Viper Automobile Alarm 160XVL User Manual

Model 160XVL  
Owner's Guide  
 
HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING  
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS  
WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REIN-  
STALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE  
EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED ELECTRONICS OR ITS SUB-  
SIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF  
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL  
APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM  
AGAINST DIRECTED ELECTRONICS SHALL BE STRICTLY LIMITED TO THE AUTHORIZED  
DIRECTED ELECTRONICS DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED ELEC-  
TRONICS SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER,  
INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL  
DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL  
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE  
ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR  
REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow lim-  
itations on how long an implied warranty will last or the exclusion or limitation of  
incidental or consequential damages. This warranty gives you specific legal rights and  
you may also have other rights that vary from State to State.  
This product may be covered by a Guaranteed Protection Plan ("GPP"). See your  
authorized Directed Electronics dealer for details of the plan or call Directed  
Electronics Customer Service at 1-800-876-0800. Directed Electronics security systems,  
including this unit, are deterrents against possible theft. Directed Electronics is not  
offering a guarantee or insurance against vandalism, damage or theft of the automo-  
bile, its parts or contents; and hereby expressly disclaims any liability whatsoever,  
including without limitation, liability for theft, damage and/or vandalism. Directed  
Electronics does not and has not authorized any person or entity to create for it any  
other obligation, promise, duty or obligation in connection with this security system.  
Make sure you have all of the following information from your dealer:  
A clear copy of the sales receipt, showing the following:  
Date of purchase  
Your full name and address  
Authorized dealer's company name and address  
Type of alarm installed  
Year, make, model and color of the automobile  
Automobile license number  
Vehicle identification number  
All security options installed on automobile  
Installation receipts  
ii  
2006 Directed Electronics—all rights reserved  
©
 
Table of Contents  
Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . i  
Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
What is Included  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Important Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Your Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
FCC/ID Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Transmitter Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Standard Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Using Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Warning! Safety First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Disarming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Disabling the Starter Kill Without a Transmitter. . . . . . . . . . . . . . . . . . . . . . . 11  
Valet Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Panic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Rear Defogger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Valet Take-Over. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Short-Run/Turbo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Starter Anti-Grind Circuitry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Disabling the Remote Start System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Rapid Resume Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Programming Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
nComfort closure is a programming option which closes the vehicle’s windows  
after remote locking.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Convenience Expansions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Quick Reference Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
1
2006 Directed Electronics—all rights reserved  
©
 
Standard Configuration  
controls the Arm/Panic ON/Panic OFF function.  
controls the Disarm function.  
controls Silent Mode™and an Auxiliary Output.  
controls Remote Start.  
+
controls Timer mode.  
+
+
controls Turbo/Short Run.  
controls Channel 4 output.  
+ +  
controls Rear Defroster.  
2
2006 Directed Electronics—all rights reserved  
©
 
What is Included  
The control module  
A Venom SST receiver/antenna  
Two four-button transmitters  
The blue status LED indicator light  
A push-button Valet button  
Your warranty registration  
A shut-down toggle switch  
Important Information  
Congratulations on the purchase of your remote start keyless entry  
system. Due to the complexity of this system, it must be installed  
by an authorized dealer only. Installation of this product by any-  
one other than an authorized dealer voids the warranty. All deal-  
ers are provided with a preprinted dealer certificate to verify that  
they are authorized.  
By carefully reading this Owner's Guide prior to using your system,  
you will maximize the use of this system and its features.  
You can print additional or replacement copies of this manual by  
accessing the Directed Electronics internet website at  
3
2006 Directed Electronics—all rights reserved  
©
 
