Wagner SprayTech Power Roller Cordless Power Roller User Manual

R
Cordless Power Roller  
Owner’s Manual  
Gude d’utilisation • Manual del propietario  
uick-start  
Easy does it from setup to cleanup:  
1
2
3
4
Install the batteries  
Insérer les piles  
Instalar las pilas  
Attach the strap  
Fixer la bandoulière  
Conectar la correa  
Remove the drive housing  
Enlever du logement du mécanisme Fixation des tuyaux flexibles  
Extraer el mecanismo impulsor Conectar las mangeras  
Attach the hoses  
5
6
7
8
Fill the fluid tank  
Remplir le réservoir à liquides  
Llenar el depósito de fluidos  
Attach the drive housing  
Fixation du logement du mécanisme Appuyer sur le bouton marche/arrêt  
Conectar el mecanismo impulsor  
Press the on/off switch  
Apply paint  
Appliquer la peinture  
Aplicar pintura  
Oprimir el botón de encendido  
/ apagado  
9
Cleanup  
Nettoyage  
Limpieza  
Need help? Call us first for answers fast.  
Read this manual for complete instructions.  
Call Wagner toll-free if you have any comments  
or problems with this Wagner product.  
Ce manuel contient les instructions  
complètes.  
1-800-328-8251  
Wagner Technical Service  
Lea este manual para obtener instrucciones  
completas.  
Weekdays: 8:00 - 4:30 Central time  
Weekends: 9:00 - 4:00 Central time  
1770 Fernbrook Lane, Minneapolis, MN 55447  
Form No. 0156934C  
9709  
Español Français English  
 
Checking the Inlet Valve  
If the unit is new or has been stored for an extended period of time  
the inlet ball can become stuck and the pump may be difficult to  
prime. To check:  
Installing the Batteries and Attaching the Strap  
Inlet Ball  
1. Open the battery  
1. Turn the valve body  
Retainer  
+
door. The battery  
-
counterclockwise and pull  
Ball  
-
+
door is located on  
the drive housing.  
-
+
-
down to remove.  
+
Inlet Ball  
Holder  
2. Shake the inlet valve  
assembly gently. If it does  
not rattle, remove the inlet  
ball retainer and clean the  
ball.  
Inlet Valve  
Assembly  
2. Insert the batteries  
in the proper  
direction.  
3. Reassemble the inlet valve.  
1. Place the drive housing on the fluid tank at a 90° angle.  
2. Remove the fluid tank cap  
and fill the tank with paint.  
CAUTION  
Improper installation of batteries may cause batteries to  
overheat and leak acid. Acid may cause severe injury and/or  
property damage.  
3. Wipe the lip, threads, and  
body of the fluid tank to  
remove any spilled or  
splattered material.  
4. Replace the cap and lock the  
drive housing securely onto  
the fluid tank.  
NOTE: Use high quality alkaline batteries only.  
3. Attach the strap to the loops on the drive housing.  
The On/Off switch has two speeds for  
controlling the paint flow – High and  
Low. Choose the setting which is  
appropriate for your application. If too  
much paint is being delivered to the  
roller on High speed, use the Low  
speed setting. If paint flow is still too  
great, shut the roller off, then turn back  
on when more paint is needed.  
Begin rolling as paint appears to saturate the roller cover. If paint is  
flowing faster than you can roll,turn the pump off until more paint is  
needed.  
the Fluid Tank  
Open  
NOTE: Do not place the roller below the level of the paint when  
not in use. Paint will siphon to roller even if motor and  
pump are turned off.  
Close  
1. Remove the drive housing by  
turning the drive housing  
counterclockwise.  
2. Attach the drive housing by  
setting it onto the fluid tank at  
a 90° angle and turning  
clockwise.  
1. Slide the fluid hose through  
the anti-kinking spring and  
the spring clip.  
2. Push the fluid hose to the  
port on the side of the  
drive housing.  
Fluid Hose  
3. Slide the spring clip over  
the fitting to keep the hose  
securely in place.  
4. Slide the anti-kinking  
spring up against spring  
clip.  
R
©1997 Wagner Spray Tech. All rights reserved.  
3
English  
 
       
A thorough cleaning after each use of the roller is important to keep  
it in good working order.  
Cleaning the Roller Cover  
1. Pull one end of the splatter  
shield out of the end cap and  
slip opposite end off of the  
roller handle.  
2. Press the locking tab and  
remove the roller cover and  
roller core.  
