Viking Refrigerator FWCI1240 User Manual

Use & Care Manual  
Viking Range, LLC  
111 Front Street  
Greenwood, Mississippi 38930 USA  
(662) 455-1200  
For product information  
call 1-888-845-4641, or visit online in the  
15”W./24”W.  
Undercounter Refrigeration  
F20867C EN  
(070113)  
 
Electronic Controls  
Important Safety Instructions  
Before beginning, please read these instructions completely and  
carefully.  
DO NOT remove permanently affixed labels, warnings, or plates  
from the product. This may void the warranty.  
• Please observe all local and national codes and ordinances.  
• Please ensure that this product is properly grounded.  
• The installer should leave these instructions with the consumer who  
should retain for local inspectors use and for future reference.  
Displays target set point  
Activates Sabbath Mode  
WARNING  
To reduce the risk of fire, electric shock, or injury when using your unit, follow  
these basic precautions:  
Increases temperature when changing set  
• Read all instructions before using the unit.  
point; Shows maximum stored temperature  
when pressed alone.  
• Never allow children to operate, play with, or crawl inside the unit.  
• Never clean unit parts with flammable fluids. The fumes can create a fire  
hazard or explosion.  
• Always turn the power off to change light bulbs, clean, or service the  
unit.  
Decreases temperature when changing set  
point; Shows minimum stored temperature  
when pressed alone.  
FOR YOUR SAFETY  
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS  
AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.  
THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.  
On/Off Switch  
Light Switch  
It is your responsibility to be sure your undercounter refrigeration unit is:  
• located so the front is not blocked to restrict incoming or discharge air  
flow.  
• properly leveled.  
• located in a well ventilated area.  
• connected to the proper kind of outlet, with the correct electric supply  
and grounding. A 115V, 60 Hz, 15 amp fused electrical supply is  
required. Note: Time delay fuse or circuit breaker is recommended.  
• not used by anyone unable to operate it properly.  
• used only for its intended purpose.  
LED Indicators  
LED  
FUNCTION  
Cooling ON  
An alarm is occurring  
(See troubleshooting for alarm codes)  
• properly maintained.  
Light ON  
°C/°F  
Measurement Unit  
WARNING  
State of California Proposition 65 Warning  
• This product contains one or more chemicals know to the State of  
California to cause cancer.  
• This product contains one or more chemicals know to the State of  
California to cause birth defects or other reproductive harm.  
•SAVE THESE INSTRUCTIONS•  
4
5
 
Electronic Controls  
Electronic Controls  
Temperature Control Panel  
The controller is located inside of the unit. The display will read  
OFF when the unit is off and will show temperature when the  
unit is ON.  
To convert from Fahrenheit to Celsius:  
1. Open door and hold F/C button for 3 seconds.  
2. The unit will shut down briefly and then restart displaying  
the opposite temperature scale.  
IMPORTANT: The LED display is reading actual air temperature  
not product temperature. Under these conditions, an air  
temperature swing does not change the actual product  
temperature. Product temperature remains at a very stable  
temperature.  
3. Repeat step 1 to convert back to original setting.  
Sabbath Mode  
To activate SABBATH mode, open door and pres SAB button.  
If display lighting was activated, it will remain activated. Turn  
off display lighting before initiating Sabbath Mode if display  
light will not be used.  
Product Temperature Set Points and Ranges  
All Refrigerator  
Refrigerated Drawer  
Beverage Center  
Wine Center  
38°F  
38°F  
42°F  
55°F  
Range: 32°F to 39°F  
Range: 32°F to 39°F  
Range: 32°F to 48°F  
Range: 44°F to 68°F  
When in Sabbath mode:  
• The display will be switched off (with the exclusion of the  
measurement temperature icon LED);  
• The regulation will keep on working normally;  
• The digital inputs will be deactivated (they will not work  
during SABBATH MODE);  
• After any alarm condition the display will be switched on,  
coming back to the OFF mode at the end of the alarm  
condition;  
To view the SET point:  
1. Press and release the SET button. The display will show the  
set point value.  
2. Press and release the SET button or wait for 5 seconds to  
display the actual temperature again.  
To change the SET point:  
1. Press the SET button for 3 seconds to change the set point  
value.  
