|
Bluetooth EZ-Extender®
Manual
Revision 1.0, October 2009
Part Number
82-000218-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106
a
Regulatory Compliance
The Bluetooth EZ-Extender is designed to be used solely in a laboratory
environment. The board is not intended for use as a consumer end prod-
uct or as a portion of a consumer end product. The board is an open
system design, which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The Bluetooth EZ-Extender is currently being processed for certification
that it complies with the essential requirements of the European EMC
directive 89/336/EEC amended by 93/68/EEC and therefore carries the
“CE” mark.
The EZ-Extender system contains ESD (electrostatic discharge) sensitive
devices. Electrostatic charges readily accumulate on the human body and
equipment and can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges. Proper ESD precau-
tions are recommended to avoid performance degradation or loss of func-
tionality. Store unused EZ-Extender boards in the protective shipping
package.
CONTENTS
PREFACE
Product Overview ............................................................................ x
Purpose of This Manual .................................................................. xi
Intended Audience .......................................................................... xi
Manual Contents ............................................................................ xi
What’s New in This Manual ........................................................... xii
Technical or Customer Support ...................................................... xii
Supported Products ....................................................................... xiii
Product Information ..................................................................... xiii
Analog Devices Web Site .......................................................... xiv
Package Contents .......................................................................... 1-2
Bluetooth EZ-Extender Default Configuration .............................. 1-3
Bluetooth EZ-Extender Setup ........................................................ 1-4
Flash Memory Interface ................................................................. 1-4
Bluetooth EZ-Extender Manual
v
CONTENTS
UART Interface ............................................................................ 1-4
Bluetooth Module ........................................................................ 1-5
System Architecture ...................................................................... 2-2
Configuration Switch ................................................................... 2-3
Jumpers ........................................................................................ 2-5
TWI Flash Address Configuration Jumper (JP1) ...................... 2-6
TWI Flash Write Protect Jumper (JP2) .................................... 2-6
Soft Reset Configuration Jumpers (JP3–4) ............................... 2-6
Bluetooth Module Default Configuration Jumper (JP5) ........... 2-6
UART Receive Data Jumper (JP6) ........................................... 2-6
Power LED ................................................................................... 2-7
Connectors ................................................................................... 2-8
STAMP UART Connector (J1) ............................................... 2-9
Expansion Interface II Connector (J3) ..................................... 2-9
Expansion Interface II Connector (J5) ................................... 2-10
Expansion Interface II Connector (P2) .................................. 2-10
Expansion Interface II Connector (P4) .................................. 2-11
USB Connector (P3) ............................................................. 2-11
vi
Bluetooth EZ-Extender Manual
Title Page .................................................................................... B-1
LS Connector .............................................................................. B-3
PPI Connector ............................................................................. B-4
INDEX
Bluetooth EZ-Extender Manual
vii
CONTENTS
viii
Bluetooth EZ-Extender Manual
PREFACE
®
Thank you for purchasing the Bluetooth EZ-Extender , Analog
Devices, Inc. daughter board to a Blackfin evaluation system with the new
expansion interface II (such as the ADSP-BF518F EZ-Board™) or the
®
older STAMP interface (such as the ADSP-BF537 EZ-KIT Lite ).
Blackfin processors are embedded processors that support a Media
Instruction Set Computing (MISC) architecture. This architecture is the
natural merging of RISC, media functions, and digital signal processing
characteristics towards delivering signal processing performance in a
microprocessor-like environment.
The Bluetooth EZ-Extender is designed to be used in conjunction with an
EZ-KIT Lite or an EZ-Board running the open source Linux operating
system (OS). For more information about running Linux OS on a Black-
Bluetooth EZ-Extender Manual
ix
Product Overview
Product Overview
The Bluetooth EZ-Extender is a separately sold daughter board that plugs
onto an EZ-KIT Lite supporting the STAMP interface or
an EZ-Board/EZ-Kit Lite supporting the expansion interface II connec-
tor. The extender board isolates the low-level configuration and
communication tasks of integrating Bluetooth and radio frequency (RF)
wireless technologies in your Blackfin board designs.
The board extends the capabilities of the Blackfin evaluation system by
providing a connection to the Bluegiga WT12 Bluetooth module.
The board features:
• Bluegiga WT12 Bluetooth module
D Bluetooth radio antenna
D Fully implemented protocol stack
D HCI and iWRAP firmware
• USB interface
D Full speed USB interface for communicating with other
compatible digital devices. The WT12 module acts as
a USB peripheral.