System Maintenance  
The system requires no specific maintenance. Your remote is powered  
by two small, lightweight 3-volt lithium batteries that will last  
approximately one year under normal use. When the battery begins to  
weaken, operating range will be reduced and the LED on the remote  
will dim.  
Your Warranty  
Your warranty registration must be completely filled out and  
returned within 10 days of purchase. Your product warranty  
will not be validated if your warranty registration is not returned.  
Make sure you receive the warranty registration from your dealer.  
It is also necessary to keep your proof of purchase, which reflects  
that the product was installed by an authorized dealer.  
FCC/ID Notice  
This device complies with Part 15 of FCC rules. Operation is subject  
to the following conditions: (1) This device may not cause harmful  
interference, and (2) This device must accept any interference re-  
ceived, including interference that may cause undesired operation.  
Changes or modifications not expressly approved by the party responsible  
for compliance could void the user's authority to operate this device.  
HHU, hand held unit  
To satisfy FCC RF exposure compliance requirements, this device should  
be used in hand-held, hand operated configurations only. The device  
4
2006 Directed Electronics—all rights reserved  
©
 
and its antenna must maintain a separation distance of 20 cm or more  
from the person’s body, except for the hand and wrists, to satisfy RF  
exposure compliance. This device is designed to be used in a person’s  
hands and its operating configurations do not support normal trans-  
missions while it is carried in pockets or holsters next to a persons’  
body.  
Caution  
This product is designed for fuel injected, automatic transmission  
vehicles only. Use of this product in a standard transmission vehi-  
cle is dangerous and contrary to the product's intended use.  
5
2006 Directed Electronics—all rights reserved  
©
 
Transmitter Functions  
The receiver uses a computer-based learn routine to learn the  
transmitter buttons. This makes it possible to assign any specific  
transmitter button, or combination of buttons, to any receiver  
function. The transmitter initially comes programmed with the  
Standard Configuration, but may also be customized by an autho-  
rized dealer. The transmitter buttons indicated in all of the instruc-  
tions in this manual correspond to a Standard Configuration trans-  
mitter.  
Standard Configuration  
Button  
The arming and panic functions are controlled by pressing  
the transmitter for one second.  
on  
Button  
The disarm function is controlled by pressing  
ter for one second.  
on the transmit-  
Button  
Silent Modeand an optional auxiliary function are controlled  
by pressing . Silent Mode works by pressing for less than  
one second. An optional auxiliary function, such as  
trunk release, is controlled by pressing and holding  
1.5 seconds.  
for  
Button  
6
2006 Directed Electronics—all rights reserved  
©
 
The remote start function of your system is controlled by pressing  
this button twice within 3 seconds.  
and  
Buttons  
An optional auxiliary convenience or expansion function that you  
have added to your system can be activated by pressing these but-  
tons simultaneously.  
The auxiliary output controls __________________________.  
Buttons  
+
+
When simultaneously pressed these buttons control the rear win-  
dow defogger during remote starting.  
Using Your System  
Warning! Safety First  
The following safety warnings must be observed at all times:  
Due to the complexity of this system, installation of this  
product must only be performed by an authorized Directed  
Electronics dealer.  
When properly installed, this system can start the vehicle via  
a command signal from the remote control transmitter.  
Therefore, never operate the system in an enclosed area or  
partially enclosed area without ventilation (such as a garage).  
7
2006 Directed Electronics—all rights reserved  
©
 
When parking in an enclosed or partially enclosed area or  
when having the vehicle serviced, the remote start system  
must be disabled using the installed toggle switch. It is the  
user's sole responsibility to properly handle and keep out of  
reach from children all remote control transmitters to assure that  
the system does not unintentionally remote start the vehicle.  
THE USER MUST INSTALL A CARBON MONOXIDE DETECTOR  
IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.  
ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE  
ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE  
AREA MUST AT ALL TIMES REMAIN CLOSED. These precau-  
tions are the sole responsibility of the user.  
Use of this product in a manner contrary to its intended mode  
of operation may result in property damage, personal injury,  
or death. (1) Never remotely start the vehicle with the vehi-  
cle in gear, and (2) Never remotely start the vehicle with the  
keys in the ignition. The user must also have the neutral safe-  
ty feature of the vehicle periodically checked, wherein the  
vehicle must not remotely start while the car is in gear. This  
testing should be performed by an authorized Directed  
Electronics dealer in accordance with the Safety Check out-  
lined in the product installation guide. If the vehicle starts in  
gear, cease remote start operation immediately and consult  
with the authorized Directed Electronics dealer to fix the  
problem.  
After the remote start module has been installed, contact your  
authorized dealer to have him or her test the remote start  
8
2006 Directed Electronics—all rights reserved  
©
 
