VENTILATION
Built-In Classic Chimney Glass Wall Hood
Standard Features & Accessories
All models include
•
Recommended for use with 30” and
36”W. non-griddle/grill ranges, 30” and
36”W. non-griddle/grill rangetops, and
30” and 36”W. cooktops
•
•
•
Advanced, electronic push-button
controls with LED display
Delay feature allows you to set the
ventilator to shut off on its own
Easy cleanup
o Dishwasher-safe, stainless steel mesh
filters efficiently remove grease and
heated vapors from the air, and are
easily removed for quick cleaning
(frame and mesh are stainless steel)
• See Dimensions & Specifications
table for number of filters per model
o Design of low-profile filter system
means less interior hood space to be
cleaned
•
Heavy-duty construction; sleek,
contemporary design and styling
o Virtually seamless stainless steel
design with no visible screws
•
•
Adjustable duct cover (for 8 – 9’
ceilings) ships standard with hood
Heat sensor turns the ventilator on full
power when cooking temperatures
reach uncomfortable levels
•
•
Variable speed 450 CFM blower ships
standard for custom venting—allows
you to leave ventilator at favorite/most-
used setting
May be converted for non-ducted
recirculation (accessory kit sold
separately)
•
Two 20-watt halogen lights with
dimmer control. (bulbs included)
Model Options
DGWH Designer
Chimney Glass Wall Hood
FINISH DETAILS
• Stainless Steel (SS)
ORDERING INSTRUCTIONS
First specify model number, followed by color code (DGWH3042SS).
P L A N N I N G A N D D E S I G N G U I D E
R E L E A S E D 1 1 / 1 1 / 0 8
© 2 0 0 8 V R C — INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Built-In Classic Chimney Glass Wall Hood
Dimensions & Specifications
CLEARANCE DIMENSIONS
DGWH Designer
Chimney Glass Wall Hood
6
5
0
2
”
(
m
c
1
i
n
.
.
4
o
m
2
4
”
t
6
)
6
”
m
(
m
6
(
1
i
1
n
6
a
.
0
.
7
x
.
.
)
c
6
m
c
t
m
)
m
3
7
o
0
”
(
a
6
x
.
2
.
c
m
)
”
6
)
3
m
c
4
.
1
9
(
CHIMNEY WALL HOOD
Note: For best performance and safe, efficient operation, it is recommended that the bottom of the hood be 24” (61.0 cm) to
30” (76.2 cm) above the countertop.
P L A N N I N G A N D D E S I G N G U I D E
R E L E A S E D 1 1 / 1 1 / 0 8
© 2 0 0 8 V R C — INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Built-In Classic Chimney Glass Wall Hood
Installation Requirements
DGWH Designer
Chimney Glass Wall Hood
UTILITY REQUIREMENTS
Proper installation/ducting is extremely
important to ensure maximum
performance. Use a qualified and
trained installer.
• 6” round duct
o Never use flexible duct; it
creates back pressure/air
turbulence and greatly
reduces performance.
DUCTING
• 450 CFM interior (blower
included)
GAS
Not applicable
• Check with a qualified and
trained installer for local codes
and makeup air requirements,
if any.
• Max. duct run length—50’
(152.4 m)
ELECTRICAL
• Hardwire direct with two-wire
with ground
• 120 VAC/60 Hz
o Duct run length is for general
reference only; for longer
duct runs, increase duct size
and contact a qualified and
trained installer.
• Max. amp usage—3.13
PLUMBING
Not applicable
o Straight runs and gradual
turns are best; for example,
each 90” elbow is equivalent
to 5’ – 10’ (1.52 – 3.05 cm) of
straight run.
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be greatly
overstated.
Model
Interior Ventilator Kits
Interior Duct Size
Interior Max. Amps
DGWH3646
450 CFM Standard
6” (15.2 cm)
3.13
P L A N N I N G A N D D E S I G N G U I D E
R E L E A S E D 1 1 / 1 1 / 0 8
© 2 0 0 8 V R C — INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
VENTILATION
Built-In Classic Chimney Glass Wall Hood
Installation Notes & Accessories
%
Recirculating Hood Conversion Kits
• For DGWH only
• Eliminates ducting
• Kit includes
o Charcoal filter
o Installation hardware
o Top vent/grille
• Air diverter
• Reducing collar
Model
Description
Approx. ship wt. lbs. (kg)
DGRK36
36”W. glass hood
3 (1.1)
Duct Cover Extensions
• For DGWH only
• 11-1/2”W. x 12”D. x 36”-56”H.
• Extends height of hood by up to 12” (for 10’ ceilings)
• Replaces adjustable duct cover supplied with hood
• Specify finish code following accessory model number (for example, DGCE1210-SS)
• Available in Stainless Steel (SS)
Model
Description
Approx. ship wt. lbs. (kg)
DGCE1210
Designer glass duct cover extension
12 (5.4)
Compliance Information
WARRANTY SUMMARY*
• One-year full warranty—complete product
• Five-year limited warranty—all ventilator motors
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items
*Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty. For complete warranty see Use & Care Guide.
Warranty valid on Viking products shipped within the United States and Canada.
P L A N N I N G A N D D E S I G N G U I D E
R E L E A S E D 1 1 / 1 1 / 0 8
© 2 0 0 8 V R C — INFORMATION SUBJECT TO CHANGE
V I K I N G R A N G E . C O M
•
1 - 8 8 8 - V I K I N G 1
|