• UART interface
D Standard UART interface for communicating with other
serial devices
D Supports hardware flow control
• Expansion interface
D Allows other EZ-Extenders to be stacked
x
Bluetooth EZ-Extender Manual
Preface
All of the power necessary to operate the extender is derived from the mat-
ing EZ-KIT Lite/EZ-Board. Before using any of the interfaces, follow the
setup procedure in “Bluetooth EZ-Extender Setup” on page 1-4.
Purpose of This Manual
The Bluetooth EZ-Extender Manual describes operation and configuration
of the extender board components. A schematic and a bill of materials are
provided for reference.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set. Programmers who are unfamiliar with Analog Devices
processors can use this manual, but should supplement it with other texts
(such as the Processor Hardware Reference and Processor Instruction Set Ref-
erence) that describe your target architecture.
Manual Contents
• Chapter 1, “Using Bluetooth EZ-Extender” on page 1-1
Provides basic board information.
• Chapter 2, “Bluetooth EZ-Extender Hardware Reference” on
page 2-1
Provides information about the hardware aspects of the board.
Bluetooth EZ-Extender Manual
xi
What’s New in This Manual
• Appendix A, “Bluetooth EZ-Extender Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the board.
• Appendix B, “Bluetooth EZ-Extender Schematic” on page B-1
Provides the resources to allow board-level debugging or to use as
a reference guide.
What’s New in This Manual
This is the first revision of the Bluetooth EZ-Extender Manual.
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
• E-mail tools questions to
• E-mail processor questions to
• Phone questions to 1-800-ANALOGD
xii
Bluetooth EZ-Extender Manual
Preface
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Products
The Bluetooth EZ-Extender is designed as an extender board to the
ADSP-BF518F and ADSP-BF526 EZ-Board evaluation systems. The
extender also is compatible with the Blackfin evaluation systems featuring
the STAMP interface, such as the ADSP-BF548 and ADSP-BF527
EZ-KIT Lites.
Product Information
Product information can be obtained from the Analog Devices Web site
and a technical library CD.
Bluetooth EZ-Extender Manual
xiii
Product Information
Analog Devices Web Site
about a broad range of products—analog integrated circuits, amplifiers,
converters, and digital signal processors.
To access a complete technical library for each processor family, go to
http://www.analog.com/processors/technical_library. The manuals
selection opens a list of current manuals related to the product as well as a
link to the previous revisions of the manuals. When locating your manual
title, note a possible errata check mark next to the title that leads to the
current correction report against the manual.
that allows customization of a Web page to display only the latest infor-
mation about products you are interested in. You can choose to receive
weekly e-mail notifications containing updates to the Web pages that meet
your interests, including documentation errata against all manuals.
MyAnalog.com provides access to books, application notes, data sheets,
code examples, and more.
Visit MyAnalog.com to sign up. If you are a registered user, just log on.
Your user name is your e-mail address.
Technical Library CD
The technical library CD contains seminar materials, product highlights, a
selection guide, and documentation files of processor manuals, Visu-
alDSP++ software manuals, and hardware tools manuals for the following
processor families: Blackfin, SHARC, TigerSHARC, ADSP-218x, and
ADSP-219x.
To order the technical library CD, go to http://www.analog.com/proces-
sors/technical_library, navigate to the manuals page for your
processor, click the request CD check mark, and fill out the order form.
xiv
Bluetooth EZ-Extender Manual
Preface
Data sheets, which can be downloaded from the Analog Devices Web site,
change rapidly, and therefore are not included on the technical library
CD. Technical manuals change periodically. Check the Web site for the
latest manual revisions and associated documentation errata.
Related Documents
For information on product related development software, see the follow-
ing publications.
Table 1. Related Processor Publications
Title
Description
Processor Data Sheet
General functional description, pinout, and timing
of the processor.
Processor Hardware Reference
Description of the internal processor architecture
and all register functions.
Processor Programming Reference
Description of all allowed processor assembly
instructions.
Table 2. Related Tools Publications
Title
Description
EZ-Board Evaluation System Manual
EZ-KIT Lite Evaluation System Manual
Description of the hardware capabilities of the eval-
uation system.
Bluetooth EZ-Extender Manual
xv
Notation Conventions
Notation Conventions
Text conventions used in this manual are identified and described as fol-
lows. Additional conventions, which apply only to specific chapters, may
appear throughout this document.
Example
Description
{this | that}
Alternative required items in syntax descriptions appear within curly
brackets and separated by vertical bars; read the example as thisor
that. One or the other is required.