2. The value of the set point will be displayed and the “°C” or  
“°F” LED will start blinking.  
3. To change the set point value, press the UP or DOWN  
buttons within 10 seconds.  
• The keyboard will be deactivated with the exclusion of the  
SAB button.  
To exit the SABBATH mode, open door and press SAB button.  
Close door. The display and light will turn on.  
4. To store the new set point value, press the SET button  
again or wait 10 seconds.  
To lock the control:  
1. Press the UP+DOWN buttons simultaneously for 3 seconds.  
2. The “PoF” message will be displayed and the keyboard will  
be locked. At this point it will only be possible to see  
the set point, the MAX or the MIN temperature stored.  
3. If a button is pressed more than 3 seconds, the “PoF”  
message will be displayed.  
To unlock the control:  
1. Press the UP and DOWN buttons simultaneously for 3  
seconds until the “Pon” message is displayed.  
6
7
 
Using the Unit  
Using the Unit  
Loading Product  
IMPORTANT: Before storing perishables, allow unit to run for a  
minimum of 24 hours to allow temperature stabilization after  
start-up.  
To remove  
brackets,  
remove shelf,  
lift front of  
bracket to  
disengage the  
front key slot,  
and pull  
forward to  
disengage the  
rear key slot.  
When loading items into unit, do no block internal louvers and  
fan guard openings or performance will be decreased.  
Shelving  
IMPORTANT: To achieve maximum performance, interior louver  
openings and fan guard openings should never be obstructed.  
All Refrigerator  
The single door unit comes standard with two adjustable, full  
extension, pullout shelves. Shelving positions are adjustable.  
Press tabs and  
pull out shelf  
Wine Center  
The single door unit comes standard with five full extension  
black vinyl coated wine racks capable of storing 20 total wine  
bottles (15” models) or 40 total wine bottles (24” models).  
Shelves are removable and adjustable to accommodate  
oversized (magnum) bottles.  
CAUTION  
Completely empty the drawer before removing.  
Removing drawers from Refrigerated Drawer Unit  
Full-extension Drawers – Pull the drawer out to its farthest  
point. Locate the tabs in the middle on both sides of the  
extenders. Press left tab up and right tab down; pull drawer  
out. To return drawer, first push both extenders completely in  
then line up the shelf grooves and slide easily into the unit.  
Beverage Center  
The single door unit comes standard with two full extension  
black vinyl coated wine racks and one full extension pullout  
shelf allowing for storage of both wine and beverages. Shelving  
positions are adjustable.  
Adjusting Full Extension Shelving  
1. Pull the shelf out to its farthest position. Locate the tabs in  
the middle of both extenders. Press left tab up and right tab  
down and pull shelf out.  
2. Reposition each bracket separately. Grasp the middle of the  
bracket, pull the front end up and out, then forward to remove.  
3. Place bracket at the desired position. Push the rear hook into  
the rear key slot. Set front of bracket on the wall hook.  
4. Repeat for other bracket(s).  
5. Push extenders completely into the unit. Align the shelf  
grooves with the extenders and slide completely into the unit.  
8
9
 
Wine Rack Finishing  
Wine Rack Finishing  
Wooden Rack Trim Finishing  
24”W. Wooden Wine Rack Trim Design  
All wine racks come with unfinished solid hardwood fronts  
which can be replaced with other wood to match your  
cabinetry. See following illustrations for wine rack face details.  
8-17/32”  
(21.7 cm)  
8-17/32”  
(21.7 cm)  
4-1/64”  
(1.6 cm)  
The unfinished faces may be finished and sealed. In many cases  
stains and/or finishes have odors that may be objectionable in  
an enclosed area. To remove the front wood-face from the wine  
shelf, simply pull out the wine shelf and remove the fasteners,  
finish as desired and re-install with fasteners.  
