550W
FCC Information
Important: Changes or modifications to this unit not expressly approved by Uniden could void your
authority to operate this unit. Do not open your radio to make any internal adjustments. Your radio is
set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust
the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made
by qualified technicians using the proper test equipment. To be safe and sure:
•Never open your radio’s case.
•Never change or replace anything in your radio except the batteries.
Your radio might cause TV or radio interference even when it is operating properly. To determine
whether your radio is causing the interference, turn it off. If the interference goes away, your radio is
causing it. Try to eliminate the interference by moving your radio away from the receiver. If you
cannot eliminate the interference, the FCC requires that you stop using the radio.
Audio Accessories: Do not operate the radio with audio accessories at high volume levels. Hearing
experts advise against continuous high volume operation. If you experience a ringing in your ears,
reduce the volume level or discontinue use. Always make sure the radio is turned off before plugging
audio accessories into the accessory jack.
Do not operate the radio in hazardous environments. Explosion or fire may result. Do not
operate the radio near unshielded electrical blasting caps. Under certain conditions,
radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to
prevent accidental transmission when in a blasting area or in areas posted: “Turn off two-way radio.”
Construction crews often use remote control RF devices to set off explosives.
Care and Safety: To clean the radio, use a soft cloth dampened with water. Do not use cleaners or
solvents because they can harm the body of the unit and leak inside, causing permanent damage. Use
a dry, lint-free cloth to clean the battery contacts.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Included in Your Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Low Battery Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Using Your Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Turning the Radio On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
• Choosing a Channel and CTCSS . . . . . . . . . . . . . . . . . . . . . . 7
• Scan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
• Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
• Talking on Your Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
• VOX Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
• Vibration Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
• Locking In Your Selection . . . . . . . . . . . . . . . . . . . . . . . . . 12
• Call Tone Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
• Monitoring Weather Channels . . . . . . . . . . . . . . . . . . . . . . . 13
• Silent Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
• LCD Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
• External Microphone and Speaker (Optional) . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 5
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 6
Appendix - FCC Part 95 Subpart B . . . . . . . . . . . . . . . . . . . A-1
1
Welcome
Congratulations on your purchase of the Uniden FRS550W family radio. This product is a
lightweight, palm-sized radio you can carry almost anywhere. Use it at shopping malls,
amusement parks, or sporting events to stay in contact with family and friends, or in a
neighborhood watch for vital communications. This compact, state-of-the-art device is
equipped with the following features:
• 14 Preprogrammed Channels
• VOX Feature
• 38 Built-in CTCSS Codes
• 7 Weather Channels
• Up to 2 mile range*
• LCD Display
• Tone/Vibration Alert for incoming calls
• Channel Scan
• Keypad Lock
• 50 hours of operation
• Low Battery Level Indicator
• LCD Backlit
• Silent Keypad
• External Speaker and Microphone Capable
* Range may vary depending on environmental and/or topographical conditions.
2
Included in Your Package
Your package contains the FRS550W, this reference guide, and the accompanying belt clip
with hardware. You will need to purchase three (3) AA ALKALINE batteries in order to
operate the unit. If any of these items are missing or damaged, contact the Uniden Parts
Department at (800)554-3988 M-F: 7:00 AM-5:00 PM CST.
Belt clip and screws
FRS Unit
3
Battery Installation
Your FRS550W radio uses three (3) AA ALKALINE batteries for power.
To install the batteries:
1. Make sure your radio is off.
Do not mix old and new batteries to avoid damage to the unit.
2. Release the battery cover clip, then
remove the battery cover.
3. Insert three (3) AA ALKALINE batteries
according to the polarity symbols on the
inside of the battery compartment.
4. Align the battery cover tabs with the
FRS550W tab holes then replace the cover.
Tab holes
4
Low Battery Alert
The LCD on your radio shows a battery meter
in the lower right corner. The
indicates a fully powered unit. As the batteries
become low, will flash.
icon
When the batteries in the unit are low, the unit will go into a Battery Low/Sleep Mode. The
Scan Mode, Monitor Mode, Transmit, Transmit Call Tone Mode, CTCSS Tone Setting Mode,
VOX Sensitivity Level Setting Mode, and Vibration are disabled. Replace the batteries
immediately to continue using the radio.
Belt Clip
Because you will most likely use your radio when you are out and about, the unit comes
equipped with a belt clip to fasten the unit to your belt, pocket, or purse.
To remove the belt clip, turn the screws counterclockwise.
To attach the belt clip:
1. Insert the belt clip screws into the slot
on the belt clip.
2. Align the screws with the holes on the
back of the radio and turn them
clockwise, using a Phillips screwdriver to
secure the belt clip. Do not over-tighten.
