Vizio TV Mount WB 31 User Manual

INSTALLATION MANUAL  
FLAT LCD DISPLAY MOUNT MODEL  
WB-31 Swingout Arm Mount  
 
WB-31  
Warning Statements  
WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A  
MAXIMUM WEIGHT OF 50 LBS. IF NOT, THE WALL MUST BE REINFORCED.  
PROPER INSTALLATION PROCEDURE BYA QUALIFIED SERVICE TECHNICIAN, AS  
OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.  
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN  
DEATH.  
WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE  
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR  
THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.  
WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION  
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE  
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY  
AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN  
EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.  
Indicates that the power plug is to be disconnected from the power outlet.  
Safety precautions must be taken at all times.  
Warning and Caution statements.  
A secure structure must support the weight, or load, of the display. When mounting to a wall that contains  
wooden studs, dead center of the wooden stud must be confirmed prior to installation.  
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result  
in damage to the display and/or damage to the mounting surface.  
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure  
to do so may result in damage to the display and could increase the risk of fire.  
At least two qualified people should perform the installation procedure. Injury and/or damage can result from drop-  
ping or mishandling the display.  
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any sur-  
face other than wooden studs, use suitable hardware (which is commercially available).  
Contact Orion Images with any technical/ installation questions.  
Installation Instructions  
Page 3  
 
WB-31  
Parts List  
NOTE:  
This mount is shipped with all intallation hardware and components. Make sure that none  
of these parts are missing and/ or damaged before beginning installation. If there are parts  
missing and/or damaged, please stop and contact TOA Electronics, Inc.  
200x200 ADAPTER HARDWARE  
Swingout Arm (Qty 1)  
M6 x 30mm Phillips Pan  
Head Screws (Qty 4)  
M6 x 20mm Phillips Pan  
Head Screws (Qty 4)  
1/4” Wedge Anchors  
(Qty 4). These are used only  
for concrete installations.  
M6 x 12mm Phillips Pan Head  
Screws (Qty 4)  
M5 x 16mm Phillips Pan  
Head Screws (Qty 4)  
Mounting Backplate (Qty 1)  
M5 x 12mm Phillips Pan  
Head Screws (Qty 4)  
M4 x 20mm Phillips Pan  
Head Screws (Qty 4)  
M5 Flat  
Washer (Qty 4)  
M6 x 35mm Set Screw  
(Qty 1)  
M4 Flat  
Washer (Qty 4)  
M4 x 10mm Phillips Head  
Scews (Qty 4)  
M4 x 16mm SEMS  
Phillips Pan Head  
Screw (Qty 4)  
#14 x 2” Wood Screw  
(Qty 4)  
100x200 ADAPTER HARDWARE  
200x200 Adapter Plate  
(Qty 1)  
M4 x 5mm Phillips Pan Head  
Screws (Qty 4)  
M4 x 6mm Phillips Pan Head  
Screws (Qty 4)  
100x200 Adapter Plate  
(Qty 1)  
M4 x 10mm Phillips Flat  
Head Screws (Qty 6)  
Installation Tools  
Phillips Head Screw Driver Soft Material/ Blanket  
1/2" Socket and Wrench  
Level (Supplied)  
Pencil  
Tape Measure  
Drill Gun  
14mm Socket (Supplied)  
Ratchet with 9/16” Drive Socket  
M3 Allen Wrench (Supplied) Stud Finder (Commercially Available)  
Page 4  
Installation Instructions  
 
WB-31  
Backplate Installation - Wood Stud  
NOTE:  
These installation instructions will apply to the WB-31 Swingout Arm Mount.  
The following steps will outline how the back plate will be mounted.  
1. Determine where the mount location will be.  
2. Use a stud finder (sold separately) to locate the nearest wall stud.  
3. Once the wall stud has been located, dead-center of the wall stud must be determined.  
4. After this has been determined, line-up the holes of the backplate.  
NOTE: Be sure that the end of the back plate that has a “lip” is pointing down (Figure 1).  
5. Use the provided wood screws to attach the back plate to the wall (Figure 2).  
Figure 1. Backplate Mount  
Figure 2. Backplate Installation  
Installation Instructions  
Page 5  
 
WB-31  
Backplate Installation - Concrete Surface  
NOTE: These installation instructions will apply to the WB-31 Swingout Arm Mount.  
The following steps will outline how the back plate will be mounted.  
1. Determine where the mount location will be.  
2. After this has been determined, line-up the holes of the backplate.  
NOTE: Be sure that the end of the back plate that has a lip is pointing as shown in (Figure 3).  
3. Once the mounting holes are marked on the wall, use a 5/16” drill bit and drill 4 holes into the  
concrete surface (Figure 3).  
4. Once the holes have been drilled, gently tap the anchor studs into each hole, until the washer is flush  
(even) with the concrete surface.  
5. Place the backplate onto the concrete surface and slowly tighten each nut onto its respective anchor  
stud (Figure 4).  
Lip  
Lip  
Figure 3. Backplate - Concrete Surface  
Figure 4. Backplate Installation - Concrete  
Surface  
Page 6  
Installation Instructions  
 