[this | that]
[this,…]
Optional items in syntax descriptions appear within brackets and sepa-
rated by vertical bars; read the example as an optional this or that.
Optional item lists in syntax descriptions appear within brackets
delimited by commas and terminated with an ellipse; read the example
as an optional comma-separated list of this.
.SECTION
Commands, directives, keywords, and feature names are in text with
letter gothicfont.
filename
Non-keyword placeholders appear in text with italic style format.
Note: For correct operation, ...
A Note provides supplementary information on a related topic. In the
online version of this book, the word Note appears instead of this
symbol.
L
a
Caution: Incorrect device operation may result if ...
Caution: Device damage may result if ...
A Caution identifies conditions or inappropriate usage of the product
that could lead to undesirable results or product damage. In the online
version of this book, the word Caution appears instead of this symbol.
Warning: Injury to device users may result if ...
A Warning identifies conditions or inappropriate usage of the product
that could lead to conditions that are potentially hazardous for the
devices users. In the online version of this book, the word Warning
appears instead of this symbol.
[
xvi
Bluetooth EZ-Extender Manual
1 USING BLUETOOTH
EZ-EXTENDER
This chapter describes the Bluetooth EZ-Extender’s package contents,
configuration, installation procedure, and interfaces.
The information is presented in the following order.
Describes the product’s package contents.
Describes the board’s default configuration.
Provides the board’s setup procedure.
Describes the on-board flash memory interface.
Describes the on-board UART interface.
• “Bluetooth Module” on page 1-5
Describes the on-board Bluetooth interface.
• “USB Interface” on page 1-5
Describes the on-board USB interface.
Bluetooth EZ-Extender Manual
1-1
• “Expansion Interface” on page 1-6
Describes the board’s expansion interface.
Describes the example programs installed with the board’s
software.
For more information about the mating Blackfin processor, see documents
referred to as “Related Documents”.
Package Contents
Your Bluetooth EZ-Extender package contains one item: the Bluetooth
EZ-Extender board. If the board is missing, contact the vendor where you
purchased your Bluetooth EZ-Extender or contact Analog Devices, Inc.
1-2
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Default
Configuration
The EZ-Extender system contains ESD (electrostatic discharge) sensitive
devices. Electrostatic charges readily accumulate on the human body and
equipment and can discharge without detection. Permanent damage may
occur on devices subjected to high-energy discharges. Proper ESD precau-
tions are recommended to avoid performance degradation or loss of func-
tionality. Store unused EZ-Extender boards in the protective shipping
package.
When removing the Bluetooth EZ-Extender from the package, handle the
board carefully to avoid the discharge of static electricity, which can dam-
age some components (see Figure 1-1).
Figure 1-1. Default EZ-Extender Hardware Setup
Bluetooth EZ-Extender Manual
1-3
Figure 1-1 shows the default jumper and switch settings, connector loca-
tions, and LED used in installation. Confirm that your board is in the
default configuration before using the board.
Bluetooth EZ-Extender Setup
It is important to set up all components of the system containing the Blue-
tooth EZ-Extender and then apply power to the system. Power on your
system after the Bluetooth EZ-Extender has been connected to the
EZ-Board or EZ-KIT Lite. Do not install or remove the Bluetooth
EZ-Extender when power is applied to the EZ-Board or EZ-KIT Lite.
2
The Bluetooth EZ-Extender is equipped with an I C serial flash memory
chip for data configuration. Flash memory is programmed by the factory.
For more information, refer to “TWI Flash Address Configuration Jumper
(JP1)” on page 2-6 and “TWI Flash Write Protect Jumper (JP2)” on
page 2-6.
The UART interface is used for general communication between the pro-
cessor and WT12 Bluegiga Bluetooth module. The interface has a max
baud rate of 3.0 Mbaud. Flow control is supported via SW1. Refer to
“Configuration Switch” on page 2-3 for more information.
1-4
Bluetooth EZ-Extender Manual
Bluetooth Module
The Bluegiga WT12 module is a next-generation, class 2, Bluetooth 2.0
plus EDR module. The WT12 is a highly integrated and sophisticated
Bluetooth module, containing all of the necessary elements from Blue-
tooth radio antenna to a fully implemented protocol stack. Therefore, the
WT12 module provides an ideal solution for developers who want to inte-
grate Bluetooth wireless technology into their design with limited
knowledge of Bluetooth and RF technologies.
