Vizio Carpet Cleaner V 128 User Manual

Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 1  
Vax careline  
0870 6061248  
Carpet cleaner  
Vax model number:  
V-128  
Please read carefully before using this cleaner.  
Always fully extend the mains cable before use.  
Retain for future reference.  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 3  
Vax Careline 0870 606 1248  
20. Using improper voltage may result in damage to the  
motor and possible injury to the user. The correct  
voltage is listed on the rating label.  
2. Safety Information  
FOR HOUSEHOLD USE ONLY.  
21. A hazard may occur if the carpet washer runs over  
the power supply cord.  
When using the carpet washer, basic safety precautions  
should always be observed, including the following:  
22. To prevent dirty water from running into motor, do  
not hold the appliance upside-down or lay on its side.  
Use appliance in normal vacuuming position.  
1. Do not leave the carpet washer unattended when  
plugged in. Unplug it from socket when not in use.  
2. To prevent electric shock do not use outdoors.  
23. Use extra care when cleaning on stairs.  
3. Not to be used as a toy. Children should be supervised to  
ensure that they do not play with the appliance.  
24. Do not carry appliance while motor is running.  
4. This appliance is not intended for use by persons  
(including children) with reduced physical, sensory or  
mentalcapabilities, orlackofexperienceandknowledge,  
unless they have been given supervision or instruction  
concerning the use of the appliance by a person  
responsible for their safety.  
NOTE: Carpets should be dry vacuumed thoroughly  
before washing.  
NOTE: The unit must be unplugged from the mains  
socket outlet after use, and before cleaning or  
maintaining the unit.  
NOTE: The brush bar will only rotate when the  
machine is in the reclined floor cleaning position and  
the power switch is on. The brushbar will turn off  
when in tool mode or upright position.  
5. Use only as described in this manual.  
6. Do not use with a damaged cord or plug. If the supply  
cord and/or plug is damaged, they must be replaced  
by the manufacturer, a Vax Service Agent or similarly  
qualified persons in order to avoid hazard.  
IMPORTANT: This unit is not intended for  
commercial use.  
!
7. Do not pull or carry by the cord, use the cord as a  
handle, allow the cord to come into contact with hot  
or sharp surfaces or close a door on the cord.  
PLEASE KEEP THESE INSTRUCTIONS  
FOR FURTHER USE.  
8. Do not unplug by pulling on the cord.  
9. Do not handle the plug or carpet washer with wet  
hands.  
10. Do not put any objects into openings or operate with  
openings blocked, keep them free of anything that  
may reduce airflow.  
11. Keep hair, loose clothing, fingers and all parts of the  
body away from openings and moving parts.  
12. Do not use the carpet washer on any glowing,  
burning or smoking particles.  
13. Do not use without the solution tank and dirty water  
tank in place.  
14. Turn off all controls before unplugging.  
15. Do not use to pick up flammable or combustible  
liquids such as petrol, or use in areas where they may  
be present.  
16. Keep the unit on the floor.  
17. Do not use an extension cord.  
18. Do not attempt to remove blockages with sharp  
objects as they may cause damage.  
19. Store indoors put away after use to prevent tripping  
accidents.  
3
safety information  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 4  
3. Carpet Cleaner Basics  
Unfold handle  
Raise handle from storage position until it locks in place  
(Fig.3/1).  
A
Fig.3/4  
Turn tank upside down and unscrew cap (B) (Fig.3/5). The  
cap consists of 2 pieces - the cap ring (C) and the solution  
tank valve (D).  
B
Fig.3/1  
Slide collar (A) up on telescoping handle (B) to adjust  
handle to desired height (Fig.3/2).  
C
A
B
D
Fig.3/5  
Pour solution into tank to solution fill line (E) (Fig.3/6).  
Fig.3/2  
Folding handle  
Push up on the collar (A) to lower the telescoping handle.  
Rotate knob (C) backwards to drop the handle into storage  
position (Fig.3/3).  
A
E
Fig.3/6  
Fill tank completely with hot tap water (max 50°C).  
Replace cap. Be sure the valve (D) is in the cap ring (C)  
before screwing the cap back on the tank (Fig.3/5).  
C
Place tank back onto cleaner (Fig.3/7), pressing firmly to  
be sure tank is fully positioned.  
CAUTION: Avoid solution contact with the eyes and  
skin. In case of contact with eyes, flush with cold  
water for 15 minutes. In case of contact with skin, wash  
with water. If irritation persists, consult your GP.  
Fig.3/3  
!
