Vinotemp Refrigerator VT 32BCSB User Manual

A P R O U D H E R I T A G E O F E X P E R I E N C E & Q U A L I T Y  
B e v e r a g e C o o l e r  
V T - 3 2 B C S B  
O W N E R ’ S  
M A N U A L  
W W W . V I N O T E M P . C O M  
 
Table of Contents  
PARTS AND SPECIFICATIONS...................................................... 4  
IMPORTANT SAFETY INSTRUCTIONS............................................. 5  
CORD INSTRUCTIONS................................................................ 6  
BEVERAGE COOLER INSTALLATION.............................................. 6  
TEMPERATURE CONTROL............................................................ 7  
REVERSAL OF DOOR SWING ....................................................... 8  
CLEANING AND CARE................................................................. 9  
MOVING YOUR BEVERAGE COOLER .............................................. 9  
TROUBLESHOOTING .................................................................10  
TERMS OF SALE AND WARRANTY................................................11  
SERVICE & IMPORTANT NOTICE..................................................12  
17631 S out h S usa na R oa d , R a ncho D om in gu ez, Ca lif or n ia 90221  
inf o@vino t em p . c om  
3
S N 3 2 B C H D 1 7 V T - S 1  
 
PARTS AND SPECIFICATIONS  
1. Glass Door  
2. Grill  
3. Adjustable Leveling Legs  
4. Shelf  
5. Cabinet  
6. PVC Control Panel  
7. LED Temperature Indicator  
8. Light Switch  
9. Temperature Adjustment Button  
Item Number  
VT-32BCSB  
Dimension (HxWxD) without handle  
34.4"×15.0"×22.7"  
Weight  
74 Lbs  
Power Consumption  
Cooling System  
1.8 kW.h/24h  
R134a  
Ambient Temp. Range  
Temperature Range  
6090°F  
4065°F  
Rated Voltage  
Rated Frequency  
Input Power  
115V  
60Hz  
120W  
4
W W W . V I N O T E M P . C O M  
S N 3 2 B C H D 1 7 V T - S 1  
 
IMPORTANT SAFETY INSTRUCTIONS  
When using an electrical appliance, basic precautions should be followed  
to reduce the risk of fire, electric shock, and personal injury.  
1. Use this appliance only as described in this manual. Other uses are  
not recommended and may cause fire, electric shock or injury.  
2. This product is intended for indoor, household use only.  
3. To protect against electric shock, do not immerse unit, plug or  
cord in water or other liquids. Avoid locating the unit in moist  
areas.  
4. Never allow children to operate, play with, or crawl inside the unit.  
5. Unplug from the outlet when not in use, when moving from one  
location to another, or before cleaning.  
6. To disconnect the appliance, grip the plug and pull it from the wall  
outlet. Never pull by the cord.  
7. Do not operate the appliance in the presence of explosive and/or  
flammable fumes.  
8. Do not place the appliance or any of its parts near an open flame,  
cooking or other heating appliance.  
9. Do not operate the appliance with a damaged cord or plug. If the  
product malfunctions, or if it is dropped or damaged in any  
manner, do not use.  
10. The use of attachments is not recommended and may be  
hazardous.  
11. Do not operate if the housing is removed or damaged.  
12. A loose fit plug may cause overheating and a distortion of the plug.  
Contact a qualified electrician to replace loose or worn outlet.  
13. This appliance is designed to be built-in (fully recessed) or free  
standing.  
14. The beverage cooler is intended for use in a controlled ambient  
location such that the ambient temperature does not exceed 90°F  
(32°C).  
15. Locate the unit away from direct sunlight and sources of heat  
(stove, heater, radiator, etc.). Direct sunlight may affect/alter the  
outside color of the appliance.  
WARNING: To reduce the risk of fire, electric shock or personal injury,  
unplug or disconnect the appliance from the power supply before  
servicing.  
WARNING: Risk of child entrapment. Before you throw away your old  
beverage cooler, take off the door and leave the shelves in place so that  
children may not easily climb inside.  
17631 S out h S usa na R oa d , R a ncho D om in gu ez, Ca lif or n ia 90221  
inf o@vino t em p . c om  
5
S N 3 2 B C H D 1 7 V T - S 1  
 
