Installation Check List
Mount the compressor as shown, with both feet
either underneath or on the side. The mounting plate
should be flat and strong enough to support 120 lbs.
For air circulation, there must be an 8" x 8” hole in
the center of the mounting plate or 1” spacer blocks
under the mounting feet.
J150 COMPRESSOR
Installation and Operation
Manual
The long capscrews (35mm) should be used on the
feet. Tighten to 26 ft. lbs.
Rotation of the machine is shown by the arrow on
the body between the suction and delivery port.
- Arrow points to suction port. -
Mount the machine so that the rotation matches the
PTO rotation. To change rotation, remove cowls,
switch drive flange/yoke to other end of compressor,
and replace the cowls.
Truck frame
rail
Inlet Air Filter
# 713000205
Do not force end yokes or drive flange onto the
compressor or PTO shaft.
Use a tube type balanced PTO drive shaft, parallel
with the PTO output shaft axis within 2° to ensure
vibration-free running. The maximum driveline angle
is 10°.
A 30 or 36psi relief valve should be mounted 12”-24”
from the compressor discharge with valve outlet
away from machine and filter inlet.
12” Min or as
req to clear
1-1/2”
Pipe Typ
The air filter should be mounted in an upright
position at least 12” from compressor inlet, with free
access to element and away from exhaust fumes
and road spray. For tractor mount, we recommend
above frame rails behind the cab.
Suction (1½” I.D.) and delivery pipework (1½” I.D.,
1” I.D. minimum) should be free of weld beads or
foreign material and supported by brackets. Do not
contaminate the inside of the piping with Teflon tape
or pipe dope thread sealer.
If pipework runs to the opposite frame rail, it must
have a flexible section to prevent distortion of the
compressor.
Install discharge filter (p/n 713031200, M202 or
equivalent) with minimal restriction, to prevent
compressor overheating.
Mtg Brkt (optional )
(2) pc # 712000202
Typical Inlet Pipe Work
Arrangement - Side Mount Ports
Chicago Fitt
# 531296200
3-Way Ball Valve
# 705011205
Check Valve
# 705012205
A 3-way ball valve (1”) should be installed into
delivery pipework to bleed air and control system
pressure. The ball valve should be installed prior to
Chicago fitting to manually isolate the compressor
from the trailer.
A liquid-filled pressure gauge is recommended in the
delivery pipework for ease of operation and system
troubleshooting.
The operating speeds are:
• 1000 -1800rpm for J150
• For optimum performance 1200-1400rpm is
recommended.
Relief Valve
# 705011205 - 30 psi
Option - 36 psi
# 705000216
12” Min
Calculate engine speed using the PTO ratio.
A constant speed governor or throttle control system
is recommended.
Check compressor speed with tachometer to ensure
proper operation.
Post engine speed in cab on label provided.
Typical Outlet Pipe Work
Arrangement - Side Mount Ports
Important Notes
Operation
• These instructions are not intended to modify or circumvent
any company policies or procedures. Any differences, whether
stated or implied should be investigated before proceeding.
• Never pour any liquid or rust inhibitor in the machine, as it will
damage the blades.
• Inspect compressor mounting, driveline, PTO, and air filter for
integrity.
• Check that the bleed valve is set to vent to atmosphere.
• Follow trailer instructions regarding product hose connection
and valve operation.
• Slowly engage PTO with engine at idle, and bring up to
operating speed shown on label.
Routine Maintenance
Incorrect speed will cause compressor failure.
• Lock engine at recommended speed. The engine speed
must remain constant throughout the discharge cycle.
• Turn bleed valve to direct air into the tank.
• Unload trailer as per trailer manufacturer’s recommendation.
Do not exceed maximum tank pressure.
Weekly
- Check driveline stability.
- Mounting integrity of compressor and pipework.
- Clear fan area and body of any obstructions.
- Run machine for 2-3 minutes.
• If relief valve is operating, adjust bleed valve to reduce tank
pressure.
Monthly
- Air filter element is clean.
- PTO mounting bolts and transmission oil level.
- Drive shaft bearings.
Note: Do not decrease engine speed to reduce pressure.
Too low (or high) speed will cause compressor failure.
- Compressor and pipework installation bolts.
- Check valve is functioning.
- Relief valve setting, 30psi for J150 ( optional 36 psi )
- Check compressor speed is maintained by governor
- No air leaks.
• When unloading is completed, open the bleed valve and
reduce pressure as per trailer manufacturer’s instructions.
