VTech Telephone 1411 User Manual

INTRODUCTION  
BELT PACK FEATURES  
REPLACINGTHE BELT PACK BATTERIES  
Parts Check List:  
To purchase replacement battery packs, call  
VTECH Communications at 1-800-595-9511.  
In Canada, callVTECH Electronics at 1-800-  
267-7377.  
and the ( - ) and ( + ) symbols should be  
VOLUME CONTROL  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Belt Pack  
facing you. Angle the lower end of the  
battery pack in first , then push the upper  
portion into the compartment.  
There are 4 volume levels.  
Base Unit  
Telephone line cord  
Headset  
AC adapter  
Battery Pack  
Belt Clip  
PHONELED  
While on a call, press the Up or  
Down key to adjust the listening  
volume.The Belt Pack will emit a double  
beep when the maximum or minimum  
volume level has been reached.  
PHONE/FLASH  
KEY  
VOLUME  
KEY  
4. Replace the battery cover .  
CHANNELKEY  
5. The new battery pack must be charged  
before using your telephone. Place the  
Belt Pack in the cradle of the base unit to  
allow it to charge for 16 hours.  
HEADSET  
JACK  
OFFKEY  
PROGKEY  
MEMORY  
KEY  
REDIALKEY  
OFF KEY  
Press the OFF key to exit all modes of  
operation.  
NOTE: Belt Clip must be detached to  
access Battery Pack.  
IMPORTANT: CHARGE THE BELT PACK  
WITHTHE BELT CLIP ATTACHED!!  
PHONE LED  
While holding the Belt Pack with one  
hand, gently pry the belt clip up and  
away from the top edge (antenna  
edge) of the Belt Pack.The lower claw  
should now easily separate from the  
bottom of the Pack.  
The PHONE LED lights when the Belt  
REDIAL / PAUSE KEY  
Pack is on an active call.  
CAUTION: To reduce the risk of fire or injury,  
read and follow these  
instructions:  
When you hear the dial tone, pressing the  
REDIAL key will dial out the last number  
that was called on your phone.  
It can also be used to store the last number  
dialed into the speed dial memory. See  
Storing a Redial Number into Speed  
Dial for details.  
It flashes in cadence with an incoming  
ring.  
It flashes quickly during PROG mode.  
It flashes slowly when battery is low.  
1. Use only VTECH battery.  
BELTPACK  
2. Do not open or mutilate the battery.  
Released electrolyte is corrosive and may  
cause damage to the eyes or skin. It may  
be toxic if swallowed.  
3. Exercise care in handling batteries in  
order not to short the battery with  
conducting materials such as rings,  
bracelets, and keys. The battery or  
conductor may overheat and cause  
burns.  
When replacing the Belt Clip , begin  
by hooking the lower claw of the clip  
onto the bottom edge of the Belt Pack,  
then snap the top of the clip into the  
notch located on the top edge of the  
Pack  
PHONE KEY/ FLASH KEY  
Press the PHONE key to make a call.  
If you are currently on a call, pressing  
PHONE flashes the line. This would be  
used with a feature like call waiting to  
answer your second call.  
You can store a PAUSE into your dialing  
number.See Storing Pauses in Memory  
for detail.  
CHAN KEY  
1. Remove the battery cover.  
Pressing the CHAN key when the Belt  
2. Remove the old battery pack. Don't put  
the old battery pack in a trash compactor  
or a fire - it could burst.  
3. Place the new battery pack into the  
compartment. The two exposed metal  
contacts should be on the bottom edge,  
PROG KEY  
Press PROG key to enter PROGRAM  
Pack is in use will activate a channel  
change to the next free channel.  
4. Do not dispose of the battery in a fire.The  
cell may explode.  
mode. See Programming Speed Dial  
Numbers for more details.  
This is used if you are experiencing noise  
or interference on the current channel.  
HEADSET  
1
6
7
IMPORTANT SAFETY INSTRUCTIONS  
IMPORTANT SAFETY INSTRUCTIONS  
BELT PACK FEATURES  
BASE UNIT FEATURES  
a) When the power supply cord or plug is damaged or frayed.  
b) If liquid has been spilled into the product.  
c) If the product has been exposed to rain or water.  
When using your telephone equipment, basic safety precautions should always be followed to  
reduce the risk of fire, electric shock and injury to persons, including the following:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the product.  
