KDC-DAB41U
KDC-DAB4551U
CIND-SRETCERIVUERCTION MANUAL
AMPLI-TUNER LECTEUR DE CD
SI DICHIARA CHE :
I lettori CD con Sintonizzatore AM/FM/DAB per auto Kenwood, modelli
KDC-DAB41U/ KDC-DAB4551U
risponde alle prescrizioni dell’art. 2 comma 1 del D.M. 28 agosto 1995, n. 548.
Fatto ad Uithoorn il 14 febbraio 2011
Kenwood Electronics Europe B.V.
Amsterdamseweg 37
1422 AC Uithoorn
The Netherlands
© 2011 Kenwood Corporation All Rights Reserved.
B64-4833-00/01 (EW)
Safety
Preparation
WARNING
How to attach/detach the faceplate
Stop the car before operating the unit.
Important to know...
To prevent a short circuit, never put or leave
1
1
■
2
any metallic objects (such as coins or metal
tools) inside the unit.
2
■
Caution: Adjust the volume so that you can
■
Do not expose the faceplate to direct
hear sounds outside the car. Driving with
the volume too high may cause an accident.
Condensation: When the car is air-
conditioned, moisture may collect on the
laser lens. This may cause disc read errors. In
this case, remove the disc and wait for the
moisture to evaporate.
sunlight, excessive heat, or humidity. Also
avoid places with too much dust or the
possibility of water splashing.
Keep the faceplate in its casing while
detached.
The faceplate is a precision piece of
equipment and can be damaged by shocks
or jolts.
■
■
■
■
The illustrations in this manual are examples
used to explain more clearly how the
controls are used. Therefore, what appears
on the illustrations may differ from what
appears on the actual equipment.
■
To prevent deterioration, do not touch the
terminals of the unit and faceplate with your
fingers.
■
If you experience problems during
installation, consult your Kenwood dealer.
When you purchase external components,
check with your Kenwood dealer to make
sure that they work with your model and in
your area.
How to reset your unit
If this unit fails to operate
■
properly, press the reset
button.
1
The unit returns to factory
settings when the reset
button is pressed.
2
3
Maintenance
Cleaning the unit: Wipe off the dirt on the
panel with a dry silicon or soft cloth. Failure
to observe this precaution may result in
damage to the monitor or unit.
Cleaning the connector: Wipe off dirt on
the connector of the unit and faceplate. Use
a cotton swab or cloth.
Reset button
Remote controller
KDC-DAB41U/ KDC-DAB4551U can also
be remotely controlled with an optionally
purchased remote controller.
English 3
Basic Operations
Volume knob
Loading slot
Ejects the disc
LIST
UPDATE
Detaches the faceplate
Display window
USB terminal
Auxiliary input jack
The following indicator lights up when...
ST: A stereo broadcast is received.
D: DAB service is received. Flashes when
changed to Radio Data System service.
Slide open the cover
MC: Secondary service in DAB is available.
Flashes when secondary service is
selected.
RDS: Radio Data System service is available.
TI: Traffic Information function is turned on.
IN: A disc is in the unit.
ATT: The sound attenuates.
EQ: [SYSTEM Q] is set to an EQ mode other
than [NATURAL]. (page 28)
B.BOOST: [BASS BOOST] is set to [1] or [2].
(page 28)
: Indicates that the Music Search mode is
selected now.
Muting upon the reception of a
phone call
To use this feature, connect the MUTE lead
to your telephone using a commercial
telephone accessory. (See page 32.)
When a call comes in, “CALL” appears.
■
The audio system pauses.
To continue listen to the audio system
■
during a call, press SRC. “CALL” disappear
and the audio system resumes.
BT: Bluetooth cell-phone connection status.
When a call ends, “CALL” disappear.
■
The audio system resumes.
4
English
When you press or hold the following button(s)...
Main unit
General operation
■
■
Turns on.
Turns off if pressed and held.
Selects the available sources (DAB, TUNER, USB or iPod, CD, AUX, STANDBY), if
the power is turned on.
SRC
• If the source is ready, playback also starts. “iPod” and “CD” are selectable only
when an iPod is connected or a disc is loaded.
Adjusts the volume level.
Volume knob
(turn)
Selects items.
Confirms selection.
Enters [FUNCTION] settings.
Volume knob
(press)
■
Selects the FM bands (FM1/ FM2/ FM3) or MW/ LW.
Selects the DAB bands (DB1/ DB2/ DB3).
Selects the next folder.
■
BAND
6 (38)
■
Pauses/resumes playback of a disc/ USB device/ iPod.
■
Searches for radio station.
Selects track/file.
■
4 / ¢
■
Fast-forwards/reverses tracks/files if pressed and held.
■
Changes the display information.
Scrolls the display information if pressed and held.
Enters clock adjustment mode directly (page 6) if pressed and held while in
■
SCRL DISP
DAB
■
clock display screen.
Changes to DAB source if other than DAB source has been selected.
Enters DAB Service Search mode while in DAB source.
Updates DAB search list information or stops update if pressed and held.
■
■
■
Returns to the previous item.
Exit from setting mode.
• Press and hold on the main unit will also exit from the setting mode.
■
■
Updating DAB search list information takes up to 3 minutes. No interruption such as DAB sound and operation or traffic information
is possible while updating.
“LIST UPDATE” is displayed and update starts. “UPDATED” is displayed when update completes.
English 5
Getting Started
Canceling the display
demonstration
Adjusting the clock
1 Press the volume knob to enter
[FUNCTION] mode.
The display demonstration is always turned
on unless you cancel it.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select [CLOCK],
then press to enter.
When you turn on the power (or after you
reset the unit), the display shows:
[CANCEL DEMO] \ [PRESS] \ [VOLUME 4 Turn the volume knob to select [CLOCK
KNOB]
ADJUST], then press to enter.
Clock hour flashes on the display.
1 Press the volume knob.
[YES] is selected as the initial setup.
2 Press the volume knob again to confirm.
[DEMO OFF] appears.
5 Turn the volume knob to adjust the hour,
then press to enter minute adjustment.
Clock minutes flashes on the display.
6 Turn the volume knob to adjust the
minute, then press to confirm.
■
If no operation is done for about 15 seconds
or if you turn the volume knob to select
[NO] in step 2, [DEMO MODE] appears and
the display demonstration starts.
Press 4 / ¢ to move between the
hour and minute adjustment.
7 Hold
to finish the procedure.
Setting the demonstration mode
1 Press the volume knob to enter
[FUNCTION].
2 Turn the volume knob to select [DEMO
MODE], then press to enter.
3 Turn the volume knob to select [ON] or
[OFF].
Initial settings before operations
1 Press SRC to enter [STANDBY] mode.
2 Press the volume knob to enter
[FUNCTION] mode.
3 Turn the volume knob to select [INITIAL
SET], then press to enter.
If [ON] is selected, display demonstration
starts if no operation is done for about 20
seconds.
4 Turn the volume knob to make a
selection, then press to confirm.
■
See table below for selection.
■
4 Hold
to finish the procedure.
Repeat step 3 until the desired item is
selected/activated.
Press to return to the previous item.
■
5 Hold
to finish the procedure.
6
English
Item
Selectable setting (Preset: *)
PRESET TYPE
NORMAL *: Memorizes one station or channel for each preset button in each band (FM1/ FM2/ FM3/ MW/ LW/
DB1/ DB2/ DB3). ; MIX: Memorizes one station or channel for each preset button regardless of the selected band
(FM1/ FM2/ FM3/ MW/ LW/ DB1/ DB2/ DB3).
KEY BEEP
ON */ OFF: Activates/deactivates the keypress tone.
P-OFF WAIT
Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.
––– : Cancels ; 20M *: 20 minutes ; 40M: 40 minutes ; 60M: 60 minutes
RUSSIAN SET
BUILT-IN AUX
ON: Folder name, file name, song title, artist name, album name are displayed in Russian (if applicable). ;
OFF *: Cancels.
ON1 *: Outputs sound of the connected external component through the car speakers when “AUX” is selected as
the source. ; ON2: Outputs sound from the connected external component when “AUX” is selected as the source.
When you turn on the power, the sound attenuates (to prevent noise when no external component is connected).
Turn the volume knob clockwise to return to the previous volume level. ; OFF: Disables “AUX” in source selection.
1 *: Automatically distinguishes between audio file disc and music CD. ; 2: Forces to play as a music CD. No sound
can be heard if an audio file disc is played.
CD READ
SWITCH PREOUT REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the
rear of the unit (through an external amplifier).
SP SELECT
OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.
DAB ANT POWER ON *: Supplies power to the DAB antenna. Set when using the antenna included with KDC-DAB41U. ;
OFF: Does not supply power. Set when using passive antenna without booster.
DAB L-BAND
ON: Receives L-BAND ensemble with DAB source. ; OFF *: Set when there is no L-BAND broadcast station.
Ensemble search and service list information update will be faster.
F/W
UPDATE SYS
UPDATE
DAB
UPDATE The current firmware version is displayed.
Press the volume knob to update DAB or system firmware.
YES: Starts upgrading the firmware. ; NO *: Cancels (upgrading is not activated).
