R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
FB25
For Household Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
WEED EATER
1030 Stevens Creek Road
Augusta, GA 30907
545186729 Rev. 1 3/1/09 BRW
SAFETY RULES
D Move at least 10 feet (3 meters) away from
fuel and fueling site before starting engine.
D Always store gasoline in a container ap-
proved for flammable liquids.
WARNING: Failure to follow all
Safety Rules and Precautions can result in
serious injury.
OPERATE YOUR UNIT SAFELY
D Inspect unit before each use for worn,
loose, missing, or damaged parts. Do not
use until unit is in proper working order.
D Keep outside surfaces free from oil and
fuel.
KNOW YOUR UNIT
S Read your instruction manual carefully until
you completely understand and can follow
all warnings and safety rules before operat-
ing the unit.
D Restrict unit to users who understand and
will follow all warnings and safety rules in
this manual.
D Never start or run engine inside a closed
room, building or other unventilated area.
Breathing exhaust fumes can kill.
D To avoid static electricity shock, do not
wear rubber gloves or any other insulated
gloves while operating unit.
D Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc. could be picked up by the air intake and
thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
D Avoid dangerous environments. Do not use
in unventilated areas or where explosive
vapors or carbon monoxide build up could
be present.
D Do not overreach or use from unstable sur-
faces such as ladders, trees, steep slopes,
rooftops, etc. Keep firmfooting and balance
at all times.
WARNING: Inspect the area before
starting the unit. Remove all debris and hard
objects such as rocks, glass, wire, etc. that
can ricochet, be thrown, or otherwise cause
injury or damage during operation.
D Use your unit as a blower for:
D Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
D Blowing grass clippings, straw, or leaves
into piles, around joints, or between bricks.
PLAN AHEAD
D Always wear eye protection when operating,
servicing, or performing maintenance on unit.
Wearing eye protection will help to prevent
rocks or debris from being blown or ricochet-
ing into eyes and face which can result in
blindness and/or serious injury. Eye protec-
tion should be marked ANSI Z87.
D Never place objects inside the blower
tubes; always direct the blowing debris
away frompeople, animals, glass, and solid
objects such as trees, automobiles, walls,
etc. The forceof air can cause rocks, dirt, or
sticks to be thrown or to ricochet which can
hurt people or animals, break glass, or
cause other damage.
D Always wear foot protection. Do not go
barefoot or wear sandals.
D Always wear respirator or face mask when
working with unit in dusty environments.
D Secure hair above shoulder length. Secure
or remove jewelry, loose clothing, or cloth-
ing with loosely hanging straps, ties, tas-
sels, etc. They can be caught in moving
parts.
D Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tube.
D Do not operate unit when you are tired, ill, up-
set, or if you are under the influence of alco-
hol, drugs, or medication.
D Keep children, bystanders, and animals
away from work area a minimum of 30 feet
(10 meters) when starting or operating unit.
Do not point blower nozzle in the direction
of people or pets.
D Check air intake opening and blower tube
frequently, always with engine stopped and
spark plug disconnected. Keep vents and
discharge tubes free from debris which can
accumulate and restrict proper air flow and
cause damage to the unit.
D Never use for spreading chemicals, fertiliz-
ers, or other substances which may contain
toxic materials.
HANDLE FUEL WITH CAUTION, IT IS
HIGHLY FLAMMABLE
D To avoid spreading fire, do not use near leaf
or brush fires, fireplaces, barbecue pits,
ashtrays, etc.
D Eliminate all sources of sparks or flame (in-
cluding smoking, open flames, or work that
cancausesparks) in the areas where fuel is
mixed, poured, or stored.
D Use only for jobs explained in this manual.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Mix and pour fuel in an outdoor area; store
fuel in a cool, dry, well ventilated place; use an
approved, marked container for all fuel pur-
poses.
D Do not smoke while handling fuel or while
operating the unit.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
D Make sure the unit is properly assembled
and in good operating condition.
D Do not fill fuel tank while engine is running.
D Avoid spilling fuel or oil. Wipe up fuel spills be-
fore starting engine.
D Use only recommended WEED EATER
parts; use of any other parts may void your
warranty and cause damage to your unit.
-- 3 --
D Empty the fuel tank before storing the unit.
Use up fuel left in carburetor by starting the
engine and letting it run until it stops.
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An anti- vibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped witha spark arresting screen. If you
operatein alocalewhere such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler beservicedor replacedby your autho-
rized service dealer.