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol  
cleaners. Use a damp cloth for cleaning.  
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming  
pool).  
5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing  
serious damage to the product.  
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To  
protect it from overheating, these openings must not be blocked by placing the product on the  
bed, sofa, rug, or other similar surface. This product should never be placed near or over a  
radiator or heat register. This product should not be placed in a built-in-installation where  
proper ventilation is not provided.  
7. This product should be operated only from the type of power source indicated on the marking  
label. If you are not sure of the type of power supply to your home, consult your dealer or local  
power company.  
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord will  
be abused by persons walking on it.  
9. Never push objects of any kind into this product through cabinet slots as they may touch  
dangerous voltage points or short out parts that could result in a risk of fire or electric shock.  
Never spill liquid of any kind on the product.  
IN USE/CHARGING LED  
LOW BATTERYWARNING  
MEM KEY  
The IN USE/CHARGING LED illuminates  
steadily when the Belt Pack is in the base  
cradle to indicate that the Belt Pack  
battery is being charged.  
In a low battery state, the Belt Pack will  
emit two beeps when you press PHONE,  
to let you know that the battery pack needs  
to be recharged.  
Press the MEM key to enter MEMORY  
mode.  
The sequence for dialing out a speed dial  
number in memory is: PHONE, MEM,  
Number Button (0-9).  
d) If the product does not operate normally by following the operating instructions. Adjust  
only those controls that are covered by the operating instructions because improper  
adjustment of other controls may result in damage and will often require extensive work  
to restore the product to normal operation.  
e) If the product has been dropped and the cabinet has been damaged.  
f) If the product exhibits a distinct change in performance.  
The LED illuminates whenever the Belt  
Pack is being used.  
It also flashes with the cadence of the  
incoming ring.  
TONE/* KEY  
In PULSE dialing mode, this key is used  
to switch to Temporary TONE dialing  
mode.  
PAGE KEY  
13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may  
be a remote risk of electric shock from lighting.  
14. Do not use the telephone to report a gas leak in the vicinity of the leak.  
Press the PAGE key to page the Belt  
Pack.  
Press it second time to cancel a page.  
The base will ring the Belt Pack for 1  
minute before ending the page  
automatically.  
CUT  
CUT  
REPLACEMENT BATTERY ORDER FORM  
SAVE THESE INSTRUCTIONS  
For VT 1411 Cordless Telephone  
Name:  
City:  
Address:  
The Belt Pack can also cancel the page  
by pressing the OFF key.  
State:  
Zip:  
Daytime Phone Number: (  
ORDER INFORMATION  
For Model VT 1411  
)
(QTY.) Batteries @$19.95 each ................................................. $  
Shipping/Handling @$ 4.95 per battery ....................................................... $  
METHOD OF PAYMENT: DO NOT SEND CASH  
10. To reduce the risk of electric shock, do not disassemble this product. If service or repair work  
is required, contact VTech Customer Service at 1-800-595-9511. Opening or removing  
cabinet parts other than specified access doors may expose you to dangerous voltages or  
other risks. Incorrect reassembling can cause electric shock when the appliance is  
subsequently used.  
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric  
shock.  
12. Unplug this product from the wall outlet:  
CHECK/M.O.  
VISA  
MASTERCARD  
DISCOVER  
EXP. DATE  
AMERICAN EXPRESS  
Credit Card#  
CARD HOLDER’S SIGNATURE  
PLACE ORDER FORM AND PAYMENT IN ENVELOPE AND SENDTO:  
VTECH COMMUNICATIONS INC.  
8770 SW NIMBUS AVENUE  
BEAVERTON,OREGON 97008-7195 USA  
YOU MAY ALSO ORDER BY PHONE. CALL 1-800-595-9511  
3
9
2
8
GETTING STARTED  
GETTING STARTED  
OPERATING INSTRUCTIONS  
OPERATING INSTRUCTIONS  
and press PHONE.The IN USE indicator should light up, and you should hear a dial tone.If  
not, see IN CASE OF DIFFICULTY.  
Changing Channels  
ProgrammingThe RingerType  
The Belt Pack ringer is capable of four  
different types of ringing tones.The following  
sections detail how to change ringing tones  
and turning off the ringer .  
To program, the Belt Pack must be OFF.  