English 7
Listening to the DAB
Hold to turn on or off the Traffic Information function.
LIST
UPDATE
■
■
■
■
Hold for about 2 seconds to memorize the current
service or the selected Program Type. (Refer to [PTY
SEARCH] on the table below to select the Program
Type.)
Press briefly to recall memorized service (or Program
Type after entering the PTY search mode).
Changes to DAB source if other than
DAB source has been selected.
Press briefly to enter DAB service
search mode
Updates DAB search list information
or stops update if pressed and held.
■
2 Turn the volume knob to select a service,
1 Press SRC to select “DAB”.
2 Press BAND repeatedly to select a band
(DB1, DB2, DB3).
3 Press and hold 4 / ¢ to search for an
ensemble.
then press to confirm.
To skips character, press 4/ ¢.
To cancel the Service Search mode, press
■
■
and hold
.
■
“NO LIST” is displayed when no service list
is obtained.
4 Press 4 / ¢ to select an ensemble,
service or component to listen.
■
Press ¢ to receive ensemble, then select
Alphabet Search for service
1 Press DAB to enter Service Search mode.
“SERVICE LIST” appears.
2 Press to enter alphabet search mode.
“< ABCDEFG >” appears.
service > component in sequence. When
4 is pressed, primary service is selected
when ensemble changes and primary is
selected when service changes.
3 Turn the volume knob to select the
character to be searched for.
■
Ensemmbblle
Service
To move to the next row, press BAND.
To skips character, press 4/ ¢.
■
: Press
: Press
4
¢
.
.
Primary
4 Press the volume knob to start searching.
To return to the Service Search mode, press
Secondarryy
Service
Service
■
.
■
To cancel the Service Search mode, press
and hold
.
Selecting a service
• The service list information must be obtained
first.
■
To search for a character other than A to Z
and 0 to 9, enter only “ * ”.
1 Press DAB to enter Service Search mode.
“SERVICE LIST” appears.
Updating Service List information
Press and hold DAB to start Service list
update.
8
English
■
■
Press and hold DAB to cancel service list
update.
There is no DAB sound and no operation
can be performed while service list is
updating. It may take as long as three
minutes.
Adjust [SETTINGS] mode settings
While listening to the service...
1 Press the volume knob to enter
[FUNCTION] mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to make a
selection, then press to confirm.
See table below for selection.
Display Selection
Press DISP repeatedly to select an
information.
4 Hold
to finish the procedure.
SERVICE LABEL (Service label) ; DYNAMIC
LABEL (Dynamic label ) ; PTY LABEL (PTY
label ) ; ENSEMBLE (Ensemble label) ; DAB
LEVEL (Signal strength ; “LV STRONG”: Good
; “LV WEAK”: Bad ; “NO SIG”: No signal) ; BIT
RATE (Transmission speed of the audio
service) ; FREQUENCY ; CLOCK
Item
SEEK MODE
Selectable setting (Preset: *)
Selects the tuning mode for 4 / ¢ buttons.
Press
4
/
¢
.
Press and hold
4
/
¢
.
AUTO1 * Select an ensemble, service or component
AUTO2 Search in the order of the services in the preset
memory.
Automatically search for an ensemble.
–
MANUAL Select an ensemble, service or component
Manually search for an ensemble.
PRIORITY
DRC
ON *: Switches automatically to FM and enables listening of same program when DAB signal strength becomes
weak. In DAB to FM case, the unit keeps DAB source. And it returns DAB sound when DAB reception becomes good
again. Also, when listening to FM, switches to DAB source if there is same program in DAB. ;
OFF: Cancels (Does not switch automatically).
ON: Adjusts the dynamic range of the sound when the program has Dynamic Range Control (DRC). ;
OFF *: Does not adjust the dynamic range.
ASW SELECT Sets the interrupting announcement (page 10).
Turn the volume knob to select the announcement. Press the volume knob to turn on (“*” appears) or off.
•
Exiting the interruption: Switch the setting of the interruption of the item being interrupted from permission to
prohibition.
•
Set the displayed language with [LANGUAGE SEL]. (page 10)
DAB LIST UPDT AUTO *: Automatically updates the DAB service list when ACC is turned ON. ;
MANU: Updates the DAB service list when DAB button is pressed.
PTY SEARCH
PTY WATCH
Selects the available Program Type (page 10). Then, press
4
/
¢
to start searching.
•
Set the displayed language with [LANGUAGE SEL]. (page 10)
After registering a desired programme type, when the programme in the registered type starts in the Ensemble
being received, the Service is automatically switched.
PTY WATCH OFF: Cancels (does not change) ; Selects the available Program Type (page 10). (except SPEECH and
MUSIC)
•
Set the displayed language with [LANGUAGE SEL]. (page 10)
Continued to next page
English 9
Item
Selectable setting (Preset: *)
LANGUAGE SEL Sets the language to be used for DAB source [ASW SELECT/ PTY SEARCH/ PTY WATCH], and TUNER source
[PTYSEARCH].
ENGLISH */ FRENCH/ GERMAN
■
[PRIORITY/ ASW SELECT/ DAB LIST UPDT] If other playback source is selected, these settings are selectable under [DAB SET]
item. (page 29)
■
Available Program Type:
SPEECH; MUSIC; NEWS; AFFAIRS; INFO; SPORT; EDUCATE; DRAMA; CULTURE; SCIENCE; VARIED; POP M (music); ROCK M (music);
EASY M (music); LIGHT M (music); CLASSICS; OTHER M (music); WEATHER; FINANCE; CHILDREN; SOCIAL; RELIGION; PHONE IN;
TRAVEL; LEISURE; JAZZ; COUNTRY; NATION M (music); OLDIES; FOLK M (music); DOCUMENT
The unit will search for the Program type categorized under [SPEECH] or [MUSIC] if selected.
[SPEECH] : Roman typeface item. ; [MUSIC] : Italic typeface item.
■
■
Available Announcement:
TRAVEL NEWS, WARNING, NEWS, WEATHER, EVENT, SPECIAL, RAD INF (information), SPORTS, FINANCE.
If the volume is adjusted during reception of announcement, the adjusted volume is
memorized automatically. It will be applied the next time announcement function is turned
on.
Listening to the Radio
Hold to turn on or off the Traffic Information function.
LIST
UPDATE
■
Hold for about 2 seconds to memorize the current station or the selected Program
Type. (Refer to [PTY SEARCH] on the table below to select the Program Type.)
Press briefly to recall memorized station (or Program Type after entering the PTY
■
search mode).
Display Selection
Press DISP repeatedly to select an
information.
1 Press SRC to select “TUNER”.
2 Press BAND repeatedly to select a band
(FM1, FM2, FM3, MW/LW).
FM: FREQUENCY/PS (Frequency or Program
Service name) ; TITLE/ARTIST *1 (Song
title or artist name) ; STATION NAME *1 ;
RADIO TEXT+ *1 ; RADIO TEXT ; CLOCK
AM: FREQUENCY ; CLOCK
3 Press 4 / ¢ to search for a station.
• *1 Information of Radio text plus is displayed.
10 English
Adjust [SETTINGS] mode settings
While listening to the radio...
1 Press the volume knob to enter [FUNCTION] mode.
2 Turn the volume knob to select [SETTINGS], then press to enter.
3 Turn the volume knob to make a selection, then press to confirm.
See table below for selection.
4 Hold
Item
to finish the procedure.
Selectable setting (Preset: *)
LOCAL SEEK
SEEK MODE
ON: Searches only FM stations with good reception. ; OFF *: Cancels.
Selects the tuning mode for 4 / ¢ buttons.
AUTO1 *: Automatically search for a station. ; AUTO2: Search in the order of the stations in the preset memory. ;
MANUAL: Manually search for a station.
AUTO MEMORY YES: Automatically starts memorizing 6 stations with good reception. ; NO *: Cancels (automatic memorizing is
not activated). (Selectable only if [NORMAL] is selected for [PRESET TYPE].) (page 7)
MONO SET
PTY SEARCH
ON: Improves the FM reception (but the stereo effect may be lost). ; OFF *: Cancels (stereo effect resumes).
Selects the available Program Type (page 11). Then, press to start searching.
Set the displayed language with [LANGUAGE SEL].
4
/
¢
•
LANGUAGE SEL Sets the language to be used for DAB source [ASW SELECT/ PTY SEARCH/ PTY WATCH], and TUNER source
[PTYSEARCH].
ENGLISH */ FRENCH/ GERMAN
NEWS SET
AF SET
00M – 90M: Sets the time for receiving the next news bulletin. ; OFF *: Cancels.
ON *: Automatically searches for another station broadcasting the same program in the same Radio Data System
network with better reception when the current reception is poor. ; OFF: Cancels.
REGIONAL
ON *: Switches to another station only in the specific region using the “AF” control. ; OFF: Cancels.
AUTO TP SEEK ON *: Automatically searches for a station with better reception when the traffic information’s reception is poor.
; OFF: Cancels.
■
[LOCAL SEEK/ MONO SET/ PTY SEARCH/ LANGUAGE SEL] is selectable only when the source is “FM”.