module by performing the Safety Check outlined in the prod-  
uct installation guide. If the vehicle starts when performing  
the Neutral Safety Shutdown Circuit test, the remote start unit  
has not been properly installed. The remote start module must  
be removed or the installer must properly reinstall the remote  
start system so that the vehicle does not start in gear. All  
installations must be performed by an authorized Directed  
Electronics dealer. OPERATION OF THE REMOTE START MOD-  
ULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS  
INTENDED MODE OF OPERATION. OPERATING THE REMOTE  
START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN  
PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMME-  
DIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSIS-  
TANCE OF AN AUTHORIZED DIRECTED ELECTRONICS DEALER  
TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START  
MODULE. DIRECTED ELECTRONICS WILL NOT BE HELD  
RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLA-  
TION COSTS.  
Arming  
Pressing  
for one second arms the system by activating the  
starter kill and locking the doors (if the door locks are connected).  
The horn will honk (if connected) and the parking lights will flash  
once to confirm arming of the system. While the system is armed,  
the status LED will flash once per second. The Failsafe® Starter Kill  
(if installed) will also prevent the vehicle’s starter from cranking.  
The system can also be programmed to arm the optional Failsafe®  
9
2006 Directed Electronics—all rights reserved  
©
 
Starter Kill automatically (called Passive Mode). If the system has  
been programmed for Passive Mode, the Failsafe® Starter Kill will  
automatically activate 30 seconds after the ignition has been  
turned off. After the ignition has been turned off, the status LED  
will flash rapidly to indicate that the system is in Passive Mode.  
If Passive Mode has been programmed on, then it is also possible  
to program the system for Passive Locking. With Passive Locking,  
the vehicle doors lock automatically at the same time that the  
Failsafe® Starter Kill is activated. If Passive Locking is programmed  
on, care must be taken to prevent the keys from being locked in the  
vehicle.  
NOTE: For Passive Mode to be effective, the Failsafe® Starter Kill relay  
must be installed.  
Disarming  
Pressing  
for one second disarms the system and unlocks the  
doors (if connected). The horn will honk twice (if connected) and  
the parking lights will flash twice to confirm disarming of the sys-  
tem. The optional Failsafe® Starter Kill will be deactivated. The sta-  
tus LED will turn off, unless the system is programmed for Passive  
Mode. In Passive Mode, the status LED will flash rapidly when the  
system is disarmed. This indicates that the system will re-engage  
the starter kill and re-lock the doors (if Passive Locking has been  
programmed) in 30 seconds unless the ignition is turned on.  
10  
2006 Directed Electronics—all rights reserved  
©
 
Disabling the Starter Kill Without a Transmitter  
If your remote transmitter is lost or damaged, you can manually  
override the starter kill. To do this, you must have the vehicle's  
ignition key and know where the Valet button is located. Be sure  
to check with the installer for the location of the Valet button.  
To override the starter kill, turn  
the ignition on and press the  
Valet button within 10 seconds.  
DRW-35  
The status LED will stop flashing  
and the vehicle should start. If it does not start,  
you may have waited too long; turn the ignition off and repeat the  
process.  
LOCATION OF VALET BUTTON_____________________________  
Valet Mode  
You can prevent your system from automatically activating the  
Failsafe® Starter Kill and locking the doors by using Valet Mode.  
This is very useful when washing the vehicle or having it serviced.  
In Valet Mode, the starter kill cannot be activated, even with the  
transmitter, but all convenience functions (door locks, remote  
start, etc.) will continue to work normally.  
11  
2006 Directed Electronics—all rights reserved  
©
 
