INSTALLATION INSTRUCTIONS FOR PART 99-7425
APPLICATIONS
Nissan Rogue 2008-10
99-7425
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) Trim Plate • C) ISO Brackets
B
Harness & Antenna Connections (sold separately)
• 70-7552 - Nissan Harness 07-up
A
• 40-NI12 - Nissan Antenna Adapter 07-up
C
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
99-7425 DASH DISASSEMBLY
NISSAN Rogue 2008-10
A
1
2
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
If equipped with center speaker:
Unclip and remove the grille
(Figure A). Remove (4) Phillips screws
securing the speaker. Unplug and
remove the speaker. (Figure B).
Unclip the panel above the radio
including the a/c vents, then unplug
hazard switch and remove. (Figure C)
B
Note: If not equipped with center
speaker skip step number 2.
Continued on page 2.
C
1
99-7425 DASH DISASSEMBLY
NISSAN Rogue 2008-10
D
3
4
Unclip the panel below the radio
including the climate controls. Unplug
climate controls and remove the
panel. (Figure D)
Remove (4) Phillips screws securing
the radio, unplug and remove radio.
(Figure E)
Continue to kit assembly.
A/C
PASS
AIR BAG
E
2
99-7425 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
2
Slide the aftermarket radio into the
cage until it snaps into place.
(Figure B)
Continue to final assembly.
B
3
99-7425 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
A
1
Mount the ISO Brackets to the radio
with the screws supplied with the
radio. (Figure A)
2
3
Slide the radio into the radio housing
until it snaps into place. (Figure B)
Snap the trim plate onto the front of
the Radio Housing. (Figure B)
B
Continue to final assembly.
4
99-7425 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
5
99-7425 INSTRUCTIONS
1-800-221-0932
REV. 04/29/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-7425
|