Waterpik Technologies Outdoor Shower CF 201C User Manual

Installation  
Instructions  
Operation  
Spray Change  
Button  
To change settings, from  
either the full-body spray  
or the concentrated power  
spray, push the button  
atthe base of the  
showerhead so it extends  
to the opposite side of its  
current position. (It will  
move horizontally to the  
showerhead.)  
Your new showerhead will fit a standard 1/2 ” shower arm. Do not  
attach this product to a plastic shower arm since it may not  
provide adequate support.  
Tools are not required. Do not use pipe tape or any other  
sealants when installing the showerhead. These materials are not  
necessary and may cause the nut to loosen prematurely. Hand  
tightening is sufficient to secure the shower thread. Make sure  
the washer is in the end of the nut.  
Spray Change  
Button  
1. Remove old showerhead. Clean pipe threads thoroughly.  
Spray  
Change  
Button  
2. Attach the flexible shower arm collar to the showerhead, being  
careful to align the threads of the showerhead to the threads  
of the flexible shower arm.  
Care and Cleaning  
Instructions  
Shower  
Arm Nut  
Collar  
Clean the filter screen at least once a year, or whenever you  
notice a drop in water pressure. To remove, unscrew the nut  
from the pipe. Remove screen by turning it counter-clockwise  
(pliers may be used) and rinse. The white flow restrictor  
beneath filter screen is also removable for cleaning. Tip the  
nut and the flow restrictor will fall out. Flow restrictor must be  
reinstalled with pointed end facing in. Reinstall filter screen  
and rubber washer.  
Flexible Arm  
Spray  
Change  
Button  
Cleaning is required when mineral deposits appear on the  
Bracket  
spray orifices to maintain proper working conditions.  
Clean the flexible nozzles by rubbing with a finger or soft  
bristled toothbrush.  
Soaking and cleaning with household vinegar will help  
remove mineral build up.  
Do not clean or rinse any part with harsh chemicals, heavy  
duty cleaners or abrasives. This may damage parts or  
finish and may void warranty.  
3. Straighten the flexible shower arm before trying to screw onto  
the shower pipe. Again, take care in aligning the nut to the  
shower pipe so you do not cross threads.  
Adapter  
4. While installing, support the shower
hold onto the nut rather than the co
Turn only the nut to tighten. Do not t
the flexible shower arm covering  
5 foot hose  
during installation. (This could  
damage the covering and/or  
Limited Lifetime  
Warranty  
Instruction Manual  
cause the product to malfunction.)  
Models CF-201(C), CF-261(C)  
5. Tighten the shower nut onto the pip
securely by hand. Do not over tighte
or use pliers.  
6. Slowly turn on cold water and check for leaks. If leaks occur,  
re-tighten all connections.  
7. Do not use excessive force in positioning the showerhead  
and/or arm.  
8. If the showerhead is not maintaining its position, re-tighten the  
showered and shower arm nuts.  
Water Pik, Inc. warrants to the original purchaser of this product  
that it is free from defects in material and workmanship for as long  
as the original purchaser owns the product. Water Pik will at our  
election, replace any part of the product which in our opinion is  
defective, provided that the product has not been abused,  
misused, altered or damaged after purchase. (This includes  
damage due to use of tools or harsh chemicals). In the event an  
item qualifying for warranty action has been discontinued, we will  
replace it with what we deem to be the closest available product.  
Water Pik is not responsible for labour charges, installation or other  