To select a different ringer type do the  
following:  
If you notice interference when using your  
Belt Pack, press CHAN to switch to a clear  
channel.This function is only available when  
you are on a call.  
CAUTION:  
1. Never install telephone wiring during a lightning storm.  
2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet  
locations.  
TONE/PULSE Setting  
3. Never touch uninsulated telephone wires or terminals unless the telephone line has been  
disconnected at the network interface.  
If you have touch tone service on phone line.  
Press PROG, , ,MEM to switch to TONE  
dialing. If you have rotary service, press  
Press PROG  
Press the # key.  
Press a key 1..4 to select a ringer type.  
Press the MEM key to confirm.  
4. Use caution when installing or modifying telephone lines.  
PROG,  
, # ,MEM to switch to PULSE.  
NOTE: Your VT1411 is preset at the factory  
for TONE dialing.  
Turning OffThe Ringer  
To turn off the ringer on the Belt Pack, do the  
following:  
Setting Up Your VT1411  
TemporaryTone  
1. Choose an area near an electrical outlet and a telephone wall jack.  
2. Plug the AC power adapter into an electrical outlet and the DC connector to the back of the  
base unit.  
If you have a rotary (dial-pulse) telephone  
service, (TONE/PULSE setting is set to  
PULSE), this feature allows you to enter  
special codes and tones to operate answering  
machines, use electronic banking services,  
calling cards, or other special services.  
First, dial the call normally.Then activate the  
Temporary Tone feature by pressing TONE  
IMPORTANT:  
Answering Calls  
Make sure the headset is plugged into  
the Belt Pack.VT1411 can only be used  
with the headset.  
Press PROG  
Press the # key  
Press 5 to turn off the ringer  
Press the MEM key to confirm  
To turn the ringer on again, see  
Programming the RingerType.  
When an incoming call is ringing, the IN USE  
LED on the base and PHONE LED on the  
Belt Pack will flash.To make sure your phone  
rings when the Belt Pack is away from the  
base, please keep the base antenna in the  
upright position.  
CAUTION: Use only the AC adapter shipped with your VT1411.It is specifically designed for  
this product.  
NOTE:  
Connect power to the base unit before placing the Belt Pack in the cradle.  
Making Calls  
Wearing your attached Headset, press  
PHONE. When you hear a dial tone, dial the  
number.The PHONE LED will illuminate while  
the Belt Pack is in use.  
If you make a mistake when dialing, press  
OFF to hang up, then press PHONE to get  
the dial tone again.  
3. CHARGETHE BELT PACK BATTERY PACK BEFORE USE. To ensure the Belt Pack is  
recharged properly, make sure the belt clip is attached and the tip of the clip is inserted in the  
slot above charge contacts.The batteries recharge automatically whenever the Belt Pack is  
in the base unit cradle.The batteries must be charged for 16 hours before using your phone  
for the first time.  
4. Connect the telephone line cord. Insert one end of the telephone line cord into the jack at the  
rear of the base unit. Plug the other end into a telephone wall jack. Make sure the plugs snap  
securely into place.  
(the  
key). You can then press the  
CheckingThe Ringer  
To check the ringer which is currently  
programmed, do the following:  
To answer a call , press any key on the Belt  
Pack (except OFF).  
numbers or symbols you need, and your  
phone will send the proper signals.  
To end the call, press OFF or place the Belt  
Pack back in the base. The phone will  
automatically go back to rotary (dial-pulse)  
service.  
Press PROG  
Press the # key  
Press 0  
Disconnecting  
To end a call, either place the Belt Pack in the  
base, or press OFF .  
You must always press PHONE before you  
can dial a call on the Belt Pack.  
Press the MEM key to confirm  
5. CHECK FOR A DIALTONE. After the battery pack is charged, put on the attached Headset  
4
5
 
10  
11  

Teledyne Food Saver DNV 33D User Manual
Thermos Gas Grill 465611003 User Manual
Thomas Betts Water Heater EPW User Manual
Toshiba Air Conditioner RAS 10YAV E User Manual
Toshiba Cash Register EO1 11099 User Manual
Toshiba MP3 Player D VR4 User Manual
Uniden GPS Receiver 1024 User Manual
Universal Electronics Battery Charger 24BC5000TU User Manual
Verbatim Computer Drive External Hard Drive NAS User Manual
ViewSonic Network Card VMAC 1 User Manual