Well Traveled Living Indoor Fireplace 60353 User Manual

 
Use this appliance only as described in this manual. Any other use not recommended  
by the manufacturer may cause fire, electric shock or injury to persons.  
Avoid the use of an extension cord because the extension cord may overheat and  
cause a risk of fire. However, if you have to use an extension cord, the cord shall be  
14 gauge minimum size and rated not less that 2025 watts. The extension cord must  
be a three wire cord with grounding type plug and cord connector. The extension  
cord shall not be more than 20 feet in length.  
17.  
18.  
SPECIFICATIONS  
Dimensions LxWxH  
15.56"x23.09"x28.37"  
54.5 lbs  
Net Weight  
Voltage  
110-120V  
60 Hz  
Frequency  
Watts  
1350 W  
Heater Rating  
4600 BTU  
ELECTRICAL CONNECTION  
A 15 Amp, 110 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this  
appliance. The fireplace must be on a dedicated circuit as other appliances on the same  
circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in opera-  
tion. The unit comes standard with a 6.5 ft long 3 wire cord, exiting out the back of the  
fireplace. Plan the installation to avoid the use of an extension cord. If an extension cord  
must be used, it must be a minimum 14 gauge, 3 wire with grounding type plug and  
connector and rated not less than 2025 watts. The extension cord shall not be more than  
20 ft in length.  
WARNING: Electrical outlet wiring must comply with local building codes and other  
applicable regulations to reduce the risk of fire, electrical shock and injury to persons.  
WARNING: Do not use this fireplace if any part of it has become wet. Immediately call a  
qualified service technician to inspect the fireplace and replace any part of the electrical  
system which has been wet.  
 
CONTROLS/LEG ASSEMBLY  
Your fireplace has the following functions:  
Leg Assembly:  
Lay stove on a flat surface. Attach 4 legs  
with screws provided as shown in Fig. 1:  
High heat  
1350 watts  
Low heat  
700 watts  
On/Off  
Power to the unit  
Fig. 1  
Please note: Both the low heat and high heat  
switches must be in the on position to achieve  
high heat.  
FOR YOUR SAFETY  
Service must be performed by a qualified service agency.  
REPLACING THE LIGHT BULBS  
This fireplace uses 2 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base,  
chandelier candle type bulbs). The access plate is located on the back of the unit. For  
convenience, if one of the light bulbs burns out, it may be easier to replace both of the  
light bulbs at the same time.  
WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may result in a  
fire, causing property damage, personal injury or loss of life.  
FIG 1  
FIG 2  
1. Turn off the power to the unit, and unplug it from the electrical outlet.  
2. Let the fireplace cool if it has been operating.  
 
3. Turn the fireplace so you are facing the back of the fireplace.  
4. Look for the access plate with the gold printing on it.  
5. Remove the 3 screws holding the access plate in position (FIG1). Once you have  
removed the 3 screws, lift the access plate so the 2 positioning tabs come free of  
their slots. Once you have removed the access plate you can see and access the two  
40 watt chandelier bulbs (FIG 2).  
6. Remove each light bulb by unscrewing them out of the bases, turning them  
counterclockwise. You can use one hand to hold the light socket in place, if required.  
7. Install the new light bulbs by turning each light bulb into the base clockwise. You can  
use one hand to hold the light socket in place, if required.  
8. Replace the access plate by inserting the 2 tabs, pushing the plate up against the  
fireplace back, and inserting the 3 screws.  
9. Turn the fireplace back so you are facing the front of the fireplace.  
10. Plug the fireplace back into the electrical outlet and turn the power on and enjoy the  
flame effect.  
CLEANING  
Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat and vent  
area clean from dust and dirt. The exterior of the fireplace should be cleaned with a  
damp cloth or duster. Do not use abrasive cleaners, liquid sprays, or any other cleaner  
that may scratch the surface.  
 
 

West Bend Egg Cooker Egg Cooker User Manual
Whirlpool Clothes Dryer CGM2761KQ1 User Manual
Whirlpool Refrigerator 3VET16GKGW01 User Manual
Whirlpool Trash Compactor TU800SPPB1 User Manual
White Rodgers Thermostat 1F90 60 User Manual
Wolf Ventilation Hood PL582212 User Manual
Xantrex Technology Wireless Office Headset 809 0912 User Manual
Yamaha Offroad Vehicle 1P1 F8199 13 User Manual
Zanussi Refrigerator ZRB 3225 X User Manual
Zanussi Ventilation Hood 642000 User Manual