By default, the WT12 module is equipped with powerful and easy-to-use
iWRAP firmware. iWRAP enables users to access Bluetooth functionality
with simple ACSII commands delivered to the WT12 module over the
UART interface.
Besides the iWRAP firmware, the module has an option for other firm-
ware options. Standard Host Command Interface (HCI) firmware is
supported – an ideal solution for systems where the host system is capable
of running the entire Bluetooth stack and profiles, and the WT12 module
is utilized as the physical radio over the UART interface.
USB Interface
The device operates as a USB peripheral responding to requests from a
master host controller, such as a PC. Both the OHCI and UHCI stan-
dards are supported. The set of implemented USB endpoints can behave
as specified in the USB section of the Bluetooth v 2.0 and EDR specifica-
tion or, alternatively, can appear as a set of endpoints appropriate to USB
audio devices, such as speakers.
Bluetooth EZ-Extender Manual
1-5
Expansion Interface
Expansion interface connectors on top of the Bluetooth EZ-Extender
allow other EZ-Extenders to be mounted on top of the Bluetooth
EZ-Extender. The UART interface is not brought up to the expansion
interface because the interface is used by the WT12 Bluetooth module. All
other signals are passed up to the expansion interface from the mating
EZ-KIT Lite or EZ-Board through the Bluetooth EZ-Extender.
Example Programs
For more information about using the Bluetooth EZ-Extender and run-
ning µClinux on a Blackfin processor, go to
1-6
Bluetooth EZ-Extender Manual
2 BLUETOOTH EZ-EXTENDER
HARDWARE REFERENCE
This chapter describes the hardware design of the Bluetooth EZ-Extender.
• “System Architecture” on page 2-2
Describes the daughter board’s configuration and explains how the
board components interface with the processor and EZ-Board.
Shows the location and describes the board’s configuration switch.
Shows the location and describes the board’s jumpers.
• “Power LED” on page 2-7
Shows the location and describes the board’s power LED.
• “Connectors” on page 2-8
Shows the locations, describes, and provides part numbers for the
on-board connectors. In addition, the manufacturer and part num-
ber information is provided for the mating parts.
Bluetooth EZ-Extender Manual
2-1
System Architecture
System Architecture
A block diagram of the Bluetooth EZ-Extender is shown in Figure 2-1.
Figure 2-1. Bluetooth EZ-Extender Block Diagram
The block diagram illustrates how the UART, SPORT, and USB ports are
interfaced the Bluetooth module and processor on a mating EZ-KIT
Lite/EZ-Board. The block diagram is a high-level diagram and does not
show the voltage translation circuitry or the clock buffers. The schematic
pages are available in “Bluetooth EZ-Extender Schematic” on page B-1.
The board supports 3.3, 2.5, and 1.8 volt I/O. The on-board voltage
translator automatically translates the motherboard signals to the correct
voltage levels.
2-2
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
The board contains a Bluegiga WT12 class 2, a Bluetooth 2.0, and EDR
module, described in “Bluetooth Module” on page 1-5. The EZ-Extender
2
is equipped with an I C serial flash memory chip for data storage and
configuration.
Configuration Switch
This section describes the board’s configuration switch (SW1). The switch
location is shown in Figure 2-2.
Figure 2-2. Configuration Switch Location
Bluetooth EZ-Extender Manual
2-3
Configuration Switch
Positions 7 and 8 of the configuration switch enable or disable UART
flow control. Other switch positions are intended for internal Analog
Devices test purposes only and not supported.
By default, SW1 is all OFF. The switch settings are shown in Table 2-1.
Table 2-1. Configuration Switch (SW1)
SW1 Position
SW1.1
UART Flow Control Off
UART Flow Control On
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
SW1.2
SW1.3
SW1.4
SW1.5
SW1.6
SW1.7
SW1.8
ON
2-4
Bluetooth EZ-Extender Manual
Jumpers
TWI Flash Address Configuration Jumper (JP1)
The TWI flash address configuration jumper (JP1) controls the base
address of the configuration flash memory. When multiple EZ-Extenders
are stacked on top of each other, it may be necessary to change the JP1set-
ting to avoid any conflict with the configuration flash memory on another
EZ-Extender. The default is no jumper installed.
TWI Flash Write Protect Jumper (JP2)
The TWI flash write protect jumper (JP2) is not available; the jumper is
intended for internal Analog Devices test purposes only. The default is no
jumper installed.
Soft Reset Configuration Jumpers (JP3–4)
The software reset configuration jumpers (JP3—4) determine which GPIO
signal is used to perform a soft reset of the Bluegiga WT12 Bluetooth
module. The default is no jumpers installed.