8”  
(20.3 cm)  
7-1/4”  
(18.4 cm)  
1-17/32”  
(3.9 cm)  
33/64”  
(1.3 cm)  
5/8”  
(1.6 cm)  
A
15”W. Wooden Wine Rack Trim Design  
4-1/32”  
(10.2 cm)  
4-1/32”  
(10.2 cm)  
2
NOTE:  
LIP AND SPUR DRILL BIT  
ARE ACCEPTABLE  
DETAIL A  
SCALE 1.5 : 1  
4-1/64”  
(1.6 cm)  
1/8” (0.3 cm) TYP  
33/64”  
(1.3 cm)  
1/16”  
(0.2 cm)  
TYP  
1
3/8”  
(1.0 cm)  
B
1/4”  
(0.6 cm)  
2
NOTE:  
LIP AND SPUR DRILL BIT  
ARE ACCEPTABLE  
DETAIL B  
SCALE 1.5 : 1  
1/4”  
(0.6 cm)  
45°  
1
3/8”  
(1.0 cm)  
1
3/8”  
(1.0 cm)  
1/8” (0.3 cm) TYP  
1/16”  
(0.2 cm)  
TYP  
1
3/8”  
1/4”  
BREAK ALL OUTSIDE  
EDGES.  
(1.0 cm)  
BREAK ALL  
OUTSIDE  
EDGES.  
(0.6 cm)  
1-1/2”  
(3.8 cm)  
1/4”  
(0.6 cm)  
45°  
18-21/64”  
(46.6 cm)  
1-1/2”  
(3.8 cm)  
9-21/64”  
(23.7 cm)  
10  
11  
 
Interior Light  
Checking Product Temperature  
To accurately check the temperature of the product stored in a  
refrigerated compartment, insert an accurate thermometer into  
a plastic (non-breakable) bottle, partially filled with water.  
Tighten the bottle cap securely.  
Interior Light  
The unit is equipped with an interior light that is illuminated  
when the door is opened. The cabinet also comes standard  
with a display light function located on the control panel for  
displaying your products through a glass door. To use display  
lighting, press the Light button. The light icon on the display  
will go from flashing to continuous. Do not use the display  
light function with a solid door product. If the display light is  
left on for an extended period of time, it may increase the  
cabinet temperature, especially at the top and cause the  
refrigeration system to run longer. To turn off display lighting,  
open door and press the Light button. The light icon on the  
display will go from continuous to flashing.  
Place the bottle in the desired area for 24 hours. Refrain from  
opening the unit during the testing period. After 24 hours,  
check the temperature of the water. Adjust the control settings  
if necessary and re-test.  
Your units are pre-set in order to achieve the recommended  
temperature range when installed in a 70°F ambient room  
temperature. Factors, which affect the internal temperatures of  
the refrigerated cabinet, include:  
Light Bulb Replacement  
NOTE: Please contact your Viking Range parts distributor or  
dealer to order the LED light bulb.  
Temperature setting  
• Room temperature where installed  
• Number of times the door is opened and closed  
• Length of times the door is opened and closed  
• Length of times the door is left open  
• Style of door installed  
To replace light bulb, unscrew the bulb counterclockwise and  
replace with new bulb.  
• Door gasket sealing and condition  
• Amount of time the internal light is illuminated  
• Installation in direct sun light or near a heat source  
12  
13  
 
Winterizing Outdoor Units  
Preparing for Spring Use  
This process should occur when the daily low temperature is at  
or below the set point temperature in the unit.  
This process should occur when the daily low temperature is at  
or above the set point temperature in the unit.  
1. Turn unit to OFF position by pressing the OFF button  
on the controller. The controller displays the word OFF  
(If power cord is accessible, unplug the cabinet. If not,  
turn off the circuit breaker to the receptacle the cabinet  
is plugged into.)  
2. Remove all contents from the unit.  
3. Remove the kickplate from the unit.  
4. Clean the condensor by using a vacuum cleaner  
to remove the loose debris (dirt, leaves, etc.) that may  
have gotten inside the kickplate.  
5. Reattach the kickplate.  
6. Clean the interior using Stainless Steel Cleaner and  
Polish.  
7. Clean the exterior using Stainless Steel Cleaner and  
Polish.  
1. Plug the unit into the electrical receptacle.  
2. Press the OFF button one time to turn the unit ON. The  
controller will read the actual temperature inside the  
unit on the display. It will soon begin the cooling  
process to bring the unit to the set temperature.  
3. Remove the kickplate from the unit.  
4. Check the condensing unit to ensure it is clear of loose  
debris, clean as necessary with vacuum cleaner.  
5. Reattach the kickplate to the unit.  
6. Clean the interior using Stainless Steel Cleaner and  
Polish.  
