A s s e m b l y
G u i d e
E3600iNetTV
COMMERCIAL FITNESS BIKE
TOOLS & PARTS INCLUDED
MM
Screwdriver
15 Pedal Wrench
MM
5 Allen Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty: 1
Color-coded Hardware Bags
Assembly Guide
CONSOLE BOX
iNetTV Console
Owner’s Guide
Warranty Card
HARDWARE INCLUDED
ORANGE BAG
PINK BAG
M8 x 65L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 2
BLUE BAG
M8 Lock Washer
Quantity: 6
M8 x 15L Screw
Quantity: 7
STEP
1
ORANGE BAG
• Install the rear foot with the four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
STEP
1
MM
(M8x20L). Tighten with the 5 Allen
wrench.
5
STEP
2
BLUE BAG
STEP
2
• Slide the rubber boot onto the
console mast.
• Locate the bundle of wires that
comes from the bracket on top of the
bike frame. Wrap these wires with the
wire tie coming from the bottom of the
console mast. Pull the wire tie and
bundle of wires up through the top of
the console mast while simultaneously
sliding the mast into the frame
bracket.
• Secure the console mast to the
frame bracket with six lock washers
(M8) and six screws (M8x15L).
MM
Tighten with the 5 Allen wrench.
Place the seventh screw (M8x15L) in
the rear of the frame bracket and
tighten until snug.
• Slide the console mast boot down
and snap it into place on the side
cover.
• Remove the nuts (M8) from the
screws on the bottom of the seat.
Attach the seat to the seat post with
the nuts you just removed. Tighten with
MM
the 15 wrench.
• Loosen the seat post knob and slide
the seat post into place in the seat
tube bracket.
6
STEP
3
PINK BAG
• Feed the heart rate wires from the
handlebars through the small hole
located in the front of the console
mast. Pull these wires up through the
hole at the top of the console mast.
Attach the handlebar to the console
mast using two lock washers (M8)
and two screws (M8x20L). Tighten
STEP
3
MM
with the 5 Allen wrench.
7
STEP
4
CONSOLE
• Remove the six mounting screws
from the back of the console with the
Phillips screwdriver. Set the console in
place and secure it to the console
mast with the screws you just
removed. Connect all the wires to the
proper locations in the back of the
console (see diagram).
STEP
4
• With the Phillips screwdriver remove
the two screws located half way up
the console mast. Attach the water
bottle bracket to the console mast with
the two screws. Insert the water bottle.
1 - Co-Axial Cable TV
2 - USB - B
3 - USB - A
1
2
3
4
5
6
7
8
4 - VGA (PC Video)
5 - Video IN
6 - Audio - R
7 - Audio - L
9
WIRES
8 - Microphone
9 - Heart Rate Reciever 1
10 - Heart Rate Reciever 2
11 - 20 Pin Connector
12 - Power Plug
10
12
13
11
13 - Miles/Kilometers Switch
14 - Data Port
14
500 South CP Avenue
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z36CB40-AG1824PRD
AG18.24PRD
REV1
8
|