VX-10
Owner's Manual
Audio/VideoSubwoofer
WICHTIGE SICHERHEITSHINWEISE
VORSICHT
GEFÄHRLICHE SPANNUNG
NICHT ÖFFNEN
Vorsicht: Zur Vermeidung von Gefahr durch elektrischen Schlag, Deckel (oder Rückwand) nicht
abnehmen. Produkt enthält keine Anwenderteile. Reparatur und Wartung nur von qualifiziertem
Fachpersonal vornehmen lassen.
Das Blitzsymbol dient als Hinweis auf unisolierte „gefährliche Spannungen“ innerhalb des Gehäuses,
deren Werte eine Berührungsgefahr für den Menschen darstellen können.
Das Symbol mit dem Ausrufungszeichen dient als Hinweis auf wichtige, in den Unterlagen des
Subwoofers enthaltene Bedienungs- und Wartungsvorschriften.
1.
Anleitungenlesen-AlleSicherheits-undBedienungsanleitungenvorInbetriebnahmedesSubwoofersaufmerksam
durchlesen.
2.
3.
4.
5.
Anleitungenaufbewahren-DieSicherheits-undBedienungsanleitungenzurspäterenBezugnahmeaufbewahren.
Warnungen beachten - Alle Warnungen am Subwoofer und in der Bedienungsanleitung unbedingt beachten.
Anleitungen befolgen - Alle Bedienungs- und Gebrauchsanleitungen genau befolgen.
Wasser und Feuchtigkeit - Subwoofer nicht in der Nähe von Wasser aufstellen, d.h. neben einer Badewanne,
Spüle, Waschmaschine, in einem feuchten Keller, in der Nähe des Swimmingpools o.ä..
Rollwagen und Ständer - Subwoofer nur mit einem vom Hersteller empfohlenen Rollwagen oder Ständer
benutzen.
Wand-oderDeckenbefestigung-SubwoofernurdenHerstellerempfehlungengemäßanderWandoderDecke
befestigen.
Belüftung - Subwoofer so aufstellen, daß die erforderliche Belüftung nicht behindert wird. D.h., Subwoofer
nicht auf einer weichen Oberfläche wie einem Bett, Sofa,Teppich o.ä.aufstellen, die die Belüftungsöffnungen
blockieren kann. Subwoofer gleichfalls nicht in einem Regal oder Schrank unterbringen, worin die Luftzufuhr
behindert wird.
6.
7.
8.
9.
Wärme - Subwoofer nicht in der Nähe von Wärmequellen, wie Heizkörpern, Wärmespeichern, Öfen oder
anderen wärmeerzeugenden Subwoofern aufstellen.
10. Netzanschluß-SubwoofernuraneinederinderBedienungsanleitungbeschriebenenoderaufdemSubwoofer
angegebenen Stromquellen anschließen.
11. Netzkabelschutz - Netzkabel so verlegen, daß nicht daraufgetreten wird oder sie durch darauf-oder
dagegengestellte Gegenstände eingeklemmt werden können. Die Anschlußstellen des Netzkabels an
Steckdosen und am Subwoofer dabei besonders beachten.
12. "Vorsicht": ZurVermeidung von Gefahr durch elektrischen Schlag sicherstellen, daß der Schutzkontakt
des Steckers vollständig in die Steckdose eingeführt ist.
13. Reinigung - Subwoofer nur den Herstellerempfehlungen gemäß reinigen.
14. Betriebsfreie Zeiträume - Netzkabel des Subwoofers aus der Steckdose ziehen, wenn er über einen längeren
Zeitraum nicht benutzt wird.
15. Beschädigungen durch Gegenstände oder Flüssigkeiten - Es ist darauf zu achten, daß keine Gegenstände
auf das Gehäuse fallen oder Flüssigkeiten darauf verschüttet werden.
16. Beschädigungen, die eine Reparatur erforderlich machen - Subwoofer sollte von qualifiziertem Fachpersonal
repariert werden, wenn:
a.
b.
c.
d.
e.
Das Netzkabel oder der Stecker beschädigt sind.
Gegenstände oder Flüssigkeiten in den Subwoofer gelangt sind.
Der Subwoofer dem Regen ausgesetzt wurde.
Der Betrieb des Subwoofers gestört ist oder seine Leistung deutlich nachgelassen hat.
Der Subwoofer fallengelassen oder beschädigt wurde.