7. Clean the exterior using Stainless Steel Cleaner and  
Polish.  
NOTE: Do not place a cover over the unit.  
NOTE: While not required, you may choose to remove the unit  
from the outdoor location and store indoors.  
WARNING  
Leaving your product operating in temperatures lower than those  
recommended will void the warranty.  
14  
15  
 
Troubleshooting  
Cleaning  
Before Calling for Service  
Cleaning  
If the unit appears to be malfunctioning, read through  
NORMAL OPERATION first. If the problem persists, check the  
TROUBLESHOOTING GUIDE. Locate the problem in the guide  
and refer to the cause and its remedy before calling for service.  
The problem could be something, which can be solved without  
a service call.  
To clean stainless steel exterior or interior surfaces, use a soft,  
non-abrasive stainless steel cleaner to wipe down these  
surfaces. Glass door panels can be cleaned using any standard  
glass cleaner available on the market today.  
To clean interior and exterior non-metallic surfaces and  
removable parts, wash with a mild solution of soap and  
lukewarm water with a little baking soda. Rinse and dry  
thoroughly. Avoid getting water on lights, controllers, fan  
motors, and unfinished wood wine rack faces.  
WARNING  
ELECTROCUTION HAZARD!!  
Never attempt to repair or perform maintenance on the unit until the main  
electrical power has been disconnected.  
CAUTION  
DO NOT use abrasive cleaners or cloths on any of the interior or exterior  
surfaces or removable parts.  
Problem  
No interior light  
Solution  
• Check to ensure bulb is tight.  
• Check to ensure bulb is not burned out.  
Condenser Cleaning  
Light stays on when  
door is closed  
• Manual ON/OFF light switch is turned ON.  
• Check to ensure door switch is making  
contact with door.  
WARNING  
For cleaning the condenser and other routine maintenance, shut off  
electricity to the unit.  
Noise during  
operation  
• Certain sounds are normal. Soft sounds  
from the compressor, fan motor and valves  
will be heard.  
In all instances, you should clean the condenser area every  
three months. The condenser is located behind the kickplate.  
To clean the condenser remove the kickplate and use a soft  
bristle brush and vacuum to remove dust and lint. Avoid  
damaging or crushing the condenser fins or tubing. Upon  
completion, re-install the kickplate.  
Controller display is  
flashing “P1”  
• There is a thermostat probe failure.  
Controller display is  
flashing “HA”  
• The internal compartment temperature has  
exceeded the high temperature alarm  
preset value for over 30 minutes.  
• Check to ensure door is closed.  
• Check for door gasket seal.  
CAUTION  
• Product was just installed.  
Failure to clean the condenser could result in temperature loss or  
mechanical failure or damages. Clean this area every three months.  
• Check to ensure condenser is clean.  
• Check to ensure kickplate is unobstructed.  
• Surrounding ambient temperature has  
changed dramatically.  
• Check to ensure interior light is OFF.  
16  
17  
 
Troubleshooting  
Troubleshooting (cont.)  
Problem  
Solution  
Problem  
Solution  
The refrigeration  
system runs for long  
periods of time  
• Check to ensure the condenser area is  
clean and free of obstructions.  
• Check to ensure the door has not been  
open for a long time or more frequent door  
openings aren’t occurring.  
• Check to ensure warm product hasn’t just  
been placed in the cabinet.  
• On hot days and in warm room  
temperatures the system will run long.  
Controller display is  
flashing “DA”  
• The door has been left ajar.  
• Check to ensure door is closed.  
Controller display is  
flashing “LA”  
• The internal compartment temperature has  
exceeded the low temperature alarm preset  
value for over 30 minutes.  
• Check to ensure door is closed.  
• Check for door gasket seal.  
• Surrounding air temperature has changed  
dramatically.  
Condensation forms  
inside the refrigerated  
compartments  
• This is normal during high humidity and  
frequent door openings.  
• Check to ensure door is closed and sealing  
properly.  
Controller display is  
flashing “EE”  
• The controller has a data or memory failure.  
The refrigerated  
• Check to ensure there is electrical power to  
cabinet isn’t running  
the unit.  
