Vinotemp Ice Maker VT IMSW User Manual

A P R O U D H E R I T A G E O F E X P E R I E N C E & Q U A L I T Y  
I C E M A K E R  
V T - I M S W  
O W N E R ’ S  
M A N U A L  
W W W . V I N O T E M P . C O M  
 
IMPORTANT SAFETY INSTRUCTIONS  
To reduce the risk of fire, electrical shock or injury when using  
your appliance, follow these basic precautions:  
Do not operate this or any other appliance with a damaged cord.  
Connect to properly polarized outlets only. No other appliance should be  
plugged into the same outlet. Be sure that the plug is fully inserted into the  
receptacle.  
Do not run cord over carpeting or other heat insulators; do not cover cord.  
Keep cord away from trafficked areas.  
We do not recommend the use of an extension cord, as it may overheat and  
become a fire risk.  
Always unplug the appliance before cleaning it or making repairs.  
Exercise caution and use reasonable supervision when appliance is used near  
children. Never allow children to operate, play with or crawl inside the  
appliance.  
Do not clean appliance with flammable fluids. Do not store or use gasoline or  
other flammable vapors and liquids in the vicinity of this or any other appliance.  
The fumes can create a fire hazard or explosion.  
Do not use solvent-based cleaning agents or abrasives on the interior. These  
cleaners may damage or discolor the interior.  
Do not operate with housing panels removed.  
Intended for indoor household use only.  
When disposing of refrigerated appliances, special handling is often required. It  
is the consumer’s responsibility to comply with federal and local regulations  
when disposing of this product.  
To ensure proper ventilation for your appliance, the front of the unit must be  
completely unobstructed. For use in a controlled ambient location such that the  
ambient temperature does not exceed 90°F (32°C) and is not below 60°F  
(16°C).  
Do not attempt to repair or replace any part of your appliance unless it is  
specifically recommended in this manual. All other servicing should be referred  
to a qualified technician.  
Locate the unit away from direct sunlight and sources of heat (stove, heater,  
radiator, etc).  
To protect against electric shock, do not immerse appliance, plug or cord in  
water or other liquids. Avoid locating the unit in moist areas.  
Do not use this appliance for other than its intended purpose.  
WARNING: Risk of child entrapment and suffocation. Before you throw away  
this or an old unit, take off the door. Leave the shelves in place, so that  
children may not easily climb inside.  
1 7 6 2 1 S o u t h S u s a n a R o a d , R a n c h o D o m i n g u e z , C a l i f o r n i a 9 0 2 2 1  
i n f o @ v i n o t e m p . c o m  
3
 
ELECTRICAL CONNECTION  
Improper use of the grounded plug can result in the risk of  
electrical shock. If the power cord is damaged, have it  
replaced by an authorized service center.  
z
z
This unit should be properly grounded for your safety. The power cord of this  
unit is equipped with a three-prong plug which mates with standard three  
prong wall outlets to minimize the possibility of electrical shock.  
Do not under any circumstances cut or remove the third ground prong from  
the power cord supplied. For personal safety, this appliance must be properly  
grounded.  
z
z
z
The cord should be secured behind the unit and not left exposed or dangling to  
prevent accidental injury.  
Never unplug the unit by pulling the power cord. To disconnect the appliance,  
always grip the plug firmly and pull straight out from the wall outlet.  
Repair or replace immediately all power cords that have become frayed or  
otherwise damaged. Do not use a cord that shows cracks or abrasion damage  
along its length or at either end. When moving the unit, be careful not to  
damage the power cord.  
Extension Cord  
z
It is not recommended to use this appliance with an extension cord or power  
board. Please ensure that the appliance is plugged directly into the electrical  
outlet.  
4
W W W . V I N O T E M P . C O M  
 
PARTS AND SPECIFICATIONS  
1. Body  
2. Door  
3. Door Gasket  
4. Grill  
5. On/Off Switch  
6. Ice Basket  
Model No.  
VT-IMSW  
Power (Voltage/Frequency)  
Rated Current  
115V/60Hz  
1.7A  
Power Input  
105W  
Power Consumption  
Refrigerant  
1.2 kW.h/24h  
R134a  
Volume  
28L  
Ambient Temperature Range  
Dimensions (W x D x H)  
60°F - 90°F  
15" x 18" x 25"  
1 7 6 2 1 S o u t h S u s a n a R o a d , R a n c h o D o m i n g u e z , C a l i f o r n i a 9 0 2 2 1  
i n f o @ v i n o t e m p . c o m  
5
 