17. Reparatur und Wartung - Durch den Benutzer auszuführende Wartungsmaßnahmen des Subwoofers sind auf
die in der Bedienungsanleitung angegebenen Prozeduren beschränkt.
18. Überlastung - Zur Vermeidung von Brandgefahr und elektrischem Schlag Wandsteckdosen,
Verlängerungskabel bzw. eingebaute Steckdosen nicht überlasten.
19. Ersatzteile - Wenn Ersatzteile benötigt werden, sicherstellen, daß der Servicetechniker entweder die
vom Hersteller angegebenen Ersatzteile benutzt oder Teile, die den Originalteilen entsprechende
Kennwerte besitzen. Die Verwendung von Ersatzteilen, die nicht zugelassen sind, kann Brände,
elektrischen Schlag oder andere Gefahren verursachen.
20. Sicherheitsprüfung - Nach Beendigung von Wartungs- oder Reparaturmaßnahmen an diesem Produkt
☞
2
IMPORTANTES CONSIGNES DE SECURITE
ATTENTION
Risque d’électrocution
Ne pas ouvrir
Attention: Afin d’éviter tout risque d’électrocution, ne pas enlever le boitier (ou partie
arrière de l’enceinte). Aucune pièce ne doit être manipulée par l’utilisateur. Pour tout
entretien, vous référer à un
personnel de service qualifié.
Le symbol de l’éclair avec la flèche sert à avertir l’utilisateur de la présence d’un “voltage
dangereux” non isolé dans l’enceinte du produit d’une magnitude pouvant constituer un
risque d’électrocution de personnes.
Le symbol du point d’exclamation sert à avertir l’utilisateur que d’importants conseils de
fonctionnement et de maintenance (entretien) sont fournis avec l’enceinte d’extrêmes
graves.
1.
2.
3.
4.
5.
Lire le mode d’emploi - Tous les conseils de sécurité et de fonctionnement doivent être lus avant
de mettre en marche l’enceinte.
Garder le mode d’emploi - Il est conseillé de conserver les conseils de sécurité et de fonctionnement
pour un éventuel usage futur.
Avertissements - Il est important de se conformer à tous les conseils de fonctionnement concernant
l’enceinte et à toutes les instructions inscrites sur l’enceinte.
Suivre les conseils - Tous les conseils d’utilisation et de fonctionnement doivent être suivis à la
règle.
Eau et humidité - Ne pas utiliser l’enceinte près d’une source d’eau - par exemple, près de la
baignoire, d’une bassine de lavage, d’un évier de cuisine, d’un bac à lavage, dans un sous-seul
mouillé, près d’une piscine…
6.
7.
Pieds et Supports - N’utiliser que des pieds et supports recommandés par le fabricant.
Assemblage mural ou au plafond - Se conformer uniquement aux instructions du fabricant pour fixer
l’enceinte sur un mur ou sur un plafond.
8.
Ventilation - Il est important de placer l’enceinte de telle sorte qu’elle ne gêne pas sa propre
ventilation. Par exemple, ne pas placer l’enceinte sur un lit, un canapé, sur la moquette, ou sur
toute surface similaire qui bloque les ouvertures de ventilation ; ne pas poser l’enceinte dans une
meuble encastré ou fermé telle qu’une bibliothèque ou un meuble qui empêche l’air de circuler par
les ouvertures de ventilation de l’enceinte.
9.
Chaleur - Placer l’enceinte loin de toute source de chaleur tels que radiateurs, compteurs thermiques,
fours ou autres enceintes dégageant de la chaleur.
10. Sources d’électricité - Ne brancher l’enceinte que dans une prise du type décrit dans le mode
d’emploi ou comme indiqué par le fabricant.
11. Protection du cordon électrique - Les cordons électriques doivent être fixés pour éviter que toute
personne ne marche dessus et que rien ne puisse être placé sur ou contre eux - faire tout
particulièrement attention aux cordons branchés dans des prises électriques, à des réceptacles et
à leurs points de sorties de l’enceinte.
12. ”Attention : Afin d’éviter tout choc électrique, introduire la lame la plus large de la fiche dans la
borne correspondante de la prise et pousser jusqu’au fond”.
13. Nettoyage - Pour le nettoyage de l’enceinte, suivre scrupuleusement les instructions du fabricant.
14. Périodes de non-utilisation - Le cordon électrique de l’enceinte doit rester débranché si l’enceinte
reste inutilisée pendant une longue période de temps.