To enter or exit Valet Mode:  
1. Turn the ignition on.  
2. Turn the ignition off.  
3. Press and release the Valet  
button within 10 seconds.  
DRW-35  
The status LED will light steadily if you are entering Valet Mode  
and will turn off if you are exiting Valet Mode.  
Panic Mode  
If you are threatened in or near your vehicle, you can attract  
attention by triggering the system with your transmitter. Just  
press  
for 1.5 seconds to enter Panic Mode. In Panic Mode, the  
horn will honk and the parking lights will flash for 30 seconds. To  
stop Panic Mode at any time, press  
transmitter.  
, or  
on the  
NOTE: In order for Panic Mode to be effective, the vehicle’s horn (or  
optional siren) as well as the vehicle's parking lights must be  
connected.  
12  
2006 Directed Electronics—all rights reserved  
©
 
Remote Start  
This feature allows you to remotely start and run your vehicle for  
a programmable period of time. This makes it possible to warm up  
the engine, as well as adjust the interior temperature of the vehi-  
cle with the climate control system. If interior heating or cooling  
is desired, the climate controls must be preset, and the fan blower  
must be set to the desired level prior to remote starting the  
vehicle.  
IMPORTANT! (1) Never remotely start the vehicle with the vehicle  
in gear, and (2) Never remotely start the vehicle with the key in the  
ignition.  
To remote start the vehicle:  
1. Press the  
mitter.  
button twice within 3 seconds on the trans-  
2. The parking lights will flash to confirm that the vehicle will  
attempt to start.  
3. Release the  
button as soon as the parking lights flash.  
(In gasoline vehicles, the engine will start 4 seconds after  
the parking lights flash. In diesel vehicles, the engine will  
start when the WAIT-TO-START indicator on the vehicle's dash  
goes out or the timer has expired.)  
4. Once the vehicle has started, it will run for the pre-program-  
med period of time (12, 24, or 60 minutes) or until a shut-  
down input is triggered.  
13  
2006 Directed Electronics—all rights reserved  
©
 
When you are ready to drive the vehicle:  
1. Insert the ignition key and  
turn it to the ON (not the  
START) position.  
2.  
Press the brake pedal.  
NOTE: If the brake pedal is pressed before the key is in the ON position,  
the engine will shut down.  
While the vehicle is running during remote start operation, the  
system will monitor the vehicle and will automatically shut down the  
engine if the system receives any of the following shut-down inputs:  
The brake pedal is pressed.  
The hood is opened.  
The shutdown toggle switch is put into the OFF position.  
The pre-programmed run time (12, 24, or 60 minutes) has elapsed.  
Transmitter button  
is pressed twice in 3 seconds to start  
the vehicle.  
Rear Defogger  
To turn the rear defogger output OFF:  
1. Simultaneously press & release the  
on the remote control.  
+
+
buttons  
2. The lights will flash 2 times.  
3. The rear defogger output will no longer activate when the  
vehicle is remote started.  
NOTE: If the remote start is on the parking lights will turn off then flash  
2-times before returning to their normal output and the defogger out-  
put, if active, will cease.  
14  
2006 Directed Electronics—all rights reserved  
©
 
To turn the rear defogger output ON:  
1. Simultaneously press & release the  
on the remote control.  
+
+
buttons  
2. The lights will flash 3 times.  
3. The rear defogger output will once again activate when the  
vehicle is remote started.  
NOTE: If the remote start is on the lights will turn off then flash 3-times  
before returning to their normal output and the defogger output will  
activate as programmed.  
Valet Take-Over  
The Valet Take-Over feature allows the vehicle to remain running  
after the key has been removed from the ignition. This feature is  
useful for occasions when you wish to exit and lock the vehicle for  
short periods of time, but would like to leave the motor running  
and the climate controls on.  
To perform Valet Take-Over:  
1. Before turning off the engine, press and release  
on the  
transmitter twice in 3 seconds (or press and release the  
optional momentary switch).  
2. Turn the ignition key to the OFF position. (The engine will  
stay running.)  
3. Once the vehicle has started, it will run for the pre-pro-  
grammed period of time (12, 24, or 60 minutes) or until a  
shutdown input is triggered.  
2005 Directed Electronics—all rights reserved  
15  
©
 