Bluetooth Module Default Configuration Jumper
(JP5)
The Bluegiga WT12 Bluetooth module default configuration jumper
(JP5) resets the module’s settings to the default values. This feature
requires software support; refer to the example programs for more infor-
mation. The default is no jumper installed.
UART Receive Data Jumper (JP6)
The UART receive data jumper (JP6) is not available; the jumper is
intended for internal Analog Devices test purposes only. The default is no
jumper installed.
2-6
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
STAMP UART Connector (J1)
be plugged onto an EZ-KIT Lite development board supporting a
STAMP interface. The J1 connector is located on the bottom side of the
board. For availability and pricing of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-6 or more information.
Part Description
Manufacturer
SAMTEC
Part Number
10-position 0.1”, SMT socket
SSW-105-22-F-D-VS
Mating Connector
SAMTEC TSSH
10-position 0.1’’, SMT header
TSSH-105-01-L-DV-A
Expansion Interface II Connector (J3)
UART, SPORT interfaces and general-purpose I/O (GPIO) signals of the
mating EZ-Board. The connector is located on the bottom side of the
board. For availability and pricing of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-6 for more information.
Part Description
Manufacturer
SAMTEC
Part Number
50-position 0.1’’, SMT socket
SSW-125-22-F-D-VS
Mating Connector
SAMTEC
50-position 0.1’’, SMT header
TSSH-125-01-L-DV-A
Bluetooth EZ-Extender Manual
2-9
Connectors
Expansion Interface II Connector (J5)
interfaces and GPIO signals of the mating EZ-Board. The connector is
located on the bottom side of the board. For availability and pricing of the
connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-6 for more information.
Part Description
Manufacturer
SAMTEC
Part Number
70-position 0.1’’, SMT socket
SSW-135-22-F-D-VS
Mating Connector
SAMTEC
70-position 0.1’’, SMT header
TSSH-135-01-L-DV-A
Expansion Interface II Connector (P2)
SPORT interfaces and GPIO signals of the mating EZ-Board. The con-
nector is located on the top side of the board. For availability and pricing
of the connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-6 for more information.
Part Description
Manufacturer
SAMTEC
Part Number
50-position 0.1’’, SMT socket
TSSH-125-01-L-DV-A
Mating Connector
SAMTEC
50-position 0.1’’, SMT header
SSW-125-22-F-D-VS
2-10
Bluetooth EZ-Extender Manual
Bluetooth EZ-Extender Hardware Reference
Expansion Interface II Connector (P4)
interfaces and GPIO signals of the mating EZ-Board. The connector is
located on the top side of the board. For availability and pricing of the
connectors, contact Samtec.
Refer to “Expansion Interface” on page 1-6 for more information.
Part Description
Manufacturer
SAMTEC
Part Number
70-position 0.1’’, SMT socket
TSSH-135-01-L-DV-A
Mating Connector
SAMTEC
70-position 0.1’’, SMT header
SSW-135-22-F-D-VS
USB Connector (P3)
Part Description
Manufacturer
MOLEX
Part Number
USB Mini-B connector
0675031010
Mating Connector
ASSMANN
USB Mini-B to USB A cable
AK672M/2-3
Bluetooth EZ-Extender Manual
2-11
Connectors
2-12
Bluetooth EZ-Extender Manual
A BLUETOOTH EZ-EXTENDER
BILL OF MATERIALS
The bill of materials corresponds to “Bluetooth EZ-Extender Schematic”
on page B-1.