NOTE: When using latex paint, use warm soapy water for  
cleaning parts. When using oil paint, the appropriate  
solvent is often mineral spirits. Always follow the paint  
manufacturer's recommendations for appropriate solvent.  
Not recommended for lacquer and other hard solvents.  
Tab  
End Cap  
Core  
Cover  
3. Unscrew the end cap and  
slide the roller cover off of the  
roller core.  
Shield  
CAUTION  
Do not turn the roller upside down or on its side. If liquid gets  
inside the drive housing it could damage the unit.  
4. Clean the roller cover with the appropriate solvent.  
NOTE: For latex, clean roller cover, core and end cap  
thoroughly in warm soapy water.  
The following steps outline the basic cleanup procedures. For more  
detailed instructions on how to perform each step, refer to the  
Detailed Cleanup section in this manual.  
For oil-based paints, clean roller cover, core and end  
cap in the appropriate solvent recommended by the  
paint manufacturer.  
Removing Paint from the Hose and Container  
1. Remove the drive housing  
from fluid container.  
2. Hold the roller handle over  
the paint pail and run the  
1
2
pump to remove excess  
paint from hose and pump.  
3. Pour remaining paint from  
container back into paint pail.  
1. Clean the roller cover.  
2. Remove paint in hose.  
Cleaning the Hose  
Thoroughly  
3
For Latex:  
1. Remove the hose from the motor  
compartment.  
2. Insert the hard plastic tube of the  
faucet adapter into the paint hose.  
3. Empty fluid tank.  
4. Clean hose.  
3. Push the adaptor over a faucet.  
4. Slowly increase the water pressure  
and run water through the hose and  
handle until the water come out clean.  
For Oil:  
1. Fill the paint container with the appropriate solvent  
recommended by the paint manuafacturer.  
2. Circulate the solvent through hose and roller arm for several  
minutes.  
5. Clean roller handle.  
6. Remove the pump assembly.  
Cleaning the Roller Handle Assembly  
1. Remove the seal from the end of the  
roller handle. Note the direction of the  
lip for correct replacement.  
2. Clean the handle and seal thoroughly.  
3. Apply a thin layer of petroleum jelly to  
the seal.  
7. Remove and clean the valves. 8. Clean the pump assembly.  
4. Replace the seal in the proper direction.  
Removing the Pump from the Drive Housing  
1. Turn the retaining nut on the pump  
counterclockwise.  
2. Pull out the pump assembly.  
NOTE: The piston will remain  
attached.  
9. Clean and lubricate the  
piston and O-ring.  
10. Reassemble the pump and  
attach it to the drive housing.  
3. Wipe excess paint off of the piston.  
4. Apply a thin layer of petroleum jelly to the pump O-Ring.  
R
4
©1997 Wagner Spray Tech. All rights reserved.  
English  
 
 
Cleaning the Pump Housing  
NOTE: Remove the pump carefully or the piston may come off.  
If the piston comes off, reassemble by sliding piston  
onto the brass piston connecting rod.  
1. Clean pump housing with warm,  
soapy water or the appropriate  
solvent using the brush supplied.  
2. Apply a thin layer of petroleum  
jelly to the pump O-Ring.  
NOTE: Wipe excess paint off the drive housing with an  
appropriate solvent. DO NOT IMMERSE UNIT IN  
SOLVENT OR OTHER LIQUID.  
NOTE: Be sure to clean all  
small parts  
Cleaning the Valves  
thoroughly. Paint will  
act as an adhesive  
when dry.  
Cleaning the Inlet Valve  
1. Press down on the locking  
tab and pull the valve  
assembly out.  
2. Turn valve body  
counterclockwise and remove.  
3. Remove the ball retainer and  
inlet ball.  
4. Remove the filter basket and  
thoroughly clean all parts in  
warm, soapy water or the  
appropriate solvent.  
CAUTION  
Clean, dry, and lubricate the system thoroughly before storing.  
Do not store with liquids inside unit. Storing the unit in cold  
temperatures can cause the liquids to freeze and expand,  
causing pressure to build and break parts. Let the equipment  
come up to room temperature before operating.  
Cleaning the Outlet Valve  
1. Turn valve cap assembly counter  
clockwise remove.  
2. Clean all parts in warm, soapy  
water or the appropriate solvent.  
When storing the roller for more than a day, take the following  
precautions:  
1. Remove the batteries.  
2. Remove the hose from the pump fitting.  
3. Store the hose in a large loop. If it is bent, it could be damaged.  
Problem  
Cause  
Solution  
The pump will not run.  
