Vizio Universal Remote XRU9M User Manual

 
XRU9M OM 2-6-10.indd 1  
2/6/2010 1:51:35 PM  
Button Descriptions  
Button Descriptions, cont.  
P.SIZE – Repeatedly press this button to set the size of  
the PIP screen to small, medium, or large.  
P.INPUT – Press the button to choose the input source  
for the PIP screen.  
P.CH – Press this button to change the channels in the  
PIP screen when TV is selected as PIP input.  
WIDE – This button cycles through the available screen  
formats.  
FREEZE – Press this button to “Freeze-Frame” the  
current screen. Press this button again to continue.  
MTS – This button will select the MTS options of Stereo,  
SAP, Mono or alternate audio channels, where available.  
SWAP – While in PIP mode; pressing SWAP will switch  
the displays from the main screen to the sub-screen or  
vice versa.  
MODE – Use this button to change the picture.  
INFO – This button displays the image and system  
information display.  
P.AUDIO – Press this button to switch the audio from the  
main screen to the sub-screen while in PIP mode.  
CC – This button will select the Closed Caption mode.  
DVD – This button selects a programmed DVD player.  
AUDIO – This button selects a programmed Audio  
Receiver/Amp/Home Theater System.  
CABLE – This button selects a programmed cable TV  
set-top box or a satellite TV set-top box.  
TV – This button selects a programmed TV.  
Note: the remote is pre-programmed to operate VIZIO  
TVs by default.  
MENU – Use this button for the on-screen menu.  
EXIT – Press this button to exit from the on-screen  
menu.  
OK – Use this button for the on-screen menu. Press it to  
conrm or choose a highlighted menu selection.  
Up, Down, Left, Right – These buttons are used to  
navigate the on-screen menu.  
GUIDE – This button displays program guide  
information.  
LAST – This button recalls the previously viewed  
channel.  
MEDIA – Press this button to view pictures, listen to  
music, or watch movies on a USB drive connected to the  
Multi Media port on the side of a VIZIO HDTV.  
VOL +/- – This button turns the volume up or down.  
CH +/- – This button changes the channels up or down.  
MUTE – This button turns the sound on and off.  
NUMBER BUTTON PAD – Use these buttons to select  
a channel.  
INPUT – This button allows the user to cycle through the  
available source inputs.  
- (DASH) – When selecting a digital channel directly,  
use this button between the main and sub-channels. For  
example, channel 28-2 would be selected by the button  
sequence 2, 8, DASH, 2.  
POWER – Press this button to turn the component on or  
off.  
SET – This button starts all programming of the Remote  
Control.  
HDMI – Press this button to select the HDMI input. By  
pressing it repeatedly you will go through all HDMI inputs  
in sequence.  
COMP – Press this button to select Component input.  
AV – Press this button to select AV (either Composite or  
S-Video) input.  
DTV – Press this button to select TV input.  
PIP – Pressing this button will activate the picture-in-  
picture feature.  
4
5
XRU9M OM 2-6-10.indd 4-5  
2/6/2010 1:51:43 PM  
 
Initial Setup  
Setup  
Insertion of Batteries in the Remote Control  
Programming for BLU-RAY or DVD  
1. Manually turn on your DVD player.  
2. Press the DVD button on the remote control.  
3. Press and hold the SET button until the LED  
LIGHT ashes twice.  
4. Find the programming code for your DVD  
player in the code list (on separate sheet) and  
enter it using the Number Buttons. If the code  
is accepted, the LED ashes twice after the last  
digit is entered.  
Insert two AAA batteries  
into the remote control.  
Make sure that you  
match the (+) and (-)  
symbols on the batteries  
with the (+) and (-)  
symbols inside the  
battery compartment. Re-  
attach the battery cover.  
If the LED does not ash twice, repeat Steps  
2 through 4 with the next code listed for the  
component and manufacturer.  
Precautionary Tips for Inserting the Batteries  
• Only use AAA batteries.  
5. Point the remote control at the DVD player and  
press the POWER button. The DVD player  
should turn off.  
• Do not mix new and old batteries. This may  
result in cracking or leakage that may pose a  
re risk or lead to personal injury.  
Note:  
• Inserting the batteries incorrectly may also result  
in cracking or leakage that may pose a re risk  
or lead to personal injury.  
If your DVD player does not respond, try all the  
codes for your DVD player brand. If the codes  
do not work, or your brand is not listed, see  
“Searching for Component Codes, page 11.”  
Sometimes a code listed will only include limited  
functions. Try other codes that may include  
more functionality.  
• Dispose of the batteries in accordance with local  
laws and regulations.  
• Keep the batteries away from children and pets.  
Battery Saver  
Your remote automatically turns off if the buttons  
are depressed more than 30 seconds.  
Code Saver  
You will have up to 10 minutes to change the  
batteries in your remote without losing codes you  
have programmed. However, to avoid losing your  
codes, do not press any buttons until batteries are  
installed in the remote.  
6
7
XRU9M OM 2-6-10.indd 6-7  
2/6/2010 1:51:43 PM  
 