Condensation forms  
on the outside of the  
unit  
• During periods of high humidity some  
condensation might appear on outside  
surfaces. The condensation will disappear  
when the humidity drops. Meanwhile, be  
sure doors are closing and sealing properly.  
If condensation persists, contact your  
local authorized servicer.  
• Check to ensure your home circuit breaker  
or fuse is on.  
• Check to ensure your ON/OFF key pad is  
on.  
• Check to ensure your condenser area is  
clean.  
The refrigerated  
compartment is  
warmer than usual  
• Check to ensure your control is set properly.  
• Check to ensure the light is not staying on.  
• Check to ensure your condenser area is  
clean and free of obstructions.  
• Check to ensure the door has not been  
open for a long time or more frequent door  
openings aren’t occurring.  
• Check to ensure the internal louvers and fan  
guard openings aren’t obstructed.  
• Check to ensure warm product hasn’t just  
been placed in the cabinet.  
When pressing the UP • If the UP button is pressed without pressing  
button, the display  
shows a “Hi” message  
followed by a  
temperature that does  
not match the set  
point.  
the SET button, the MAX stored  
temperature will be displayed. Press the UP  
button again or wait 5 seconds for the  
normal temperature to be displayed. To  
reset the MAX temperature, press and hold  
the SET button until the message “rSt”  
starts blinking. Release the SET button and  
the new stored value will be the current  
temperature. Frequent and/or extended  
door openingsmay cause a higher than  
expected MAX temperature.  
The refrigerated  
compartment is  
colder than usual  
• Check to ensure your control is set properly.  
• Check to ensure your door is closing and  
sealing properly.  
• Check to ensure the ambient temperature is  
within the normal operating range.  
When pressing the  
DOWN button, the  
display shows a “Lo”  
• If the DOWN button is pressed without  
pressing the SET button, the MIN stored  
temperature will be displayed. Press the  
message followed by a DOWN button again or wait 5 seconds for  
temperature that does  
not match the set  
point.  
the normal temperature to be displayed. To  
reset the MIN temperature, press and hold  
the SET button until the message “rSt”  
starts blinking. Release the SET button and  
the new stored value will be the current  
temperature.  
18  
19  
 
Service & Registration  
Warranty  
If service is required after checking the troubleshooting guide, call your  
dealer or authorized service agency. The name of the authorized  
service agency can be obtained from the dealer or distributor in your  
area.  
VRCI/VBCI/VWCI/VRDI UNDERCOUNTER REFRIGERATION WARRANTY  
(INDOOR MODELS)  
THREE YEAR FULL WARRANTY  
Undercounter refrigeration and all of their components and accessories, except as detailed below*,  
are warranted to be free from defects in material or workmanship under normal household use for a  
period of three (3) years from the date of original retail purchase. Viking Range, LLC  
warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective  
during the warranty period  
When you make a service call, be sure to have the following  
information handy:  
• Model Number  
• Serial Number  
• Date of Purchase  
*FULL NINETY (90) DAY COSMETIC WARRANTY: Painted and decorative items are warranted to  
be free from defective materials or workmanship for a period of ninety (90) days from the date of  
original retail purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN  
NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.  
• Name of dealer from whom purchased  
†FULL NINETY (90) DAY WARRANTY IN "RESIDENTIAL PLUS" APPLICATIONS: This full  
warranty applies to applications where use of the product extends beyond normal residential use,  
but the warranty period for products used in such applications is ninety (90) days. Examples of  
applications covered by this warranty are bed and breakfasts, fire stations, private clubs, churches,  
yachts, etc. Under this "Residential Plus" warranty, the product, its components and accessories  
are warranted to be free from defective material or workmanship for a period of ninety (90) days  
from the date of original retail purchase. This warranty excludes use of the product in all  
commercial locations such as restaurants, food service locations and institutional food service  
locations.  
If you are unable to obtain the name of an authorized service agency,  
or if you continue to have service problems, contact Viking Range, LLC  
at (888) 845-4641 or write to:  
SIX YEAR FULL WARRANTY  
VIKING RANGE, LLC  
PREFERRED SERVICE  
111 Front Street  
Greenwood, Mississippi 38930 USA  
Any sealed refrigeration system component, as listed below, is warranted to be free from defective  
materials or workmanship in normal household use during the fourth through the sixth year from  
the date of original retail purchase. Viking Range, LLC warrantor, agrees to repair or  
replace, at its option, any part which fails or is found to be defective during the warranty period.  