[NEWS SET/ AF SET/ REGIONAL/ AUTO TP SEEK] is selectable only when the source is “FM”. If other playback source is selected,
these settings are selectable under [TUNER SET] item. (page 29)
■
■
Available Program Type:
SPEECH; MUSIC; NEWS; AFFAIRS; INFO; SPORT; EDUCATE; DRAMA; CULTURE; SCIENCE; VARIED; POP M (music); ROCK M (music);
EASY M (music); LIGHT M (music); CLASSICS; OTHER M (music); WEATHER; FINANCE; CHILDREN; SOCIAL; RELIGION; PHONE IN;
TRAVEL; LEISURE; JAZZ; COUNTRY; NATION M (music); OLDIES; FOLK M (music); DOCUMENT
The unit will search for the Program type categorized under [SPEECH] or [MUSIC] if selected.
[SPEECH] : Roman typeface item. ; [MUSIC] : Italic typeface item.
■
■
The Radio Data System feature won’t work where the service is not supported by any
broadcasting station.
If the volume is adjusted during reception of traffic information, the adjusted volume is
memorized automatically. It will be applied the next time Traffic Information function is
turned on.
English 11
Listening to a Disc/ USB device/ iPod
Ejects the disc.
Detach the faceplate
(“NO DISC” appears and “IN” indicator goes off.)
LIST
UPDATE
■
Press to select track/file.
Hold to fast-forwards/reverses.
USB terminal
■
Press to pause. Press again
to resume playback.
■
■
Press to select next folder of Audio
File/iPod.
Press to select next disc of CD changer
(optional accessory).
Start playing a disc
1 Press SRC to turn on the power.
2 Insert a disc into the loading slot.
Playback starts automatically.
Apple iPod
(commercially available)
Start playing a USB device or iPod
1 Press SRC to turn on the power.
2 Slide the cover to open it.
3 Connect a USB device or iPod to the USB
terminal.
KCA-iP102
(optional accessory)
The source automatically switches, and
playback starts.
Removing the USB device or iPod
1 Press SRC to select a source other than
“USB” or “iPod”.
2 Remove the USB device or iPod.
Start playing the disc changer
(optional accessory)
USB device
(commercially available)
• Only with the optional accessory CD changer
connected.
1 Press SRC to turn on the power.
2 Press SRC to select “CD CHANGER”.
CA-U1EX
(optional accessory)
12 English
Selecting Repeat Play
Press number button 4 (REP) repeatedly
to make a selection.
Audio CD : TRACK REPEAT, REPEAT OFF
Audio File :
Selecting Scan Play
Press number button 2 (SCAN)
repeatedly to make a selection.
Audio CD : TRACK SCAN, SCAN OFF
Audio File : FILE SCAN, SCAN OFF
CD changer : TRACK SCAN, SCAN OFF
FILE REPEAT, FOLDER REPEAT, REPEAT OFF
iPod :
■
If scan play is selected, the unit starts
FILE REPEAT, REPEAT OFF
CD changer : TRACK REPEAT, DISC REPEAT,
REPEAT OFF
playing the first 10-second intro of the
music in the disc/current folder.
If “SCAN OFF” is selected, the unit resumes
normal play of the current song.
Selecting Random Play
Selecting a folder/track/file
• Not available if disc changer playback is
selected.
1 Press to enter Music Search mode.
“SEARCH” appears, then the current file
name appears on the display.
Press number button 3 (ALL RDM)
repeatedly to make a selection.
Audio CD : DISC RANDOM, RANDOM OFF
Audio File/ iPod :
FOLDER RANDOM, RANDOM OFF
CD changer : DISC RANDOM, RANDOM OFF
2 Turn the volume knob to select a folder/
track/ file, then press to confirm.
To skip songs, press 4/ ¢. Holding
4/ ¢ skips songs at 10% regardless of
the setting made. (page 15)
All Random Play
Press and hold number button
3 (ALL RDM).
Pressing this button again plays songs in
the normal mode starting.
Audio File/ iPod :
■
This operation is effective only for the iPod
or Kenwood Music Editor media.
To return to the root folder (audio file), top
ALL RANDOM, RANDOM OFF
Changes the iPod browsing item to “songs”.
■
■
menu (iPod) or first track (audio CD), press
BAND.
Selecting Magazine Random Play
• Only when the source is CD changer.
Press number button 5 repeatedly to
make a selection.
■
To return to the previous folder, press
To cancel the Music Search mode, press and
hold
< or > on the display indicates that
preceded/next item is available.
.
■
.
■
CD changer : MGZN (magazine) RANDOM,
RANDOM OFF
English 13
Playing a song on the playlist
1 Press number button
5 (MEMO MY LIST) to display the playlist.
“MY PLAYLIST” appears.
Alphabet Search for iPod
1 Press to enter Music Search mode.
“SEARCH” appears.
2 Turn the volume knob to select a
category, then press to confirm.
3 Press again to enter alphabet search
mode.
2 Turn the volume knob to select the song
you want, then press to confirm.
■
Random play cannot be performed during
playback of a song in the playlist.
“SEARCH <– – –>” appears.
4 Turn the volume knob to select the
character to be searched for.
5 Press 4 / ¢ to move to the entry
position.
You can enter up to three characters.
6 Press the volume knob to start searching.
After this step, see step 2 of <Selecting a
folder/track/file> (page 13) to select a song.
Deleting a song on the playlist
1 Press number button 5 (MEMO MY LIST)
to display the playlist.
“MY PLAYLIST” appears.
2 Turn the volume knob to select the song
you want to delete, then press and hold
the volume knob.
3 Turn the volume knob to select [DELETE
ONE] or [DELETE ALL], then press to
confirm.
Select “DELETE ALL” to delete all the songs
in the playlist.
4 Turn the volume knob to select [YES],
then press to confirm.
“COMPLETED” appears.
■
To return to the Music Search mode, press
.
■
To cancel the Music Search mode, press and
hold
.
■
■
■
A longer searching time is required if there
are many songs or playlists in the iPod.
To search for a character other than A to Z
and 0 to 9, enter only “ * ”.
The article (a, an, the) of songs name will be
skipped during search.
iPod control by Hand mode
Press number button 1 (iPod) repeatedly
to make a selection.
My Playlist for iPod
HANDS ON :
Registering songs in the playlist
1 Select and play the song you want to
register. (page 13)
2 Press and hold number button
5 (MEMO MY LIST) to register.
“## STORED” (registration number) appears.
You can register up to 10 songs. “MEMORY
FULL” appears, if you try to register the
eleventh song.
Control iPod from the iPod.
This mode is not compatible with music
■
information display. The display will show
“iPod MODE”.
HANDS OFF: Control iPod from the unit.
■
If you attempt to register a song from
a different iPod, “NO INFO” followed by
“MPLIST DELETE” appears.
To delete the playlist, turn the volume knob
to select “YES”, then press to confirm.
You can also register the song displayed in
■
the Music Search mode by following the
same procedure.
Do not register Podcasts.
■
14 English
Adjust [SETTINGS] mode settings
While listening to an iPod or KENWOOD Music
Editor media ...
1 Press the volume knob to enter
[FUNCTION] mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to make a
selection, then press to confirm.
See the following table for selection.
4 Hold
to finish the procedure.
Item
Selectable setting (Preset: *)
SKIP SEARCH 0.5% */ 1%/ 5%/ 10%: Sets the ratio of skip
when searching for a song in Music Search
mode.
MPLIST
DELETE
YES: Deletes the saved My Playlist. ;
NO *: Cancels.
■
[MPLIST DELETE] is selectable only when the source is
“iPod”.
English 15
■
Handling discs
Do not touch the recording surface of
Detailed information and notes about the
playable audio files are stated in an online
manual on the following site:
■
the disc.
■
Do not stick tape etc. on the disc, or use a
disc with tape stuck on it.
Do not use any accessories for the disc.
Clean from the center of the disc and
■
About USB device
■
■
This unit can play audio files stored on a
move outward.
Clean the disc with a dry silicon or soft
USB mass storage class device.
Install the USB device in the place where
■
■
cloth. Do not use any solvents.
When removing discs from this unit, pull
them out horizontally.
Remove the rims from the center hole
it will not prevent you from driving your
vehicle properly.
You cannot connect a USB device via a
USB hub and Multi Card Reader.
Make sure all important data has been
■
■
■
■
and disc edge before inserting a disc.
backed up to avoid losing the data.
Connecting a cable whose total length
■
Discs that cannot be used
■
This unit can only play the CDs with:
is longer than 5 m can result in abnormal
playback.
A USB connection cable, CA-U1EX
■
(optional accessory) is required for
connecting a USB device.
■
Discs that are not round.
Discs with coloring on the recording
■
surface or discs that are dirty.
You cannot play a Recordable/ReWritable
disc that has not been finalized. (For the
finalization process refer to your disc
writing software, and your disc recorder
instruction manual.)
3-inch CD cannot be used. Attempt
to insert using an adapter can cause
malfunction.