There is little or no power.  
The batteries are not in properly.  
Put in new high quality alkaline batteries.  
Put the batteries in properly.  
The pump on/off button was not pressed.  
The pump has seized up.  
Press and release the pump on/off button.  
Clean the piston and pump housing.  
The motor and piston run but  
there is little or no fluid flow.  
The batteries are low.  
Put in new high quality alkaline batteries.  
Tighten the fluid hose securely.  
The fluid hose is leaking.  
The inlet, outlet, or relief valves are dirty.  
The fluid in the fluid tank is low.  
The piston O-ring is worn.  
Clean the inlet and outlet valves.  
Fill the fluid tank.  
Replace the piston O-ring.  
The piston has slipped off the brass axle.  
The seal is not in place.  
Snap the piston back on the axle  
Check and place the seal properly.  
Press and release the pump on/off button to turn the  
the pump off until more paint is needed.  
Remove the seal, lubricate and replace.  
Paint leaks from the roller core.  
Roller cover slides on the wall.  
Too much paint pumped to roller.  
The seal is not lubricated.  
Have you tried the recommendations above and are still having problems? In the United States, call our toll-free  
consumer service at 1-800-328-8251 Monday through Friday between 8:00 AM and 4:30 PM Central time or between 9:00  
AM and 4:00 PM Saturday or Sunday, or contact an authorized service center.  
R
©1997 Wagner Spray Tech. All rights reserved.  
5
English  
 
 
Wagner One Year Limited Warranty - Keep on file - English  
This product manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in  
material and workmanship for one year from date of purchase if operated in accordance with Wagner's printed recommendations and  
instructions. This product is designed for home use only. If this product is used for professional/rental purposes, this warranty applies only for  
30 days from date of purchase.  
This warranty does not cover damage resulting from improper use, accidents, user's negligence or normal wear. This warranty does not  
cover defects or damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center. This warranty  
does not apply to accessories.  
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IS LIMITED TO ONE YEAR FOR  
HOME USE AND 30 DAYS FOR PROFESSIONAL/RENTAL USE FROM DATE OF PURCHASE.  
WAGNER SHALL NOT IN ANY EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER  
FOR BREACH OF THIS WARRANTY OR ANY OTHER REASON.  
If any product is defective in material and/or workmanship during the applicable warranty period, return it with proof of purchase,  
transportation prepaid to any Wagner Authorized Service Center. Contact Wagner Technical Service at 1770 Fernbrook Lane, Minneapolis,  
MN 55447 or telephone 1-800-760-3844 for authorized service center locations. Wagner's Authorized Service Center will either repair or  
replace the product (at Wagner's option) and return it to you, postage prepaid.  
Some states do not allow limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the  
above limitation and exclusion may not apply to you.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
Garantie limitée d’une année de la société Wagner – GARDEZ DANS VOS DOSSIERS – Français  
Ce produit, fabriqué par la société Wagner Spray Tech (« Wagner »), est garanti au premier acheteur au détail contre toute défectuosité de  
matériau ou d’exécution, pour une période d’une année à compter de la date d’achat, pourvu que l’on se serve du produit en suivant les  
recommandations et consignes écrites de Wagner. Ce produit est destiné à l’usage domestique seulement. Si on l’utilise pour des fins  
professionnelles ou pour la location, la présente garantie ne s’applique que pendant une période de 30 jours à compter de la date d’achat.  
La présente garantie ne s’applique pas aux dégâts entraînés par une utilisation incorrecte, par un accident, par la négligence de l’usager ou  
par l’usure normale. La présente garantie ne s’applique non plus aux défectuosités ou dommages résultant de l’entretien ou de la réparation  
que fait une personne quelconque qui ne soit pas membre d’un centre d’entretien agréé de Wagner. La présente garantie ne s’applique pas  
aux accessoires.  
TOUTE GARANTIE IMPLICITE DE QUALITÉ MARCHANDE OU D’ADAPTATION À UN USAGE PARTICULIER EST LIMITÉE À UNE  
PÉRIODE D’UNE ANNÉE POUR L’UTILISATION DOMESTIQUE ET DE 30 JOURS POUR UNE UTILISATION PROFESSIONNELLE OU DE  
LOCATION, À COMPTER DE LA DATE D’ACHAT.  