INSTALLATION INSTRUCTIONS  
Before Using Your Ice Maker  
Remove all exterior and interior packing materials.  
Check to be sure you have all of the following parts:  
1 Ice Bucket  
1 Plastic Scoop  
25 ft. hose  
1 instruction manual  
Before connecting the ice maker to the power source, let it stand upright for  
approximately 2 hours. This will reduce the possibility of a malfunction in the  
cooling system from handling during transportation.  
Clean the interior surface and ice bucket with lukewarm water using a soft cloth.  
Installation Of Your Ice Maker  
This appliance is designed to be recessed or built-in (fully recessed) or  
freestanding.  
Place your ice maker on a flat surface that is strong enough to support the unit  
when fully loaded.  
Level your ice maker by adjusting the legs at the front of the unit.  
Do not place the unit in a moist place. Too much moisture in the air will cause frost  
to form quickly on the evaporator, requiring more frequent defrosting of the  
appliance.  
Locate the ice maker away from direct sunlight and sources of heat (stove, heater,  
radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may  
increase electrical consumption. Extreme cold ambient temperatures may also  
cause the ice maker not to perform properly.  
Position appliance to allow airflow through the front grill (see  
SKETCH 1)  
SKETCH 1  
Connecting the Water Supply  
Improper water line connection may result in flooding. You  
must use a licensed plumber. Review state and local plumbing  
codes before installation.  
Not all of the hardware necessary for installation has been provided. It is necessary  
to hire a professional licensed plumber to complete the installation.  
Connect tubing (supplied with the unit) to the nearest cold water source. Connect  
sufficient tubing to the unit to allow the appliance to be moved freely for cleaning  
and service. Also, make sure that the tubing is not pinched or damaged during  
transportation and installation.  
6
W W W . V I N O T E M P . C O M  
 
OPERATING YOUR ICE MAKER  
Initial Start-Up Operation  
1. Make sure the unit is properly installed by a licensed plumber.  
2. Make sure the On/Off switch is in the “OFF” position.  
3. Plug the appliance into a standard/grounded electrical outlet.  
4. Place the On/Off switch in the “ON” position.  
5. Make sure the water supply is on. As soon as the inner mechanism of the ice maker  
reaches the proper temperature, the ice maker mold will fill with water.  
6. The first ice cubes may be small, because of air initially in the water line. Later ice  
cubes will be of standard crescent mood type and size.  
7. Approximate time for the first cycle is 30-40 minutes.  
8. Each cycle takes approximately 140 ML of water; you should have a full ice bucket  
after 11 hours.  
IMPORTANT: Discard all ice cubes made during the first 3 hours of operation.  
Ice Maker General Operation  
When the ice bucket is full, the ice making mechanism will  
automatically shut off. However, the system will continue to cool and  
maintain the cube supply as needed.  
Ice delivery may be interrupted by raising the metal arm into an  
upright position (see SKETCH 2)  
If the ice maker is not used regularly, it is recommended that the ice  
bucket be emptied periodically to ensure ice freshness.  
Sometimes the cubes may appear cloudy. This is not cause for  
concern and is not related to the taste of your ice cubes chemical  
make-up of the water.  
SKETCH 2  
1 7 6 2 1 S o u t h S u s a n a R o a d , R a n c h o D o m i n g u e z , C a l i f o r n i a 9 0 2 2 1  
i n f o @ v i n o t e m p . c o m  
7
 
CARE AND MAINTENANCE  
Cleaning Your Ice Maker  
Turn the control to "OFF", unplug the appliance, and remove the ice bucket.  
Wash the inside surfaces with a warm water and baking soda solution. The solution  
should be about 2 tablespoons of baking soda to a quart of water.  
Wash the ice bucket with a mild detergent solution.  
Wash the outside of the ice maker with warm water and mild liquid detergent. Rinse  
well and wipe dry with a clean soft cloth.  
The condenser coils should be vacuumed when they become dusty or dirty. Keep front  
grill free of dust and lint to permit free airflow.  
WARNING: Failure to unplug the ice maker before cleaning could result in electrical  
shock or personal injury.  
Defrosting Your Ice Maker  
Ice maker should be defrosted approximately every 4-6 weeks or when frost on the ice  
maker is excessive (¼” thick or thicker). To defrost, turn the unit off, remove ice cubes,  
and keep door open at least two inches. You may want to put a towel down to soak up any  
water drainage caused by defrosting the unit.  
Power Failure  
Most power failures are corrected within a few hours and should not affect the  
temperature of your ice maker if you minimize the number of times the door is opened. If  
the power is going to be off for a longer period of time, you need to take the proper steps  
to disconnect your appliance.  
Vacation Time/Storage  
Shut off the water supply at the main water valve.  
Disconnect the water supply line from valve.  
Allow unit to run for an hour or two until all remaining ice cubes have been ejected.  
Disconnect unit from main power source.  
Dry out excess water from ice maker interior.  
Leave the door open at least two inches.  
Moving Your Ice Maker  
Remove any remaining ice.  
Securely tape down all loose items remaining inside your ice maker.  
Tape the door shut.  
Be sure the ice maker stays secure in an upright position during transportation. Also,  
protect outside of ice maker with a blanket or similar item as needed.  
Energy Saving Tips  
Locate your ice maker in the coolest area of the room, away from heat-producing  
appliances or heating ducts and out of direct sunlight.  
Minimize the length and frequency of opening the ice maker door.  
8
W W W . V I N O T E M P . C O M  
 
