Xerox Copier 8855 721P User Manual

Xerox Wide Format Solutions  
8855/721P Stacker  
Operator Manual  
THE DOCUMENT COMPANY  
XEROX  
701P39432  
 
Table of Contents  
It’s Illegal ..................................................................... 2  
FCC Compliance ......................................................... 2  
Introduction to your Stacker ...................................... 3  
Safety Notes ................................................................ 4  
Identifying the Parts on the Stacker .......................... 6  
Location of the Stacker Serial Number ...................... 7  
Stacker Operation ....................................................... 7  
Stacker Jam Clearance ............................................... 7  
Stacker Relocation ....................................................... 8  
Technical Data ............................................................ 9  
1
 
2
It’s Illegal  
In the USA  
FCC Compliance  
In the USA  
It is against U.S. law to copy copyrighted material without permission  
of the copyright owner unless the copying falls within the “Fair Use”  
library reproduction rights of the copyright law.  
Class A  
This equipment has been tested and found to comply with the limits  
for a Class A digital device, pursuant to Part 15 of the FCC rules.  
These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with  
the instruction manual, may cause harmful interference to radio  
communication. Operation of this equipment in a residential area is  
likely to cause harmful interference, in which case the user will be  
required to correct the interference at their own expense.  
Further information on these U.S. provisions may be obtained from  
the Copyright Office, Library of Congress, Washington, D.C. 20550,  
or telephone the Copyright Office at (202) 707-9100 and ask for  
circular 21. Copying other items may be prohibited. If you have any  
questions seek legal advice.  
If necessary, the user should consult the dealer or an experienced  
radio/television technician for additional suggestions. The user may  
find the following booklet prepared by the Federal Communications  
Commission helpful:  
How to Identify and resolve Radio-TV Interference Problems  
Stock Number: 004-000-00345-4.  
 
FOR SERVICE:1-800-822-2979  
Introduction to Your Stacker  
A Customer Service Support Representative will assist you in  
keeping your stacker operational and, if required, will arrange for a  
Customer Service Engineer to visit your stacker and restore its  
performance.  
Congratulations on acquiring your new Stacker.  
This User Guide provides information that is needed to operate the  
Stacker.  
The information below is needed when you call your Xerox support  
experts.  
PURCHASE OF OTHER EQUIPMENT:  
Call a local Marketing Representative. They will assist you in  
determining and ordering other office equipment that will further  
increase your productivity.  
1. Customer Account Number: __________________  
2. Stacker Serial Number: _____________________  
To Locate the Stacker Serial Number, refer to page 7.  
3. Printer Serial Number: ______________________  
To Locate the Printer Serial Number, refer to Printer User Guide.  
Local Marketing Representative phone number:  
____________________________  
Note: All service calls should be reported under the printer serial  
number.  
3
 
4
Safety Notes  
Your stacker has been designed and tested to meet strict safety requirements. These include safety agency examination and approval, and  
compliance to established environmental standards. Please read the following instructions carefully before operating the Stacker.  
NOTE: Refer to Instructions as needed to ensure the continued safe operation of your stacker.  
FOLLOW all warnings and instructions marked on or supplied with the product.  
UNPLUG the stacker from the wall outlet before cleaning. Always  
use materials supplied or approved by Xerox. Use of other materials  
may result in poor performance and could create a hazardous  
situation.  
IF AN EXTENSION CORD is used with this stacker, ensure that the  
total of the ampere ratings of the products plugged into the extension  
cord does not exceed the extension cord ampere rating. Also, make  
sure that the total amperage of all products plugged into the wall  
outlet does not exceed the outlet protection.  
DO NOT use aerosol cleaners  
DO NOT install the stacker in direct sunlight, a high humidity or dusty  
environment.  
NEVER use supplies or cleaning materials for purposes other than  
what they were intended. Keep all supplies and materials out of  
reach of children.  
DO NOT install the stacker where the floor or base is unstable. The  
stacker may fall, causing personal injury and/or serious damage to  
the stacker.  
DO NOT use the stacker near water, wet locations, or outdoors.  
WARNING  
NEVER spill liquid of any kind on the stacker.  
This copier must be grounded.  
DO NOT allow anything to rest on the power cord. Do not locate this  
stacker where people will step on the cord.  
THIS PRODUCT is equipped with a 3-wire grounding-type plug (i.e.,  
a plug having a third grounding pin) and an additional safety device.  
This plug will only fit into a grounding-type power outlet. This is a  
safety feature. To avoid risk of electric shock, contact your  
electrician to replace the receptacle if you are unable to insert the  
plug into the outlet. Never use a ground adapter plug to connect the  
copier to a power source receptacle that lacks a ground connection  
terminal.  
NEVER remove any covers or guards that require a tool for removal.  
There are no operator-serviceable areas within these covers.  
THE POWER SUPPLY CORD is the disconnect device for this  
stacker. Ensure that installation is near the outlet and is easily  
accessible.  
NEVER attempt any function that is not specified in this User Guide  
THIS STACKER should be operated from the type of power source  
indicated on the marking label. If you are not sure of the type of  
power available, consult your local power company.  
or directed by an authorized Xerox representative.  
 