• Check that all valves are in their correct shutdown positions.
• Disengage PTO.
- Is engine speed label visible in cab?
Hydraulic Drive Operation
Yearly
- Check blade wear by measuring distance from the corner of
the rotor slot to the blade. Replace blade before
5/8” wear is reached.
Blade wear can be checked through the
suction port with calipers,after machine is turned off and cool.
• Engage PTO and set correct engine speed.
• Operate the selector valve to start the compressor.
• Continue as PTO drive, use the selector valve to stop the
compressor when unloading is complete.
New Blade
Note -
Failure to replace the
Worn Blade
A = 5/8”
blades will eventually
result in machine failure.
Late blade change can
permanently damage the
machine so that future
blade life is reduced.
Blade Replacement Fig 4
Bill of Material
Detail
Qty
Part No.
Description
1
2
3
4
5
6
7
8
1
1
2
2
1
1
2
6
8
2
1
2
2
2
2
4
1
A/R
2
2
6
8
8
1
1
1
1
2
1
2
2
2
2
2
6
500000200
Compressor Body
Rotor
Side Plate
3664516000-2
3801816005-2
3301016450-2
505020200
Fan
Cowl Non Drive End
Cowl Drive end
O-ring - 147
505010200
6758300600-2
3091616000-2
3131216848-2
M750280015-7
M200807040-4
7701100635-2
7711100635-2
7721100635-2
7731100635-2
7200300470-2
6726200451-2
520010203
6950900841-2
174210040
128110425
7360100000-2
128110435
V200-F30
6710300451-2
6726500451-2
6726600451-2
6036900850-2
302127203
3730700869-2
M140620000-8
7163500000-2
7163600000-2
3150116
Blade - V1754
9
Bushing - Mounting
Star Tolerance Ring
Key
Shim - 0.050
Shim - 0.075
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
30
31
32
33
34
35
36
37
38
39
40
Shim - 0.125
Shim - 0.250
Sealong Disc ( Lead Plug )
Drum Name plate
Grease ( Areoshell # 5 )
AVSEAL Plug
Shoulder Screw
Cap Screw M10 x 25 mm
Metal Tack
Cap Screw M10 x 35 mm
Relief Valve - 30 psi
Rotation Arrow Label
Air Inlet Name Plate
Discharge Name Plate
Bearing NJ306
35 mm Plug
Air Seal 48 mm x 62 mm x 7 mm
Snap Ring 62 mm
Oil Seal double lip
Oil Seal double lip
Bearing Housing Cap
Cap Screw M10 x 20 mm
128110020
SAFETY
PRECAUTIONS
• Rotating shafts can be dangerous. You can snag clothes, skin, hair, hands, etc. This can
cause serious injury or death.
• Do not work under the vehicle when the engine is running.
• Do not work on a shaft (with or without a guard) when the engine is running.
• Do not engage or disengage driven equipment by hand from under the vehicle when the
engine is running.
• In order to avoid becoming entangled, install the power takeoff and/or shaft behind the frame
rail, tanks, battery box, etc.
• If power takeoff and/or shaft are still exposed after installation, install a guard.
• Install a support strap when servicing a driveshaft to prevent personal injury.
• Compressor housing & associated piping or accessories may become hot enough to
cause burns on contact.
• Wear adequate ear protection and avoid extended exposure in close proximity to noisy
machinery.
• A serious or fatal injury can occur . . .
if you lack proper training
if you fail to follow proper procedures
if you do not use proper tools and safety equipment
if you assemble driveline components improperly
if you use incompatible driveline components
if you use worn-out or damaged driveline components
if you use driveline components in a non-approved application.
• These instructions contain safety instructions. Read, understand and follow these instructions.