Sealed Refrigeration System Components: Compressor, Evaporator, Condenser, Connecting  
Tubing, Dryer/Strainer  
TWELVE YEAR LIMITED WARRANTY  
Any sealed refrigeration system component, as listed above, which fails due to defective materials or  
workmanship in normal household use during the seventh through the twelfth year from the date of original  
retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other  
costs, including labor.  
Record the following information indicated  
below. You will need it if service is ever  
required. The model and serial number for  
your undercounter refrigeration unit are  
located in the top right under the control  
housing.  
Model and  
Serial number  
LIMITED LIFETIME WARRANTY  
During the life of the product, any stainless steel parts found to be defective in material or  
workmanship will be repaired or replaced, free of charge for the part itself, with the owner paying  
all other costs, including labor. This warranty excludes surface corrosion or rust, scratches,  
discoloration, water or atmospheric conditions, or cleaning practices which are part of normal  
residential use.  
TERMS AND CONDITIONS  
Model No. _________________________________________________________________________  
Serial No. ___________________________________________________________________________  
Date of Purchase __________________________________________________________________  
Date Installed ______________________________________________________________________  
Dealers Name _____________________________________________________________________  
Address _____________________________________________________________________________  
________________________________________________________________________________________  
This warranty extends to the original purchaser of the product warranted hereunder and to each  
transferee owner of the product during the term of the warranty and applies to products purchased and  
located in the United States, Canada, Mexico, and the Caribbean (excluding Cuba, Dominican Republic,  
and Haiti). Products must be purchased in the country where service is requested. If the product or one  
of its component parts contains a defect or malfunction during the full warranty period after a reasonable  
number of attempts by the warrantor to remedy the defect or malfunction, the owner is entitled to either  
a refund or replacement of the product or its component part or parts. Replacement of a component  
part includes its free installation, except as specified under the limited warranty. Under the terms of this  
warranty, service must be performed by a factory authorized Viking Range, LLC service agent or  
representative. Service will be provided during normal business hours, and labor performed at overtime  
or premium rates shall not be covered by this warranty.  
Owner shall be responsible for proper installation, providing reasonable and necessary maintenance,  
providing proof of purchase upon request, and making the appliance reasonably accessible for service.  
The return of the Owner Registration Card is not a condition of warranty coverage. You should, however,  
return the Owner Registration Card so that Viking Range, LLC can contact you should any question of  
safety arise which could affect you.  
This warranty gives you specific legal rights, and you may also have other rights which may vary from  
jurisdiction to jurisdiction.  
WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from  
abuse, failure to provide reasonable and necessary maintenance, accident, delivery, negligence, natural  
disaster, loss of electrical power to the product for any reason, alteration, outdoor use, improper  
installation, improper operation, or repair or service of the product by anyone other than an authorized  
Viking Range, LLC service agency or representative. This warranty does not apply to commercial usage.  
If service requires installation of parts, use only authorized parts to  
insure protection under the warranty.  
Keep this manual with your refrigerator for future reference.  
20  
21  
 
Warranty  
Warranty  
VRCO/VRDO UNDERCOUNTER REFRIGERATION WARRANTY  
LIMITATION OF REMEDIES AND DURATION OF IMPLIED WARRANTY  
OWNER’S SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS  
PRODUCT SHALL BE THE REMEDIES SET FORTH ABOVE. VIKING RANGE, LLC IS NOT  
RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE, INCLUDING BUT NOT LIMITED  
TO FOOD OR MEDICINE LOSS, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH  
OF WARRANTY, BREACH OF CONTRACT OR OTHERWISE. Some jurisdictions do not allow the  
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusions may  
not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE  
PERIOD OF COVERAGE OF THE APPLICABLE EXPRESS WRITTEN LIMITED WARRANTIES SET  
FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the  
above limitation may not apply to you.  
(OUTDOOR MODELS)  
TWO YEAR FULL WARRANTY  
Undercounter refrigeration and all of their components and accessories, except as detailed below*,  
are warranted to be free from defects in material or workmanship under normal household use for a  
period of two (2) years from the date of original retail purchase. Viking Range, LLC  
warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective  
during the warranty period  
*FULL NINETY (90) DAY COSMETIC WARRANTY: Painted and decorative items are warranted to  
be free from defective materials or workmanship for a period of ninety (90) days from the date of  
original retail purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN  
NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.  