About compatible iPod/iPhone
Made for
■
– iPod touch (4th generation)
– iPod touch (3rd generation)
– iPod touch (2nd generation)
– iPod touch (1st generation)
– iPod classic
■
– iPod with video
– iPod nano (6th generation)
– iPod nano (5th generation)
– iPod nano (4th generation)
– iPod nano (3rd generation)
– iPod nano (2nd generation)
– iPod nano (1st generation)
– iPhone 4
– iPhone 3GS
– iPhone 3G
– iPhone
About Audio file
Playable Audio file
■
: AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)
Playable disc media: CD-R/RW/ROM
Playable disc file format: ISO 9660 Level
■
■
1/2, Joliet, Romeo, Long file name.
Playable USB device file system: FAT16,
■
FAT32
Although the audio files are complied with
the standards listed above, the play maybe
impossible depending on the types or
conditions of media or device.
(As of January 2011)
Latest compatible list of iPod/iPhone.
For details, see:
■
16 English
■
■
Type of control available varies depending
on the type of connected iPod.
For details, see above URL.
The word “iPod” appearing in this manual
indicates the iPod or iPhone connected to
this unit with a connection cable, KCA-
iP102 (optional accessory).
If you start playback after connecting the
iPod, the music that has been played by
the iPod is played first.
■
In this case, “RESUMING” is displayed
without displaying a folder name, etc.
Changing the browse item will display a
correct title, etc.
You cannot operate iPod if “KENWOOD” or
“✓” displayed on iPod.
■
About “KENWOOD Music Editor”
■
This unit supports the PC application
“KENWOOD Music Editor Light ver1.1” or
later.
When you use the audio file with
■
database information added by the
“KENWOOD Music Editor Light ver1.1”, you
can search a file by title, album or artist
name using Music Search (page 13).
■
In the Instruction manual, the term “Music
Editor media” is used to mean the device
that contains audio files with database
information added with KENWOOD Music
Editor.
■
“KENWOOD Music Editor Light ver1.1” is
available from the following web site:
For further information on “KENWOOD
■
Music Editor Light ver1.1”, refer to the site
above or the application help.
English 17
Operation of Hands-Free Phoning
Preparation : Only with the optional accessory KCA-BT300 or KCA-BT200 connected.
LIST
UPDATE
■
■
■
Press and hold for about 2 seconds to memorize the
current phone number.
Press briefly to recall memorized phone number.
Press and hold to enter
Bluetooth mode.
Press to answer an incoming
call.
■
Step 2. Connection
Getting Started
If you have registered 2 or more cell-
phones, you need to select one of them.
For more details, see <Selecting the
Bluetooth Device> (page 23).
When a cell-phone is connected, the “BT”
indicator lights up.
Step 3. Hands-free phoning
You can do hand-free phoning when the
connection is made.
When registering from this unit. Refer to
<Registering Bluetooth Device (Pairing)>
(page 22).
For details on the Bluetooth cell-phone with
the hands-free function, see <About the
Cell-Phone> (page 25).
Before use the Bluetooth device, you need
to connect Bluetooth device to this unit. The
following 3 steps procedure is necessary.
Step 1. Pairing (Registering from Bluetooth
devices)
1 Press SRC to turn on the power.
2 Start registering this unit by operating
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit (pairing). Select “KCA-
BT300” or “KCA-BT200” from the list of
connected units.
3 Input the PIN code (“0000”) in the
Bluetooth device.
■
■
Check that registration is complete on
the Bluetooth device. PIN code is set to
“0000” as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page 24).
4 By operating the Bluetooth device, start
hands-free connection.
18 English
■
The category items in the Phone Book are
displayed as follows.
GE: General ; HM: Home ; OF: Office ;
MO: Mobile ; OT: Other
Making a Call
1 Press and hold the volume knob to enter
Bluetooth mode.
2 Turn the volume knob to select a dialing
method, then press to enter.
Calling a Number in the Call Log
2 Turn the volume knob to select the
“OUTGOING” (outgoing call), “INCOMING”
(incoming call), or “MISSED CALLS”
(missed call), then press to enter.
3 Turn the volume knob to select a name or
phone number.
■
Operation method of each mode is
described below.
–
“PHONE BOOK”: Calling a Number in the
Phone Book
“OUTGOING”/ “INCOMING”/ “MISSED
–
CALLS”: Calling a Number in the Call
Log
“NUMBER DIAL”: Dial a Number
4 Press the volume knob to make a call.
■
–
The outgoing call list and the incoming call
–
“VOICE RECOG”: Make a Voice Dialing
list, and the missed call list are the lists of
calls originated from and received at this
unit. They are not the ones stored in the
cell-phone memory.
Call
–
Speed Dialing (Preset Dial)
■
To switch between name and phone
number, press DISP.
To return to the Bluetooth mode, press and
■
Dial a Number
hold
.
2 Turn the volume knob to select “NUMBER
DIAL”, then press to enter.
3 Turn the volume knob repeatedly
to enter digits of a phone number
sequentially
■
To exit Bluetooth mode, press SRC.
Calling a Number in the Phone Book
2 Turn the volume knob to select “PHONE
BOOK”, then press to enter.
3 Press to enter alphabet search mode.
4 Turn the volume knob to select the
character to be searched for.
■
To move to the next digit, press ¢.
■
To delete the last digit, press 4.
■
You can input max 32 digits.
4 Press the volume knob to make a call.
■
To move to the next row, press BAND.
To return to the Phone Book mode, press
.
■
Speed Dialing (Preset Dial)
2 Press number button (1 – 6).
3 Press the volume knob to make a call.
5 Press the volume knob to start searching.
6 Turn the volume knob to select a name
and category.
■
To move to the next character, press 4
/ ¢.
7 Press the volume knob to make a call.
■
To use the Phone Book, it must be
downloaded to this unit in advance. Refer to
<Downloading the Phone Book> (page 21).
During search, a non-accent character such
■
as “u” is searched for instead of an accent
character such as “ü”.
Continued to next page
English 19
Registering to the Preset Dial Number
(Preset Memory)
2 Enter the phone number with reference
to the following:
Dial a number/ Calling a number in the call
log/ Calling a number in the Phone Book
3 Press and hold number button (1 – 6) for
about 2 seconds.
Receiving a Call
Answering a Phone Call
Press the volume knob.
Rejecting an Incoming Call
Press SRC.
During a Call
Disconnecting a Call
Press SRC.
Switching to the Private Mode
Press number button 6 to switch
between Private talk (“PRIVATE TALK”)
and Hands-free talk (“HANDS FREE”).
Make a Voice Dialing Call
2 Turn the volume knob to select “VOICE
RECOG”, then press to enter.
“V-RECG READY” is displayed.
3 Press the volume knob to start voice
recognize.
4 “PB NAME” is displayed.
When a beep is heard, say the name within
2 seconds.
5 “PN TYPE” is displayed.
When a beep is heard, say the category
name within 2 seconds.
The recognized phone number (name) is
displayed.
Call Waiting
Answering Another Incoming Call with the
Current Call Suspended
Turn the volume knob to select
[ANSWER], then press to enter.
Continuing the Current Call
Turn the volume knob to select [REJECT],
then press to enter.
Switching between the Current Call and
Waiting Call
Press the volume knob to switch the
calling party.
6 Press the volume knob to make a call.
■
This step is the same as step 4 of the
procedure in <Calling a Number in the
Phone Book> (page 19). You can make a
call or select a category.
Clearing the Disconnection
Message
Press and hold the volume knob.
“HF DISCONCT” disappears.
■
If your voice cannot be recognized, a
message is displayed. Pressing the Volume
knob allows you to retry voice input. Refer
to <Troubleshooting> (page 37).
■
Both the name and category require
registration of a voice tag. Refer to <Setting
a Voice Command> (page 23).
Audio sound is not output during voice
■
recognition.
20 English
Downloading the Phone Book
To download automatically
If the cell-phone supports a phone book
synchronization function, the phone
book is downloaded automatically after
Bluetooth connection.
Setting on the cell-phone may be required.
If no phone book data is found in the unit
■
■
even after the completion of downloading,
your cell-phone may not support automatic
download of phone book data. In this case,
try downloading manually.
To download from the cell-phone manually
1 By operating the cell-phone, end the
hands-free connection.
2 By operating the cell-phone, download
the phone book data to this unit
■
During downloading: “DOWNLOADING”
is displayed.
After completion of downloading:
■
“COMPLETE” is displayed.
3 By operating the cell-phone, start the
hands-free connection.
■
To clear the downloading completion
message, press any button.
Up to 1000 phone numbers can be
■
registered for each registered cell-phone.
Up to 32 digits can be registered for each
■
phone number along with up to 50*
characters representing a name.
(* 50: Number of alphabetical characters.
Fewer characters can be input depending
on the type of characters.)
■
To cancel downloading of the phone book
data, operate the cell-phone.
English 21
Bluetooth Setup
Preparation : Only with the optional accessory KCA-BT300 or KCA-BT200 connected.
8 Input the PIN code
Registering Bluetooth Device
(Pairing)
Registering from Bluetooth devices
1 Press SRC to turn on the power.
2 Start registering this unit by operating
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit (pairing). Select “KCA-
BT300” or “KCA-BT200” from the list of
connected units.
3 Input the PIN code (“0000”) in the
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
“0000” as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page 24).
■
Turn the volume knob to select the
number.