D Do not use any accessory or attachment
other than those recommended by the
manufacturer for use with your unit.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from water heaters, electric mo-
tors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
WARNING: The engine exhaust from
this product contains chemicals known to the
State of California to cause cancer, birth
defects or other reproductive harm.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has beenlinked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
ASSEMBLY
NOTE: It is normal for the fuel filter to rattle in
BLOWER TUBE
the empty fuel tank.
D
Push the blower tube into the blower out-
let until it snaps into place.
ASSEMBLY
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Follow all safety information in the manual
and on the unit.
Blower Outlet
D
No tools are required for assembly.
Blower Tube
-- 4 --
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR
UNIT. Compare the illustrations with your unit to familiarize yourself with locations of the various
controls and adjustments. Save this manual for future reference.
Primer Bulb
Throttle Lever
Fuel Cap
Starter Handle
Blower Tube
Choke
Lever
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
THROTTLE LEVER
The throttle lever is used to select the desired
engine speed and to stop the engine. To stop
engine, move the throttle lever to the STOP
CHOKE LEVER
position and hold until engine stops running.
TheCHOKE helps tosupply fuelto the engine
to aid in cold starting. The RUN position is
used for full speed operation. The HALF
CHOKE position is used for a brief initial
warm-up period.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S Use rakes and brooms to loosen debris be-
fore blowing.
S In dusty conditions, slightly dampen sur-
faces when water is available.
OPERATING
POSITION
Eye Protection
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watch out for children, pets, open windows,
or freshly washed cars. Blow debris away
safely.
S Use the full blower tube extension so the air
stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
OPERATING TIPS
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
-- 5 --
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
STARTING
POSITION
This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline
must be mixed with a good quality synthetic
2-cycle air-cooled engine oil designed to be
mixed at a ratio of 40:1. Poulan/WEED EATER
brand synthetic oil is recommended. Mix gas-
oline and oil at a ratio of 40:1. A 40:1 ratio is
obtained by mixing 3.2 fluid ounces (95 ml) of
oil with 1 gallon(4 liters) of unleaded gasoline.
DO NOT USE automotive oil or boat oil.
These oils will cause engine damage. When
mixing fuel, follow instructions printed oncon-
tainer. Once oil is added to gasoline, shake
container momentarily to assure that the fuel
is thoroughly mixed. Always read and follow
the safety rules relating to fuel before fueling
your unit.
WARNING: When starting engine,
hold the unit as illustrated. Do not set unit on
any surface except a clean, hard area when
starting engine or while engine is running.
Debris such as gravel, sand, dust, grass, etc.
could be picked up by the air intake and
thrown out through the discharge opening,
damaging the unit or property, or causing
serious injury to bystanders or the operator.
CAUTION: Never use straight gasoline in
your unit. This will cause permanent engine
damage and void the limited warranty.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1 -800 -554-6723.
FUEL REQUIREMENTS
This engine requires the use of minimum 87
octane [R+M]/2 clean gasoline.
IMPORTANT
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
Use of alcohol blended fuels (called gasohol or
using ethanol or methanol) can cause major en-
gine performance and durability problems.
1. Slowly press the primer bulb 6 times.
2. Move throttle lever to the START position.
3. Move choke lever to the FULL CHOKE
position.
WARNING: Alternative fuels (not
gasoline) such as E--15 (15% alcohol), E--20
(20% alcohol), E--85 (85% alcohol) are NOT
classified as gasoline and are NOT approved
for use in 2--stroke gasoline engines. Use of
alternative fuels will cause problems such as:
improper clutch engagements, overheating,
vapor lock, power loss, lubrication deficiency,
deterioration of fuel lines, gaskets and internal
carburetor components, etc. Alternative fuels
cause high moisture absorption into the fuel/oil
mixture leading to oil and fuel separation.
Primer Bulb
Throttle Lever
TO STOP THE ENGINE
D To stop the engine, move the throttle lever
Fuel Cap
to the STOP
position and hold until en-
gine stops running.
STARTING YOUR ENGINE
Choke
Lever
WARNING: You MUST make sure
the tube is secure before using the unit.
D Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
D Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
4. Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls.
5. Move choke lever to HALF CHOKE posi-
tion. Pull starter rope sharply until engine
runs.
NOTE: If engine has not started after 5 pulls,
repeat all of the above steps.