Setup, cont.  
Setup, cont.  
Programming for AUDIO  
Programming for CABLE or SATELLITE  
1. Manually turn on your AUDIO device.  
2. Press the AUDIO button on the remote control.  
3. Press and hold the SET button until the LED  
LIGHT ashes twice.  
1. Manually turn on your CABLE box.  
2. Press the CABLE button on the remote control.  
3. Press and hold the SET button until the LED  
LIGHT ashes twice.  
4. Find the programming code for your AUDIO  
device in the code list (on separate sheet) and  
enter it using the Number Buttons. If the code  
is accepted, the LED ashes twice after the last  
digit is entered.  
4. Find the programming code for your CABLE  
box in the code list (on separate sheet) and  
enter it using the Number Buttons. If the code  
is accepted, the LED ashes twice after the last  
digit is entered.  
If the LED does not ash twice, repeat Steps  
2 through 4 with the next code listed for the  
component and manufacturer.  
If the LED does not ash twice, repeat Steps  
2 through 4 with the next code listed for the  
component and manufacturer.  
5. Point the remote control at the AUDIO device  
and press the POWER button. The AUDIO  
device should turn off.  
5. Point the remote control at the CABLE box and  
press the POWER button. The CABLE box  
should turn off.  
Note:  
Note:  
If your AUDIO device does not respond, try all  
the codes for your AUDIO device brand. If the  
codes do not work, or your brand is not listed,  
see “Searching for Component Codes, page  
11.”  
Sometimes a code listed will only include limited  
functions. Try other codes that may include  
more functionality.  
If your CABLE or SATELLITE box does not  
respond, try all the codes for your CABLE or  
SATELLITE box brand. If the codes do not  
work, or your brand is not listed, see “Searching  
for Component Codes, page 11.”  
Sometimes a code listed will only include limited  
functions. Try other codes that may include  
more functionality.  
8
9
XRU9M OM 2-6-10.indd 8-9  
2/6/2010 1:51:43 PM  
 
Setup, cont.  
Setup, cont.  
Programming for TV  
Searching for Component Codes  
Note: The remote is pre-programmed to  
operate VIZIO TVs by default.  
If you cannot nd the manufacturer in the  
component list or the program code does not work,  
you can use the remote control to search for the  
correct component code.  
1. Manually turn on your TV.  
2. Press the TV button on the remote control.  
3. Press and hold the SET button until the LED  
LIGHT ashes twice.  
To search for a component code:  
4. Find the programming code for your TV in the  
code list (on separate sheet) and enter it using  
the Number Buttons. If the code is accepted,  
the LED ashes twice after the last digit is  
entered.  
1. Turn on the component.  
2. Press the matching component button on the  
remote control (DVD, AUDIO, CABLE, or TV).  
3. Press and hold the SET button until the LED  
ashes twice.  
If the LED does not ash twice, repeat Steps  
2 through 4 with the next code listed for the  
component and manufacturer.  
4. Press 9 9 1. The LED ashes twice.  
5. Point the remote control at the component and  
then press and hold the POWER button until  
the component turns off. Release the POWER  
button. If the component does not respond  
correctly, repeat the search procedure to nd  
another code.  
5. Point the remote control at the TV and press the  
POWER button. The TV should turn off.  
Note:  
Reset Remote to Factory Settings:  
Your VIZIO remote uses code 1000 (Default), to  
work your LCD HDTV.  
If your TV does not respond, try all the codes  
for your TV brand. If the codes do not work,  
or your brand is not listed, see “Searching for  
Component Codes, page 11.”  
1. Press and hold SET until the LED ashes twice.  
2. Press 9 1 9 1 9. The LED ashes twice.  
Sometimes a code listed will only include limited  
functions. Try other codes that may include  
more functionality.  
Write your codes down here for easy reference  
later.  
Type  
DVD  
Type Stored  
Code  
AUDIO  
CABLE  
TV  
10  
11  
XRU9M OM 2-6-10.indd 10-11  
2/6/2010 1:51:44 PM  
 
