VENTILATION
Designer Built-In Wall Hoods
Standard Features & Accessories
All models include
• Must also purchase interior or exterior
air, and are easily removed for quick
cleaning (frame and mesh are
stainless steel for durability and long
life)
• See Dimensions & Specifications
table for number of filters (and
spacers) per model
o Design of low-profile filter system
means less interior hood space to
be cleaned
o Canopy interior is completely lined
in stainless steel for increased
rigidity, seamless appearance, and
easy cleaning
• 50-watt halogen lights with dimmer
control
o Power switch and dimmer control
are separate, allowing you to leave
dimmer at favorite position
o See Dimensions & Specifications
table for number of lights per model
DTWS models include
• 9"H.
• Adjustable duct cover (for 8 – 9’
ceilings) shipped standard (see
Dimensions & Specifications table)
o Finish matches canopy exterior
DTWN models include
• 18"H.
• Duct covers must be ordered
separately (see Installation Notes &
Accessories)
ventilator kit, sold separately (see
Installation Notes & Accessories for
recommended Viking ventilator
products
• 24”D.(tests show 24”D. hoods
perform properly over 27”D. ranges)
• Heat sensor turns the ventilator on full
power when cooking temperatures
reach uncomfortable levels
• Variable speed controls for custom
venting—separate on/off switch allows
you to leave ventilator at
favorite/most-used setting
• 12-hour timer built into ventilator
controls
• Delay feature allows you to set the
ventilator to shut off on its own from
10 – 30 minutes later
• Heavy-duty construction; elegant
design, and styling
o Virtually seamless stainless steel
design with no visible screws
• Easy cleanup
o Dishwasher-safe, stainless steel
mesh filters efficiently remove
grease and heated vapors from the
Model numbers
SLIM TRADITIONAL WALL HOODS
• DTWS3049—30"W.
• DTWS3649—36"W.
• DTWS4249—42"W.
• DTWS4849—48"W.
TALL TRADITIONAL LEGDELESS WALL
HOODS
• DTWN3048—30"W.
• DTWN3648—36"W.
• DTWN4248—42"W.
• DTWN4848—48"W.
Slim Traditional Wall Hoods should not
be installed over Professional cooking
products with the gas Char-Grill feature.
A 1,200 or 1,500 CFM (if applicable)
ventilator kit should be used when
installed over ranges/rangetops with gas
grill.
Model Options
DTWS Slim Traditional
Wall Hood*
DTWN Tall Traditional
Ledgeless Wall Hood**
FINISH DETAILS FOR ALL MODELS
EXTRA FINISH DETAILS FOR DTWS
• Stainless Steel (SS), Black (BK), White
(WH), Metallic Silver (MS), Graphite Gray
(GG), Stone Gray (SG), Taupe (TP), Biscuit
(BT), Cotton White (CW), Oyster Gray
(OG), Golden Mist (GM), Lemonade (LE),
Sage (SA), Mint Julep (MJ), Sea Glass (SE),
Iridescent Blue (IB), Viking Blue (VB),
Pumpkin (PM), Racing Red (RR), Apple
Red (AR), Burgundy (BU), Plum (PL),
Chocolate (CH), and Cobalt Blue (CB).
• Finish designates exterior of canopy
• Stainless Steel (SS) canopy interior
MODELS ONLY
• Accessory Rail—along front of canopy
(must be ordered and factory installed)
• Stainless Steel/Chrome (CR)—Stainless
steel rail with chrome supports/brackets
and hooks (included)
• Brass Trim Option (BR)—nameplate, rail,
supports/brackets, and hooks (included).
Brass components have a durable
protective coating for maintenance-free
normal use.
*Shown throughout with adjustable duct cover, included.
**Shown throughout with duct cover, sold separately.
See Installation Notes & Accessories for duct cover model numbers and ship weights.