TROUBLESHOOTING GUIDE  
You can solve many common problems easily, saving you the cost of a possible service call.  
Try the suggestions below to see if you can solve the problem before contacting Vinotemp.  
PROBLEM  
Ice maker does not power  
on  
POSSIBLE CAUSE  
Not plugged in.  
A tripped circuit breaker or a blown fuse.  
Ice maker control switch is set in “OFF” position.  
Airflow to front grill is blocked  
Ice maker arm was set in the “OFF” position  
Water supply is turned off  
Water line is crimped; water is not reaching unit  
Ice maker has excessive frost build up  
Room temperature is warmer than normal.  
Appliance door is open too often.  
Ice maker is on but not  
producing ice  
Compressor turns on and  
off frequently  
Door is not closed completely.  
Door gasket does not seal properly.  
Ice maker does not have adequate ventilation. Check  
to ensure that the grill is unobstructed and condenser  
coils are clean.  
Excessive vibrations  
Check to assure that the ice maker is level. Adjust the  
leveling legs as needed.  
A rattling noise may come from the flow of the  
refrigerant; this is normal.  
As each cycle ends, you may hear gurgling sounds  
caused by the flow of refrigerant in your appliance.  
Contraction and expansion of the inside walls may  
cause popping and crackling noises.  
Ice maker is not level.  
Ice maker is not leveled.  
Door was reversed and not properly installed.  
Door gasket is dirty.  
The ice bucket is out of proper position.  
Ice maker door is opened too often  
Ice maker seems to make  
too much noise  
Door will not close properly  
Ice cubes are melted  
together  
1 7 6 2 1 S o u t h S u s a n a R o a d , R a n c h o D o m i n g u e z , C a l i f o r n i a 9 0 2 2 1  
i n f o @ v i n o t e m p . c o m  
9
 
