Well Traveled Living Indoor Fireplace 60351 User Manual

VERNON ELECTRIC FIREPLACE  
MODEL # 60351  
CARE & USE GUIDE  
Please read this manual before  
installing and using your fireplace.  
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN  
ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE,  
PERSONAL INJURY OR LOSS OF LIFE.  
 
Use this appliance only as described in this manual. Any other use not recommended  
by the manufacturer may cause fire, electric shock or injury to persons.  
Avoid the use of an extension cord because the extension cord may overheat and  
cause a risk of fire. However, if you have to use an extension cord, the cord shall be  
14 gauge minimum size and rated not less that 2025 watts. The extension cord must  
be a three wire cord with grounding type plug and cord connector. The extension  
cord shall not be more than 20 feet in length.  
17.  
18.  
SPECIFICATIONS  
Dimensions LxWxH  
10"x6.35"x21.67"  
28.7 lbs  
Net Weight  
Voltage  
110-120V  
60 Hz  
Frequency  
Watts  
1350 W  
Heater Rating  
4600 BTU  
ELECTRICAL CONNECTION  
A 15 Amp, 110 Volt, 60 Hz circuit with a properly grounded outlet is required to operate this  
appliance. The fireplace must be on a dedicated circuit as other appliances on the same  
circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in opera-  
tion. The unit comes standard with a 6.5 ft long 3 wire cord, exiting out the back of the  
fireplace. Plan the installation to avoid the use of an extension cord. If an extension cord  
must be used, it must be a minimum 14 gauge, 3 wire with grounding type plug and  
connector and rated not less than 2025 watts. The extension cord shall not be more than  
20 ft in length.  
WARNING: Electrical outlet wiring must comply with local building codes and other  
applicable regulations to reduce the risk of fire, electrical shock and injury to persons.  
WARNING: Do not use this fireplace if any part of it has become wet. Immediately call a  
qualified service technician to inspect the fireplace and replace any part of the electrical  
system which has been wet.  
 
CLEANING  
Turn heater OFF and unplug from outlet. Use a vacuum or duster to keep heat  
and vent area clean from dust and dirt. The exterior of the stove should be  
cleaned with a damp cloth or duster. Do not use abrasive cleaners, liquid sprays,  
or any other cleaner that may scratch the surface.  
 
SERVICE INSTRUCTIONS  
FOR YOUR SAFETY  
Service must be performed by a qualified service agency.  
REPLACING THE LIGHT BULBS  
This fireplace uses 2 clear 110 Volt, 40 Watt, E-12 socket base light bulbs (small base,  
chandelier candle type bulbs). The access plate is located on the back of the unit. For  
convenience, if one of the light bulbs burns out, it may be easier to replace both of the  
light bulbs at the same time.  
WARNING: Do not exceed 40 Watts per bulb. Use of higher rated bulbs may result in a  
fire, causing property damage, personal injury or loss of life.  
1. Turn off the power to the unit, and unplug it from the electrical outlet.  
2. Let the fireplace cool if it has been operating.  
3. Turn the fireplace so you are facing the back of the fireplace.  
4. Look for the access plate with the gold printing on it.  
5. Remove the 3 screws holding the access plate in position. Once you have removed  
the 3 screws, lift the access plate so the 2 positioning tabs come free of their slots.  
Once you have removed the access plate you can see and access the two 40 watt  
chandelier bulbs.  
6. Remove each light bulb by unscrewing them out of the bases, turning them  
counterclockwise. You can use one hand to hold the light socket in place, if required.  
7. Install the new light bulbs by turning each light bulb into the base clockwise. You can  
use one hand to hold the light socket in place, if required.  
8. Replace the access plate by inserting the 2 tabs, pushing the plate up against the  
fireplace back, and inserting the 3 screws.  
9. Turn the fireplace back so you are facing the front of the fireplace.  
10. Plug the fireplace back into the electrical outlet and turn the power on and enjoy the  
flame effect.  
SERVICE INSTRUCTIONS  
Your fireplace has the following functions:  
On/Off  
Power to the unit  
Please note: Both the low heat  
and the high heat switches must  
be in the on position to achieve  
high heat.  
Low heat  
700 watts  
700  
High heat  
1350  
1350 watts  
 
 

Weider Home Gym WEBE08910 User Manual
West Bend Clock 40053 User Manual
Whirlpool Freezer 33 User Manual
Whirlpool Microwave Oven ACE3411KA2 User Manual
Whirlpool Washer Dryer YLTE6234DQ0 User Manual
Wyse Technology Camera Accessories 022108 User Manual
Zanussi Oven 237504 User Manual
Zanussi Washer Dryer ZWF 12280 W User Manual
Zebra Technologies Printer zebra zxp series 1 User Manual
Zenoah Brush Cutter BC430DWM User Manual