MODEL HS-303
AUTOMATIC LIGHTCONTROL
INSTRUCTION MANUAL
Installation - Turn light switch off (unplug lamp). Screw into standard
light socket (120 Volt, 60 Hz). Screw light bulb into Automatic Light
Control. Not recommended for 3-way light bulbs.
Operation - The HS-303 senses light through three windows. Each
window has a shutter which slides open or closed to adjust the
amount of light entering the sensor. If too much reflected light from
adjacent lights or lampshades is entering through the unit, slide the
shutters closed until the problem is corrected.
Note - At dawn and dusk, the bulb may flicker slightly or appear
partially bright for a few minutes as the HS-303 switches on or off.
This is normal.
Note - Your light will not be as bright when you install the Automatic
Light Control. Use a larger bulb to increase brightness (up to 150
Watt incandescent).
CAUTION - Always turn the power (light switch) off before adjusting
the Automatic Light Control or changing the controlled light bulb. Do
not install or adjust if unit or lamp is wet. Do not use with fluorescent
lights, appliances or any other non-incandescent lights.
WARNING - To prevent fire or electric shock hazards, do not expose
this product to rain or moisture, or disassemble. No user serviceable
parts inside. Refer servicing to qualified service personnel.
WARNING - Read instructions carefully before installing the
automatic switch. Safety first - unplug the lamp when installing the
switch. For indoor and protected outdoor use. To avoid overheating
and possible damage from fire or to the lamp, do not exceed the
maximum incandescent load rating of the switch.
Indoor Use - The HS-303 can switch a table lamp on and off to
simulate home occupancy during vacations, weekends away, etc.
The lamp must be unshaded and placed so that the Automatic Light
Control lens is facing directly toward a window less than 3 feet away.
LIMITED 90 DAY WARRANTY
Universal Security Instruments, Inc. ("Universal") warrants your
Universal product to be free from defects in material and
workmanship for a period of ninety (90) days from the date of
purchase. This warranty applies only to the original consumer purchaser
and only to products used in normal residential use and service. If this
product is found to be defective, Universal's only obligation, and your exclusive
remedy, is the repair or replacement of the product, at Universal's discretion,
provided that the product has not been damaged through misuse, abuse,
accident, modifications, alternation, neglect or mishandling. This Warranty
shall not apply to any product which is found to be improperly installed, set-
up, or used in any way not in accordance with the instructions supplied with
the product. For repair or replacement, send the defective product to Universal
Security Instruments, Inc., 7-A Gwynns Mill Court, Owings Mills, Maryland
21117, postage prepaid, with a payment of $5.00 to cover the costs of return
postage and handling. You must include a proof of purchase (receipt) along
with the returned product.
UNIVERSAL DOES NOT WARRANTAND SPECIFICALLY DISCLAIMS ANY
WARRANTY, WHETHER EXPRESS OR IMPLIED, OF FITNESS FOR A
PARTICULARPURPOSEOTHERTHANTHEWARRANTYCONTAINEDHEREIN.
NO IMPLIED WARRANTY ON THIS PRODUCT, CREATED BY STATE LAW,
SHALL EXTEND BEYOND THE TERM OF THIS WARRANTY UNLESS SUCH
LAW OTHERWISE PROVIDES. UNIVERSALSPECIFICALLY DISCLAIMSANY
LIABILITY AND SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTALLOSSORDAMAGE, INCLUDING, BUTNOTLIMITEDTO, DAMAGES
TOANYEQUIPMENTWITH WHICHTHIS PRODUCT IS USED.
Some states do not allow the exclusion or limitation of incidental or
consequential damages so the above limitations or exclusions may not apply
to you.
No agent, representative, dealer or employee of Universal has the authority
to increase or alter the obligations or terms of this Warranty.
This Warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
This Warranty is only valid for merchandise purchased from outlets in the
United States and Canada.
©1995 UNIVERSAL SECURITY INSTRUMENTS, INC
288-3144-00A
Printed in China
|