consequential costs. The responsibility of Water Pik shall not  
exceed the original purchase price of the product. Save your  
receipt as proof of purchase is required for warranty action.  
Flow Control  
Filter Screen  
Washer  
Flow Regulator  
with O-ring  
(black O-ring  
faces out)  
9.5L per minute maximum  
flow is limited by the flow  
restrictor. For low water  
pressure areas, flow  
restrictor may be removed.  
To remove, unscrew filter  
screen by turning counter-  
clockwise. Tip pivot ball  
assembly and flow control  
will fall out for cleaning or  
removal.  
Showerhead  
Nut  
Hand-Held  
Installation  
1. Remove old showerhead. Clean pipe threads thoroughly.  
2. Slightly loosen swivel collar on bracket.  
3. Hand tighten pivot ball to pipe.  
4. Hand tighten adaptor to showerhead.  
5. Hand tighten hose to adapter and bracket.  
6. Place showerhead in bracket.  
This product is covered by one or more of the following patents. U.S.: 4,674,687;  
5,316,216; 5,449,206(Lic); 5,865,378; 5,997,047(Lic); 6,164,569; 6,164,570; 6,230,989;  
6,454,186; 6,626,210; 6,629,651; 6,641,057; 6,739,523; 6,758,826; 7,066,411B2;  
7,111,798B2; 7,144,666B2; D406,636; D415,247; D418,902; D418,903; D422,053;  
D422,336; D427,661; D440,641; D450,805; D450,806; D450,807; D451,169; D451,170;  
D451,171; D451,172; D451,583; D451,980; D452,553; D452,725; D452,897; D453,370;  
D453,551; D457,937; D485,887; D490,498; D527,440S; D528,631S; D529,151S;  
D533,253S; D577,099S; D577,793S; D581,014S; D590,048S; Canadian: 94868; 94871;  
96859; 96860; 96861; 96862; 96863; 96864; 96865; 96866; 96867; 96891; 96892;  
96893; 96894; 96895; 96896; 2,277,060; Mexico: 15037; 186852; 218192;  
Germany: 40105034.3; 40502480; M9706460.2; U.K.: 3,021,116; 3,021,863; 3,021,864;  
E.U.: 000341706-0001; 000341706-0002; 000341706-0003; France: 013345;  
Switzerland: 128049; China: ZL98802624.4; 93120174.8; ZL200530004083.3;  
Hong Kong: 1003339; South Korea: 389207; Australia: 726023; Singapore: 44333;  
Japan: 1230114; Additional: 00601962 (Belgium, Switzerland, Germany, France, United  
Kingdom, Italy, Luxembourg, The Netherlands).  
Filter  
Screen  
Flow Regulator  
Cascadia® is a trademark of Water Pik, Inc. registered in Canada, EU, Switzerland, and the  
United States.  
Waterpik® is a trademark of Water Pik, Inc. registered in Argentina, Australia, Austria, Canada,  
China, Czech Republic, Hungary, India, Japan, Poland, Russian Federation, South Africa,  
Switzerland, Ukraine, and the United States.  
Waterpik® (stylized) is a trademark of Water Pik, Inc. registered in Canada, EU, Mexico,  
Switzerland, and the United States.  
© 2009 Water Pik, Inc.  
Have any questions or need assistance?  
Call our toll-free Customer Service Line:  
Water Pik, Inc.  
Printed in China  
888-226-3042  
8:00 a.m. to 4:00 p.m. MT, Monday-Friday  
FN 20007766-F AB  
Showerhead made in China  
DATE: 27 May 2009  
CLIENT: Water Pik, Inc.  
FILENAME: FN20007766-F_AB_CascadiaInst.indd  
FILE TYPE: Adobe InDesign CS4  
SIZE FLAT: 8-1/2” x 8-1/2”  
DESCRIPTION: Cascadia Showerhead Instruction Manual - Canada  
PREPARED BY: Brian Colon  
SIZE FOLDED: 3-5/8” x 4-1/4”  
INK: Black  
FORM: 20007766-F AB  
FOLDS: Vertical trifold, Horiz bifold  
DIELINE: N/A  
 
NOTES:  

Thermo Products Furnace L33 37 39 User Manual
Timex Heart Rate Monitor 579 095002 EU User Manual
Trane Video Game Controller CNT APG002 EN User Manual
Troy Bilt Lawn Mower 769 10459 User Manual
Tunturi Rowing Machine R25 User Manual
Vantec Computer Hardware UGT IS100R User Manual
Verizon Cell Phone CDM7076 User Manual
Vivitar Digital Camera X327 User Manual
Vizio Universal Remote VUR5 User Manual
Weber Griddle 55556 User Manual