15. Infiltration d’objet ou de liquide - Faire attention à ce qu’aucun objet ne tombe et à ce qu’aucun
liquide ne soit versé sur l’enceinte.
16. Dommages nécessitant réparation - L’enceinte ne doit être réparée que par du personnel qualifié
lorsque :
a.
b.
c.
d.
e.
le cordon électrique ou la prise ont été endommagés.
Des objets sont tombés ou du liquide a été versé sur l’enceinte.
L’enceinte a été exposée à la pluie.
L’enceinte ne semble pas fonctionner normalement ou indique un changement de performance.
L’enceinte est tombée par terre ou a été endommagée.
17. Entretien - L’utilisateur ne doit pas tenter de réparer l’enceinte au-delà de ce qui est décrit dans le
mode d’emploi.
18. Surcharge - Ne pas surcharger les prises murales, les rallonges, ou les prises femelles encastrées
de commodité. On risquerait un incendie ou un choc électrique.
☞
3
Congratulations!
Congratulations on your purchase of a Velodyne subwoofer system. This
system represents the state of the art in home audio reproduction and will
provideyouwithyearsoflisteningpleasurewhenproperlycaredfor. Read
and follow this instruction manual to insure safe and proper system
connection and operation.
Caution!
Pleaseobservethefollowinginstructionstoinsuresafeandpropersystem
operation.
Note: Do not leave unit in direct sunlight or use in high humidity
environments!!!
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture. Toavoidelectricalshock,donotopenspeakerenclosureoramp
chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to
your authorized Velodyne dealer.
Priortoinstallation:
Please unpack the system carefully. This unit is heavy. Use caution when
liftingormovingtoavoidinjury. Removeallstaplesusedtosealthecarton
as they can scratch the cabinet. Please save the carton and all packaging
materials for future use. Packing this unit in any other carton may result
in severe damage when shipping. Record the serial number in the space
provided on page 15 for future reference.
☞
4
Product Features
• 10"(8.5"pistondiameter)subwooferwith2.0"high-tempvoicecoiland
40 ounce motor structure
• Adjustable (50 to 200Hz) low-pass crossover
• Line-level(RCA)inputs
• Speaker-level inputs and outputs with spring loaded terminals
• Signal sensing auto turn on/off
• Variablevolumecontrol
• Selectable phase control (0 or 180°)
°
• Frequency response of 36 - 120 Hz (+/- 3dB)
• Low-pass crossover @ 12dB/octave
• Green power on/ Red power standby mode indicator LED
Prepare for Installation
Your new Velodyne subwoofer provides for a number of installation
options. Read all the installation information below in order to determine
which installation option is best for your system. Remember to perform
all installation procedures with system power turned off to prevent
possibledamage.
Placement
Truesubwoofersoperateatextremelylowfrequencieswhichareprimarily
omnidirectional. Keep in mind that frequency response and output level
can be drastically influenced by placement, depending on the acoustic
properties of the listening room. Typically, the optimum location for a
subwooferistuckedawayinacornerofyourlisteningroom. Thislocation
will usually offer the greatest output levels and optimum low frequency
extension. The worst location for a subwoofer is typically far away from
any walls, and close to the center of your room. Avoid these locations
when possible. When using a pair of Velodyne subwoofers in stereo, it is
preferable to place each subwoofer by the satellite of the same channel.
Caution! This subwoofer has electronics built into the cabinet. Do not
place the cabinet next to sources of heat such as furnace registers,
radiators, etc. Do not place the unit near sources of excessive moisture,
such as evaporative coolers, humidifiers, etc. The power cord should be
routedinsuchawaythatitwillnotbewalkedon,pinched,orcompressed
in any way that could result in damaging the insulation or wire.
☞
5
RegardlessofwhereyouinstallyourVelodynesubwoofer, itmustremain
in an upright position (woofer facing forward). Using, shipping, or
otherwise storing the subwoofer in any other position for an extended
period of time may result in damage to the unit not covered by warranty.
TheVX-10ismagneticallyshieldedtoreducetheamountofstraymagnetic
energy emitted from the speaker's motor structure. This greatly increases
flexibilitywhenplacingtheunitclosetovideomonitorsasthereisverylittle
stray magnetism. Certain types of televisions are particularly sensitive to
stray magnetic fields. If your television produces distorted colors after
installing your subwoofer, simply increase the distance between your
televisionandthesubwoofer,untilnormalcolorandoperationisreturned.
