Universal Remote Control Universal Remote UR5U 8500 User Manual

STEP2 Press the [COMPONENT] button (TV,  
VCR, DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED light will  
turn on for 30 seconds indicating the unit  
is ready to be programmed.  
STEP3 Point the remote control toward the  
Component and enter the 3-digit code  
number assigned to your brand.  
STEP5 Save the code. (Same as for 3-Digit Code  
STEP5 Once you have found the correct 3-digit  
code, save it by pressing the [AUX] button  
one more time. The Component LED light  
will blink twice to confirm the code was  
stored. Now when you press the AUX  
CBL : TV  
T V : TV  
VCR : TV  
Introduction  
Button Functions  
4
1
Programming Method - Section A).  
Operating Instructions For  
DVD : TV  
AUX : AUX  
TM  
Now, repeat the Auto-Search Method for those  
Components you could not program earlier  
with the Pre-Programmed Method.  
The CLIKR -5 UR5U-8500 is designed to  
operate Scientific-Atlanta, Pioneer, Voyager  
and Pace Micro digital set top boxes  
(including DVR & HD), plus the majority of TV,  
VCR, DVD and AUDIO equipment on the  
market as shown below.  
If you wish to store the CBL volume control in CBL  
mode, use the following steps.  
STEP1 Press the [CBL] button and the [OK/SEL]  
button simultaneously for 3 seconds. The  
[CBL] Component LED will turn on for 30  
seconds.  
CLIKR-5  
th  
button, all the buttons will work with that 5  
Component.  
C. Finding a Component  
Cable Remote Control  
E. Programming the System On/Off Button  
This allows you to program the System On/Off button  
so it can send up to five power On/Off commands  
with one button press.  
Button’s Setup Code Number  
CABLE : Cable Converters  
TV : Televisions  
*Note : If the 3-digit code number you just entered  
is correct, the Component will turn Off. If it  
did not turn Off, continue entering code  
numbers listed for that brand until the  
Component turns Off.  
STEP2 Press the [VOL +] button.  
If you used the Auto-Search Method to program a  
Component, you may not know what the correct code  
number is. Here is a way for you to identify the code  
number, so you can record it for future reference.  
VCR : VCRs and TV/VCRs  
DVD : DVD Players  
UR5U-8500  
STEP3 Press the [CBL] button.  
The Component LED will blink twice to  
confirm the programming.  
AUX : Audio Receivers and DVRs, etc.  
STEP1 Press the [CBL] button.  
STEP2 Press the [SYSTEM ON/OFF] button and the  
[OK/SEL] button simultaneously for 3  
seconds. The [CBL] button will turn on for  
30 seconds.  
STEP3 Press the first [COMPONENT] button you  
want to store in the [SYSTEM ON/OFF]  
button and then the [POWER] button.  
Repeat this for other Components until you  
have stored all the desired power  
commands into the [SYSTEM ON/OFF]  
button.  
Replacing Batteries  
2
STEP1 Press the [COMPONENT] button (TV, VCR,  
DVD or AUX) you want to verify and the  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED light will turn  
on for 30 seconds.  
To return to original state:  
If you wish to restore the TV volume control in CBL mode,  
repeat the above steps but press [TV] in STEP3  
STEP4 After you’ve entered the correct code  
number and the Component has turned  
Off, press the [POWER] button to turn the  
Component back On. Now it’s time to test  
the VOLUME and CHANNEL buttons for  
the TV (or PLAY and STOP buttons for  
VCR and DVD) to make sure they all work.  
If any of the functions do not work as they  
should, repeat from STEP 3 using the next  
3-digit code number listed for that brand.  
STEP5 Once you have found the correct 3-digit  
code, save it by pressing the same  
[COMPONENT] button one more time.  
The Component LED light will blink twice  
to confirm that the code was successfully  
stored.  
Before you program or operate the remote  
control, you must install two new AA alkaline  
batteries.  
.
H. Programming a ‘Macro’ or Favorite  
Channel  
In CBL mode, the M1, M2, HELP and BLANK  
buttons can be programmed to act as a ‘Macro’ or  
Favorite Channel button. This allows you to send  
up to 10 commands with one button press.  
STEP1 Remove the battery compartment cover  
STEP2 Press the [INFO] button and count the  
number of times the Component LED light  
blinks. This number indicates the first digit  
of the code, followed by the second and  
third, each separated by a one second  
pause when the LED will turn off.  
on the back of your remote control.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
STEP4 Press the [CH+] button to save the power  
commands you stored. The [CBL] button  
will blink twice to confirm the commands  
have been saved.  
STEP3 Replace the battery compartment cover.  
STEP1 Press the [CBL] button to select the CBL  
*Note :10 blinks represents the number zero.  
mode.  
Example : One blink, (pause), eight blinks, ( pause)  
and three blinks, indicates code number  
183.  
STEP2 Press the M1, M2, HELP or BLANK button  
and [OK/SEL] button simultaneously for 3  
seconds. The [CBL] Component LED will  
turn on for 30 seconds.  
STEP3 Press up to 10 buttons you wish to store.  