6. After a 10 second warm-up, move the
choke lever to the RUN position.
-- 6 --
NOTE: The engine speed can be adjusted
by moving the throttle lever to the left for low
speed or right for high speed.
STARTING A WARM ENGINE
1. Move throttle lever to the START position.
2. Move the choke lever to the HALF
CHOKE position.
3. Pull starter handle sharply until engine
runs.
Throttle Lever
NOTE: If engine does not run after 5 pulls, re-
peat STARTING A COLD ENGINE procedure.
4. After a 10 second warm-up, move the
choke lever to the RUN position.
DIFFICULT STARTING (or starting a
flooded engine)
Flooded engines can be started by placing the
choke lever in the RUN position and the throttle
lever in the START position; then, pull the start-
er handle sharply to clear the engine of excess
fuel. This could require pulling the starter handle
many times depending on how badly the unit is
flooded. If the unit still does not start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
7. To stop engine, move the throttle lever to
the STOP
position and hold until en-
gine stops running.
NOTE: If engine does not stop, move choke
lever to FULL CHOKE.
MAINTENANCE
We recommend all maintenance, service and
adjustments not listed in this manual be per-
formed by an authorized service dealer.
INSPECT AND CLEAN UNIT AND
DECALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit us-
ing a damp cloth with a mild detergent.
S Wipe off unit with a clean dry cloth.
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
CLEAN AIR FILTER
ommended maintenance
described in the instruction
manual performed by an
Air Filter Cover
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, WEED EATER may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
Air Filter
Button
Cleaning the air filter:
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the cover and the area around it to
keep debris from falling into the carbure-
tor chamber when the cover is removed.
2. Press button to open air filter cover. Re-
move air filter.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Throttle Lever -- Ensure throttle lever func-
tions properly by moving the throttle lever to
NOTE: Do not clean filter in gasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
the STOP
position and holding until en-
3. Wash the filter in soap and water.
gine stops running; then restart engine and
continue.
4. Allow filter to dry.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
6. Replace parts.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
-- 7 --
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen and
must be removed to avoid creating a fire haz-
ard or affecting engine performance.
For normal homeowner use, the muffler and
spark arresting screen will not require any
service. After 50 hours of use, we recom-
mend that your muffler be serviced or re-
placed by your authorized service dealer.
REPLACE SPARK PLUG
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder anddis-
card.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
CARBURETOR ADJUSTMENTS
There is no screw for idle adjustment on your
blower. Thethrottle lever is used to control en-
gine speed. The engine speed can be ad-
justed by moving the throttle lever to the left
for low speed or right for high speed. If your
engine will not run properly or you require fur-
ther assistance, contact an authorized ser-
vice dealer or call 1--800--554--6723.
4. Reinstall the spark plug boot.
INSPECT MUFFLER AND SPARK
ARRESTING SCREEN
WARNING: The muffler on this
product contains chemicals known to the
State of California to cause cancer.
STORAGE
HELPFUL TIP
WARNING: Perform the following
steps after each use:
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
S Allow engine to cool, and secure the unit
before storing or transporting.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.If your
unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container. Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
-- 8 --
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
1. Engine flooded.
REMEDY
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
5. Compression low.
1. Fuel not reaching
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Engine will not
idle properly.
carburetor.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
Engine will not
accelerate,
lacks power, or
dies under a
load.
3. Clean or replace spark plug
and re-gap.
3. Spark plug fouled.
4. Contact an authorized service dealer.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Choke partially on.
1. Adjust choke.
Engine smokes
excessively.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
4. Carbon build up.
-- 9 --
LIMITED WARRANTY
WEED EATER, a division of Husqvarna Con-
In Canada, contact:
sumer Outdoor Products N.A., Inc., warrants to
the original consumer purchaser that each new
WEED EATER brand gasoline tool or attach-
ment is free from defects in material and work-
manship and agrees to repair or replace under
this warranty any defective gasoline product or
attachment as follows from the original date of
purchase.
WEED EATER
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by WEED EATER
for this tool. This warranty does not cover tune--
up, spark plugs, filters, starter ropes, or blower
tubes that will wear and require replacement
with reasonable use during the warranty period.
This warranty does not cover pre--delivery set-
up or normal adjustments explained in the in-
struction manual. This warranty does not cover
transportation costs.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTH-
ER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
The policy of WEED EATER is to continuous-
ly improve its products. Therefore, WEED
EATER reserves the right to change, modify,
or discontinue models, designs, specifica-
tions, and accessories of all products at any
time without notice or obligation to any pur-
chaser.