CORD INSTRUCTIONS  
For your protection, this unit should be properly  
grounded. Unit is equipped with a 3-conductor  
cord set that has a molded 3-prong grounding-  
type plug, and should be used in combination  
with a properly connected grounding-type outlet  
as shown in figure A.  
It is not recommended to use this beverage  
cooler with an extension cord or power board. Please ensure that the  
appliance is plugged directly into the electrical outlet.  
BEVERAGE COOLER INSTALLATION  
Remove the exterior and interior packaging before use.  
Check to be sure you have all of the parts and 1 owner’s manual.  
Place your beverage cooler on a flat, dry surface that is strong enough  
to support the unit when fully loaded.  
This unit is designed to be built-in (fully recessed) or free standing.  
Do not place heavy objects on top of the unit.  
Unit is not designed for installation in a garage, basement, or any  
other location where a controlled ambient environment between 60°  
and 90°F cannot be maintained.  
Do not place the unit in direct sunlight or near sources of heat.  
Extreme hot and cold ambient temperatures may cause the unit not to  
perform properly or increase electrical consumption.  
Do not place the unit next to a major appliance that emits large  
amounts of heat, such as a dishwasher, microwave, oven, etc.  
Do not plug unit into the same outlet as a refrigerator or microwave.  
Before connecting the appliance to the power source, let it stand  
upright for approximately 24 hours. This will reduce the possibility of a  
malfunction in the cooling system from handling during transportation.  
Clean the interior surface with lukewarm water using a soft cloth  
before first use.  
6
W W W . V I N O T E M P . C O M  
S N 3 2 B C H D 1 7 V T - S 1  
 
OPERATING INSTRUCTIONS  
1. Gently place/slide the racks into the beverage cooler.  
2. Determine the best temperature setting to use.  
3. Place bottles/cans inside the cooler.  
4. Plug the power cord into a standard grounded electrical outlet.  
5. Limit the frequency of opening the door to conserve energy and  
maintain proper storage temperature.  
6. You can turn the interior light on and off by touching the button  
labeled with a light on the control panel.  
Important: When using the beverage cooler for the first time, allow at  
least 24 hours for the internal temperature to adjust properly. Make sure  
there are at least 3 to 5 bottles in the unit.  
TEMPERATURE CONTROL  
Important: In order to operate efficiently, this product should be  
in an environment with an ambient temperature of less than 90°F  
(32°C).  
Temperature preset:  
For your convenience, the beverage cooler is programmed at storing  
temperature. The temperature pre-set by the manufacturer is 48°F (9°C).  
Setting the temperature:  
You can manually adjust the temperature. Simply press the “ ” button  
on the control panel to decrease the temperature and the “ ” button to  
increase the temperature by 1 degree increments inside the beverage  
cooler. The temperature range for this unit is from 40°F (4°C) to 65°F  
(18°C).  
When the cabinet temperature is too low, the LED will display “LL”. When  
the temperature is too high, it will display “HH”. The “ER” display shows  
when there has been a power disruption.  
17631 S out h S usa na R oa d , R a ncho D om in gu ez, Ca lif or n ia 90221  
inf o@vino t em p . c om  
7
S N 3 2 B C H D 1 7 V T - S 1  
 
REVERSAL OF DOOR SWING  
This beverage cooler is built with a reversible door. You have the choice of  
either opening it from the left or the right side. In order to reverse the  
opening direction of your door, please follow these simple instructions.  
.
CAUTION: To avoid personal injury to yourself and/or property,  
we recommend someone assist you during the door reversal  
process.  
1. Remove the top hinge assembly and  
keep for later use.  
2. Remove the plug buttons from the  
upper left holes and transfer them to  
the uncovered holes at the right side.  
Be sure to press the plug buttons  
firmly into the holes.  
3. Remove the door assembly and keep  
for later use.  
4. Remove the right bottom hinge and  
left bottom hinge and install them on  
the opposite sides.  
5. Re-install the door assembly with  
the door handle on the opposite side  
(Rotating the door assembly for  
180°). Make sure the door assembly  
is properly aligned on the cabinet.  
6. Re-install the top hinge assembly  
previously removed in step 1 on the  
opposite side and tighten the screws.  
The process is now complete.  
Note: 1. If desired, change the door swing before installation.  
2. Please remember, do not power up the unit for 48 hours after  
cooler has been out of an upright position to allow the coolants  
to settle inside the compressor.  
8
W W W . V I N O T E M P . C O M  
S N 3 2 B C H D 1 7 V T - S 1  
 