Your new Velodyne subwoofer, like any good speaker system, requires
proper positioning within the listening space to provide maximum
performance. Improperly placed speakers may degrade the sound quality
and reduce your listening pleasure. Depending on the size and type of
furnishings in the room, perfect placement may not be possible. Finding
the best location for your environment will likely require some
experimentation. We suggest you experiment with the location during
setup to find what sounds best to you when seated in your typical listening
position.
Installation
Inputs
Yournewsubwooferisequippedwithspeaker-levelandline-level inputs.
UsetheLINELEVELjackswhenconnectingyoursubwoofertoapre-amp,
signal processor, line-level crossover, or receiver with pre-amp level
outputs. The SPEAKER LEVEL jacks connect directly to the speaker
outputs of any amplifier, integrated amplifier, or receiver. Your amplifier
sectionwillnoticenoadditionalloadingeffectswhenyouusetheseinputs
due to their very high impedance.
Important!!!
Do not use both LINE LEVEL and SPEAKER LEVEL connections
simultaneously!
VolumeControl
This control allows you to balance the output from the subwoofer to the
main speakers/amplifier in your system. This control should be set to
achieve similar output levels from both the main speakers and subwoofer
when listening to music. A good starting point for the volume control is
2or3dotsfromminimum.
☞
6
Low-passcrossover-50to200Hz
Allinputssumtheleftandrightchannelstogether,withtheresultingsignal
passingthroughanadjustablelow-passcrossoverbeforebeingamplified.
Thecrossovercontrolallowsyoutoadjusttheupperlimitofthesubwoofer's
frequencyresponsefrom50to200Hz. Thesubwoofer'sresponsewillbegin
rolling off above the frequency you set this control to. You should set the
crossover frequency to obtain a smooth and seamless transition from the
subwoofer to the main speakers in your system. If your main speakers are
smaller units with limited low frequency output, you may wish to choose
a higher frequency (such as 100-120Hz) than you would with larger
speakers which have greater low frequency output. With larger speakers,
you might start with this control set lower, such as 80Hz.
Phaseadjustment-0
This control allows you to "reverse" the phase of the subwoofer's output
signal180 tocorrectforanypossiblemismatchand resultingcancellation
°/180°
°
between the subwoofer and your main speakers/amplifier. To adjust,
simply listen to the system with music playing, then depress the phase
switch from one position to the other and listen for a change in low
frequency output. The correct position will have a greater amount of
apparent low frequency output.
Autoturnonfunction
The subwoofer will turn itself on automatically when an audio signal is
present. If no signal is present for approximately 8 minutes, the unit will
switchtostandbymode(RedLED).Whileinstandbymode,yoursubwoofer
willdrawveryminimalpower.
Powerswitch(230Vmodelsonly)
Themasterpowerswitchislocatedonthelowerhalfoftheunit. Thisrocker
style switch is the main on/off for the unit. This switch should be set to
position1(up)for"ON"and0(down)for"OFF".
Subwooferoutputs
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Some processors/
receivers, have a "subwoofer out" jack that is internally filtered and
designed to be used with a conventional amplifier and speaker. In some
rare cases, combining both an external crossover and the one internal to
the subwoofer may result in low output and increased noise. In these
installations you may need to bypass the internal crossover in either the
processor or Velodyne subwoofer. In some installations, simply setting
onecrossovertoahigherfrequency(suchas120Hz)willrestoremaximum
performance.
☞
7
Speaker Line-level Connections
When installed in this fashion the satellite speakers will be crossed over
at 80Hz. This removes the lower bass from your amplifier and speakers,
enablingthemtodoabetterjobreproducinghighfrequencies.Byutilizing
thismethodyouwillhaveabi-amplifiedsystem,gainingimprovedpower
and headroom for your system.
Subwoofer Outputs
TheVelodynesubwooferisdesignedtooperateusingthefullrangeaudio
signal for input when using the built-in crossover. Many home theater
processors/receivers (Dolby Digital, DTS, THX) have a "subwoofer out"
jack that is internally filtered and designed to be used with a powered
subwoofer. In some installations, it may be beneficial to have a steeper
ultimate crossover slope. To do this, you can use both your processor's
crossover and the one internal to the Velodyne sub.
