Universal Remote Control Universal Remote UR4U MDVR2 User Manual

STEP2 Press the [COMPONENT] button (TV,  
DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED will light  
for 30 seconds indicating the unit is  
ready to be programmed.  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If any  
of the functions do not work as they  
should, repeat from STEP 3 using [CH]  
or [CH] buttons to find the correct code.  
STEP4 Test functions. (Same as for 3-Digit Code  
Programming Method - Section A). If  
any of the functions do not work as they  
should, you need to find a new code.  
To return to original state:  
Introduction  
Button Functions  
4
1
If you wish to restore the CABLE channel control in  
Operating Instructions  
For 4-Function  
Cable Remote Control  
TV mode, repeat the above steps but press [CBL]  
This remote control is designed to operate all  
Motorola and Scientific Atlanta digital set top  
boxes (including HD and DVR), plus the  
majority of TVs, VCRs, DVDs and AUDIO  
equipment on the market as shown below.  
in STEP3  
.
STEP5 Once you have found the correct 3-digit  
code, save it by pressing the [AUX]  
button one more time. The Component  
LED light will blink twice to confirm the  
code was stored. Now when you press  
the AUX button, all the buttons will work  
STEP5 Save the code. (Same as for 3-Digit Code  
G. Programming Volume Control  
STEP3 Point the remote control toward the  
Component and enter the 3-digit code  
number assigned to your brand.  
Programming Method - Section A).  
You can program the volume controls (Volume Up,  
Volume Down and Mute) from one Component to  
operate in another Component mode. Default  
volume control settings on the remote control are  
as follows:  
CABLE : Cable Converters TV : Televisions  
DVD : DVDs, TV/DVDs, VCRs and TV/VCRs  
AUX : Audio Receivers and DVRs, etc.  
Now, repeat the Auto-Search Method for those  
Components you could not program earlier with  
the Pre-Programmed Method.  
*Note : If the 3-digit code number you just  
entered is correct, the Component will  
turn Off. If it did not turn Off, continue  
entering code numbers listed for that  
brand until the Component turns Off.  
UR4U-MDVR2  
th  
with that 4 Component.  
C. Finding a Component Button’s  
Setup Code Number  
If you used the Auto-Search Method to program a  
Component, you may not know what the correct code  
number is. Here is a way for you to identify the code  
number, so you can record it for future reference.  
CBL : TV  
T V : TV  
Replacing Batteries  
Before you program or operate this remote  
control, you must first install two new AA Alkaline  
batteries.  
2
E. Programming the System On/Off Button  
This allows you to program the System On/Off  
button so it can send up to four power On/Off  
commands with one button press.  
DVD : TV  
AUX : AUX  
If you wish to operate the CBL volume control in  
CBL mode, use the following steps.  
STEP4 After you’ve entered the correct code  
number and the Component has turned  
Off, press the [POWER] button to turn  
the Component back On. Now it’s time  
to test the VOLUME and MUTE buttons  
for the TV (or PLAY and STOP buttons  
for VCR and DVD) to make sure they all  
work. If any of the functions do not  
work as they should, repeat from STEP  
3 using the next 3-digit code number  
listed for that brand.  
STEP1 Press the [CBL] button and the  
[OK/SEL] button simultaneously for 3  
seconds. The [CBL] Component LED  
will light for 30 seconds.  
STEP1 Remove the battery compartment cover  
STEP1 Press the [CBL] button.  
on the back of your remote control.  
STEP1 Press the [COMPONENT] button (TV, DVD  
or AUX) you want to verify and the [OK/SEL]  
button simultaneously for 3 seconds. The  
Component LED will light for 30 seconds.  
STEP2 Press the [SYSTEM ON/OFF] button and  
the [OK/SEL] button simultaneously for 3  
seconds. The [CBL] Component LED will  
light for 30 seconds.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
STEP2 Press the [VOL +] button.  
STEP3 Press the [CBL] button.  
The Component LED will blink twice to  
confirm the programming.  
STEP2 Press the [INFO] button and count the  
number of times the Component LED light  
blinks. This number indicates the first  
digit of the code, followed by the second  
and third, each separated by a one  
second pause when the LED will turn off.  
STEP3 Replace the battery compartment cover.  
STEP3 Press the first [COMPONENT] button you  
want to store in the [SYSTEM ON/OFF]  
button and then the [POWER] button.  
Repeat this for other Components until  
you have stored all the desired power  
commands into the [SYSTEM ON/OFF]  
button.  
To return to original state:  
STEP5 Once you have found the correct 3-  
digit code, save it by pressing the same  
[COMPONENT] button one more time.  
The Component LED light will blink  
twice to confirm that the code was  
successfully stored.  
If you wish to restore the TV volume control in CBL  
mode,  
STEP3  
repeat the above steps but press [TV] in  
.
