IMPORTANT!
READ AND SAVE THESE INSTRUCTIONS
®
Vicks Natural Mist Humidifier
(Model V3500)
Use and Care Manual
If you have any questions about the operation of your Vicks Natural Mist Humidifier, call our
toll-free Consumer Service line at 800 477-0457
k
Manufacturing Quality Healthcare Products for Over 75 Years
®
Important Safety Instructions
Vicks Natural Mist Humidifier
READ ALL INSTRUCTIONS BEFORE
USING HUMIDIFIER, ESPECIALLY THESE
BASIC SAFETY PRECAUTIONS:
1. Always place Humidifier on a firm, flat, level surface, at least FIVE inches away from
walls and heat sources such as stoves, radiators or heaters. Humidifier may not work
properly on a non-level surface.
Tank Handle
Water Tank
2. When moving, or lifting the Humidifier make sure you have a secure grip under the
Base of unit. When removing the Tank, use one hand on the Tank Handle and the other
on the bottom of the Tank on the Fill Cap. This will help prevent leakage of water or
breakage of the unit itself.
Fan Housing
3. Place Humidifier in an area that is out of the reach of children.
4. Before using the Humidifier, extend the cord and inspect for any signs of damage.
Do not use the product if cord has been damaged.
Switch Knob
5. This product has a polarized plug (one blade is wider than the other) as a safety feature.
This plug will fit into a polarized outlet only one way. If the plug does not fit fully into
the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safety feature.
Speed Selector
Cap Gasket
(Black O-Ring)
WF2
Wicking Filter
6. Humidifier should always be unplugged and emptied when not in operation or while
being cleaned.
7. Never tilt or move the Humidifier while it is in operation. Shut off and unplug before
moving.
Fill Cap
8. Humidifier requires regular cleaning. Refer to and follow cleaning instructions.
Base
SAVE THESE INSTRUCTIONS
®
Using Your Vicks Natural Mist Humidifier
Care and Cleaning
Your Vicks Humidifier comes fully assembled and ready to use.
CAUTION: ALWAYS TURN OFF THE POWER SWITCH AND DISCONNECT THE POWER
CORD FROM THE ELECTRICAL OUTLET BEFORE CLEANING.
Humidifiers provide comfort by adding moisture to dry indoor air. For maximized benefit from
your Vicks Natural Mist Humidifier, follow instructions carefully. Please note that this is an
electric appliance and requires careful attention when in use.
First Time Use
Read all instructions before using this appliance.
Filling the Humidifier
Tap water may contain pollutants and minerals (scale) that can deposit on the inner surfaces
of the Humidifier and clog the Wicking Filter. Such scale can accelerate the growth of
microorganisms and can impair the performance of the Filter.
1. Unpack Humidifier. Remove Fan Housing and check that the Wicking Filter is in place
in Base. Replace Fan Housing, being careful to seat it properly onto the Base.
2. Place Humidifier at least FIVE inches away from walls and heat sources, on a FIRM,
FLAT, LEVEL surface. Place on a water-resistant, non-conducting surface for protection
from inadvertent spillage. Do not place any object over the Humidifier; it could block
air openings.
Daily Maintenance
1. Turn switch to off (O) position and unplug the cord from wall outlet.
2. Remove Tank & Fan Housing and empty Base. Rinse Base and Tank, wipe clean, and dry
with a clean cloth or paper towel. Be careful that you do not damage the delicate Wicking
Filter. DO NOT immerse the Fan Housing or clean with water.
3. Completely unravel power cord. Inspect power cord for signs of damage before use.
If cord is damaged, DO NOT use product, please call 1-800-477-0457.
3. Replace Fan Housing then the Tank. Humidifier is now ready for use.
Weekly Maintenance—Removing Scale
4. Keep cord away from heated surfaces and out of the way, where it cannot be stepped
on or tripped over.
5. Remove Tank using Tank Handle. Turn Tank over and carefully remove Fill Cap by turning
Fill Cap counter clockwise. Fill the Tank with cool tap water. WARNING: Never use
hot water - may cause damage to Wicking Filter.
1. Empty any remaining water from the Base and Tank. Reassemble Humidifier.
2. Turn switch on and operate the Humidifier without water until the Wicking Filter is
thoroughly dry.
6. Make sure the circular rubber Cap Gasket (O-Ring) is in place before replacing Fill Cap
3. Turn switch to the OFF (O) position and unplug the cord from wall outlet.
on Tank (this prevents water leakage). To tighten, turn Fill Cap clockwise.
4. Remove Tank & Fan Housing and place on a flat surface. Remove the Wicking Filter from
7. When carrying Tank always use two hands (one on Handle, one on the Fill Cap). Insert
the Base by carefully lifting straight up, without bending or breaking or tearing the Filter.
Tank back into Base.
5. Fill Base with undiluted white vinegar. Let solution stand for 20 minutes.
6. Dampen soft, clean cloth or sponge with undiluted white vinegar and wipe out Base
to remove scale. DO NOT use soap, detergents or abrasive cleaners.
Operating Instructions
1. Fill the Water Tank and replace Tank on Base.
7. Rinse thoroughly in clean warm water to remove scale and vinegar before disinfecting
the Base.