WEED EATER, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
1030 Stevens Creek Road
Augusta, GA 30907
1--800--554--6723
U.S. EPA/CALIFORNIA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and WEED
EATER are pleased to explain the emissions
control system warranty on your year 2009 and
later small off--road engine. In California, all
small off--road engines must be designed, built,
andequippedto meet theState’s stringent anti--
smog standards. WEED EATER must war-
rant the emission control system on your
small off--road engine for the periods of time
listed below provided there has been no
abuse, neglect, or improper maintenance of
your small off--road engine. Your emission
control system includes parts such as the car-
buretor, the ignition system and the fuel tank.
Where a warrantable condition exists, WEED
EATER will repair your small off--road engine
at no cost to you. Expenses covered under
warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions related part on your
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of such an emission related
part, the part will be repaired or replaced by
WEED EATER. OWNER’S WARRANTY RE-
SPONSIBILITIES: As the small off--road en-
gine owner, you are responsible for the per-
formance of the required maintenance listed
in your instruction manual. WEED EATER
recommends that you retain all receipts cov-
ering maintenance on your small off--road en-
gine, but WEED EATER cannot deny warran-
ty solely for the lack of receipts or for your fail-
ure to ensure the performance of all sched-
uled maintenance. As the small off--road en-
gine owner, you should be aware that WEED
EATER may deny you warranty coverage if
your small off--road engine or a part of it has
-- 1 0 --
faileddue to abuse, neglect, improper mainte-
nance, unapproved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsible
for presenting your small off--road engine to an
WEED EATER authorized repair center as
soon as a problem exists. Warranty repairs
should be completed in a reasonable amount of
time, not to exceed 30 days. If you have any
questions regarding your warranty rights and re-
sponsibilities, you should contact your nearest
authorized service center, call WEED EATER at
1--800--554--6723, or send e-mail correspond-
ence to emission.warranty@HCOP--emission.
fective if the diagnostic work is performed at
an approved WEED EATER servicing center.
CONSEQUENTIAL DAMAGES: WEED
EATER may be liable for damages to other
engine components caused by the failure of a
warranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD -ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. WEED EATER is not liable to cover fail-
ures of warranted parts caused by the use of
add--on or modified parts. HOW TO FILE A
CLAIM: If you have any questions regarding
your warranty rights and responsibilities, you
should contact your nearest authorized ser-
vice center, call WEED EATER at
1--800--554--6723, or send e-mail correspon-
com.
WARRANTY
COMMENCEMENT
DATE: The warranty period begins on the date
the small off--road engine is purchased.
LENGTH OF COVERAGE: This warranty shall
be for a period of two years from the initial date
of purchase. WHAT IS COVERED: REPAIR
OR REPLACEMENT OF PARTS. Repair or re-
placement of any warranted part will be per-
formed at no charge to the owner at an ap-
proved WEED EATER servicing center. If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center, call
WEED EATER at 1--800--554--6723, or send
e-mail correspondence to emission.warranty
@HCOP--emission.com. WARRANTY PE-
RIOD: Any warranted part which is not sched-
uled for replacement as required mainte-
nance, or which is scheduled only for regular
inspection to the effect of “repair or replace as
necessary” shall be warranted for 2 years.
Any warranted part which is scheduled for re-
placement as required maintenance shall be
warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is de-
dence
to
emission.warranty@HCOP--
emission.com. WHERE TO GET WARRAN-
TY SERVICE: Warranty services or repairs
shall be provided at allWEED EATER service
centers. Call: 1--800--554--6723 or send
e-mail correspondence to emission.warranty@
HCOP--emission.com. MAINTENANCE, RE-
PLACEMENT AND REPAIR OF EMISSION
RELATED PARTS: Any WEED EATER ap-
proved replacement part used in the perfor-
mance of any warranty maintenance or repair
on emission related parts will be provided
without charge tothe owner if thepart is under
warranty. EMISSION CONTROL WARRAN-
TY PARTS LIST: Carburetor, air filter (covered
up to maintenance schedule), ignition system:
spark plug (covered up to maintenance sched-
ule), ignition module, muffler including catalyst (if
equipped), fuel tank.
MAINTENANCE
STATEMENT: The owner is responsible for
the performance of all required maintenance
as defined in the instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 11 --
|