Ref. Qty. Description
Reference
Designator
Manufacturer
DIGI-KEY
TI
Part Number
1
2
1
1
SN74LVC1G14DB
VR SOT23-5
U4
U8
296-11607-1-ND
SN74LVC1G08DBVR
SN74LVC1G08
SOT23-5
3
4
5
1
1
1
WT12 ICS010
U3
U7
U2
BLUEGIGA
MICREL
WT12-A-AI
MIC94040 MLF4
MIC94040YFL
M24C02-RDW6TP
M24C02
ST MICRO
TSSOP8DW
6
7
8
1
1
1
SN74ALVC125
TVSOP14
U9
TI
SN74ALVC125DGVRE4
ADG3231BRJZ-REEL
ADG3308BRUZ
ADG3231 SOT23-6 U5
ANALOG
DEVICES
ADG3308
TSSOP20
U1
ANALOG
DEVICES
9
1
1
DIP8 SWT016
SW1
JP1
C&K
TDA08H0SB1
10
IDC 3X2
SAMTEC
TSM-103-01-T-DV
IDC3X2_SMT
11
12
1
1
USB_MINI-B 5PIN P3
CON028
MOLEX
FCI
0675031010
IDC 2X2 IDC2X2
JP4
68737-404HLF
Bluetooth EZ-Extender Manual
A-1
Ref. Qty. Description
Reference
Manufacturer
Part Number
Designator
13
14
1
1
IDC 4X2 IDC4X2
JP3
P2
SULLINS
SAMTEC
GEC04DAAN
IDC 25x2
TSSH-125-01-L-DV-A
IDC25x2_SMTA
15
16
17
18
19
20
21
1
IDC 35x2
IDC35x2_SMTA
P4
SAMTEC
SAMTEC
SAMTEC
SAMTEC
SAMTEC
AVX
TSSH-135-01-L-DV-A
SSW-135-22-F-D-VS
SSW-125-22-F-D-VS
TSM-102-01-T-SV
1
IDC 35X2
IDC35x2_SMT_F
J5
1
IDC 25X2
IDC25x2_SMT_F
J3
3
IDC 2X1
IDC2X1_SMT
JP2,JP5-6
J1
1
IDC 5X2
IDC5x2_SMT_F
SSW-105-22-F-D-VS
0402ZD104KAT2A
CRCW040210K0FKED
12
9
0.1UF 10V 10%
0402
C1-12
10K 1/16W 5%
0402
R1-4,R6,R14-17
VISHAY
22
23
7
1
22 1/16W 5% 0402 R11-12,R18-22
PANASONIC
PANASONIC
ERJ-2GEJ220X
ERJ-3GEYJ152V
1.5K 1/10W 5%
0603
R8
24
1
330 1/10W 5%
0603
R5
VISHAY
CRCW0603330RJNEA
25
26
1
1
GREEN LED001
LED1
R9
PANASONIC
ROHM
LN1361CTR
47.0K 1/16W 1%
0402
MCR01MZPF4702
27
28
2
2
10NH 5% 0402
L1-2
PANASONIC
PANASONIC
ELJ-QF10NJF
ERJ-2GEJ153X
15K 1/16W 5%
0402
R7,R13
29
1
27K 1/16W 5%
0402
R10
PANASONIC
ERJ-2GEJ273X
A-2
Bluetooth EZ-Extender Manual
A
B
C
D
1
2
3
4
1
2
3
4
BLUETOOTH DAUGHTERBOARD
20 Cotton Road
ANALOG
DEVICES
Nashua, NH 03063
PH: 1-800-ANALOGD
Title
BLUETOOTH EZ-EXTENDER
TITLE
Size
C
Board No.
Rev
1.1
4
A0218-2008
3-27-2009_11:41
1
Date
Sheet
of
A
B
C
D
A
B
C
D
3.3V
L1
10NH
0402
L2
10NH
0402
C1
0.1UF
0402
C2
0.1UF
0402
C3
0.1UF
0402
C4
0.1UF
0402
1
2
3
4
1
2
3
4
V_SELECT
3.3V
SW1
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
R18
22
0402
R16
10K
0402
R15
R7
15K
0402
R13
15K
0402
10K
0402
SWT016
DIP8
JP6
U3
1
26
5
TP7
TXD
RTS
RXD
CTS
2
30
R8
1.5K
0603
RF
IDC2X1_SMT
3
4
PIO2
PIO3
PIO4
PIO5
PIO6
PIO7
6
R11
22
U1
10
1
20
20
25
