Universal Remote Control Universal Remote UR3 EXP User Manual

STEP1 Press the [CBL] button.  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your  
brand from the code tables.  
STEP4 Press the same [DEVICE] button  
to store the code. The Device  
LED will blink twice to confirm  
that the code has been stored.  
Introduction  
Button Functions  
3
1
Operating Instructions  
For 3 Function  
Cable Remote Control  
STEP2 Press the [SYSTEM] button and the  
[SELECT] button simultaneously for 3  
seconds. The [CBL] button will turn  
on for 20 seconds.  
The remote control is designed to operate the  
Scientific-Atlanta Explorer 2000 and 3000  
Series and the Pioneer Voyager set top boxes  
and the majority of TV and VCR/DVD equipment  
on the market.  
*Tip : The equipment will turn off when the  
correct three-digit code number has  
been entered. You can verify you have  
selected the correct code by pressing  
the [MUTE] button, the equipment  
should turn on or turn off.  
*Note : If there is more than one three-digit  
number listed for your brand, try one  
code number at a time until your  
equipment turns off.  
C. To Find the Three Digit Code  
Number That was Stored in  
the Device.  
STEP3 Press the [DEVICE] button you wish  
to store in the System On/Off button  
and repeat this until you stored all  
the power commands into the  
System On/Off button.  
UR3-EXP  
Replacing Batteries  
Before you program or operate the remote control,  
you must install two new AA alkaline batteries.  
STEP1 Press the [DEVICE] button (TV or  
VCR) you wish to verify and the  
[SELECT ]button simultaneously for 3  
seconds.  
2
STEP4 Press the [CH+] button to save the  
power commands you stored. The  
[CBL] button will blink twice to  
confirm the saving.  
STEP1 Remove the battery compartment cover  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
on the back of your remote control.  
STEP4 Store the three-digit code number  
by pressing the same [DEVICE]  
button once again. The device LED  
will blink twice to confirm that the  
code has been stored.  
STEP2 Check battery polarity carefully, and  
install the batteries as shown in the  
illustration below.  
F. Volume Punch Through:  
STEP2 Press the [INFO] button.  
By following the steps below, the user can  
program the volume controls (Volume UP,  
Volume Down and MUTE) from one device to  
operate in another device mode.  
The device LED will blink number of times  
indicating the number of each digit of the  
code number. Each digit is separated by a 1  
second interval of the LED being turned off.  
Example : One blink, three blinks and eight  
blinks with an interval of 1 second  
of LED being turned off, indicates  
the code number 138.  
STEP3 Replace the battery compartment cover.  
*Note : Try all the functions on the remote  
control. If any of the functions do not  
work as they should, repeat from Step 2  
using the next three-digit code number  
from the same brand list. Make sure  
that the VCR/VOD button is in the  
VCR position when using your VCR.  
The default volume control settings on the  
remote control is TV volume control. If you  
wish to store the CABLE volume control in  
CBL mode, use the following steps.  
STEP1 Press the [CBL] button and the  
[SELECT] button simultaneously for  
3 seconds.  
Note : Ten blinks is equal to the number 0.  
B. Auto Search Method.  
*Tip :The device LED will light on for 20  
seconds. The next step must be  
entered while the LED is on.  
D. Programming a second TV  
to VCR Mode.  
STEP1 Press the [VCR] button to be  
programmed and the [SELECT]  
button simultaneously for 3 seconds.  
*Tip : The device LED will turn on for 20  
seconds. The next step must be  
entered while the LED is on.  
If the three-digit code numbers assigned to  
your brand do not turn off your equipment or  
the code tables do not list your brand, you  
can use the Auto Search Method to find the  
correct three-digit code number for your  
equipment by the following steps:  
STEP2 Press the [VOL +] button.  
STEP3 Press the [CBL] button.  
The device LED will blink twice to  
confirm the programming.  
STEP1 Turn on the equipment you wish to  
operate.  
To return to original state:  
STEP2 Press the [DEVICE] button (TV or  
VCR) to be programmed and the  
[SELECT] button simultaneously for 3  
seconds. The device LED will turn on.  
If you wish to restore the TV volume control in  
STEP2 Press the [TV] device button to  
CBL mode, repeat the above steps by  
pick up the TV code table.  
Operations  
Default State :  
Device Default : Scientific Atlanta Explorer  
2000/3000 & Pioneer Voyager  
4
pressing [TV] in STEP 3 .  
STEP3 Point the remote control toward the  
equipment and enter the three-digit  
code number assigned to your TV  
brand from the code tables.  
STEP4 Store the three-digit code number by  
pressing the [VCR] button once again.  
The device LED will blink twice to  
confirm that the code has been stored.  
*Tip : The device LED will light on for 20  
seconds. The next step must be  
entered while LED is on.  
Programming the Remote Control.  
5
G. LOW BATTERY WARNING:  
When the battery is low (2.0V-2.3V) and  
needs to be replaced with fresh batteries,  
the remote control LED will blink 2 times in  
sequence whenever a [DEVICE] button is  
pressed to turn on equipment.  
A. Three-Digit Code Programming Method.  
The remote control can be programmed by pressing in a three digit code number that  
corresponds to particular manufacturers and brands of Audio/Video equipment.  
The three-digit code numbers are listed in the code table of the instruction manual.  
Volume Default : TV volume and mute through  
the TV, with the option of controlling volume and  
mute through the Cable Converter. Refer to  
Section F for programming the volume and mute  
through your Cable Converter.  
STEP3 Point the remote control toward the  
equipment and alternately press the  
[CH+] (or [CH-]) button and the  
[MUTE] button. If the right code  
number is sent, the equipment will  
turn off.  
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)  
H. Memory Lock System:  
E. Programming the System On/Off Button.  
System On/Off button :  
STEP2 Press the [DEVICE] button (TV or VCR) to be programmed and the [SELECT] button  
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready  
to be programmed.  
This remote control is designed to retain  
programmed memory for 10 years even  
after batteries are removed from the  
remote control.  
This is designed to program the System on/off  
button so that it can send out up to three  
power on/off commands for the devices you  
programmed into the remote control.  
*Tip : You can verify that you selected the  
correct code by pressing the [MUTE]  
button again. The equipment should  
either turn on or turn off.  
Universal Remote Control, Inc.  
This button is designed to send out power  
commands for two or all three devices with one  
button press. Please refer to section E for details.  
OEE-0049A Rev 07(06/30/04)  
*Tip : The device LED will stay lit for 20 seconds. The next step must be entered while the LED is on.  
 

Taylor Blender shake slush freezer User Manual
TC electronic SDN BHD Electronic Keyboard Multi Tap Delay User Manual
Teledex Conference Phone Pearl S User Manual
Toastmaster Food Warmer THMP2 User Manual
Toastmaster Hot Beverage Maker 597U User Manual
Toshiba Blu ray Player BDX5500KC User Manual
Toshiba TV DVD Combo 17HLV85 User Manual
TRENDnet Network Hardware Powerline Network Solution User Manual
Turbosound Speaker TCS C35T User Manual
Vanguard Heating Oven SDVBNA User Manual