Get proper training
Learn and follow safe operating procedures
Use proper tools and safety equipment
Use proper components in good condition
WARRANTY
WARRANTY: The Seller warrants the goods sold hereunder against defects in workmanship or materials under normal and proper installa-
tion for a period of twelve (12) months from the date of delivery. BUYER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY IS
FOR THE REPAIR OR REPLACEMENT AT SELLER’S OPTION, WITHOUT CHARGE TO BUYER EXCEPT FOR SHIPPING EXPENSES, AT THE
OFFICE OF THE SELLER IN LOUISVILLE, KENTUCKY, OF ANY PART WHICH HAS PROVEN TO BE DEFECTIVE AT THE TIME IT WAS
DELIVERED. ANY GOODS UNDER WARRANTY MUST BE RETURNED TO THE SELLER’S OFFICE FOR INSPECTION BY THE SELLER AND, IF
ANY SUCH GOODS ARE FOUND TO BE DEFECTIVE, FOR REPAIR OR REPLACEMENT. ALL FREIGHT AND EXPENSES OF SHIPMENT TO
AND FROM THE SELLER’S OFFICE SHALL BE BORNE BY THE BUYER. THE SELLER IS NOT RESPONSIBLE FOR ANY EXPENSES OF ANY
NATURE INCURRED FOR ANY REPAIRS TO ALTERATIONS MADE BY OTHERS TO THE GOODS OR ANY OTHER EQUIPMENT WITHOUT
THE PREVIOUS WRITTEN CONSENT OF THE SELLER. SHOULD THE GOODS BE PARTIALLY OR FULLY INSTALLED, ALTERED, STRIPPED,
REPAIRED, SERVICED, OR MAINTAINED BY ANY PERSON OTHER THAN AUTHORIZED AGENTS AND EMPLOYEES OF THE SELLER,
WITHOUT THE PREVIOUS CONSENT OF THE SELLER, OR MISUSED IN ANY WAY, THIS WARRANTY SHALL BE VOID. THIS WARRANTY
CONSTITUTES THE ONLY WARRANTY BY THE SELLER OF THE GOODS AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR WARRANTIES OF FITNESS FOR A PARTICULAR
PURPOSE. IN NO EVENT SHALL SELLER BE LIABLE FOR BUYER’S ATTORNEY’S FEES.
NO CONSEQUENTIAL DAMAGES: UNDER NO CIRCUMSTANCES SHALL THE SELLER BE LIABLE FOR (A) FOR ANY CONSEQUENTIAL,
SPECIAL, OR CONTINGENT DAMAGES OR EXPENSES, OR ANY OTHER CHARGES BEYOND THE INVOICE VALUE OF THE DEFECTIVE
ITEMS, (B) ANY DAMAGE, INJURY, BREAKAGE OR LOSS OF ANY KIND WHATSOEVER, (C) ANY LOSS OF INCOME, OR (D) ANY CONSE-
QUENTIAL LOSS.
NO TORT LIABILITY: SELLER DISCLAIMS ANY LIABILITY FOR CLAIMS BASED ON SELLER’S NEGLIGENCE OR STRICT LIABILITY IN TORT.
PARTS: This Warranty and all disclaimers and limitations of liability shall apply to all parts sold to Buyer.
TRAINING AND SUPERVISION: The buyer hereby assumes the affirmative duty to properly educate, instruct and supervise its employees
and all others, except employees of the Seller, in the safe, proper use and operation of the goods. The Buyer agrees to indemnify the
Seller for any damages paid by the latter as a result of the Buyer’s failure to perform this affirmative duty.
Seller is not responsible for claims for damage due to improper installation or maintenance, corrosive fluids, or use of a product for a
purpose other than it was specifically designed for. The goods are not designed or intended for use with every substance. If the material
which the Buyer contemplates transferring with the goods has corrosive or polymerizing or other properties which may result in unsatisfac-
tory or dangerous operations, the Seller has no liability or responsibility for performance of the goods.
RETURN OF GOODS: No goods supplied may be returned to the Seller for credit without the Seller’s prior written authorization before
transportation thereof commences and in such cases transportation must be prepaid and the Buyer’s name, address, original order number
and the Seller’s invoice number must be clearly marked on the shipping tag.
If any goods are returned to the Seller for repair or under warranty and no instructions are received within two months after Seller receives
the goods for repair or sends notice to Buyer of the disallowance of a warranty claim, the Seller reserves the right to scrap the goods
returned, and no subsequent claim for any costs or losses will be accepted.
APPLICABLE LAW AND VENUE: The rights and obligations of the parties hereunder shall be governed in all respects, including all ques-
tions of construction and performance of this order, by the laws of Kentucky. All disputes concerning this order shall be resolved in an
appropriate state or federal court located in Louisville, Kentucky.
MODIFICATION OR RESCISSION: This warranty can only be modified or rescinded by a written agreement signed by an officer of both the
Buyer and the Seller.
Syltone Industries, LLC
Louisville, Kentucky
SYLTONE INDUSTRIES, LLC
2501 Constant Comment Place
Louisville, KY 40299
phone: 800-626-6334
phone: 502-266-6677
fax:
502-266-5873
e-mail: [email protected]
date: 3-13-03 BKR First Issue
|