18
19
0402
VCCA
VCCY
2
3
4
5
6
7
8
9
19
18
17
16
15
14
13
12
8
9
A1
A2
A3
A4
A5
A6
A7
A8
Y1
Y2
Y3
Y4
Y5
Y6
Y7
Y8
D+
D-
R12
22
0402
TP3
TP4
TP5
TP6
V_SELECT
22
21
23
24
SCLK
SPICS
MISO
MOSI
7
11
12
13
17
PCMO
PCMI
PCMC
PCMS
RESET
R19
22
U9
R10
27K
0402
R9
47.0K
0402
VCC
0402
2
1
3
27
1A
1Y
NC
R20
22
0402
11
10
GND
EN
1OE
2A
ADG3308
TSSOP20
5
6
2Y
R22
22
0402
WT12
ICS010
4
2OE
U5
9
8
1
3
4
6
5
3A
3Y
VCCA
VCCY
R21
22
0402
P3
U8
10
12
13
1
2
U4
1
2
3
5
6
3OE
4A
VCC
4
2
4
A
Y
11
4Y
D-
D+
SN74LVC1G08
SOT23-5
JP4
SN74LVC1G14DBVR
SOT23-5
4OE
GND
1
2
4
GND
SN74ALVC125
TVSOP14
ADG3231
SOT23-6
GND
3
SHELL
IDC2X2
JP3
1
3
5
7
JP5
1
CON028
2
2
4
6
8
IDC2X1_SMT
R14
10K
0402
R17
10K
0402
IDC4X2
V_SELECT
3.3V
U2
8
1
2
3
4
R4
10K
0402
VCC
E0
V_SELECT
3.3V
JP1
1
6
SCL
2
4
6
5
SDA
3
5
E1
JP2
E2
LED1
GREEN
LED001
7
1
2
WC
IDC3X2_SMT
GND
IDC2X1_SMT
C8
0.1UF
0402
C6
0.1UF
0402
C11
0.1UF
0402
C12
0.1UF
0402
C7
C9
0.1UF
0402
C10
0.1UF
0402
M24C02
TSSOP8DW
0.1UF
0402
R5
330
0603
R3
10K
0402
R1
10K
0402
R2
10K
V_SELECT
0402
20 Cotton Road
ANALOG
DEVICES
Nashua, NH 03063
PH: 1-800-ANALOGD
C5
0.1UF
0402
Title
BLUETOOTH EZ-EXTENDER
MODULE
Size
C
Board No.
Rev
1.1
4
A0218-2008
3-27-2009_11:41
2
Date
Sheet
of
A
B
C
D
A
B
C
D
1
2
3
4
1
2
3
4
3.3V
V_SELECT
J3
P2
2
1
1
2
PWR_IN1
GND1
GND2
GND3
GND4
GND5
GND6
DTPRI
DTSEC
TSCLK
TFS
GND1
PWR_IN1
PWR_IN2
VDDIO1
VDDIO2
3.3V1
4
3
3
4
PWR_IN2
VDDIO1
VDDIO2
3.3V1
GND2
GND3
GND4
GND5
GND6
DTPRI
DTSEC
TSCLK
TFS
6
5
5
6
8
7
7
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
9
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
3.3V2
3.3V2
DRPRI
DRSEC
RSCLK
RFS
DRPRI
DRSEC
RSCLK
RFS
3.3V
V_SELECT
SPISEL2 SPISEL1
SPISEL1 SPISEL2
SPICLK
SPISS
TIMER
SDA
SPISEL3
SPIMOSI
SPIMISO
SCL
SPISEL3
SPIMOSI
SPIMISO
SCL
SPICLK
SPISS
TIMER
SDA
U7
IN
3
1
2
OUT
UARTRX UARTTX
UARTCTSUARTRTS
UARTTX UARTRX
UARTRTSUARTCTS
4
EN
GND
MIC94040
MLF4
NC
RESET
GPIO1
GPIO3
WAKE
RSVD3
RSVD5
RSVD7
RSVD9
RESET
GPIO1
GPIO3
WAKE
RSVD2
RSVD4
RSVD6
RSVD8
NC
GPIO2
GPIO4
RSVD1
RSVD3
RSVD5
RSVD7
RSVD9
GPIO2
GPIO4
RSVD2
RSVD4
RSVD6
RSVD8
RSVD10
J1
2
4
6
8
1
3
5
7
9
10
IDC5X2_SMT_F
IDC25X2_SMT_F
IDC25X2_SMTA
R6
10K
0402
20 Cotton Road
ANALOG
DEVICES
Nashua, NH 03063
PH: 1-800-ANALOGD
Title
BLUETOOTH EZ-EXTENDER
LS CONNECTOR
Size
C
Board No.