The [CBL] Component LED will blink once  
for each command entered.  
STEP4 Press the [CH+] button to store the  
commands that were selected. The [CBL]  
Component LED will blink twice to  
confirm the storage of commands.  
F. Programming Channel Control  
Now, program the rest of your Components  
by repeating STEPS 1-5.  
th  
You can program the channel controls (Channel Up,  
Channel Down and Last) from one Component to  
operate in another Component mode. Default channel  
control settings on the remote control are as follows:  
D. AUX Function: Programming a 5  
Component  
*Note : If the Pre-Programmed Method did not  
work, or if the Code Tables do not list your  
Component brand, use the Auto-Search  
Method as explained in Section B.  
You can take advantage of the AUX function to  
th  
program a 5 Component such as a second TV, VCR,  
CBL : CBL  
T V : CBL  
VCR : CBL  
DVD or Audio Component.  
DVD : DVD  
AUX : AUX  
th  
STEP1 Turn on the 5 Component you want to  
B. Auto-Search Method  
STEP1 Turn on the Component you want to  
program (TV, VCR, DVD or AUX) using  
your old remote.  
If you wish to store the TV channel control in TV  
mode, use the following steps.  
STEP1 Press the [TV] button and the [OK/SEL]  
button simultaneously for 3 seconds. The  
[TV] Component LED will turn on for 30  
seconds.  
STEP2 Press the [VOL -] button.  
STEP3 Press the [TV] button again.  
The Component LED will blink twice to  
confirm the programming.  
program (TV, VCR, DVD or Audio) using  
your old remote.  
I. Low Battery Warning  
STEP2 Press the [AUX] button and the [OK/SEL]  
button simultaneously for 3 seconds.The  
[AUX] Component LED will turn on for 30  
seconds.  
When the batteries are low and need to be  
replaced with fresh batteries, the Component LED  
lights will blink 2 times in sequence whenever a  
[POWER] button is pressed to turn on equipment.  
STEP2 Press the [COMPONENT] button (TV,  
VCR, DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED light will  
turn on for 30 seconds indicating the unit  
is ready to be programmed.  
STEP3 Point the remote toward the Component  
and press the [CH] or [CH] button  
one step at a time or keep it pressed. The  
remote will emit a series of ON/OFF  
commands. Release the [CH] or  
[CH] button as soon as the Component  
turns Off.  
Programming the Remote Control  
5
TM  
There are two ways you can program your CLIKR -5 remote:  
Operations  
3
STEP3 Press the [COMPONENT] button you want  
to setup. Point the remote control toward  
the Component and enter the 3-digit code  
number assigned to your brand.  
The Pre-Programmed 3-Digit Code Method  
The Auto-Search Method  
*
*
DEFAULT STATES:  
Component Default: CABLE  
Channel Default: CABLE channel and number  
keys through the CABLE. You have the option  
of controlling your CABLE channel and  
number keys through the TV or VCR. Refer to  
section F for programming steps.  
Volume Default: TV volume and mute keys  
through the TV. You have the option of  
controlling your TV volume and mute through  
the Cable box, VCR or DVD. Refer to section G  
for programming steps.  
J. Memory Lock System  
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit  
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest  
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The  
Auto-Search Method scans through all the codes in the remote control, one at a time.  
This remote control is designed to retain  
programmed memory for 10 years even after  
batteries are removed from the remote control.  
To return to original state:  
*Note : If the 3-digit code number you just entered is  
the correct number, the Component will turn  
Off. If it did not turn Off, continue entering  
code numbers listed for that brand until the  
Component turns Off  
If you wish to restore the CABLE channel control in  
TV mode, repeat the above steps but press [CBL]  
IMPORTANT SETUP NOTE!  
in STEP3  
.
K. Record Your Component Set-up Codes  
This pertains to all programming steps. When you are in setup mode, a component LED will light for  
30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit setup  
mode and you will need to start over.  
G. Programming Volume Control  
TV  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If any  
of the functions do not work as they  
should, repeat from STEP 3 using [CH]  
or [CH] buttons to find the correct code.  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If any  
of the functions do not work as they should,  
you need to find a new code.  
VCR  
DVD  
AUX  
You can program the volume controls (Volume Up,  
Volume Down and Mute) from one Component to  
operate in another Component mode. Default volume  
control settings on the remote control are as follows:  
Universal Remote Control, Inc.  
A. Pre-Programmed 3-Digit Code Method  
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) using your old remote.  
OCE-0045A REV 02 (05/06/06)  
 

Tascam Headphones MH 8 User Manual
Teac Clock Radio SLD80R User Manual
TERK Technologies Satellite Radio XM5 User Manual
Texas Instruments Calculator TMS320C2XX User Manual
TMC Telephone EV4500 User Manual
Toshiba TV DVD Combo MD13N1 User Manual
TP Link Network Card TL WN7200N User Manual
Tripp Lite Flat Panel Television A152 000 2 User Manual
Uniden Cordless Telephone EXAI 5180 User Manual
Wagner SprayTech Paint Sprayer 279029 User Manual