■
To move to the next digit, press ¢.
■
To delete the last digit, press 4.
9 Press the volume knob to transmit the
PIN code.
If “PAIRING OK” is displayed, registration is
completed. If the error message appears
even though the PIN code is correct, try
Registering Special Bluetooth device.
When “CONFIRM PHONE” is displayed,
confirm connection with a cell-phone
operation.
10 Hold
to finish the procedure.
■
To exit Bluetooth mode, press SRC.
If there are 5 or more Bluetooth devices
registered, you cannot register a new
Bluetooth device.
■
4 By operating the Bluetooth device, start
hands-free connection.
Registering Special Bluetooth device
1 Press and hold the volume knob to enter
Bluetooth mode.
Registering from this unit
1 Press and hold the volume knob to enter
Bluetooth mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select
[PAIRING], then press to enter.
4 Turn the volume knob to select [S-DVC
SELECT], then press to enter.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select
[PAIRING], then press to enter.
4 Turn the volume knob to select [DEVICE
SEARCH], then press to enter.
5 Press the volume knob to search for the
Bluetooth device.
5 Turn the volume knob to select a device
name, the press to confirm.
6 Go through the procedure step 4
of <Registering from this unit> and
complete the registration (pairing).
If the device name is not in the list, select
“OTHER PHONE”.
When search is completed, “FINISHED” is
displayed.
6 Turn the volume knob to select a
Bluetooth device name, press to confirm.
7 “PAIRING” is displayed (KCA-BT300 only)
If “PAIRING OK” is displayed, proceed to
step 10.
■
If “PIN CODE NG” is displayed, proceed to
steps 8.
22 English
6 Turn the volume knob to select [PB
Selecting the Bluetooth Device
1 Press and hold the volume knob to enter
Bluetooth mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select
[PAIRING], then press to enter.
4 Turn the volume knob to select [PHONE
SELECT] or [AUDIO SELECT], then press
to enter.
NAME REG], then press to enter.
■
To select “PB NAME CHK”, play the
registered voice.
To select “PB NAME DEL”, delete a voice
■
tag. Turn the volume knob to select “YES”,
then press to confirm.
7 “ENTER 1” is displayed. When a beep is
heard, say a voice tag within 2 seconds.
8 “ENTER 2” is displayed. When a beep is
heard, say the same voice tag as that you
said in step 7 within 2 seconds.
5 Turn the volume knob to select a
Bluetooth device name.
“COMPLETE” is displayed.
9 Press the volume knob to return to step
6 Press the volume knob to set up the
Bluetooth device.
5.
■
“✱(Device name)”: The selected Bluetooth
■
To exit Setting mode, press
.
device is busy.
“-(Device name)”: The selected Bluetooth
■
■
■
To exit Bluetooth mode, press SRC.
You can register up to 35 voice tags.
Audio sound is not output during voice tag
registration.
■
device is on standby.
“ (Device name)“: The Bluetooth device is
■
deselected.
If a cell-phone is already selected,
■
Registering Phone Book Name Type
1 Press and hold the volume knob to enter
Bluetooth mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select [VOICE
TAG], then press to enter.
deselect it, and then select a different
one.
7 Hold
to finish the procedure.
■
To exit Bluetooth mode, press SRC.
Setting a Voice Command
Registering Phone Book Name
1 Press and hold the volume knob to enter
Bluetooth mode.
4 Turn the volume knob to select [PN TYPE
EDIT], then press to enter.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select [VOICE
TAG], then press to enter.
4 Turn the volume knob to select [PB
NAME EDIT], then press to enter.
5 Search for the Phone Book name to
register
5 Turn the volume knob to select
[GENERAL], [HOME], [OFFICE], [MOBILE],
or [OTHER], then press to enter.
6 Turn the volume knob to select [PN TYPE
REG], then press to enter.
■
To select “PN TYPE CHK”, play the
registered voice.
To select “PN TYPE DEL”, delete a voice
■
Select the name to register with reference
to 5 in <Calling a Number in the Phone
Book> (page 19).
If a voice tag has already been registered
for a name, “*” is displayed before the
name.
tag. Turn the volume knob to select “YES”,
then press to confirm.
7 “ENTER 1” is displayed. When a beep is
heard, say a voice tag within 2 seconds.
Continued to next page
English 23
8 “ENTER 2” is displayed. When a beep is
heard, say the same voice tag as that you
said in step 7 within 2 seconds.
“COMPLETE” is displayed.
Bluetooth Setup
1 Press and hold the volume knob to enter
Bluetooth mode.
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to make a
selection, then press to confirm.
9 Press the volume knob to return to step
5.
■
Set the voice tag for all the 5 categories. If
the voice tag is not registered for all the
categories, the Phone book may not be
recalled by voice command.
■
See table below for selection.
Repeat step 3 until the desired item is
■
selected/activated.
Press to return to the previous item.
■
4 Hold
to finish the procedure.
■
To exit Bluetooth mode, press SRC.
Item
PAIRING
Selectable setting (Preset: *)
DEVICE SEARCH Registers a Bluetooth device (pairing).
(For details, see page 22.)
PHONE SELECT Selects a cell-phone connection.
(For details, see page 23.)
AUDIO SELECT Selects a Bluetooth audio player connection. (For details, see page 23.)
S-DVC SELECT (For details, see page 22.)
DEVICE DELETE Cancel registration of the Bluetooth device.
1. Turn the volume knob to select the Bluetooth device, then press to confirm.
2. Turn the volume knob to select “YES”, then press to confirm.
SMS DOWNLOAD Download a short message. (For details, see page 26.)
VOICE TAG
PB NAME EDIT Registers voice for voice recognition and voice to select the Phone number category in Phone book.
(For details, see page 23.)
PN TYPE EDIT
DETAILED SET
PIN CODE EDIT Specify the PIN code required when registering this unit using the Bluetooth device. By default, “0000” is
specified.
1. Turn the volume knob to select the number.
■
To move to the next digit, press
¢
.
■
To delete the last digit, press
4
.
2. Press the volume knob to register a PIN code
AUTO ANSWER OFF: Does not answer the phone call automatically. ; 0: Automatically answers the phone call at once. ;
1 – 8 * –99: Automatically answers the phone call after lapse of 1 – 99 seconds.
BT HF/AUDIO
FRONT *: Outputs audio from the front-left and front-right speakers. ; ALL: Outputs audio from the all
speakers.
CALL BEEP
ON *: Outputs a beep from the speaker upon reception of an incoming call. ; OFF: Cancels.
BT F/W UPDATE Display the firmware version and update the firmware.
24 English
Item
MIC GAIN
Selectable setting (Preset: *)
–3 — 0 * — +3: Adjust the sensitivity of the built-in microphone for a telephone call. Adjust the voice of
caller. Setting to “+” increases the voice volume.
NR LEVEL
–3 — 0 * — +3: Reduce the noises generated by surrounding environment without changing the
built-in microphone volume. Adjust the voice of caller when it is not clear. Setting to “+” increases the noise
reduction.
EC LEVEL
–2 — 0 * — +2: Adjust the level of echo cancellation. Setting to “+” increases the echo cancel reduction.
■
[MIC GAIN], [NR LEVEL], [EC LEVEL] is selectable only for KCA-BT300.
About the Cell-Phone
■
Version:
KCA-BT300 : Bluetooth Standard Ver. 2.1
+ EDR
KCA-BT200 : Bluetooth Standard Ver. 1.2
Profile:
■
HFP (Hands Free Profile)
OPP (Object Push Profile)
PBAP (Phone book Access Profile)
SYNC (Synchronization Profile)
For the cell-phones verified for
compatibility, access the following URL:
■
The units supporting the Bluetooth
function have been certified for
conformity with the Bluetooth Standard
following the procedure prescribed
by Bluetooth SIG. However, it may be
impossible for such units to communicate
with your cell-phone depending on its
type.
English 25
SMS (Short Message Service)
Preparation : Only with the optional accessory KCA-BT300 or KCA-BT200 connected.
LIST
UPDATE
Press and hold to enter Bluetooth mode.
Display the SMS
Downloading the SMS
1 Press and hold the volume knob to enter
Bluetooth mode.
¤
To prevent car accidents, the driver should
not read the SMS while driving.
When a new message arrives
2 Turn the volume knob to select
[SETTINGS], then press to enter.
3 Turn the volume knob to select [SMS
DOWNLOAD], then press to enter.
4 Start downloading
“SMS RECEIVED” is displayed.
Displaying the SMS
1 Press and hold the volume knob to enter
Bluetooth mode.
■
During downloading: “DOWNLOADING”
is displayed.
After completion of downloading:
■
2 Turn the volume knob to select [SMS
INBOX], then press to enter.
3 Turn the volume knob to select a
message.
“COMPLETE” is displayed.
5 Hold
■
to finish the procedure.
To exit Bluetooth mode, press SRC.
The cell-phone must be able to transmit the
SMS using Bluetooth. Setting on the cell-
phone may be required. If the cell-phone
does not support SMS function, the SMS
download item in Function Control mode is
not displayed.
When the SMS is downloaded from the
cell-phone, the unopened messages in the
cell-phone are opened.