Rev
1.1
4
A0218-2008
3-27-2009_11:41
3
Date
Sheet
of
A
B
C
D
A
B
C
D
1
2
3
4
1
2
3
4
3.3V
V_SELECT
J5
P4
2
1
1
2
PWR_IN1
PWR_IN2
VDDIO1
GND1
GND2
GND1
PWR_IN1
PWR_IN2
VDDIO1
4
3
3
4
GND2
6
5
5
6
GND3
GND3
8
7
7
8
VDDIO2
GND4
GND4
VDDIO2
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
9
9
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
70
3.3V1
GND5
GND5
3.3V1
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
69
3.3V2
GND6
GND6
3.3V2
PPI0FS2
PPI0CLK
PP0D0
PPI0FS1
PPI0FS3
PPI0D1
PPI0D3
PPI0D5
PPI0D7
PPI0D9
PPI0D11
PPI0D13
PPI0D15
PPI0D17
PPI0FS1
PPI0FS3
PPI0D1
PPI0FS2
PPI0CLK
PPI0D0
PPI0D2
PPI0D3
PPI0D2
PPI0D4
PPI0D5
PPI0D4
PPI0D6
PPI0D7
PPI0D6
PPI0D8
PPI0D9
PPI0D8
PPI0D10
PPI0D12
PPI0D14
PPI0D16
TIMER1/GPIO
TIMER3/GPIO
PPI1FS2
PPI1CLK
PP1D0/PPI0D18
PPI1D2/PPI0D20
PPI1D4/PPI0D22
PPI1D6
PPI0D11
PPI0D13
PPI0D15
PPI0D17
TIMER2/GPIO
RESET
PPI0D10
PPI0D12
PPI0D14
PPI0D16
TIMER1/GPIO
TIMER3/GPIO
PPI1FS2
PPI1CLK
PP1D0/PPI0D18
PPI1D2/PPI0D20
PPI1D4/PPI0D22
PPI1D6
TIMER2/GPIO
RESET
PPI1FS1
PPI1FS3
PPI1D1/PPI0D19
PPI1D3/PPI0D21
PPI1D5/PPI0D23
PPI1D7
PPI1FS1
PPI1FS3
PPI1D1/PPI0D19
PPI1D3/PPI0D21
PPI1D5/PPI0D23
PPI1D7
PPI1D8
PPI1D9
PPI1D9
PPI1D8
PPI1D10
PPI1D12
PPI1D14
PPI1D16
NC
PPI1D11
PPI1D13
PPI1D15
PPI1D17
SDA
PPI1D11
PPI1D13
PPI1D15
PPI1D17
SDA
PPI1D10
PPI1D12
PPI1D14
PPI1D16
NC
RSVD2
SCL
SCL
RSVD1
RSVD4
RSVD5
RSVD2
RSVD3
RSVD6
RSVD7
RSVD4
RSVD5
RSVD8
RSVD9
RSVD6
RSVD7
IDC35X2_SMT_F
IDC35X2_SMTA
20 Cotton Road
ANALOG
DEVICES
Nashua, NH 03063
PH: 1-800-ANALOGD
Title
BLUETOOTH EZ-EXTENDER
PPI CONNECTOR
Size
C
Board No.
Rev
1.1
4
A0218-2008
3-27-2009_11:41
4
Date
Sheet
of
A
B
C
D
I INDEX
expansion interface II
overview, 1-6
A
architecture, of this EZ-Extender, 2-2
J5 connector, 2-10
P2 connector, 2-10
P4 connector, 2-11
B
bill of materials, A-1
Bluetooth module, 1-5, 2-2
Bluetooth module default config jumper (JP5),
2-6
F
board schematic (Bluetooth EZ-Extender), B-1
C
configuration, of this EZ-Extender, 1-4
configuration switch (SW1), 2-3
connectors
JP5 (Bluetooth module default config), 2-6
JP6 (UART receive data jumper), 2-6
diagram of locations, 2-8
J1 (STAMP UART), 2-9
J3 (expansion interface), 2-9
J5 (expansion interface), 2-10
P2 (expansion interface), 2-10
P3 (USB), 2-11
P4 (expansion interface), 2-11
contents, of this EZ-Extender package, 1-2
customer support, xii
L
LED1 (power), 2-7
D
notation conventions, xvi
default configuration, of this EZ-Extender, 1-3
P
E
power LED (LED1), 2-7
product overview, x
EDR module, 1-5, 2-3
Bluetooth EZ-Extender Manual
I-1
INDEX
S
schematic, of Bluetooth EZ-Extender, B-1
setup, of this EZ-Extender, 1-3, 1-4
soft reset config jumpers (JP3-4), 2-6
STAMP UART connector (J1), 2-9
supported products, xiii
interface, 1-4, 1-6
receive data jumper (JP6), 2-6
USB
connector (P3), 2-11
interface, 1-5
switch, SW1 (configuration), 2-3
system architecture, of this EZ-Extender, 2-2
V
T
voltage translator, 2-2
TWI flash address config jumper (JP1), 2-6
TWI flash write protect jumper (JP2), 2-6
W
WT12 Bluetooth module, 1-6
WT12 module, 1-5, 2-3
I-2
Bluetooth EZ-Extender Manual
|