WB-31  
WB-31 Installation  
1. The reverse side of the mount must be mounted to the back plate that is attached to the wall. The  
back of the mount contains an elongated rectangle (Figure 5). Referring to Figure 5, the back plate  
receptacle must be placed over the top of the back plate, so that the entire mount “hangs” on the  
back plate.  
2. Locate the access hole at the bottom of the mount base. Install the M6 x 35mm set screw with the  
M3 Allen wrench.  
3. Turn the Allen wrench clockwise (viewed from below) until the screw is secure.  
WARNING: Failure to fully tighten the locking screw may result in possible damage to your  
display.  
NOTE:  
In reference to Figure 5, the dash lines represent the back plate that is mounted to  
an existing surface.  
Figure 5. WB-31 Installation  
Installation Instructions  
Page 7  
 
WB-31  
(2) M4 x 10mm  
Phillips screws  
Display  
(2) M4 x 10  
Phillips screws  
Figure 6. Monitor Installation  
Installing the Monitor  
1. Loosely tighten two (2) M4 x 10mm Phillips Head screws to the top of the mounting points.  
2. Insert the head of the screws through the keyhole slots and then secure the bottom two (2)  
M4 x 10mm Phillips Head screws to secure the flat panel to the mounts, then tighten the upper  
M4 x 10mm Phillips Head screws (Figure 6).  
CAUTION:  
Do not over tighten the M4 x 10mm Phillips Head screws, or else damage to the  
display may occur.  
Cable Access  
Please refer to Figure 7 for the correct way to route existing any cables.  
WB-31 Articulating Swingout Arm - After the monitor has been mounted, remove the cable access plastic  
Articulating Swingout Arm  
Cable access  
holes  
Cable access  
plastic covers  
Figure 7. Cable Routing  
Page 8  
Installation Instructions  
 
WB-31  
Adjusting the Swingout Arm  
This unit comes pre-tensioned at the factory. To adjust the swingout Arm so that there will not be any move-  
ment, perform the following steps (Figure 8).  
1. Remove the Plastic End Caps.  
2. Take a 9/16” socket and ratchet and tighten the nut.  
3. Tighten, or loosen, each joint to the user’s satisfaction.  
4. Replace the Plastic End Caps.  
NOTE: The mount shown in this illustration is  
upside down to access the adjustment nuts.  
caps  
Bottom  
Top  
Adjustment  
nuts  
NOTE: The tilt/pivot adjustment nut is located  
on the back of the tilt/pivot mount.  
Figure 8. Swing Arm Adjustment  
Installation Instructions  
Page 9  
 
WB-31  
Adapter Plate Installation  
NOTE: If your flat panel is not a VESA 75/100, the 200x200 or the 100x200 Adapter Plates must be used.  
100x200 Aapter Plate  
1. Attach the 100x200 Adapter Plate to the back of the display using the provided hardware  
(see Parts List, page 4).  
2. Attach the WB-31 mounting plate to the back of the 100x200 using the M4 x 5 mm screws.  
200x200 Aapter Plate  
3. Figure 9B: Attach the 200x200 Adapter Plate to the back of the display using the provided  
hardware (see Parts List, page 4).  
4. Attach the WB-31 mounting plate to the back of the 200x200, or the 100x200 using the  
M4 x 5 mm screws.  
CAUTION: DO NOT OVERTIGHTEN THE SCREWS.  
Mounting Hardware (Please refer to Page 4  
for the correct mounting hardware that will  
be used with your display.  
100x200  
Mounting Hardware (Please refer to Page 4  
for the correct mounting hardware that will  
be used with your display.  
Display  
Figure 9A  
200x200  
Display  
Figure 9B  
Page 10  
Installation Instructions  
 
WB-31  
Technical Specifications  
Figure 11. WB-31 Swingout Arm  
Installation Instructions  
Page 11  
 
WB-31  
E255449 29GZ  
WALL MOUNT  
IN-WB31.R2  
Mfg. Date  
PN  
Page 12  
Installation Instructions  
 

Teac Computer Drive HD 15 C OTC User Manual
Teac Stereo System MC DX80I User Manual
Teac Stereo System W 860R User Manual
Toshiba Marine Radio PORTG R930 User Manual
Toshiba Projector TLP T70M User Manual
Trek Bicycle Accessories Bicycle Computer User Manual
Uniden Cordless Telephone 2465 User Manual
Uniden Cordless Telephone XC630 User Manual
Viking Outdoor Storage AD1620T User Manual
Vivitar Camcorder 980HD User Manual