as fog,
haze, or extremely dark environments will decrease the
visibility distance of the unit.
Reticle is absent or weak.
Check the batteries.
13
9. WARRANTY
NEWCON warrants this product against defects in material
and workmanship for one year from the date of the original
purchase, but no more than 18 months from the date of
manufacturing. Longer warranty is available, subject to the
terms of the specific sales contract. Should your Newcon
product prove to be defective during this period, please deliver
the product securely packaged in its original container or an
equivalent, along with the proof of the original purchase date,
to your Newcon Dealer.
Newcon will repair (or at its option replace with the same or
comparable model), the product or part thereof, which, on
inspection by Newcon, is found to be defective in materials or
workmanship.
What This Warranty Does Not Cover:
NEWCON is not responsible for warranty service should the
product fail as a result of improper maintenance, misuse,
abuse, improper installation, neglect, damage caused by
disasters such as fire, flooding, lightning, improper power
supply, or service other than by a NEWCON Authorized
Service.
Postage, insurance, and shipping costs incurred while
presenting your NEWCON product for warranty service are
your responsibility.
If shipping from North America, please, include a cheque or
money order payable to NEWCON OPTIK for the amount of
$15.00 to cover handling and return shipping.
14
10. CUSTOMER SUPPORT
Should you experience any difficulties with your NEWCON
OPTIK product, consult the enclosed manual. If the problem
remains unresolved, contact our customer support department
at (416) 663-6963 or toll free at 1-877-368-6666. Our
operating hours are 9am-5pm, Monday - Friday, Eastern
Standard Time. At no time should equipment be sent back to
Newcon without following the instructions of our technical
support department.
NEWCON OPTIK accepts no responsibility for unauthorized
returns.
To locate NEWCON Authorized Dealer call:
Tel: (416) 663-6963 Fax: (416) 663-9065
Email: [email protected]
The defective products should be shipped to:
From the USA only:
2331 Superior Ave. Cleveland, OH 44114
From all other countries:
105 Sparks Ave., Toronto, ON
M2H 2S5, CANADA
15
11. ACCEPTANCE CERTIFICATE
NIGHT VISION DEVICE NVS 4
Serial number: _________________________________
Complies with all technical specifications and has passed the
inspection.
Date of production: _________________________________
Quality Inspector: __________________________________
Quality Assurance Se
16
NEWCON OPTIK ™ 2010
Printed in Canada
|