2. Make sure that switch is in OFF (O) position, place the unit on a flat, stable surface and
Disinfecting Base
plug cord into a 120 VAC wall outlet.
1. Fill Base with 1 teaspoon of household bleach in 1 gallon of water. Let solution remain
CAUTION: DO NOT PLUG IN THE CORD WITH WET HANDS; ELECTRIC
SHOCK COULD RESULT.
for 20 minutes, stirring every few minutes to ensure that all surfaces are coated.
2. Empty Base after 20 minutes. Rinse with water until bleach smell is gone. Dry with clean
3. Turn switch to either High or Low. Fan will start turning.
cloth or paper towel.
3. Wipe all exterior surfaces of the Fan Housing with a soft, dry cloth.
DO NOT USE WATER TO CLEAN THE FAN HOUSING. AN ELECTRIC SHOCK
MAY RESULT OR THE HUMIDIFIER MAY BE DAMAGED. DO NOT IMMERSE
OR SPRAY ANY PART OF THE HUMIDIFIER WITH WATER.
4. Replace the Wicking Filter into the Base, being careful not to damage the Filter.
NOTE: Do not wash the Wicking Filter, since this will damage the Wicking Filter.
Wicking Filter Maintenance
Wicking Filter performance will diminish depending on the mineral content of the
water and the amount of airborne dust in the environment.
End of Season Maintenance or When
Humidifier Will Not Be In Use For
At Least One Week
IMPORTANT: CHECK WICKING FILTER REGULARLY. Any of the following conditions indicate
1. Clean and dry the Humidifier thoroughly as per the Weekly Maintenance instructions above.
2. Let Humidifier dry completely before storing. Do not store with water inside the Base.
3. Remove Fill Cap. Do not store Humidifier with Fill Cap on.
that it is time to replace the Wicking Filter.
•
A buildup of impurities and minerals on the Wicking Filter (evidenced by discoloration of
the Wicking Filter)
•
•
•
An appreciable decrease in Humidifier output
The top of the Wicking Filter is not moist to the touch
The Wicking Filter has large holes or tears
4. At end of season, remove and throw away the Wicking Filter. Never leave a used Wicking
Filter in the Humidifier during storage.
5. Store in a cool dry location.
6. Order your new Kaz Replacement Wicking Filter now, so that it will be available for use
The Wicking Filter should be replaced at least one or two times during the season, depending
on usage, mineral content of the water and the environment. We encourage you to only use a
Kaz Model WF2 Replacement Wicking Filter. The use of other Wicking Filters may lead to
substandard performance.
next season.
Trouble-Shooting
If the unit does not operate:
Replacement Filters
WF2 Wicking Filters are generally available where you purchased your Humidifier. If you are
unable to locate replacement filters at your local retailer, they may be ordered directly from Kaz.
•
•
•
Check that polarized plug is fully inserted into wall outlet.
Check airflow. Are there any obstructions preventing airflow?
WF2 Wicking Filters cost $10 for 2 Filters or $7 for 1 Filter plus $4 for
handling and postage.
The motor contains a temperature-limiting fuse. If the motor overheats, the fuse will trip
and shut off the motor. Unplug the unit and contact our Consumer Service Department.
Do not attempt to repair the motor yourself.
NOTE: Prices are subject to change without notice.
If you do not obtain enough humidity:
To Order:
•
The moisture output from an evaporative Humidifier is invisible. It is operating properly
if water level goes down during usage, even when you cannot see the vapor.
By Phone
•
•
Check the Wicking Filter. Replace the Filter if it is clogged, torn or discolored.
Call toll-free by dialing 1-800-477-0457. Please have your credit card handy for payment. We
accept Visa and Master Card. Minimum credit card order is $10.00.
Check the water level. Refilling may be required.
If you are obtaining too much humidity:
By Fax
•
If room air is excessively humid (greater than 50% relative humidity), do not use the
Humidifier. Excessive humidity is indicated by condensation on cold surfaces or walls in
the room. For proper humidity readings, use a hygrometer available in most hardware
and department stores.
Fax your order to Kaz Consumer Service Orders at 1-518-828-2015. Please clearly print your
name, mailing address and products ordered. Be sure to specify Visa or Master Card, card
number and expiration date, and sign your order. Minimum credit card order is $10.00.
By Mail
If water leakage occurs:
Mail your order to Kaz Consumer Service Orders, One Vapor Trail, Hudson, NY 12534. Please
clearly print your name, mailing address, and products ordered. Enclose check or money order
(no cash, please).
•
•
Make sure unit is unplugged from wall outlet.
Remove Tank from Base and check Fill Cap. Make sure the Cap Gasket (O-Ring) is
properly positioned in the cap and the spring valve operates freely. If leakage still
occurs contact our Consumer Service Department.
Via The Internet
E-mail us at consumerservice@kaz.com. Be sure to include your name, mailing address and
products ordered. Please specify Visa or Master Card, card number and expiration date.
Minimum credit card order is $10.00.
If Fill Cap is too tight:
Lightly lubricate the Cap Gasket (O-Ring) with petroleum jelly.
•
|