(Refer to Figure 2a and 2b, Page 11 and 12 for connection diagram)
Figure 1. Rear panel inputs, output and operational layout.
☞
8
OperationalReferences
(see Figure 1, Page 8)
A
B
SPEAKER LEVEL INPUT terminals
Connect these input terminals to the speaker output terminals of
youramplifierorreceiver.
SPEAKER LEVEL OUTPUTterminals
The speaker-level signal to the front speakers is output from these
terminals.
C
1
LINE INPUT jacks
Connect these jacks to the LINE OUT jacks of the amplifier.
LOW-PASS CROSSOVER
Use this knob to select the high-frequency range at which you wish
to cut-off the signal to the subwoofer.
2
Power indicator
Red: Unit is in standby mode.
Green: Unit is in operation mode.
(automatically turns to STANDBY mode if no signal for 8 min.)
3
4
5
PHASE switch
Select the switch position at which you hear a louder bass sound.
VOLUME LEVEL knob
Use this knob to adjust the output level of the subwoofer.
POWERswitch(230Vmodelonly)
Main power switch. This switch should be turned in the off position
whenthesubwooferisnotbeingusedforextendedperiodsof idletime
to extend the life of the subwoofer..
☞
9
Speaker-level Connection
Connect your Velodyne subwoofer directly to your receiver or integrated
amplifier. Yourreceiveroramplifierwillnotnoticetheadditionalloadof
the subwoofer due to the high input impedance.
Caution!!! Toavoiddamagetoyourmainamplifier,besuretomaintain
correctpolaritywhenmakingallconnections. Red(positive)tored,and
black(negative)toblack. Besurethatallconnectionsaretight,andthat
there are no loose strands or frayed wires.
Interconnect Cables
When installing your new Velodyne subwoofer using the line level
connections, you should always use shielded phono cables. There are
manydecentcablesavailabletoday,mostanyofwhichwillworkperfectly
well. We do recommend that you keep the length of cable as short as
possible to avoid any potential noise problems.
When using speaker level connections, use a decent quality speaker cable
that mates well with the connectors. Be very careful to avoid any loose
strandsorfrayedwireswhichmayresultinashort,whichmaydamageyour
equipment. Cables of extremely large size are typically not required.
Extremely large gauge wire may not properly fit in the binding posts,
resulting in a poor connection and possible short circuits.
Care of Your Subwoofer
Your Velodyne subwoofer does not require any regular maintenance.
Normal dusting or cleaning of the surface for appearance purposes are all
that is required. We suggest you avoid any harsh detergents or chemicals
when cleaning the cabinet. Abrasives, detergents, or cleaning solutions
may damage the finish on the cabinet. We recommend using only a damp
cloth to clean the cabinet.
Duringnormalconditions,yournewsubwoofermaybeleftoncontinuously
withoutanyproblems. Theunitisequippedwithasignal-sensingturnon/
off that will automatically turn on the unit when a signal is present at the
inputs and turn off the unit after several minutes when there is no longer
any signal at the inputs.
☞
10
Figure 2a. Line-level subwoofer connection diagram.
☞
11
Figure 2b. Speaker-level subwoofer connection diagram.
☞
12
Protection Circuitry
Your new subwoofer is equipped with circuitry to provide maximum
performancewithgreatestreliability.
The unit is protected against:
1) Overheating the amplifier.
2) Excessive drop in power line voltage.
Ifeitheroftheaboveshouldhappen,youshouldreducethevolumesetting
orshuttheunitoffuntilnormaloperatingconditionsreturn. Youmayalso
want to plug the unit into a different wall outlet, as dropping power line
voltagewillbemostnoticeableunderstrenuousconditionsandmayresult
in the unit shutting down intermittently.
Troubleshooting and Service
If you should experience a problem with the operation of your subwoofer,
please check all of the following before seeking service. Following is a
simple troubleshooting guide to assist you.
1. Verify unit is plugged in, power outlet used is active, and supplying
proper voltage.
2. Is power switch on? (230V model)
3. Is unit receiving an input signal from your source?
4. Have all controlson subwoofer(volume, crossover, phase, etc.)been
properly set?
5. If unit has been running at high levels for an extended period of time,
one of the protection circuits may be engaged.
• Is the built-in amplifier extremely hot to the touch?
• Is your power line voltage sagging below acceptable levels?
If the protection circuitry is active, the unit may cycle on and off until
operatingparametersreturntonormal. Undermoreseriousconditions,the
unit may shut off completely. Normal operation should return upon
cooling, but you may be required to turn the power off and then on again
to reset the unit.