■
■
To switch between name, phone number
and message reception date, press DISP.
4 Press the volume knob to display the
text.
■
To scrolls the message, turn the volume
knob.
■
■
■
To return to the message list, press the
volume knob.
5 Hold
to finish the procedure.
The already-read and unread short
messages can be respectively downloaded
up to 75.
26 English
■
■
To exit Bluetooth mode, press SRC.
The unopened message is displayed at the
beginning of the list. Other messages are
displayed in the order of reception.
The SMS that has arrived when the cell-
phone is not linked with Bluetooth cannot
be displayed. Download the SMS.
The short message cannot be displayed
during downloading the SMS.
■
■
■
Unread messages are prefixed with an
asterisk (*).
Listening to the other external
components
Preparation : Make sure [ON1] or [ON2] is selected for [BUILT-IN AUX]. (page 7)
LIST
UPDATE
1 Press SRC to select “AUX”.
2 Turn on the external component and
Auxiliary input jack
start playing.
3 Turn the volume knob to adjust the
volume.
Portable audio device
(commercially available)
3.5 mm stereo mini plug
(commercially available)
English 27
Function settings
1 Press SRC to select a source other than “STANDBY”.
2 Press the volume knob to enter [FUNCTION] mode.
3 Turn the volume knob to select [AUDIO CONTROL] or [SETTINGS], then press to enter.
4 Turn the volume knob to make a selection, then press to confirm.
■
See table below for selection.
Repeat step 3 until the desired item is selected/activated.
Press to return to the previous item.
■
■
5 Hold
to finish the procedure.
[AUDIO CONTROL] : While listening to any source except in STANDBY state or Bluetooth mode.
Item
SUB-W LEVEL
BASS BOOST
SYSTEM Q
Selectable setting (Preset: *)
–15 — 0 * — +15: Adjusts the subwoofer output level.
B.BOOST LV1 */ B.BOOST LV2: Selects your preferred bass boost level. ; OFF: Cancels.
NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ GAME: Selects a preset sound mode suitable to the
music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS ADJUST
BASS CTR FRQ 60/ 80/ 100 */ 200: Selects the center frequency.
BASS LEVEL
–8 — 0 * — +8: Adjusts the level.
BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF *: Cancels.
MID ADJUST
MID CTR FRQ
MID LEVEL
0.5K/1.0K */ 1.5K/ 2.5K: Selects the center frequency.
–8 — 0 * — +8: Adjusts the level.
MID Q FACTOR 0.75/ 1.00 */ 1.25: Adjusts the quality factor.
TRE ADJUST
TRE CTR FRQ
TRE LEVEL
BALANCE
FADER
10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.
–8 — 0 * — +8: Adjusts the level.
L15 — 0 * — R15: Adjusts the left and right speaker output balance.
R15 — 0 * — F15: Adjusts the rear and front speaker output balance.
SUBWOOFER SET ON *: Turns on the subwoofer output. ; OFF: Cancels.
DETAILED SET
LPF
SUBWOOFER
THROUGH *: All signals are sent to the subwoofer. ; 85/120/160 (HZ): Frequencies higher than the specified
value are cut off.
SUB-W PHASE REVERSE (180°)/ NORMAL (0°) *: Selects the phase angle of the subwoofer output to be in line with the
speaker output for optimum performance. (Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
SUPREME SET ON *: Creates realistic sound by interpolating the high-frequency components that are lost in AAC/ MP3/
WMA audio compression. ; OFF: Cancels. (Selectable only when playback an AAC/ MP3/ WMA disc or a USB
device, except iPod.)
28 English
Item
Selectable setting (Preset: *)
VOLUME OFFSET –8 — 0 * — +8 (for AUX) ; –8 — 0 * (for other sources): Presets the volume adjustment level of each
source. The volume level will automatically increase or decrease when you change the source. (Before making
an adjustment, select the source you want to adjust.)
■
■
[SUB-W LEVEL/ SUBWOOFER SET/ LPF SUBWOOFER/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W].
(page 7)
[SUB-W LEVEL/ LPF SUBWOOFER/ SUB-W PHASE] is selectable only if [SUBWOOFER SET] is set to [ON].
[SETTINGS]
Item
AUX NAME SET
Selectable setting (Preset: *)
AUX */ DVD/ PORTABLE/ GAME/ VIDEO/ TV: Selects the desired name for the connected component.
(Selectable only if “AUX” is selected as the source.)
CLOCK
CLOCK ADJUST (For details, see page 6.)
TIME SYNC
DISPLAY
ON *: Synchronizes the DAB station time data and the unit’s clock. ; OFF: Cancels.
DIMMER SET ON: Dims the display illumination. ; OFF *: Cancels.
TEXT SCROLL AUTO/ ONCE: Selects to scroll the display information automatically, or scroll only once. ; OFF *: Cancels.
BT DVC STATUS You can display the connection status, signal strength, and battery level of cell-phone.
HF-CON: Connection status for cell-phone. ; AD-CON: Connection status for BT Audio. ;
BATT: Battery level of cell-phone. ; SIGNAL: Signal strength of cell-phone.
DAB SET
PRIORITY/ ASW SELECT/ DAB LIST UPDT: Selectable only if any source other than DAB source is selected. (For
details, see page 9.)
TUNER SET
NEWS SET/ AF SET/ REGIONAL/ AUTO TP SEEK: Selectable only if any source other than tuner source is
selected. (For details, see page 11.)
■
[BT DVC STATUS] is selectable only for KCA-BT300 or KCA-BT200 connected.
[PRIORITY] is selectable only when the source is “TUNER”.
■
English 29
Installation/connection
■
Part list:
Insulate unconnected wires with vinyl tape
A Faceplate ...................................................................(×1)
B Escutcheon..............................................................(×1)
C Mounting sleeve...................................................(×1)
D Wiring harness.......................................................(×1)
E Removal tool.......................................................... (×2)
F DAB antenna film *1 ............................................(×1)
G DAB antenna amplifier *1.................................(×1)
H Cord clamper *1 .................................................... (×3)
I Cleaner *1...................................................................(×1)
• *1 KDC-DAB41U only
or other similar material. To prevent a short
circuit, do not remove the caps on the ends
of the unconnected wires or the terminals.
Be sure to ground this unit to the car’s
chassis again after installation.
If the power is not turned ON (“PROTECT”
is displayed), the speaker wire may have a
short-circuit or touched the chassis of the
vehicle and the protection function may
have been activated. Therefore, the speaker
wire should be checked.
■
■
Basic procedure
Caution
1 Remove the key from the ignition switch,
then disconnect the · terminal of the
car battery.
2 Install the DAB antenna.
\ <Installation the DAB antenna
(KDC-DAB41U only)> (page 34)
3 Make proper input and output wire
connections.
■
If your car’s ignition does not have an ACC
position, connect the ignition wires to a
power source that can be turned on and
off with the ignition key. If you connect
the ignition wire to a power source with
a constant voltage supply, as with battery
wires, the battery may die.
■
■
\ <Wiring connection> (page 32)
4 Install the unit to your car.
\ <Installing the unit> (page 33)
5 Reconnect the · terminal of the car
battery.
Install this unit in the console of your
vehicle. Make sure the faceplate will not hit
the lid of the console (if any) when closing
and opening.
After the unit is installed, check whether the
brake lamps, blinkers, wipers, etc. on the car
are working properly.
6 Reset the unit. (page 3)
■
■
Mount the unit so that the mounting angle
is 30° or less.
If the fuse blows, first make sure the wires
are not touching to cause a short circuit,
then replace the old fuse with one that has
the same rating.
Connect the speaker wires correctly to the
terminals to which they correspond. The
unit may be damaged or fail to work if you
share the · wires or ground them to any
metal part in the car.
Warning
■
The unit can only be installed in a car with a
12 V DC power supply, negative ground.
If you connect the ignition wire (red) and
■
the battery wire (yellow) to the car chassis
(ground), you may cause a short circuit,
that in turn may start a fire. Always connect
those wires to the power source running
through the fuse box.
■
■
Disconnect the battery’s negative terminal
and make all electrical connections before
installing the unit.
30 English
■
When only two speakers are being
connected to the system, connect the
connectors either to both the front output
terminals or to both the rear output
terminals (do not mix front and rear).
Mounting and wiring this product requires
skills and experience. For safety’s sake, leave
this work to professionals.
■
If you experience problems during
installation, consult your Kenwood dealer.
About Bluetooth unit (Optional)
■
This unit supports KCA-BT300 or KCA-BT200.
Plugging a KCA-BT300/ KCA-BT200 into this
unit will enable BT audio.
■
– Selecting Bluetooth Audio source
Press SRC to select the “BT AUDIO EXT”.
– To pause/resumes playback, press number
button 6 (38).
– To select track, press 4 or ¢.
Set the Type Switch on KCA-BT300/ KCA-
BT200 as follows:
■
1: OFF, 2: OFF, 3: OFF
¤ CAUTION
Install this unit in the console of your
vehicle.
Do not touch the metal part of this unit
during and shortly after the use of the
unit. Metal part such as the heat sink and
enclosure become hot.