Short-Run/Turbo  
Short-run turbo mode keeps the engine running after arriving at  
you destination for a programmable period of 1, 3 ,5 or 10 min-  
utes. This allows the system’s timer to conveniently cool down the  
turbo after you have left the vehicle.  
To activate:  
1. Park the vehicle and set parking brake.  
2. Remove your foot from the brake pedal and leave the engine  
running.  
3. Press and release the  
and  
buttons at the same time.  
4. The lights will flash to indicate the remote start has entered  
short run turbo mode.  
5. Turn off the key, the engine will keep running.  
6. Exit and secure the vehicle.  
7. The engine will turn off after the programmed run time.  
Timer Mode  
By pressing the remote  
and  
buttons the parking  
lights will flash 4 times and then start the vehicle and run for the  
set duration. The remote start can be shut off by the transmitter  
by pressing the remote start button  
and remain in timer  
mode, but if any other shut down zones or the ignition becomes  
active the timer mode will cancel.  
1. Press Timer mode buttons.  
16  
2006 Directed Electronics—all rights reserved  
©
 
2. The vehicle will confirm with 4 parking light flashes.  
3. A 1-second delay will start.  
4. The system will start the car and will run for the specified  
duration, unless shut down by the remote start button  
. If shut down with the remote start button  
will remain in timer mode.  
the system  
5. The system will start every 3 hours until canceled by the  
brake, hood, or neutral safety shut-down wires.  
!
important Timer Mode should be used only in  
open areas. Never start and run the vehicle in an  
enclosed space such as a garage or carport.  
To exit timer mode, turn the ignition switch on any time the  
engine is running. The parking lights will flash 4 times, indicating  
timer mode has been exited.  
5. The system will start every 3 hours until canceled by the  
brake, hood, or neutral safety shut-down wires.  
IMPORTANT! Timer Mode should be used only  
in open areas. Never start and run the vehicle  
in an enclosed space such as a garage or  
carport.  
2005 Directed Electronics—all rights reserved  
17  
©
 
Starter Anti-Grind Circuitry  
Whenever the vehicle is remote started, advanced anti-grind cir-  
cuitry prevents the starter from engaging, even if the key is turned  
to the start position. This prevents damage to the starter motor if  
the key is turned to the start position during remote start operation.  
NOTE: Anti-grind circuitry only works when the remote start system is  
operating the motor and the Failsafe® Starter Kill relay is installed.  
Disabling the Remote Start System  
This feature allows your system's remote start unit to be tem-  
porarily disabled to prevent the vehicle from being remote started  
accidentally. This feature is useful if the vehicle is being serviced  
or stored in an enclosed area. To disable the remote start, move  
the shutdown toggle switch to the OFF position. The switch can  
be installed in a location of your choice. Check with your installer  
for recommended locations.  
LOCATION OF SHUTDOWN SWITCH_________________________  
18  
2006 Directed Electronics—all rights reserved  
©
 
Rapid Resume Logic  
This Directed Electronics system will store its current state to non-  
volatile memory. If power is lost and then reconnected the system  
will recall the stored state from memory. This means if the unit is  
in Valet Mode and the battery is disconnected for any reason, such  
as servicing the car, when the battery is reconnected the unit will  
still be in Valet Mode. This applies to all states of the system  
including arm, disarm, and Valet Mode.  
Programming Options  
Programming options control your system's normal, operational  
set-up. Most options do not require additional parts, but some may  
require additional installation labor. This system's programming  
options are listed below, with the factory default settings in bold:  
12, 24, or 60 minute run time. your system can be pro-  
grammed to allow the vehicle to run for 12, 24, or 60 min-  
utes when remote started.  
3, 6, 9, or 12 minute timer mode run time. Your system can  
be programmed to allow the vehicle to run for 3, 6, 9, or 12  
minutes when remote started in timer mode. Can be set up to  
16 minutes by your installer.  
19  
2006 Directed Electronics—all rights reserved  
©
 
