Zephyr Ventilation Hood Z1C 00SL User Manual

customer service  
1.888.880.8368  
Duct Cover Extension  
Z1C-00SL  
For use with Surface Is. range hood  
Mounting the duct cover  
Fixation des cheminees  
Fijación de las chimeneas  
Fissaggio dei camini  
Pag. 4  
Pag. 6  
Pag. 8  
Pag. 10  
 
MOUNTING THE DUCT COVER  
1. Before installing the duct cover extension kit, take out the duct cover ceiling bra-  
cket fom the range hood packaging and remove the bracket by unscrewing the (4)  
screws.  
2. Remove the duct cover from the hood assembly, according to the following steps:  
A - Take out the lower mantle by removing the (7) screws. Fig. 1  
B - Take out the spacer, by removing the (6) plus (4) metric screws and the bushes.  
Fig. 2  
C - Take out the two additional bushes that secure the glass. Fig. 3  
3. Take the lower duct cover from the duct cover extension kit and secure it to the  
hood assembly by following the instructions from step 2 in reverse order.  
- 3 -  
 
4. Remove the (2) screws to unlock the top support frame from the bottom support  
frame. Fig.4.  
5. Secure the top support frame to the duct  
cover ceiling bracket by using the (4)  
screws. Fig. 5  
6. Position hole template on the ceiling paying  
attention that the arrow is positioned on  
the same side as the range hood controls.  
- Make 4 holes in the ceiling and drive in (3)  
screws without completely tightening  
them. Pay attention not to insert the screw  
into the hole marked with an X on the hole  
template. Fig.6  
7. Lift the hood assembly to the ceiling and  
align the top support frame and ceiling bra-  
cket with the (3) screws previously installed  
in the ceiling.  
Rotate assembly slightly clockwise to lock in  
place.  
Drive in the fourth screw and tighten the re-  
maining 3 screws to secure the structure in  
place with con ulteriori (4) viti. Fig.6  
8. Insert the bottom support frame into the  
top support frame. Fig.7  
5 - 1/2"  
24"  
X = C - (5-1/2" + 24" + B)  
- 4 -  
 
Adjust height by referring to the diagram in fig.8.  
Secure the support frames together using (2)  
screws per extension arm (8 total). Fig.9  
9. Insert the motor housing into the support frame  
assembly and secure it using (8) screws. Fig.10  
10. Connect the equipment to the power supply.  
11. Secure the correct size ducting for your instal-  
lation (not supplied) to the collar on top of the  
housing. Fig.11  
12. Extend upper duct cover to the ceiling and  
secure it to the duct cover ceiling bracket using  
the (4) screws previously removed when the as-  
sembly was taken out of the packaging. Fig. 12  
13. Lift the hood assembly into the top duct cover.  
Secure hood assembly to bottom support frame by using  
(4) screws. Fig. 13  
14. Verify that ducting from hood is connected to ducting  
in the attic that will exhaust air out of the home.  
- 5 -  
 
3FA0174  
 

Weider Home Gym 831157110 User Manual
Weider Home Gym WESY39311 User Manual
Whirlpool Clothes Dryer 6LE5700XSW0 User Manual
Whirlpool Range WFG361LVS User Manual
Whirlpool Washer Front Loading Automatic Washer User Manual
Wolfgang Puck Gas Grill BCGL0050 User Manual
Xerox Copier Phaser 6100 User Manual
XM Satellite Radio Satellite Radio SR9600A User Manual
Yamaha Outboard Motor F30A User Manual
Zanussi Oven ZOD 890 User Manual