☞
13
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a marked
change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
SPECIFICATIONS
VX-10
Cabinet Design
Bass-reflex with built-in power amplifier
36Hz - 120Hz (+/- 3dB)
50-200Hz (variable)
Frequency response
Crossover frequency
Maximum output power
150 Watt (dynamic)
Phase
0
°
or 180°
Input impedance
1.2K ohm
(for SPEAKER LEVEL INPUT terminals)
65K ohm
(for LINE INPUT jacks)
Sensitivity
Speaker-Level
Line
1.6V
230mV
Speaker
10" (8.5" piston diameter)
120V 60Hz AC
75 Watt
Power Supply
Power consumption
Cabinet (H,W,D)
15"
x
12"
x
17"
381mm x 304.8mm x 431.8mm
Weight (approx.)
35 lbs.
Specifications are subject to change without notice.
Thank you for purchasing a
Velodyne VX-10 Subwoofer!
☞
14
WARRANTY STATEMENT (LIMITED WARRANTY)
VELODYNE ACOUSTICS, Inc. ("VELODYNE") warrants all powered subwoofers
for a period of two years, and full range/satellite speakers for a period of five years.
All VELODYNE products have a warranty from the date of purchase against defects
in materials and workmanship subject to the following conditions:
1. VELODYNE is not responsible for defects which result from the use of an
amplifier or controller other than the one originally supplied with the unit
(subwoofer) or defects which result from modifications or repairs made by any
component of the system by anyone other than a VELODYNE factory authorized
service representative.
2. This warranty is void if any repairs or service covered by the terms of this
warranty are made to any component of the system by anyone other than a
VELODYNE factory authorized service representative..
3. VELODYNE is not responsible for damage caused by accidents, abuse, misuse,
natural or personal disaster or unauthorized modification. The VELODYNE products
are not intended for professional or commercial use and VELODYNE is not
responsible for damage resulting from such use.
4. The VELODYNE product warranty is limited to units that are purchased from
authorized VELODYNE dealers and finalized within authorized dealer locations.
5. This warranty is nontransferable under any condition.
TO OBTAIN SERVICE
Information regarding service may be obtained from the dealer from which you
purchased the unit, or by contacting VELODYNE customer service. Warranty service
must be performed by a VELODYNE factory authorized service representative within
the warranty period set forth in the warranty statement. If VELODYNE determines
the unit is defective, VELODYNE will, at VELODYNE's option, repair or replace the
product at no charge if the product is forwarded prepaid to a factory authorized service
representative. Keep original receipt. Products forwarded to the factory authorized
service representative should be shipped securely and properly packaged, insured, and
freight prepaid. Use of original packaging materials is highly recommended. Online
registration is not required to validate warranty, but is recommended. Registration
provides us with purchase and dealer information to assist us when validating your
warranty for covered repairs.
SerialNumber:__________________
Register.......ONLINE
It's faster....and easier
☞
15
Other Velodyne Subwoofer Products:
CHTSeries
CHT-8
SPL Series
SPL-800
CHT-10
SPL-1000
CHT-12
SPL-1200
CHT-15
SPL-523Satellites
CHT Front Row System
HGS Series II
HGS-10
HGS-12
HGS-15 THX Ultra 2
HGS-18 THX Ultra 2
DecoSystem
Deco System
Deco Satellites
☞
16
NOTES
☞
17
NOTES
18
"Itdeliveredroom-shakingbassanddramaticallydemonstratedthe
effectiveness of a single subwoofer placed to one side of the room."
- Julian Hirsh
Stereo Review, January 1997
"In general, the Velodyne could play slightly louder, and often
cleaner, than the Sunfire."
-D.B. Keele, Jr.
Audio/June 1998
"Howdotheygetthiskindofbassoutofsuchatinybox?Deep,tight,
tuneful and loud enough to rattle pictures on the wall--this is serious
subwoofing."
-Robert Deutsch
Stereophile Guide to Home Theater/September 1998
Velodyne Acoustics, Inc.
345 Digital Drive
Morgan Hill, CA 95037
408.465.2800 voice
408.779.9227 fax
408.779.9208 service fax
Service e-mail: [email protected]
Product e-mail: [email protected]
Printedonrecycledpaper
P/N 63-VX10 Rev D 16MAY03
|