Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
Built-In Electric Induction Cooktop
F20112E EN
(022108J)
PROXIMITY TO SIDE CABINET INSTALLATION
1. The cooktop may be installed directly to existing base cabinets.
INTERIOR CABINET CLEARANCES
2. The cooktop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36” (91.4 cm) high. There must be a minimum of 6” (15.2 cm) side clearance from the cooktop to
such combustible surfaces above the 36” (91.4 cm).
3. Within the 6” (15.2 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm), the maximum wall cabi-
net depth must be 13” (33.0 cm) and wall cabinets within this 6” (15.2 cm) side clearance must be 18” (45.7 cm)
above the 36” (91.4 cm) high countertop.
IMPORTANT: The electronic components for the in-
duction elements in the cooktop need some air circula-
tion. To ensure long life of electronic components, it is
required that a minimum of 8” (20.3 cm) open space re-
main between the bottom of the cooktop and any shelf
underneath. The maximum length of the shelf under-
neath is 18” (45.7cm). There should be no partition or
shelf directly underneath the unit.
1 1/4”
(3.2 cm)
min.
8”
(20.3 cm)
min.
4. Wall cabinet above the cooktop must be a minimum of 36” (91.4 cm) above the countertop for a full width of the
cooktop.
It is also required that the exit air ports at the rear are
not blocked. There should be a minimum of 1 1/4” (3.2
cm) space between the exit air ports at the rear of the
unit and any nearby obstruction including downdrafts.
18”
(45.7 cm)
max.
13” Max
(33.0 cm)
36” Min.
(91.4 cm)
18” Min.
(45.7 cm)
0” Min.*
(0 cm)
36” Min.
(91.4 cm)
3 1/8”
(7.9 cm)
MINIMUM CLEARANCES FROM ADJACENT COMBUSTIBLE
CONSTRUCTION
•Above countertop (above 36” [91.4 cm])
•Side 6” (15.2 cm)
•Rear* 0” (0 cm)
•Within 6” side clearance. Wall cabinets no deeper
than 13” (33.0 cm)
•Must be minimum 18” (45.7 cm) above countertop
•Wall cabinets directly above the product must be
minimum 36” (91.4 cm) above the countertop.
*NOTE: Before cutting countertop cutout, check the inside
clearance available from the inside back wall to the proposed
placement of the cooktop. A minimum of 1 1/4” (3.2 cm) is re-
quired from the back wall of the cooktop to the inside wall of
the back cabinet. (See page 5) This may require a distance
greater than the 0” minimum approved distance.
5
4
DIMENSIONS
INDUCTION/RADIANT COOK-
TOP
36” W. TOP
30” W. TOP
21”
(53.3 cm)
21”
(53.3 cm)
36 3/4” (93.3 cm)
30 3/4” (78.1 cm)
#1
36” W. BURNER
BOX
#2
30” W. BURNER BOX
18 31/32”
(48.2 cm)
#1
#2
18 3/8”
(46.7 cm)
#1
#2
34 1/2” (87.6 cm)
30” W. HEIGHT
There are two types of hold down brackets on the 36” w. cooktop. After in-
stalling cooktop, locate the hold down brackets around the burner box. Brack-
ets #1 are located on the left side of the burner box and brackets #2 are located
on the right side of the burner box. Screw the sheet metal screw into the
brackets and tighten firmly against bottom of countertop.
#2
#1
6 11/16”
(17.0 cm)
5 1/4”
(13.3 cm)
4 1/2”
(11.4 cm)
6 7/16”
(16.4 cm)
36” W. HEIGHT
After installation of cooktop, locate the four hold down brackets on each
side of the burner box. Screw the sheet metal screw into bracket and
tighten firmly against bottom of countertop.
3 1/16”
(7.8 cm)
6 11/16”
(17.0 cm)
5 7/32”
(13.3 cm)
4 15/32”
(11.4 cm)
2 5/16” (5.9 cm)
7
6
DIMENSIONS
ALL INDUCTION COOKTOP
36” W. TOP
36 3/4” (93.3 cm)
30 3/4” (78.1 cm)
30” W. TOP
21”
(53.3 cm)
21”
(53.3 cm)
36” W. BURNER BOX
30” W. BURNER BOX
18 3/4” (47.6 cm)
18 3/4”
(47.6 cm)
36” W. HEIGHT
30” W. HEIGHT
7 1/2”
(19.1 cm)
4 1/32”
(10.2 cm)
5 3/16”
(13.2 cm)
7 1/2”
(19.1 cm)
4 1/16”
(10.3 cm)
5 1/8”
(13.0 cm)
28 1/2” (72.4 cm)
After installation of cooktop, locate the four hold down brackets on each
side of the burner box. Screw the sheet metal screw into bracket and
tighten firmly against bottom of countertop.
After installation of cooktop, locate the four hold down brackets on each
side of the burner box. Screw the sheet metal screw into bracket and
tighten firmly against bottom of countertop.
9
8
30” W. CUTOUT
36” W. CUTOUT
Min. 19 1/8” (48.6 cm)
Max. 19 7/8” (50.5 cm)
Min. 19 1/8” (48.6 cm)
Max. 19 7/8” (50.5 cm)
Min. 34 9/16” (87.8 cm)
Max. 35 1/2” (90.2 cm)
Min. 28 9/16” (72.6 cm)
Max. 29 5/8” (75.2 cm)
7/8”
7/8”
(2.2 cm)
33” (83.8 cm)
36” W. CUTOUT w/
DOWNDRAFT
7/8”
(2.2 cm)
(2.2 cm)
2 1/4”
(5.7 cm)
7/8”
(2.2 cm)
27” (68.6 cm)
30” W. CUTOUT w/
DOWNDRAFT
2 1/4”
(5.7 cm)
20 1/4”
(51.4 cm)
20 1/4”
(51.4 cm)
34 3/4” (88.3 cm)
28 3/4” (73.0 cm)
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off.
2. All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this mate-
rial. If buildup occurs, do not use steel wool, abrasive cloths, cleaners, or powders! If it is necessary to scrape stain-
less steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wood or nylon
scraper. Do not use a metal knife, spatula, or any other metal tool to scrape stainless steel! Scratches are almost im-
possible to remove.
REPLACEMENT PARTS
Only authorized replacement parts may be used in performing service on the cooktop. Do not repair or replace any part
of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified
technician.
11
10
|