ORDERING INSTRUCTIONS
First specify model number, followed by color code (DTWS3049SS). Specify decorative rail code at end (DTWS3049SSCR).
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Designer Built-In Wall Hoods
Dimensions & Specifications
CLEARANCE DIMENSIONS
66”min.
30”min.
(167.6 cm)
(76.2 cm)
to
72”max.
to
(91.4 c
36”max.
(182.9 cm)
m)
36”
(91.4 cm)
SLIM TRADITIONAL
WALL HOOD
66”min.
(167.6 cm)
30”min.
to
72”max.
(76.2 c
(182.9 cm)
m)
to
36”max.
(91.4 cm)
36”
(91.4 cm)
TALL TRADITIONAL
LEDGELESS WALL HOOD
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Designer Built-In Wall Hoods
Installation Requirements
DTWS Slim Traditional
Wall Hood
DTWN Tall
Traditional Ledgeless
Wall Hood
UTILITY REQUIREMENTS
Proper installation/ducting is extremely
o Straight runs and gradual
turns are best; for example,
each 90° elbow is equivalent
to 5’ – 10’ (1.52 – 3.05 cm) of
straight run.
• 7” (17.8 cm) round duct for
300 – 600 CFM; 10” for 900 –
1500 CFM
o Never use flexible duct; it
creates back pressure/air
turbulence and greatly
reduces performance.
ELECTRICAL
• Hardwire direct with two-wire
ground
important to ensure maximum
performance. Use a qualified and
trained installer.
• 120 VAC/60 Hz
• Max. amp usage (rating
includes recommended
ventilator kit rating)—see
Dimensions & Specifications
table
DUCTING
• Check with a qualified and
trained installer or local codes
for makeup air requirements, if
any.
• Max. duct run length
o For 300 – 1,200 CFM—50’
(152.4 m)
PLUMBING
Not applicable
o For 1,500 CFM—75’ (22.9 m)
GAS
Not applicable
o For general reference only;
for longer duct runs, increase
duct size and contact a
qualified and trained installer.
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be greatly
overstated.
Model
Ventilator Kits
Duct Size
Max. Amps
Interior
1.7/3.2
1.7/3.2
3.2
Interior
Exterior
DEV900
Interior
Exterior
Exterior
6.6
DTWS3049
DTWS3649
DTWS4249
DTWS4849
DTWN3048
DTWN3648
DTWN4248
DTWN4848
DIV300/440
DIV300/440
DIV440
7” (17.8 cm)
7” (17.8 cm)
7” (17.8 cm)
10” (25.4 cm)
7” (17.8 cm)
7” (17.8 cm)
7” (17.8 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
10” (25.4 cm)
DEV900
6.6
DEV900
6.6
DIV880
DEV1200/1500**
VEV900/1200*
VEV900/1200*
VEV900/1200*
VEV1200/1500**
5.6
4.3/5.1
6.6/3.9
6.6/3.9
6.6/3.9
4.3/5.1
VIV300/600/1200*
VIV300/600/1200*
VIV600/1200*
VIV1200*
2.4/4.6/6.6
2.4/4.6/6.6
4.6/6.6
7.0
* A 1,200 CFM interior- or exterior-power ventilator should be used when installed over range/rangetop with gas char-grill.
** It is recommended that the 1,500 CFM ventilator be used with longer duct runs.
Note: Maximum amp rating for hoods includes recommended ventilator kit rating. All products must be hard wired with two-wire ground. An interior- or
exterior-power ventilator kit must be purchased for installation with all 18”H. hoods.