English 31
Wiring connection
FM/AM antenna
input (JASO)
USB connector
Antenna Cord
AUX input (Stereo)
Use the mini-plug (3.5 mm ø) cable which
is stereo type and does not have any
resistance.
Rear output/ Sub
Woofer output
To Kenwood disc changer/ External
optional accessory
(To connect these leads, refer to the
relevant instruction manuals.)
switchable (“SWITCH
PREOUT” page 7)
DAB antenna input
(SMB) (“DAB ANT
POWER” page 7)
L
R
Fuse (10A)
Wiring
harness D
If no connections are made, do not let the wire come out from the
tab.
Connect to the terminal that is grounded when
Brown
either the telephone rings or during conversation.
To connect the Kenwood navigation system, consult
your navigation manual.
MUTE
(Mute control wire)
Light Blue/Yellow
To use the steering wheel remote control feature,
you need to an exclusive remote adapter (not
supplied) matches your car is required.
REMOTE CONT
(Steering remote
control wire)
STEERING WHEEL
REMOTE INPUT
Connect either to the power control terminal when
using the optional power amplifier, or to the antenna
control terminal in the vehicle.
Blue/White
P.CONT
(Power control/
Antenna control wire)
ANT. CONT
Connecting the ISO connectors on some VW/Audi
or Opel (Vauxhall) automobiles
You may need to modify the wiring of the supplied
wiring harness as illustrated below.
Yellow (Battery wire)
Red (Ignition wire)
Red (A–7 Pin)
Yellow (A–4 Pin)
Red (A–7 Pin)
Vehicle
Red (Ignition wire)
Unit
Connector A
Connector B
8
7
6
5
4
3
2
1
Yellow (Battery wire)
Yellow (A–4 Pin)
8
7
6
5
4
3
2
1
Default wiring
Pin
A4
A5
A7
A8
Color and function
Pin
B1 / B2 Purple
B3 / B4 Gray
B5 / B6 White
B7 / B8 Green
Color and function
Yellow
Battery
ª
/ Purple/black
·
Rear speaker (right)
Front speaker (right)
Front speaker (left)
Rear speaker (left)
Blue/White
Red
Power control
Ignition (ACC)
ª
/ Gray/black
/ White/black
·
ª
ª
·
·
Black
Earth (ground) connection
/ Green/black
32 English
Installing the unit
1
3
Connect the wiring harness to the
unit. Other wiring connection has
been completed earlier. (page 32)
C
2
1
B
D
A
2
Before attaching, make
sure the direction of the
escutcheon is correct.
(Wider hooks on the
bottom side.)
2
1
Dashboard of
your car
3
C
4
Bend the appropriate tabs
to hold the mounting sleeve
firmly in place.
5
B
A
Removing the unit
1 Detach the faceplate A.
E
2 Engage the catch pin on the removal
tools E into the holes on both sides of
the escutcheon B, then pull it out.
3 Insert the removal tools E deeply into
the slots on each side, then follow the
arrows instructions as shown on the
right.
B
C
3
1
A
2
E
English 33
Installation the DAB antenna (KDC-DAB41U only)
CAUTION
This film antenna is exclusively for use inside
Installation overview
■
the vehicle.
Do not install at the following locations:
■
DAB antenna F/ G
– Where it may block driver’s view
– Where it may obstruct operation of safety
devices such as air bags
– On movable glass surface such as rear
hatch
Signal strength will decrease at the
■
following locations:
– On IR reflecting glass or where covered
with mirror type glass film
– Where it overlaps with genuine radio
antenna (pattern)
– Where it overlaps with window heating
wires
– At side of vehicle (e.g. door, front quarter
window)
– On rear window
– When glass that blocks radio signals (e.g.
IR reflecting glass, thermal insulation glass)
is used
– Reception may decrease due to noise
when windshield wiper, air conditioner, or
motor is turned on.
– Reception may decrease depending on
the direction of the broadcast station with
respect to the vehicle (antenna).
Be sure to check the installation location
of film antenna F before installing. Film
antenna cannot be re-pasted.
Thoroughly wipe oil and dirt from the
pasting surface with the included cleaner
I.
Antenna cable
(3.5 m)
■
■
■
The antenna should be installed on the
passenger side for safety.
Use cord clamper H to secure the antenna
to the pillar at several locations.
The direction of the antenna film F
changes depending on whether the film
antenna F is installed on the right side or
left side.
Separate the antenna film F from the
ceramic line (black part) at the top of the
front glass by 150 mm.
Also, place it about 70 mm inside the
ceramic line at the side end of the front
glass. (where the earth sheet of the amplifier
can be pasted on the metal part of the front
pillar)
Separate from other antennas by at least
100 mm.
Do not paste the amplifier G on the
ceramic line (black part) around the
front glass. Because there is not enough
adhesion.
■
■
■
■
■
■
Do not bend or damage the film antenna F.
Warm the pasting surface by turning on the
■
heater for example, before applying.
It may not be possible to install on some
■
type of vehicle.
Check the cable routing of the film antenna
■
F and amplifier G before pasting.
34 English
Determining the antenna installation location
When installing the antenna on the left side
When installing the antenna on the right
side
Front pillar
Amplifier G
Earth sheet
150 mm
150 mm
Earth sheet
70 mm *1
Antenna film F
70 mm *1
Antenna film F
Amplifier G
• *1 Where the earth sheet of Amplifier G can be pasted on the metal part of the front pillar.
Antenna Installation
1 Check the installation location.
2 Wipe the area where antenna film F,
amplifier unit G, and earth sheet are
pasted with the included cleaner I.
The coating on the metal surface need not
be removed.
■
Wait until the glass surface is completely
dry before pasting.
If the glass surface is cold, such as during
winter, warm it with defroster or dryer.
3 Remove the separator (tag I) of antenna
film F horizontally and paste the
antenna on the front glass.
5 After pasting, rub the element in the
glass surface in the direction of the arrow
shown in the figure to bond it.
■
6 Remove the application film (tag III).
■
Remove the separator gently.
Do not touch the pasting surface
■
Do not touch the feeder terminal of the
element. Also, do not apply any glass
cleaner.
■
(adhesive side) of the antenna film F.
4 Remove the separator (tag II) of antenna
film F vertically and paste the antenna
gently while applying pressure.
Feeder terminal
Continued to next page
English 35
9 Wire the antenna cables.
7 Match the protrusion of the amplifier G
with the 5 on the antenna film F and
paste.
■
Use cord clamper H to secure the
antenna to the pillar at several locations.
Notes
■
Do not touch the feeder terminal or the
Take the following precautions when
passing the antenna cable inside the front
pillar where the air bag is installed.
pasting surface (adhesive side) of the
amplifier.
When installing the antenna on the right
side
–
Install the amplifier part of the antenna
cable in front or above the air bag so
that the antenna and the air bag do not
interfere.
Match the protrusion with 5
Earth sheet
Amplifier G
Antenna film
F
Amplifier G
Air bag
When installing the antenna on the left
side
Antenna film F
Amplifier G
Front pillar
–
The front pillar cover is secured with
Earth sheet
a special clip which may need to be
replaced when the front pillar cover is
removed.
Contact your vehicle dealer for details
on replacing the front pillar cover and
availability of replacement parts.
Match the protrusion with 5
8 Remove the film covering the earth sheet
and paste the earth sheet on the metal
part of the vehicle.
Provide sufficient leeway for the earth
sheet so that it does not interfere with the
interior parts (front pillar cover).
Interior part
Clip
Also take care that the interior parts do not
interfere with the amplifier G.
Front glass
Amplifier G
Select the DAB antenna power
Set ”INITIAL SET” > “DAB ANT POWER” to “ON”
Front pillar
in STANDBY mode. (page 7)
Interior part
Earth sheet
36 English
Troubleshooting
Symptom
Remedy/Cause
Adjust the volume to the optimum level. / Check the cords and connections.
“PROTECT” appears and no operations can Check to be sure the terminals of the speaker leads are covered with insulating tape
Sound cannot be heard.
be done.
properly, then reset the unit. If “PROTECT” does not disappear, consult your nearest
service center.
Reset the unit.
The unit does not work at all.
Radio reception is poor. / Static noise while Connect the antenna firmly. / Pull the antenna out all the way.
listening to the radio.
“IN” flashes.
The CD player is not operating properly. Reinsert the disc properly. If the condition did
not improve, turn off the unit and consult your nearest service center.
Insert a finalized CD-R/CD-RW (finalize with the component which you used for
recording).
CD-R/CD-RW cannot be played back and
tracks cannot be skipped.
Disc sound is sometimes interrupted.
Stop playback while driving on rough roads. / Change the disc. / Check the cords and
connections.
“NA FILE” appears.
“NO DISC” appears.
“TOC ERROR” appears.
The unit is playing an unsupported audio file.
Insert a playable disc into the loading slot.
The CD is quite dirty. / The CD is upside-down. / The CD is scratched a lot. Try another
disc instead.
“ERROR 77” or “ERROR 99” appears.
The unit is malfunctioning for some reason. Press the reset button on the unit. If the
“ERROR 77”/ “ERROR 99” code does not disappear, consult your nearest service center.
A copy-protected file is played.
“COPY PRO” appears.