CLEANING AND CARE  
Always unplug the beverage cooler before cleaning.  
Do not use benzene, scrubbing brushes or chemical cleaners as these  
will damage the unit.  
Use only a mild, nonabrasive cleanser to clean the exterior of the  
cabinet.  
Clean the stainless steel door and handle by wiping with a warm water  
and baking soda solution. The solution should be about 2 tablespoons  
of baking soda to a quart of water.  
Wash the racks with a mild detergent solution.  
Always dry all parts with a clean dry cloth before plugging the  
beverage cooler back into the receptacle.  
MOVING YOUR BEVERAGE COOLER  
Always unplug the beverage cooler before moving.  
Always remove all beverages before moving the beverage cooler.  
Securely tape down all loose items (shelves) inside your appliance.  
Turn the leveling legs up to the base to avoid damage.  
Tape the door shut.  
Be sure the beverage cooler stays in the upright position during  
transportation  
Protect the outside of appliance with a blanket or similar item when  
moving as needed.  
17631 S out h S usa na R oa d , R a ncho D om in gu ez, Ca lif or n ia 90221  
inf o@vino t em p . c om  
9
S N 3 2 B C H D 1 7 V T - S 1  
 
TROUBLESHOOTING  
You can solve many common beverage cooler problems easily, saving you  
the cost of a possible service call. Try the suggestion below to see if you  
can solve the problem before contacting Vinotemp at [email protected].  
SYMPTOM  
Door will not  
close properly.  
POSSIBLE CAUSE  
The beverage cooler is not level.  
The shelves are out of position.  
The door was reversed and not properly installed.  
The door gasket is dirty.  
Unit does not  
operate—does  
not have power  
Check that unit is plugged into the wall socket.  
Make sure the wall socket has power. If outlet is  
controlled by a wall switch, make sure switch is set to  
on. Test wall socket functionality by testing another  
electrical appliance in the power socket.  
Make sure there are at least 3 to 5 bottles in the unit.  
When using the unit for the first time, it can take up  
to 24 hours to reach the desired temperature.  
If the room temperature is above 90°F (32°C), the  
unit will not get below 51°F (11°C). Humidity does  
not affect the cooling ability of the unit.  
To achieve accurate temperature control, the unit  
should not be used or operated in any of the  
following locations:  
Power is ON but  
the unit will not  
cool.  
o In a sunny place  
o In a room with poor air circulation such as a  
garage near another heat-producing appliance  
such as a dishwasher, oven or refrigerator.  
o With an outlet shared with a refrigerator, as the  
refrigerator will drain power from the beverage  
cooler.  
o In a cabinet or closet.  
Make sure the cooling vents are not obstructed.  
This is simply a function of the cooling system. The  
lower the setting, the more the fan will run. If the  
room is warmer than 90°F (32°C), it will run more.  
The unit has been designed to run continuously when  
operating at the lower temperatures.  
Fan is always  
running.  
Vibrations  
Check to make sure the beverage cooler is level.  
10  
W W W . V I N O T E M P . C O M  
S N 3 2 B C H D 1 7 V T - S 1  
 