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Designer Built-In Wall Hoods
Installation Notes & Accessories
✪
Ventilator Kits
• See Installation Requirements table for recommendations for each hood model
• A 1,200 CFM interior or 1,500 CFM exterior (if applicable) ventilator should be used over ranges/rangetops with gas grill
• Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty
Kit model
DIV300
Description
Hood models
DTWS3049/3649
Approx. ship wt. lbs. (kg)
15 (6.8)
300 CFM interior power
440 CFM interior power
880 CFM interior power
900 CFM exterior power
1200 CFM exterior power
1500 CFM exterior power
300 CFM interior power
600 CFM interior power
1200 CFM interior power
900 CFM exterior power
1200 CFM exterior power
1500 CFM exterior power
DIV440
DTWS3049/3649/4249
DTWS4849
25 (11.3)
DIV880
36 (16.2)
DEV900
DEV1200
DEV1500
VIV300
DTWS3049/3649/4249
DTWS3649/4249/4849
DTWS4849
39 (17.6)
53 (23.9)
47 (21.3)
DTWN3048/3648
27 (12.2)
VIV600
DTWN3048/3648/4248
DTWN3048/3648/4248/4848
DTWN3048/3648/4248
DTWN3048/3648/4248/4848
DTWN4848
27 (12.2)
VIV1200
VEV900
VEV1200
VEV1500
43 (19.4)
39 (17.6)
53 (23.9)
47 (21.3)
Duct Covers
• DCW for DTWN models
o 12”H./12”D.
o Extend height of hood by 12”; conceal duct
• Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), and Graphite Gray (GG).
o When ordering, specify finish code following accessory model number (for example, DCSB3008-SS)
Model
DCW30
DCW36
DCW42
DCW48
Description
Approx. ship wt. lbs. (kg)
Duct cover for 30”W. DTWN
Duct cover for 36”W. DTWN
Duct cover for 42”W. DTWN
Duct cover for 48”W. DTWN
10 (4.5)
11 (5.0)
13 (5.9)
14 (6.3)
Duct Cover Extensions
• For use with DTWS Slim Traditional Wall Hoods
• Extends height of hood by up to 12” (for 10’ ceilings)
• Replaces adjustable duct cover supplied with hood
• Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), and Graphite Gray (GG).
o Specify finish code following accessory model number (for example, DCCE1010-SS)
Model
Description
Approx. ship wt. lbs. (kg)
DCCE1010
DCCE1210
DCCE2010
Duct cover extension (for 30”W. DTWS hood)
Duct cover extension (for 36” & 42”W. DTWS hoods)
Duct cover extension (for 48”W. DTWS hood)
4 (1.8)
6 (2.7)
9 (4.1)
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Designer Built-In Wall Hoods
Installation Notes & Accessories
✪
Backsplashes
• Stainless Steel (SS)
• 30”H.
• Backsplashes protect the wall space below hood
• Create a continuous finish between cooking surface and hood
• Low maintenance, easy to clean
• Hemmed edges with screw holes
• Kit includes backsplash and fastening screws
Model
BKS30
BKS36
BKS42
BKS48
Description
Approx. ship wt. lbs. (kg)
7 (3.2)
30”W. backsplash
36”W. backsplash
42”W. backsplash
48”W. backsplash
9 (4.1)
12 (5.4)
14 (6.3)
Warming Shelf Panels
• Stainless Steel (SS)
• 12”D./12”H.
• Shelf panels hold cookware and condiments
• Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash
• 15-7/8”W. X 10-1/8”D.
• Kit includes shelf (or shelves) and fastening screws
Model
WGP30
WGP36
WGP42
WGP48
Description
Approx. ship wt. lbs. (kg)
9 (4.1)
30”W. warming shelf panels (one shelf)
36”W. warming shelf panels (two shelves)
42”W. warming shelf panels (two shelves)
48”W. warming shelf panels (two shelves)
12 (5.4)
14 (6.3)
16 (7.2)
Compliance Information
WARRANTY SUMMARY*
• One-year full warranty—complete product
• Five-year limited warranty—all ventilator motors
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items
*Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty. For complete warranty see Use & Care Guide.
Warranty valid on Viking products shipped within the United States and Canada.
PLANNING AND DESIGN GUIDE
RELEASED 12/1/07
©2007 VRC— INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
|