Filling the Solution Tank  
IMPORTANT: Unplug carpet cleaner from electrical outlet.  
Pull up on solution tank handle (A) and remove solution  
tank (Fig.3/4).  
4
unfolding handle / filling the solution tank  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 5  
Vax Careline 0870 606 1248  
Lift up on tank (D) and pull off (Fig.3/10).  
D
Fig.3/7  
Fig.3/10  
Emptying the Recovery Tank  
Lift up on tank lid latches (E) and remove the tank lid (F),  
including the float (G) (Fig.3/11). Empty tank.  
IMPORTANT: Unplug carpet cleaner from electrical outlet.  
An automatic shut-off device prevents the carpet cleaner  
from picking up more dirty water than it can hold in the  
recovery tank.  
F
E
You will know the tank needs to be emptied -  
• When the motor sound rises in pitch.  
E
You do not see dirty solution coming up through the  
recovery tank lid.  
G
• The float (A) inside the recovery tank has risen to the top  
of the tank (Fig. 3/8), and is visible through the lid  
window (B).  
Fig.3/11  
B
Replace lid. Secure both latches (E) (Fig.3/11).  
NOTE: For full suction, it is important that the recovery  
tank lid is properly secured before replacing or operating.  
Remove any debris that has collected on lint filter (H) on  
cleaner body (Fig.3/12 and inset).  
A
H
Fig.3/8  
Step on handle release pedal (C) to lower handle and  
unlock the recovery tank (Fig.3/9).  
Fig.3/12  
Place tank onto cleaner. Return handle to upright position.  
Transporting  
Your carpet cleaner may be transported easily by the  
convenient carrying handle (see item 4, page 2).  
C
Fig.3/9  
5
emptying the recovery tank / transporting  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 6  
Storing Hose and Tool  
4. Hose and Tools  
To return hose wand to storage position, align bump (E) on  
Using the Hose  
wand with hole (G) in nozzle and push in firmly until you  
hear a snap (Fig.4/4).  
Place handle in upright, storage position.  
Press on the tab (A) to remove the hose wand (B) from the  
floor nozzle (C) (Fig.4/1).  
E
B
G
A
Fig.4/4  
C
NOTE: Hose wand must be returned to floor nozzle  
storage position in order for cleaner to be used in the  
upright position for floor cleaning.  
Fig.4/1  
Attaching Tool  
Store upholstery nozzle (H) over projection (I) on back of  
cleaner for storage (Fig.4/5).  
Stair/upholstery nozzle has a built-in brush to help  
provide the scrubbing action some spots may need for  
removal (Fig.4/2).  
H
I
Fig.4/5  
Fig.4/2  
Slide tool (D) onto end of hose wand. Snap tool over bump  
(E) on wand (Fig.4/3).  
D
F
E
Fig.4/3  
Removing Tool  
To remove tool: Push forward and up on tab (F). Slide tool  
off hose wand.  
6
hose and tools  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 7  
Vax Careline 0870 606 1248  
NOTE: Use only Vax brand solutions in your carpet cleaner.  
Other brands may damage the carpet cleaner.  
5. Cleaning Carpet  
Remove lightweight furniture (tables, lamps, etc.) from  
area to be cleaned.  
To reduce the risk of fire, do not use a flammable or  
combustible liquid to clean floor.  
Protect any remaining furniture by pinning up furniture  
skirts and placing aluminum foil or plastic under legs.  
Plan your cleaning to avoid walking on wet carpet. Start at  
the end of the room farthest from the exit and work in  
small sections (Fig.5/4).  
Vacuum carpet thoroughly to remove loose dirt, hair, lint  
and other debris (Fig.5/1).  
Start  
Exit  
Fig.5/4  
Fig.5/1  
Raise handle from storage position until it locks in place.  
Slide collar (A) on telescoping handle (B) to adjust handle  
to desired height. (Fig.5/5). Step on handle release pedal  
and lower handle. Turn cleaner ON.  
Test solution for colorfastness on a hidden area of carpet.  
Wet a white cloth or paper towel with some solution.  
Gently rub onto a hidden area of carpet. Wait ten minutes.  
Blot with white cloth or paper towel and check for  
color transfer.  
B
Pretreat spots, stains and high traffic areas with Vax  
Pre-Treatment Spray (Fig.5/2).  
A
Fig.5/5  
Squeeze and hold trigger to release cleaning solution  
(Fig.5/6). Push cleaner forward SLOWLY then pull it back  
SLOWLY.  