*Note : 10 blinks represents the number zero.  
Example : One blink, (pause), eight blinks,  
(pause) and three blinks, indicates  
code number 183.  
H. Programming a Favorite Channel  
See on-screen Guide Menu.  
STEP4 Press the [CH+] button to save the power  
commands you stored. The [CBL] button  
will blink twice to confirm the commands  
have been saved.  
Now, program the rest of your Components by  
repeating STEPS 1-5.  
th  
D. AUX Function: Programming a 4  
I. Low Battery Warning  
*Note : If the Pre-Programmed Method did  
not work, or if the Code Tables do not  
list your Component brand, use the  
Auto-Search Method as explained in  
Section B.  
Component  
When the batteries are low and need to be  
replaced with fresh batteries, the Component  
LED lights will blink 2 times in sequence  
whenever a [POWER] button is pressed to turn  
on equipment.  
F. Programming Channel Control  
You can take advantage of the AUX function to  
th  
You can program the channel controls (Channel Up,  
Channel Down, Last and Numbers) from one  
Component to operate in another Component mode.  
Default channel control settings on the remote  
control are as follows:  
program a 4 Component such as a second TV,  
VCR, DVD or Audio Component.  
Programming the Remote Control  
5
th  
STEP1 Turn on the 4 Component you want to  
B. Auto-Search Method  
There are two ways you can program your remote control:  
program (TV, VCR, DVD or Audio).  
J. Memory Lock System  
Operations  
3
STEP1 Turn on the Component you want to  
The Pre-Programmed 3-Digit Code Method  
The Auto-Search Method  
*
*
STEP2 Press the [AUX] button and the [OK/SEL]  
button simultaneously for 3 seconds.The  
[AUX] Component LED will light for 30  
seconds.  
This remote control is designed to retain  
programmed memory for 10 years even after  
batteries are removed from the remote control.  
program (TV, VCR, DVD or AUX).  
CBL : CBL  
DVD : DVD  
T V : CBL  
AUX : AUX  
DEFAULT STATUS:  
Component Default: CABLE  
Channel Default: CABLE channel +/- and  
numbers operate through the CABLE box.  
You have the option of controlling channel +/-  
and numbers through the TV, VCR or DVD.  
Refer to section F for programming steps.  
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit  
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest  
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The  
Auto-Search Method scans through all the codes in the remote control, one at a time.  
STEP2 Press the [COMPONENT] button (TV,  
DVD or AUX) to be programmed and  
[OK/SEL] button simultaneously for 3  
seconds. The Component LED will light  
for 30 seconds indicating the unit is  
ready to be programmed.  
If you wish to operate the TV channel control in TV  
mode, use the following steps.  
K. Record Your Component Set-up  
Codes  
STEP3 Press the [COMPONENT] button you want  
to setup. Point the remote control toward  
the Component and enter the 3-digit code  
number assigned to your brand.  
STEP1 Press the [TV] button and the [OK/SEL]  
button simultaneously for 3 seconds.  
The [TV] Component LED will light for 30  
seconds.  
IMPORTANT SETUP NOTES:  
TV  
Set-up Code Number:  
Set-up Code Number:  
Set-up Code Number:  
This pertains to all programming steps. When you are in setup mode in each component, a  
component LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED  
light will turn off and exit setup mode and you will need to start over.  
STEP3 Point the remote toward the  
Component and press the [CH] or  
[CH] button one step at a time or  
keep it pressed. The remote will emit a  
series of ON/OFF commands. Release  
the [CH] or [CH] button as soon as  
the Component turns Off.  
DVD  
AUX  
*Note : If the 3-digit code number you just  
entered is the correct number, the  
Component will turn Off. If it did not turn  
Off, continue entering code numbers  
listed for that brand until the Component  
turns Off  
Volume Default: CABLE volume +/- and mute  
operate through the TV. You have the option  
of controlling volume through the Cable box,  
VCR or DVD. Refer to section G for  
programming steps.  
STEP2 Press the [VOL -] button.  
When programming a combo unit, program as a VCR or DVD first.  
Universal Remote Control, Inc.  
STEP3 Press the [TV] button again.  
The Component LED will blink twice to  
confirm the programming.  
A. Pre-Programmed 3-Digit Code Method  
OCE-0053B REV 04 (10/10/07)  
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX) .  
 

Tascam DVR DA 38 User Manual
Texas Instruments Personal Lift DAC8555EVM User Manual
Toshiba Camcorder Camera Camcorder User Manual
Toshiba CRT Television 20AF44 User Manual
Toshiba Security Camera CS8560D User Manual
TRENDnet Router TEW 647GA User Manual
Tunturi Home Gym R 710 User Manual
Viking Ice Maker F20733EN User Manual
Vision Fitness Exercise Bike U70 User Manual
VTech Cordless Telephone VT 1900 User Manual