TERMS OF SALE AND WARRANTY  
Vinotemp International (“Seller”) and the person or entity that acquires these goods from Seller (“Purchaser”)  
hereby fully agree to the following terms and conditions of the sale: Shipping fees are the responsibility of the  
Purchaser whether freight prepaid or freight collect. Seller assumes no responsibility for the goods sold to the  
Purchaser once the goods have left the Seller’s premises, including, but not limited to, late delivery by the  
moving carrier, or for events caused by any difficulty carrier incurs in attempting to fit the goods into the  
Purchaser’s place of business or residence due to the size of the goods or otherwise. Purchaser assumes all  
responsibility for delivery, payment of freight, access, measurement, installation, hook-up, wiring, moving and  
storage of the goods. The transportation of all goods is subject to the terms and conditions which the moving  
carrier imposes on Purchaser including, but not limited to, additional charges imposed per flight of stairs, and/or  
additional charges resulting from the carrier’s inability to safely and/or adequately use the building elevator to lift  
the goods to an upper floor. Any claim for damages incurred during shipment by the carrier of the goods are  
insured and handled directly with the carrier. Any damages due to manufacture defects will be handled directly  
with Vinotemp International, subject to the limited warranty.  
All sales are final, and unless authorized in writing by the Seller, Purchaser may not return the goods, under any  
circumstance. If Purchaser refuses to accept the goods, under any circumstance, the Purchaser is liable for the  
return and cost of freight both ways, and if Seller does take back the goods, there will be a restocking charge  
that is 35% of the purchase price of the goods. Purchaser must notify Seller of non-conforming goods within four  
days of delivery, after which time all goods are deemed accepted.  
If Purchaser tenders payment with a check that has insufficient funds (NSF), or stops payment on a check or  
credit card for any reason, Purchaser agrees to pay for all costs associated with the Seller’s connection or  
litigation of such a claim, including without limitation extra damages, court costs and attorneys’ fees. Finance  
charges begin the date of invoice. Collection fees plus NSF fee of $50 will be added to your invoice, which you  
agree to promptly pay. Title to the goods does not pass until payment is received in full by Seller and Seller  
retains a security interest in the goods until they are paid for in full.  
LIMITED WARRANTY: Seller warrants that the goods will be free of defects in materials and workmanship as  
follows: Metal cabinets and similar compressor-based systems including wine, beverage, refrigerator, beer  
dispensers, ice makers, and freezer units: parts and labor for cooling system and cabinetry for a period of 12  
(twelve) months from date of sale, removal and re-installation of unit is not included in warranty. For a scratch  
and dent or refurbished unit, warranty is 3 months from your dated invoice (parts for function only, not  
cosmetic). There is no warranty on parts purchased separately. Purchaser’s exclusive remedy is limited, at  
Seller’s option; to repair or replace defective part[s] with either new or factory reconditioned part[s]. Purchaser is  
responsible for shipping the unit pre-paid to designated facility and Seller will pay return shipping charges in the  
continental United States for items repaired under warranty within 12 months from date of sale. Improper  
placement of the unit will void the warranty. This limited warranty does not cover damage due to such things as  
accident, misuse, abuse, mishandling, neglect, acts of God, fires, earthquakes, floods, high winds, government,  
war, riot or labor trouble, strikes, lockouts, delay of carrier, unauthorized repair, or any other cause beyond the  
control of the Seller, whether similar or dissimilar to the foregoing. Seller is not responsible for any damages  
caused to Seller’s property resulting from the good. This limited warranty applies only inside the Continental US.  
(Alaska, Puerto Rico and Hawaii are not warranted).  
Purchaser understands and acknowledges that the goods sold here are beer dispensers and/or other similar units  
which house beverages. Purchaser assumes all risk of using these units, including risk of spoilage, humidity  
variations, temperature variations, leaks, fire, water damage, mold, mildew, dryness and similar and any other  
perils that might occur.  
Seller is not responsible for incidental or consequential damages, and there are no warranties, expressed or  
implied, which extend beyond the Limited Warranty described above. The implied warranties of merchantability  
and of fitness for a particular purpose are hereby expressly disclaimed. Some states do not allow the exclusion of  
incidental or consequential damages, or a waiver of the implied warranties of fitness and/or merchantability, so  
the above limitations may not apply to you. This warranty gives you specific legal rights and you may also have  
other rights which vary from state to state.  
In the event of any dispute between Seller and Purchaser arising out of or relating to these terms and conditions  
or to the goods sold generally, Purchaser must first file a written claim with Seller within ten days of the  
occurrence giving rise to the claim and wait an additional thirty days for a response before initiating any legal  
action. The sale and all terms are subject to California law. Any legal proceeding arising out of or relating to  
these terms and conditions or to the goods sold generally shall be brought solely and exclusively in the County of  
Los Angeles. In no event may Purchaser initiate any legal proceeding more than six months after the occurrence  
of the event giving rise to the dispute.  
The above terms and conditions are the only ones governing this transaction and Seller makes no oral  
representations of any kind. These Terms and Conditions can only be modified in writing, signed by both  
Purchaser and Seller. 07/08  
10  
W W W . V I N O T E M P . C O M  
 
 
SERVICE & IMPORTANT NOTICE  
Upon receipt and inspection of unit, the supply cord must be replaced if it is  
damaged. Contact our customer service at 1-800-777-8466 or  
The manufacturer has a policy of continuous improvement on its products and  
reserves the right to change materials and specifications without notice.  
WARNING:  
Please do not place the unit within reach of children.  
For adult use only.  
Contact [email protected] with any questions or visit  
17621 S. Susana Road  
Rancho Dominguez, CA 9022  
Vinotemp is a registered trademark of Vinotemp International. All products, features, and services are subject to  
change without notice. We cannot guarantee the accuracy of the contents of this document. We disclaim liability  
for errors, omissions, or future changes.  
© 2009 Vinotemp International. All rights reserved.  
 

Teledyne Carbon Monoxide Alarm GFC7001T User Manual
Tiger Games 1 2 3 Tri Language Learner User Manual
Toastmaster Convection Oven HFS09 User Manual
Toastmaster Popcorn Poppers TPC3 User Manual
Toshiba Cash Register MA 1650 4 User Manual
Triarch Indoor Furnishings 33124 User Manual
Tricity Bendix Dishwasher TDS 200 User Manual
Tyco Baby Toy 7054 User Manual
Ultra electronic Printer Prima 3 User Manual
Vulcan Hart Fryer 1ER50A User Manual