Fig.5/2  
Fill solution tank with hot tap water (max water  
temperature 50°C) and proper amount of Vax cleaning  
solution (see page 4) (Fig.5/3).  
Fig.5/6  
Let go of trigger and push carpet cleaner over same area  
to pick up dirty solution without putting down more  
solution.  
Fig.5/3  
7
cleaning carpet  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 8  
Continue using dry strokes until you see only a little  
solution coming up through the nozzle (front of extractor)  
or recovery tank lid.  
Do not make the carpet too wet! Use no more than two  
sets of forward and backward strokes while releasing  
solution. Always follow with dry strokes - the more the  
better.  
Listen carefully! When the motor sound changes (rises in  
pitch), the recovery tank needs to be emptied. When water  
has reached the maximum capacity in the recovery tank,  
the float will rise to the top of the tank and the cleaner will  
NOT pick up dirty solution.  
Fig.6/2  
NOTE: Use only Vax brand solutions in your carpet cleaner.  
Other brands may damage the carpet cleaner.  
Allow carpet to dry. Avoid walking on the carpet until it is  
dry. Increased air circulation (open doors, turn on fans, etc.)  
will help carpet dry thoroughly.  
Place handle in upright, storage position. Press on the tab  
(A) to remove the hose wand (B) from the floor nozzle (C)  
(Fig.6/3).  
Vacuum thoroughly after carpet has dried. This will reduce  
any shading left by the carpet cleaner’s brushes.  
NOTE: No cleaning solution removes all stains from all  
carpets. Stain removal varies with the type of spill, time  
passed before removal, carpet material, and carpet type.  
B
6. Cleaning Upholstery  
IMPORTANT: Check fabric manufacturer’s  
instructions to confirm that it is alright to use your  
carpet cleaner to clean the upholstery.  
A
!
C
Vacuum upholstery thoroughly with your vacuum  
cleaner’s attachments.  
Fig.6/3  
Slide tool (D) onto end of hose wand. Snap tool over  
bump (E) on wand (Fig.6/4).  
Test solution for colorfastness on a hidden area of  
upholstery. Wet a white cloth or paper towel with some  
solution. Gently rub onto a hidden area of upholstery.  
Wait ten minutes. Blot with white cloth or paper towel  
and check for color transfer.  
D
F
Pretreat spots and stains with Vax Pre-Treatment Spray  
(Fig.6/1).  
E
Fig.6/4  
Squeeze and hold trigger (A) to release cleaning solution.  
Gently press tool into fabric and slowly pull the tool over  
the fabric (Fig.6/5).  
Fig.6/1  
Fill solution tank with hot tap water (max water  
temperature 50°C) and proper amount of Vax cleaning  
solution (see page 4) (Fig.6/2).  
8
cleaning upholstery  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 9  
Vax Careline 0870 606 1248  
7. Maintenance  
Cleaning the Nozzle  
Unplug carpet cleaner from electrical outlet.  
Wipe debris off nozzle and front of cleaner with a damp  
cloth (Fig.7/1).  
A
Fig.6/5  
Let go of trigger and pull tool over same area to pick up  
dirty solution without putting down more solution.  
Continue using dry strokes until you see only a little  
solution coming up through the tool.  
A
Do not make the upholstery too wet! Use no more than  
two strokes while releasing solution. Always follow with  
dry strokes - the more the better.  
Fig.7/1  
Cleaning the Brushes  
Listen carefully! When the motor sound changes (rises in  
pitch), the recovery tank need to be emptied. When water  
has reached the full line in the recovery tank, the cleaner  
will NOT pick up dirty solution.  
Unplug carpet cleaner from electrical outlet.  
Remove solution and recovery tanks to prevent possible  
leaks.  
Tilt cleaner back so handle rests on the floor (Fig.7/2).  
Allow upholstery to dry. Avoid using upholstery until it is  
dry. Increased air circulation (open doors, turn on fans,  
etc.) will help upholstery dry thoroughly to prevent the  
growth of mold or mildew.  
Fig.7/2  
Remove any carpet fibers or strings that may be attached  
to the brushes (Fig.7/3).  
Fig.7/3  
Empty solution tank and rinse thoroughly.  
9
maintenance  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 10  
Place empty solution tank on carpet cleaner. Turn carpet  
9. Troubleshooting  
cleaner ON. Squeeze trigger and push carpet cleaner  
forward and back several times, using the cleaner to pick  
up the remaining liquid. This will clear any solution  
remaining inside the cleaner.  
WARNING: To reduce the risk of personal injury,  
!
unplug the vacuum cleaner before performing  
maintenance or troubleshooting checks.  