TERMS OF SALE AND WARRANTY  
Vinotemp International (“Seller”) and the person or entity that acquires these goods from Seller (“Purchaser”)  
hereby fully agree to the following terms and conditions of the sale: Shipping fees are the responsibility of the  
Purchaser whether freight prepaid or freight collect. Seller assumes no responsibility for the goods sold to the  
Purchaser once the goods have left the Seller’s premises, including, but not limited to, late delivery by the  
moving carrier, or for events caused by any difficulty carrier incurs in attempting to fit the goods into the  
Purchaser’s place of business or residence due to the size of the goods or otherwise. Purchaser assumes all  
responsibility for delivery, payment of freight, access, measurement, installation, hook-up, wiring, moving and  
storage of the goods. The transportation of all goods is subject to the terms and conditions which the moving  
carrier imposes on Purchaser including, but not limited to, additional charges imposed per flight of stairs,  
and/or additional charges resulting from the carrier’s inability to safely and/or adequately use the building  
elevator to lift the goods to an upper floor. Any claim for damages incurred during shipment by the carrier of  
the goods are insured and handled directly with the carrier. Any damages due to manufacture defects will be  
handled directly with Vinotemp International, subject to the limited warranty.  
All sales are final, and unless authorized in writing by the Seller, Purchaser may not return the goods, under  
any circumstance. If Purchaser refuses to accept the goods, under any circumstance, the Purchaser is liable for  
the return and cost of freight both ways, and if Seller does take back the goods, there will be a restocking  
charge that is 35% of the purchase price of the goods. Purchaser must notify Seller of non-conforming goods  
within four days of delivery, after which time all goods are deemed accepted.  
If Purchaser tenders payment with a check that has insufficient funds (NSF), or stops payment on a check or  
credit card for any reason, Purchaser agrees to pay for all costs associated with the Seller’s connection or  
litigation of such a claim, including without limitation extra damages, court costs and attorneys’ fees. Finance  
charges begin the date of invoice. Collection fees plus NSF fee of $50 will be added to your invoice, which you  
agree to promptly pay. Title to the goods does not pass until payment is received in full by Seller and Seller  
retains a security interest in the goods until they are paid for in full.  
LIMITED WARRANTY: Seller warrants that the goods will be free of defects in materials and workmanship as  
follows: Metal cabinet wine, beverage, refrigerator and freezer units: parts and labor for cooling system and  
cabinetry for a period of 12 (twelve) months from date of sale, removal and re-installation of unit is not  
included in warranty. For a scratch and dent or refurbished unit, warranty is 3 months from your dated invoice  
(parts for function only, not cosmetic). There is no warranty on parts purchased separately. Purchaser’s  
exclusive remedy is limited, at Seller’s option; to repair or replace defective part[s] with either new or factory  
reconditioned part[s]. Purchaser is responsible for shipping the unit pre-paid to designated facility and Seller  
will pay return shipping charges in the continental United States for items repaired under warranty within 12  
months from date of sale. Improper placement of the unit will void the warranty. This limited warranty does  
not cover damage due to such things as accident, misuse, abuse, mishandling, neglect, acts of God, fires,  
earthquakes, floods, high winds, government, war, riot or labor trouble, strikes, lockouts, delay of carrier,  
unauthorized repair, or any other cause beyond the control of the Seller, whether similar or dissimilar to the  
foregoing. Seller is not responsible for any damages caused to Seller’s property resulting from the good. This  
limited warranty applies only inside the Continental US. (Alaska, Puerto Rico and Hawaii are not warranted).  
Purchaser understands and acknowledges that the goods sold here are beverage coolers and/or other similar  
units which house beverage. Purchaser assumes all risk of using these units, including risk of spoilage,  
humidity variations, temperature variations, leaks, fire, water damage, mold, mildew, dryness and similar and  
any other perils that might occur.  
Seller is not responsible for incidental or consequential damages, and there are no warranties, expressed or  
implied, which extend beyond the Limited Warranty described above. The implied warranties of merchantability  
and of fitness for a particular purpose are hereby expressly disclaimed. Some states do not allow the exclusion  
of incidental or consequential damages, or a waiver of the implied warranties of fitness and/or merchantability,  
so the above limitations may not apply to you. This warranty gives you specific legal rights and you may also  
have other rights which vary from state to state.  
In the event of any dispute between Seller and Purchaser arising out of or relating to these terms and  
conditions or to the goods sold generally, Purchaser must first file a written claim with Seller within ten days of  
the occurrence giving rise to the claim and wait an additional thirty days for a response before initiating any  
legal action. The sale and all terms are subject to California law. Any legal proceeding arising out of or relating  
to these terms and conditions or to the goods sold generally shall be brought solely and exclusively in the  
County of Los Angeles. In no event may Purchaser initiate any legal proceeding more than six months after the  
occurrence of the event giving rise to the dispute.  
The above terms and conditions are the only ones governing this transaction and Seller makes no oral  
representations of any kind. These Terms and Conditions can only be modified in writing, signed by both  
Purchaser and Seller. 07/08  
17631 S out h S usa na R oa d , R a ncho D om in gu ez, Ca lif or n ia 90221  
inf o@vino t em p . c om  
11  
S N 3 2 B C H D 1 7 V T - S 1  
 
SERVICE & IMPORTANT NOTICE  
Upon receipt and inspection of unit, the supply cord must be replaced if it is  
damaged. Contact our customer service at 1-800-777-8466 or  
The manufacturer has a policy of continuous improvement on its products  
and reserves the right to change materials and specifications without notice.  
WARNING:  
Please do not place the unit within reach of children.  
For adult use only.  
Contact [email protected] with any questions or visit:  
17631 S. Susana Road  
Rancho Dominguez, CA 90221  
Vinotemp is a registered trademark of Vinotemp International. All products, features, and services are subject  
to change without notice. We cannot guarantee the accuracy of the contents of this document. We disclaim  
liability for errors, omissions, or future changes.  
© 2008 Vinotemp International. All rights reserved.  
 

Teledex Cordless Telephone Cordless Handset User Manual
The Singing Machine Karaoke Machine STVG888W User Manual
Tiger Games 66874 User Manual
Topfield Satellite TV System TF 6000 FE User Manual
Tripp Lite Surge Protector TLM626 User Manual
Valcom Speaker V 1220 User Manual
VTech Baby Toy 91 009642 000 User Manual
VTech Cordless Telephone 6031 User Manual
Weed Eater Lawn Mower 163600 User Manual
Weed Eater Lawn Mower WE16542E User Manual