Comfort closure is a programming option which closes the  
vehicle’s windows after remote locking.  
Parking lights flashing or constant. Your system can be pro-  
grammed to either flash or to turn on the parking lights con-  
stantly during the entire remote start operation.  
Passive Mode or Active Mode. In Passive Mode the Failsafe®  
Starter Kill will automatically activate 30 seconds after the  
ignition has been turned off.  
Ignition switch-controlled door-locking on or off. With this  
feature on, the doors will lock 3 seconds after the ignition  
key is turned on, and unlock when the ignition key is turned off.  
Passive Locking or Active Locking (doors lock only with the  
transmitter). With Passive Locking, the vehicle doors lock  
automatically 30 seconds after the ignition has been turned  
off. Passive Locking can only be selected when the system  
has been programmed for Passive Mode.  
The horn honk confirmations for locking and unlocking can be  
programmed on or off. In order for this feature to be pro-  
grammed on, the horn must be connected to the system.  
20  
2006 Directed Electronics—all rights reserved  
©
 
Glossary of Terms  
Control Unit: The “brain” of your system. Usually hidden under-  
neath the dash area of the vehicle. It houses the microprocessor  
which monitors your vehicle and controls all system functions.  
®
Failsafe Starter Kill: An automatic switch controlled by your sys-  
tem which prevents the vehicle’s starter from cranking whenever  
the system is armed. The vehicle is never prevented from cranking  
when the system is disarmed, in Valet Mode, or if the starter kill  
switch itself fails. Your system has feature-ready circuitry for the  
starter kill, however installation may require additional labor.  
LED: A blue light mounted at a discretionary location inside the  
vehicle. It is used to indicate the status of your system.  
Transmitter: A hand-held, remote control which operates the var-  
ious functions of your system.  
Valet Button: A small push button mounted at a discretionary  
location inside the vehicle. It is used to override the Failsafe®  
Starter Kill when a transmitter is lost or damaged, or to enter or  
exit Valet Mode.  
21  
2006 Directed Electronics—all rights reserved  
©
 
Convenience Expansions  
Listed below are some of the many expansion options available for  
use with your system. Some options may require additional parts  
and/or labor. Please consult with your dealer for a complete list of  
options available for use with this system.  
Domelight Supervision: The domelight will illuminate for 30  
seconds each time the system is disarmed using the transmitter.  
This is useful for seeing inside the vehicle at night prior to  
entering it.  
Power Door Lock Control: Your system is capable of controlling  
many types of power door lock systems; however, some door lock  
systems may require extra parts. Consult with your dealer to deter-  
mine which type of locks your vehicle uses. If power locks are  
connected, the system can be programmed to lock the doors auto-  
matically 30 seconds after the ignition has been turned off. The  
system can also be programmed to lock the doors when the ignition  
is turned on and to unlock them when the ignition is turned off.  
Power Trunk Release: The system’s auxiliary output can be pro-  
grammed to operate a factory power release for the vehicle's trunk  
or hatch. If the factory release is not power-activated, Directed  
Electronics 522T trunk-release solenoid can often be added.  
22  
2006 Directed Electronics—all rights reserved  
©
 