Maintenance & Troubleshooting  
VIZIO Remote Control Precautions  
2. The remote control is not working with my  
devices.  
The remote control should be kept dry and away  
from heat sources. Avoid humidity.  
o Move closer to the device.  
o Point the remote control directly at the  
remote sensor on your device.  
o Remove any obstacles between the remote  
control and the remote sensor.  
o Replace dead batteries with new ones.  
o Make sure you have pressed the correct  
device button at the top of the remote.  
If the Component responds erratically to the  
remote control or does not respond at all, check  
the batteries. If the batteries are low or exhausted,  
replace them with fresh batteries.  
When not using the remote control for a long  
period of time, remove the batteries.  
3. The remote control does not work with my  
device even after programming it.  
Do not take the batteries apart, heat them, or throw  
them into a re.  
o Set the remote control code correctly. If the  
code that is listed rst for your device does  
not work, try all the codes for your device  
in the order in which they are listed in the  
supplied Code List.  
Do not subject the remote control to undue  
physical stress, such as striking or dropping it.  
Cleaning the Remote Control  
Telephone & Technical Support  
1. Use a soft cloth for cleaning.  
2. If the remote control is seriously contaminated,  
use a soft cloth moistened with diluted neutral  
cleaner to clean the display. Wring water out of  
the cloth before cleaning to prevent water from  
penetrating into the housing.  
Products are often returned due to a technical  
problem rather than a defective product that may  
result in unnecessary shipping charges billed  
to you. Our trained support personnel can often  
resolve the problem over the phone. For more  
information on warranty service or repair, after  
the warranty period, please contact our Support  
Department at the number below. Customer  
support and quality service are integral parts of  
VIZIO’s commitment to service excellence.  
Troubleshooting  
1. Remote control does not work:  
o Point the remote control directly at the  
remote sensor on your TV.  
o Remove any obstacles between the remote  
control and the remote sensor.  
o Replace dead batteries with new ones.  
o Press the DTV button on the top of the  
remote to return to the TV mode.  
For technical assistance contact our VIZIO  
Technical Support Department via email or phone.  
Email: [email protected] (877) 698-4946  
Fax: (949) 585-9563 Hours of operation: Monday -  
Friday: 6 am to 9 pm Saturday – Sunday: 8 am to  
4 pm Please have your VIZIO model number, and  
date of purchase available before you call VIZIO.  
VIZIO  
39 Tesla  
Irvine, CA 92618, USA  
Telephone: (949) 428-2525 Fax: 949-585-9514  
12  
13  
XRU9M OM 2-6-10.indd 12-13  
2/6/2010 1:51:44 PM  
 