WAGNER NE SERA EN AUCUN CAS RESPONSABLE DE DOMMAGES ACCESSOIRES OU INDIRECTS DE QUELQUE NATURE QUE CE  
SOIT, À LA SUITE D’UNE INOBSERVATION DE LA PRÉSENTE GARANTIE OU POUR UNE AUTRE RAISON QUELCONQUE.  
Si un produit est défectueux en ce qui concerne les matériaux ou l’exécution pendant la période de garantie applicable, vous devez le  
retourner, avec une preuve d’achat et frais de port payés, à n’importe quel centre d’entretien agréé de Wagner. Pour connaître l’emplacement  
des centres d’entretien agréés de la société, communiquez avec le service technique de Wagner au 1770 Fernbrook Lane, Minneapolis, MN  
55447 USA, ou téléphonez au 1-800-760-3844. Le centre d’entretien agréé de Wagner réparera ou remplacera le produit (à la discrétion de  
Wagner) et vous le retournera par la poste, avec frais de port payés.  
Certaines provinces interdisent les restrictions sur la durée d’une garantie implicite ou l’exclusion des dommages accessoires ou indirects. Il  
se peut donc que la restriction et l’exclusion énoncées ci-dessus ne s’appliquent pas à vous.  
Le présente garantie vous accorde des droits juridiques spécifiques, et vous avez peut-être d’autres droits, qui peuvent varier d’une province  
à l’autre.  
Garantía limitada de un año de Wagner – MANTENGALA ARCHIVADA – Español  
Este producto fabricado por Wagner Spray Tech Corporation (Wagner) es garantizado al comprador original al por menor contra defectos en  
el material y la mano de obra por un año a partir de la fecha de compra si se opera siguiendo las recomendaciones e instrucciones impresas  
de Wagner. Este producto ha sido diseñado solamente para uso doméstico. Si se usa para propósitos profesionales o de alquiler, esta  
garantía se aplica solamente por 30 días a partir de la fecha de compra.  
Esta garantía no cubre daños que resulten del uso inadecuado, accidentes, negligencia del usuario o desgaste normal. Esta garantía no  
cubre defectos ni daños causados en mantenimiento o reparaciones realizados por alguien que no sea un Centro de Servicio Autorizado por  
Wagner. Esta garantía no se aplica a los accesorios.  
TODA GARANTIA IMPLICITA DE COMERCIABILIDAD O APTITUD PARA UN PROPOSITO PARTICULAR ESTA LIMITADA A UN AÑO PARA  
USO DOMESTICO Y A TREINTA DIAS PARA USO PROFESIONAL O DE ALQUILER A PARTIR DE LA FECHA DE COMPRA.  
WAGNER NO SERA RESPONSABLE BAJO NINGUNA CIRCUNSTANCIA POR NINGUN DAÑO INCIDENTAL O INDIRECTO DE NINGUNA  
CLASE, YA SEA POR VIOLACION DE ESTA GARANTIA O CUALQUIER OTRA RAZON.  
Si cualquier producto resulta defectuoso en sus materiales y/o mano de obra durante el periodo de garantía aplicado, devuélvalo con el  
comprobante de compra, flete pagado anticipadamente, a cualquier Centro de Servicio Autorizado por Wagner. Póngase en contacto con el  
Departamento de Servicio Técnico de Wagner en 1770 Fernbrook Lane, Minneapolis, MN 55447 o llame por teléfono al  
1-800-760-3844 para averiguar las ubicaciones de los Centros de Servicio Autorizados. El Centro de Servicio Autorizado de Wagner  
reparará o cambiará el producto (a criterio de Wagner) y se lo devolverá a usted con el porte pagado anticipadamente.  
Algunos estados no permiten limitaciones a la duración de una garantía implícita ni la exclusión de daños incidentales o indirectos, de modo  
que la limitación y exclusión anteriores puede que no se apliquen a usted.  
Esta garantía le da a usted derechos legales específicos y usted podría tener también otros derechos que varían de un estado a otro.  
R
16  
©1997 Wagner Spray Tech. All rights reserved.  
 

Technicolor Thomson CRT Television 2 5 D G 1 6 E T User Manual
Toshiba Projector TLP XC2000 User Manual
TRENDnet Computer Drive TU2 PCLINK User Manual
Uniden Headphones EXT 176 User Manual
Uniden Two Way Radio FRS500 User Manual
Univex Mixer RBM User Manual
Vermont Casting Gas Grill VM400 User Manual
ViewSonic Computer Monitor A90F+ User Manual
Vivitar Camcorder Accessories Tripod Video Equipment User Manual
Weber Gas Grill 2000 LX Series User Manual