Power Window Control: Power window control is provided with  
Directed Electronics 529T or 530T systems. The 529T system will  
roll up two windows automatically when the system is armed, or  
roll two windows down by using the transmitter. The 530T will roll  
two windows both up and down. The 530T also provides one touch  
switch operation.  
Progressive Door Unlocking: For added security, your system can  
be configured to unlock the driver’s door only, leaving the pas-  
senger doors locked. Pressing the unlock button an additional time  
will unlock the passenger doors. This option requires additional  
parts and labor.  
Auxiliary Outputs Linked to Arm/Disarm/Remote Start: For  
added convenience the auxiliary outputs can be used to position  
the driver’s seat to a preset position on an Arm, Disarm, or Remote  
Start command from the remote.  
23  
2006 Directed Electronics—all rights reserved  
©
 
Notes  
24  
2006 Directed Electronics—all rights reserved  
©
 
Quick Reference Guide  
To arm using your remote  
To arm the system press  
for one second. The doors will lock (if con-  
nected). The LED will begin to flash. The vehicle’s horn (if connected)  
will honk and the parking lights will flash once to confirm arming.  
To disarm using your remote  
To disarm the system press  
for one second. The doors will unlock (if  
connected). The vehicle’s horn (if connected) will honk twice and the  
parking lights will flash twice.  
Disabling the Failsafe® Starter Kill without a transmitter  
Turn on the ignition. Press and release the Valet button within 10 sec-  
onds. The LED will stop flashing and the vehicle should start.  
To remote start the vehicle  
Press  
twice within 3 seconds. The parking lights will turn on (if con-  
nected) and the vehicle will start and run for the programmed duration.  
To enter or exit Valet Mode  
Turn the ignition to the "ON" position. Turn the ignition back off. Press  
and release the Valet button within 10 seconds. The status LED will light  
steadily if you have entered Valet Mode. To exit Valet Mode, repeat the  
steps above. The LED will turn off when exiting Valet Mode.  
To activate Panic Mode  
Press and hold  
for 1.5 seconds.  
To activate Timer Mode  
Press  
and  
to start the vehicle, and run it for the set duration.  
To activate Turbo Mode  
Park the vehicle and set parking brake. Remove your foot from the brake pedal  
and leave the engine running. Press and release the  
and  
buttons.  
To disable the remote start system  
To disable the remote start, move the shutdown toggle switch to the OFF  
position.  
Location of Shutdown Switch______________________________  
25  
2006 Directed Electronics—all rights reserved  
©
 
Valet Takeover  
Press and release  
on the transmitter twice in 3 seconds. Turn the  
ignition key to the OFF position. Once the vehicle has started, it will run  
for the pre-programmed period of time (12, 24, or 60 minutes).  
Rear Window Defogger  
Press the ,  
and  
buttons simultaneously to turn the defogger  
on or off when remote starting. When a remote start is initiated, the  
parking lights will flash 2-times if the defogger is set to off, and will  
flash 3-times if the defogger is set to on.  
 
The company behind this system is Directed Electronics  
Since its inception, Directed Electronics has had one purpose, to provide consumers  
with the finest vehicle security and car stereo products and accessories available. The  
recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic  
technology, Directed Electronics is ISO 9001 registered.  
Quality Directed Electronics products are sold and serviced throughout North America  
and around the world.  
Call (800) 274-0200 for more information about our products and services.  
Directed Electronics is committed to delivering world class quality products  
and services that excite and delight our customers.  
Directed Electronics  
Vista, CA 92081  
© 2006 Directed Electronics—all rights reserved  
G562VL 07-06  
 

Targus Mouse AMU41US User Manual
Telos Two Way Radio Zephyr Xport User Manual
Tiffen Camera Accessories Soft FX Warm Soft FX Filters User Manual
Trane Air Conditioner TCONT800AS11AA User Manual
Traulsen Refrigerator RHT132WPUT FHS User Manual
True Fitness Exercise Bike LC900 User Manual
Uniden Two Way Radio TR622 2 User Manual
ViewSonic Flat Panel Television VS12464 1G User Manual
Vizio TV Antenna M422i B1 User Manual
VXI Computer Hardware TC4XYY User Manual