ONE YEAR LIMITED WARRANTY  
Covers units purchased as “new” in United States and  
Puerto Rico Only.  
Limitations and Exclusions  
VIZIO’s one-year limited warranty only covers defects  
in materials and workmanship. This warranty does  
not cover, for example: cosmetic damage, normal  
wear and tear, improper operation, improper voltage  
supply, signal issues, damage from shipping, acts  
of God, any type of customer misuse, modication  
or adjustments, as well as installation and set-up  
issues or any repairs attempted by anyone other than  
by a VIZIO authorized service center. Products with  
unreadable or removed serial numbers or requiring  
routine maintenance are not covered. This one year  
limited warranty does not cover Products sold “AS IS”,  
“FACTORY RECERTIFIED”, or by a non-authorized  
reseller. THERE ARE NO EXPRESS WARRANTIES  
OTHER THAN THOSE LISTED OR DESCRIBED  
ABOVE. ANY IMPLIED WARRANTIES, INCLUDING  
ANY IMPLIED WARRANTY OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE, SHALL  
BE LIMITED IN DURATION TO THE PERIOD OF TIME  
SET FORTH ABOVE. VIZIO’S TOTAL LIABILITY FOR  
ANY AND ALL LOSSES AND DAMAGES RESULTING  
FROM ANY CAUSE WHATSOEVER INCLUDING  
VIZIO’S NEGLIGENCE, ALLEGED DAMAGE, OR  
DEFECTIVE GOODS, WHETHER SUCH DEFECTS  
ARE DISCOVERABLE OR LATENT, SHALL IN NO  
EVENT EXCEED THE PURCHASE PRICE OF THE  
DEVICE. VIZIO SHALL NOT BE RESPONSIBLE  
FOR LOSS OF USE, LOSS OF INFORMATION  
OR DATA, COMMERCIAL LOSS, LOST REVENUE  
OR LOST PROFITS, OR OTHER INCIDENTAL OR  
CONSEQUENTIAL DAMAGES. SOME STATES DO  
NOT ALLOW LIMITATIONS ON HOW LONG AN  
IMPLIED WARRANTY LASTS OR THE EXCLUSION  
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
SO THE ABOVE LIMITATIONS OR EXCLUSIONS  
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES  
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY  
ALSO HAVE OTHER RIGHTS, WHICH VARY FROM  
STATE TO STATE. THIS WARRANTY IS SUBJECT TO  
FOR THE MOST CURRENT VERSION.  
VIZIO provides a warranty to the original purchaser  
of a new Product against defects in materials and  
workmanship for a period of one year of non-commercial  
usage and ninety (90) days of commercial use. If a  
Product covered by this warranty is determined to be  
defective within the warranty period, VIZIO will either  
repair or replace the unit at its sole option and discretion.  
To obtain warranty service, contact VIZIO Technical  
Support via email: Te[email protected] or via  
phone at 877 MY VIZIO (877.698.4946) from 6:00AM to  
9:00PM Monday through Friday and 8:00AM to 4:00PM  
Saturday and Sunday, Pacic Time, or visit www.VIZIO.  
com. PRE-AUTHOIRZATION MUST BE OBTAINED  
BEFORE SENDING A UNIT TO A VIZIO SERVICE  
CENTER. Proof of purchase in the form of a purchase  
receipt or copy thereof is required to show that the  
Product is within the warranty period.  
Parts and Labor  
There will be no charge for parts or labor during the  
warranty period. Replacement parts and units may be  
new or recertied at VIZIO’s option and sole discretion.  
Replacement parts and units are warranted for the  
remaining portion of the original warranty or for ninety  
(90) days from warranty service or replacement,  
whichever is greater.  
Type of Service  
Defective Products must be sent to a VIZIO service  
center to obtain warranty service. VIZIO is not  
responsible for transportation costs to the service center,  
but VIZIO will cover return shipping to the customer.  
PRE-AUTHORIZATION IS REQUIRED BEFORE  
SENDING ANY UNIT IN FOR WARRANTY SERVICE.  
All Product returns to VIZIO’s service center must utilize  
either the original blister pack and shipping material or  
packaging that affords an equal degree of protection.  
VIZIO Technical Support will provide instructions for  
packing and shipping the covered Product to the VIZIO  
service center.  
THE TRADEMARKS SHOWN HEREIN ARE THE  
PROPERTY OF THEIR RESPECTIVE OWNERS;  
IMAGES USED ARE FOR ILLUSTRATION PURPOSES  
ONLY. VIZIO, THE V LOGO AND WHERE VISION  
MEETS VALUE AND OTHER VIZIO TRADEMARKS  
ARE THE INTELLECTUAL PROPERTY OF VIZIO  
INC. PRODUCT SPECIFICATIONS ARE SUBJECT TO  
CHANGE WITHOUT NOTICE. © 2010 VIZIO INC. ALL  
RIGHTS RESERVED.  
14  
15  
XRU9M OM 2-6-10.indd 14-15  
2/6/2010 1:51:44 PM  
 
Use BLACK back cover  
supplied separately  
 
XRU9M OM 2-6-10.indd 16  
2/6/2010 1:51:44 PM  

Telular Fax Machine SX4e TDMA User Manual
Thermo Products Humidifier HA1042 User Manual
Timex Watch W 52 User Manual
Toshiba Computer Hardware T6963C User Manual
Tote Vision Computer Monitor EH 2001 User Manual
Troy Bilt Tiller 12209 User Manual
Troy Bilt Trimmer tb25ght User Manual
TVS electronic Printer RP 35 User Manual
Walker Snow Blower 5600 20 User Manual
Watlow Electric Electric Heater Responsive Heater User Manual