Safety Notes (continued)  
UNPLUG this stacker from the wall outlet and refer servicing to  
qualified service personnel under the following conditions:  
When the power cord is damaged or frayed.  
If liquid has been spilled into the product.  
If the stacker has been exposed to rain or water.  
If the stacker is producing unusual noises or odors.  
If the stacker has fallen or the cabinet has been damaged.  
The safety feature has been activated for a second time.  
The stacker still does not work, or continues to  
malfunction, after following the procedures in this User  
Guide.  
If you need additional safety information concerning the copier or  
materials supplied by Xerox, you may call the following toll-free  
number: 1-800-828-6571.  
5
 
6
Identifying the Parts on the Stacker  
Upper Panel Assembly  
Stacker Unit  
Inlet  
Power Switch  
Power Indicator  
Light  
Printed Wiring Board  
(Transmission)  
Media Supports  
Release Handle  
Thumb Screws  
Printed Wiring Board  
(Reception)  
Release Handle  
Frame Assembly  
 
Location of the Stacker Serial Number  
Stacker Jam Clearance  
In order to locate the serial number of your stacker, you must first  
push down the release lever and slide the stacker away from the  
printer.  
The paper fed from the printer will be either cut or uncut.  
Caution  
To ensure the safety of the user, be aware during jam  
clearance that the surface will be hot.  
The serial number plate is located on the left of the front cover facing  
the printer.  
Cut  
In order to clear a jam in the stacker, lift the Upper Panel Assembly  
and clear any paper (Figure 2). If the jam still exists, push down on  
the release lever and move the stacker away from the printer (Figure  
1). Clear any visible paper from the paper path.  
Serial Number Plate  
Uncut  
Cut the paper in the printer (refer to the printer user guide) and follow  
the above procedure.  
Caution Hot Label  
Jam Clearance Label  
Upper Panel Assembly  
Figure 1. Sliding the Stacker away from the Printer.  
Stacker Operation  
If you are running paper larger than a 24” (610mm) raise the paper  
supports.  
In order to turn on your stacker, press the power switch to the on  
position. When the stacker is on the green Power Indicator Light is  
visible.  
Figure 2. Lifting the Upper Panel Assembly.  
NOTE; The Transmission PWB and the Reception PWB are infrared  
connections (See Identifying the Parts on the Stacker). To ensure  
proper operation of the stacker, these connections must be debris  
free.  
NOTE: There is no start up sequence between the stacker and the  
printer (either the stacker or the printer may be turned on first). If  
your stacker does not run, turn off both the printer and the stacker.  
Turn on the stacker then turn on the printer. If the stacker still does  
not function, verify power source and then call for service.  
7
 
8
Top View  
Stacker Relocation  
The stacker cannot be moved except by a DRC rigger.  
Stacker  
power cord  
12'  
66"  
(168cm)  
To ensure that the stacker operates reliably after moving it to a new  
location, consider the following guidelines:  
Printer  
power cord  
12'  
(3.66m)  
Stacker  
S
The new location must provide minimum clearances around the  
stacker. These clearances are shown in the diagram on the  
right.  
153.5”  
(390cm)  
S
S
The flooring in the new location must be adequate to support the  
weight of the stacker and be reasonably level.  
39.5"  
(100cm)  
721P  
The new location must be well ventilated and maintain an even  
temperature. Extreme temperature or humidity changes can  
affect the stacker.  
48"  
(122cm)  
S
Power source receptacles must be properly grounded.  
35"  
57"  
65"  
(165cm)  
In addition to the above requirements, the surface must be at least  
157” (400cm) x153.5” (390cm) and be capable of supporting at least  
108lb (49kg) stacker and the 880lb (400kg) printer attached.  
(90cm)  
(145cm)  
157”  
(400cm)  
 
Technical Data  
Dimensions: Width: 34” (864mm)  
57.5” (1461mm) w/paper supports extended.  
Depth: 41” (1041mm)  
Height: 28.5” (724mm)  
Weight: 108 lbs. (49kg)  
Paper Size: 36 x 48” (914mm x 1219mm) Max.  
Stacker Capacity: 200 sheets of plain paper with minimal scatter  
500 plain paper sheets Max.  
Electrical Data:  
Current service: 3 Amps or more  
Power Supply: 110V - 240V  
Frequency: 50/60Hz  
Power Consumption: 60W  
Temperature: 50LF - 90LF (10LC - 32LC)  
Humidity: 20 - 85%  
Noise Level: 57dB Max. (during operation)  
9
 

Weed Eater Trimmer 545186837 User Manual
Weider Home Gym WESY85290 User Manual
Whirlpool Cable Box ET4WSKXKQ02 User Manual
Whirlpool Range 8522773A User Manual
Windsor Mobility Aid Elevator User Manual
Wolfgang Puck Blender WPMFP15 User Manual
Wolfgang Puck Mixer BHM00240 User Manual
Wolf Griddle RCSIZEE User Manual
Woodstock Drill D4033 User Manual
Woodstock Switch D4159 User Manual