“READ ERROR” appears.
Copy the files and folders for the USB device again. If the error message is still
displayed, initialize the USB device or use other USB devices.
No USB device is connected. Connect a USB device, and change the source to USB
again.
“NO DEVICE” appears.
“NO MUSIC” or “ERROR 15” appears.
The connected USB device contains no playable audio file. / Media which does not
have data playable with the unit was played.
“NA DEVICE” appears.
“USB ERROR” appears.
Connect a supported USB device, and check the connections.
Remove the USB device, turn the unit off, then turn it on again. If the unit still showing
the same display, try to connect another USB device.
Reconnect the iPod. / Reset the iPod.
“iPod ERROR” appears.
Noise is generated.
Skip to another track or change the disc.
Tracks cannot play back as you have intended Playback order is determined when files are recorded.
them to play.
“READING” keeps flashing.
Elapsed playing time is not correct.
Longer readout time is required. Do not use too many hierarchies and folders.
This is caused by how the tracks are recorded.
The number of songs contained in “SONGS” Podcast files are not counted in this unit as this unit does not support the playback of
category of this unit is different from that
contained in “SONGS” category of iPod.
podcast files.
Continued to next page
English 37
Symptom
Correct characters are not displayed (e.g.
album name).
Remedy/Cause
This unit can only display letters (upper case), numbers, and a limited number of
symbols.
Bluetooth
Symptom
Remedy/Cause
The hands-free talk volume is low.
The hands-free talk volume can be adjusted independently. Adjust it during hands-
free talk. [MIC GAIN], [NR LEVEL] and [EC LEVEL] of <Bluetooth Setup> (page 24).
No beep is heard at reception of an incoming No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of
call.
<Bluetooth Setup> (page 24) is set ON.
■
Voice is not recognized.
The vehicle window is open. If the surrounding noise is large, voice cannot be
recognized properly. Close the vehicle windows to reduce noise.
Small voice. If voice is too small, it cannot be recognized properly. Speak into the
■
microphone a little more loudly and naturally.
The person uttering the voice tag is not the one who registered the it. Only the
■
voice of the person who registered the voice tag can be recognized.
The calling party does not notify a caller ID. / There is no phone number data.
There is no outgoing call list. / There is no incoming call list. / There is no missed call
list. / There is no phone book list.
“NO NUMBER” appears.
“NO DATA” appears.
“NO ENTRY” appears.
“HF DISCONCT” appears.
“HF ERROR 07” appears.
The cell-phone has not been registered (pairing).
The unit cannot communicate with the cell-phone.
The memory cannot be accessed. Turn off the power and on again. If this message still
appears, press the reset button on the control unit.
The unit cannot communicate with the cell-phone. Turn off the power and on again. If
this message still appears, press the reset button on the control unit.
The Bluetooth device cannot be detected.
“HF ERROR 68” appears.
“UNKNOWN” appears.
“DEVICE FULL” appears.
5 Bluetooth device have already been registered. No more Bluetooth device cannot
be registered.
“PIN CODE NG” appears.
“CONNECT NG” appears.
“PAIRING NG” appears.
“NO MARCHING” appears.
The PIN code is wrong.
The unit cannot be connected to the device.
Pairing error.
The voice tag is wrong. Voice cannot be recognized because of an unregistered voice
tag, etc.
“TOO SOFT” appears.
Voice is too small and cannot be recognized.
Voice is too large to be recognized.
The word or utterance is too long to be recognized.
Data is not contained in the phone book.
“TOO LOUD” appears.
“TOO LONG” appears.
“NO PHONEBOOK” appears.
“NO MESSAGE” appears.
“NO RECORD” appears.
“MEMORY FULL” appears.
No short message in In Box.
The voice tag is not registered in the phone book.
The number of voice tags reaches the maximum number to be registered in the phone
book.
“NO VOICE” appears.
No call.
38 English
Symptom
Remedy/Cause
■
The sound from the Bluetooth audio player is Another Bluetooth device is affecting the Bluetooth communication. Turn off
discontinuous.
another Bluetooth device. Move another Bluetooth device away from this unit.
Another Bluetooth device or profile is used for communication. The downloading of
the Phone book or the SMS disconnects the sound.
■
DAB
Symptom
Remedy/Cause
“DAB ANT ERROR” appears.
The antenna has a short-circuit and the protective circuit has activated. Check the DAB
antenna. If a passive antenna without a booster is used, set DAB ANT POWER "OFF".
(page 7)
DAB reception is poor.
If an antenna included with KDC-DAB41U is used, set DAB ANT POWER "ON". (page 7)
English 39
Specifications
DAB tuner section
USB interface
Frequency range:
USB standard: USB1.1/ 2.0 (Full speed)
Maximum supply current: 500 mA
File system: FAT16/ 32
L Band: 1452.960 MHz — 1490.624 MHz
Band III: 174.928 MHz — 239.200 MHz
Sensitivity: -100 dBm
AAC decode: AAC-LC “.m4a” files
MP3 decode: Compliant with MPEG-1/2 Audio
Layer-3
WMA decode: Compliant with Windows Media
Audio
Signal-to-Noise ratio: 80 dB
FM tuner section
Frequency range (50 kHz space):
87.5 MHz — 108.0 MHz
Usable sensitivity (S/N= 26 dB): 1 μV/ 75 Ω
Quieting sensitivity (DIN S/N = 46 dB): 2.5 μV/75 Ω
Frequency response ( 3 dB): 30 Hz — 15 kHz
Signal-to-Noise ratio (MONO): 63 dB
Stereo separation (1 kHz): 40 dB
Audio section
Maximum output power: 50 W × 4
Output power (DIN 45324, +B=14.4V): 30 W × 4
Speaker impedance: 4 Ω — 8 Ω
Tone action:
Bass: 100 Hz 8 dB
Middle: 1 kHz 8 dB
Treble: 12.5 kHz 8 dB
MW tuner section
Frequency range (9 kHz space): 531 kHz – 1,611 kHz
Usable sensitivity (S/N = 20 dB): 36 μV
Preout level / load (CD): 2,500 mV/ 10 kΩ
Preout impedance: ≤ 600 Ω
LW tuner section
Frequency range: 153 kHz – 279 kHz
Usable sensitivity (S/N = 20 dB): 57 μV
Auxiliary input section
Frequency response ( 3 dB): 20 Hz — 20 kHz
Input maximum voltage: 1,200 mV
Input impedance: 10 kΩ
CD player section
Laser diode: GaAIAs
Digital filter (D/A): 8 Times Over Sampling
D/A converter: 24 Bit
Spindle speed: 500 rpm — 200 rpm (CLV)
Wow & Flutter: Below Measurable Limit
Frequency response ( 1 dB): 20 Hz — 20 kHz
Total harmonic distortion (1 kHz): 0.01 %
Signal-to-Noise ratio (1 kHz): 105 dB
Dynamic range: 93 dB
AAC decode: AAC-LC “.m4a” files
MP3 decode: Compliant with MPEG-1/2 Audio
Layer-3
DAB Antenna Connector
Connector type: SMB
Output Voltage (11 V — 16 V): 14.4 V
Maximum Current: <100 mA
General
Operating voltage (11 V — 16 V allowable): 14.4 V
Maximum current consumption: 10 A
Installation size (W × H × D):
182 mm × 53 mm × 159 mm
Weight: 1.2 kg
WMA decode: Compliant with Windows Media
Audio
Subject to change without notice.
40 English
Information on Disposal of Old
Electrical and Electronic Equipment
and Batteries (applicable for
EU countries that have adopted
separate waste collection systems)
Products and batteries with the
symbol (crossed-out wheeled bin)
cannot be disposed as household
waste.
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo,
192-8525 Japan
EU Representative’s:
Old electrical and electronic
equipment and batteries should
be recycled at a facility capable
of handling these items and their
waste byproducts.
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN,
The Netherlands
Contact your local authority for
details in locating a recycle facility
nearest to you.
Proper recycling and waste disposal
will help conserve resources whilst
preventing detrimental effects on
our health and the environment.
Notice: The sign “Pb” below the
symbol for batteries
indicates that this battery
contains lead.
■
The “AAC” logo is a trademark of Dolby
Laboratories.
“Made for iPod” and “Made for iPhone”
■
This Product is not installed by the
mean that an electronic accessory has
been designed to connect specifically
to iPod or iPhone, respectively, and has
been certified by the developer to meet
Apple performance standards. Apple is not
responsible for the operation of this device
or its compliance with safety and regulatory
standards. Please note that the use of this
accessory with iPod or iPhone may affect
wireless performance.
manufacturer of a vehicle on the production
line, nor by the professional importer of a
vehicle into an EU Member State.
The marking of products using
lasers
CLASS 1
LASER PRODUCT
■
iPhone, iPod, iPod classic, iPod nano, and
iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries.
The label is attached to the chassis/case and
says that the component uses laser beams
that have been classified as Class 1.
This symbol mark indicates
that Kenwood manufactured
this product so as to decrease
harmful influence on the
environment.
It means that the unit is utilizing laser beams
that are of a weaker class. There is no danger
of hazardous radiation outside the unit.
English 41
|