PROBLEM: The cleaner won't run.  
8. Storage  
Cause:  
Not properly plugged into electrical outlet.  
Empty recovery tank, rinse thoroughly and let air dry.  
Solution: Plug in firmly.  
Allow brushes and underside of carpet cleaner to air dry  
thoroughly before storing carpet cleaner on a carpeted or  
wood surface.  
Cause:  
No electricity in electrical outlet.  
Solution: Check fuse or breaker.  
Cause:  
Solution: Push on/off switch to ‘on’.  
Cause: Blown fuse/tripped breaker.  
ON/off switch not turned on.  
Push up on the collar (A) and lower the telescoping handle.  
Rotate knob (B) backwards to drop the upper handle into  
storage position (Fig.8/1).  
Solution: Reset circuit breaker or replace fuse.  
A
PROBLEM: Cleaner won’t pick up/loss of suction.  
Cause:  
Dirty water tank is full.  
B
Solution: Switch off and unplug cleaner. Empty dirty  
water tank as shown in Section 3.  
Cause:  
Recovery tank and lid not correctly installed.  
Solution: Replace tank and lid securely.  
Cause:  
Hose/wand tool not securely in position.  
Solution: Securely position hose/tool in floor nozzle.  
Fig.8/1  
Cause:  
Lint filter blocked.  
Solution: Check lint filter and remove any debris.  
To store the cleaner, ensure all tanks are clean, empty  
and dry.  
PROBLEM: Brushes won’t rotate.  
Cause:  
Handle is not in the operating position.  
Solution: Brushes only rotate when the handle is in the  
reclined, floor cleaning position.  
Cause:  
Circuit breaker tripped.  
Solution: Turn cleaner off and unplug. Check for  
obstructions in the brush bar. Allow the  
cleaner to cool, then switch on and continue  
cleaning.  
PROBLEM: Low suction in hose.  
Cause:  
Solution: Securely attach tool to tool connector.  
Cause: Handle is not in upright, storage position.  
Solution: Make sure handle is in upright position.  
Tool not properly connected.  
Cause:  
Recovery tank is full - automatic shut-off  
engaged.  
Solution: Make sure handle is in upright position.  
Cause:  
Handle is not in upright, storage position.  
Solution: Switch off and unplug cleaner. Empty dirty  
water tank as shown in Section 3.  
Cause:  
Lint filter blocked.  
Solution: Check lint filter and remove any debris.  
10  
storage / troubleshooting  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 11  
Vax Careline 0870 606 1248  
10. UK Service & Help  
11. Technical Specification  
Voltage:  
Wattage:  
Capacity:  
220-240V ~50Hz  
700 W  
Clean water tank - 1.8 litres  
Dirty water tank - 1.3 litres  
6 metres  
Vax Care 0870 6061248  
Monday-Friday  
8.00am to 6.00pm  
Saturday-Sunday 9.00am to 5.00pm  
An answerphone is available outside of these hours. Any  
queries or concerns about using the Vax, call the Vax  
Careline. Calls are charged at the UK national rate.  
Cord length:  
Weight:  
8 kg  
Subject to technical change without notice.  
Please make a note of the serial number and model  
number of the carpet cleaner before calling. There are over  
400 approved Vax Service Agents in the UK. For the  
nearest Service Agent, please call the Vax Careline.  
11  
uk service & help / technical specification  
 
Vax V-128 User Guide.qxd:V-128 User Guide 14/4/08 16:01 Page 12  
---  
EEC STATEMENT OF COMPLIANCE  
Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility, declare that the  
V-128 Agility Compact carpet cleaner is manufactured in compliance with the following Directives:  
Safety: 2006/95/EC Low Voltage Directive  
EMC: 2004/108/EC Electromagnetic Compatibility Directive  
Waste electrical products should not be disposed of with household waste. Please recycle where  
facilities exist. Check with your Local Authority or retailer for recycling advice.  
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 OQH, UK  
 

Technicolor Thomson DVD Player DTH8000 User Manual
Technics Stereo System SC S305 User Manual
Technika CD Player BB 129I User Manual
Toshiba Computer Monitor 27WL46 User Manual
Toshiba Flat Panel Television C3000 Series X3000 Series User Manual
Tripp Lite TV Cables A102 04M User Manual
Viking Range professional custom series free standing gas 60w sealed burner range User Manual
Volvo Automobile 940 User Manual
Wayne Plumbing Product CDUCAP Series User Manual
Weed Eater Lawn Mower WE1538A User Manual