WARRANTY SERVICE  
To obtain warranty service, contact an authorized Viking Range, LLC service agent, or Viking Range, LLC,  
111 Front Street, Greenwood, Mississippi 38930, (888) 845-4641. Provide model and serial number and  
date of original purchase or closing date for a new construction. For the name of your nearest authorized  
Viking Range, LLC service agency, call Viking Range, LLC. IMPORTANT: Retain proof of original purchase  
to establish warranty period.  
†FULL NINETY (90) DAY WARRANTY IN "RESIDENTIAL PLUS" APPLICATIONS: This full  
warranty applies to applications where use of the product extends beyond normal residential use,  
but the warranty period for products used in such applications is ninety (90) days. Examples of  
applications covered by this warranty are bed and breakfasts, fire stations, private clubs, churches,  
yachts, etc. Under this "Residential Plus" warranty, the product, its components and accessories  
are warranted to be free from defective material or workmanship for a period of ninety (90) days  
from the date of original retail purchase. This warranty excludes use of the product in all  
commercial locations such as restaurants, food service locations and institutional food service  
locations.  
Specifications subject to change without notice.  
FIVE YEAR LIMITED WARRANTY  
Any sealed refrigeration system component, as listed above, which fails due to defective materials  
or workmanship in normal household use during the second through the fifth year from the date of  
original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner  
paying all other costs, including labor.  
LIMITED LIFETIME WARRANTY  
During the life of the product, any stainless steel parts found to be defective in material  
or workmanship will be repaired or replaced, free of charge for the part itself, with the  
owner paying all other costs, including labor. This warranty excludes surface corrosion  
or rust, scratches, discoloration, water or atmospheric conditions, or cleaning practices  
which are part of normal residential use.  
TERMS AND CONDITIONS  
This warranty extends to the original purchaser of the product warranted hereunder and to each  
transferee owner of the product during the term of the warranty and applies to products purchased and  
located in the United States, Canada, Mexico, and the Caribbean (excluding Cuba, Dominican Republic,  
and Haiti). Products must be purchased in the country where service is requested. If the product or one  
of its component parts contains a defect or malfunction during the full warranty period after a reasonable  
number of attempts by the warrantor to remedy the defect or malfunction, the owner is entitled to either  
a refund or replacement of the product or its component part or parts. Replacement of a component  
part includes its free installation, except as specified under the limited warranty. Under the terms of this  
warranty, service must be performed by a factory authorized Viking Range, LLC service agent or  
representative. Service will be provided during normal business hours, and labor performed at overtime  
or premium rates shall not be covered by this warranty.  
Owner shall be responsible for proper installation, providing reasonable and necessary maintenance,  
providing proof of purchase upon request, and making the appliance reasonably accessible for service.  
The return of the Owner Registration Card is not a condition of warranty coverage. You should, however,  
return the Owner Registration Card so that Viking Range, LLC can contact you should any question of  
safety arise which could affect you.  
This warranty gives you specific legal rights, and you may also have other rights which may vary from  
jurisdiction to jurisdiction.  
WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from  
abuse, failure to provide reasonable and necessary maintenance, accident, delivery, negligence, natural  
disaster, loss of electrical power to the product for any reason, alteration, outdoor use, improper  
installation, improper operation, or repair or service of the product by anyone other than an authorized  
Viking Range, LLC service agency or representative. This warranty does not apply to commercial usage.  
22  
23  
 

Tascam Stereo Receiver US 2x2 User Manual
Teledyne TV Converter Box pjnmoo385 User Manual
Telex Power Supply MS 2002 User Manual
Thermador Cooktop CVS30R 36 User Manual
Tokina Camera Accessories TM10Z0818GAI User Manual
Toshiba Printer Black White MFP User Manual
Troy Bilt Tiller 640C User Manual
Troy Bilt Tiller 12001 User Manual
Vizio Blu ray Player VBR333 User Manual
Vulcan Hart Indoor Furnishings Wallmnt Chrbkr User Manual