5
Using Your Radio
To get the most out of your new radio, read this reference guide completely before
attempting to operate the unit.
Turning the Radio On
2
1
1. Turn the on/off volume control
clockwise to turn the unit on.
When you turn on your FRS550W, the LCD backlight remains lit for
5 seconds.
2. Turn the control counterclockwise to turn the unit off.
Adjusting the Volume
1. Press the MON button to hear
background noise. The “BUSY” icon
and
icon appear.
2. Turn the on/off volume control
clockwise to increase the volume and
counterclockwise to decrease the volume.
You may need to adjust the volume again when audio is heard from
the speaker.
6
Choosing a Channel and CTCSS
Your radio has 14 channels and a Continuous Tone Coded Squelch System (CTCSS) that
you can use to talk to others. You can only communicate with radios that are set on the
same channel and CTCSS tone code. A CTCSS tone is subaudible and selectable from the
38 standard tone frequencies. You must select the same channel as your party selected.
To choose a channel for the FRS550W:
Press the up or down button repeatedly to
select one of the 14 channels. (The number
on the LCD changes to indicate that a new
channel has been selected.)
The BUSY icon and
icon appear while receiving a transmission.
To choose a CTCSS code for the FRS550W:
You may want to hear calls from specific persons in your group. The CTCSS code that you
enter allows you to block other calls and only receive from those who are using the same
channel and CTCSS code.
This feature does not cause your conversation to be private. Anyone else
on the channel will be able to listen. It only relieves you of listening to
unwanted conversations.
7
1. Press and hold the wx/ctcss button for
2 seconds. The code indicator flashes.
2. Press the up or down button repeatedly to select one of the CTCSS codes (0-38).
3. After selecting the desired CTCSS code, press the wx/ctcss button again. The code
indicator stops flashing.
You must press the wx/ctcss button within 10 seconds or the unit will
time out. If not, the setting will not be made.
4. To turn off the CTCSS code, press the
up or down button until the code
is selected. Then press the wx/ctcss
button again. The code indicator
stops flashing.
If the code is selected on your radio, you can receive any signal on
that channel regardless of the CTCSS code settings of the people in
your party.
8
Scan Mode
Your radio also allows you to scan for activity from other transmitting radios regardless of
the channel and code setting.
Make sure all of your CTCSS codes are set to “0” prior to scanning. Otherwise, during a
scan cycle, your radio will only check for that specific channel and code combination.
To use the Scan feature:
1. Press the scan/vibrate button to begin
scanning channels. The LCD will
indicate that you are in scan mode.
If a signal is present, the radio will stop
on the active channel. It will remain on
the channel until the transmission ends.
After 2 seconds, it will resume scanning.
2. To resume scanning prior to the transmission end, press scan/vibrate again.
3. Press the scan/vibrate, wx/ctcss, call/vox, PTT, up, or down button to exit the
scan mode, stopping at the current channel.
If you press scan/vibrate to exit the scan mode, the radio must be
actively scanning.
9
Monitor Mode
The Monitor Mode is used to check activity on a specific channel. It will allow you to receive
signals that are considered too weak.
To check the channel activity:
1. Press and hold the MON button until you hear a series of beeps. You will hear
background noise if the channel is clear. Don’t transmit if you hear conversation.
2. To turn Monitor Mode off, press the MON button again.
Talking on Your Radio
To talk to others using the radio;
1. Determine your communicating channel and/or code setting with the other members
of your party (refer to “Choosing a Channel and CTCSS” on page 7).
2. Press and hold the PTT button and
speak into the microphone. The
following LCD screen appears.
3. When you finish speaking, release the PTT button. You cannot hear any signals while
your PTT button is pressed.
4. Repeat steps 2 and 3 to continue communication.
10
VOX Feature
The built-in Voice Activated Circuit (VOX) feature enables you to transmit automatically
by speaking on the microphone of a VOX headset (not supplied) without pressing the
PTT button.
To activate this feature:
1. Turn off the radio. Open the SPKR/MIC
cover and plug in a VOX headset
(not supplied).
2. Turn on the radio while pressing the
call/vox button. The VOX icon appears.
3. To set the VOX sensitivity level, press the
call/vox and scan/vibrate buttons
simultaneously until the VOX icon and
number indicator begin to flash.
4. Within 10 seconds, select one of the level numbers,
1 (the lowest sensitivity) ~ 9 (the highest), using the up or down button.
5. To complete the entry, press the scan/vibrate or call/vox button. Now the radio is
ready for automatic transmission.
6. To deactivate the VOX feature, turn the radio off, then on again while pressing
the call/vox button. The VOX icon is no longer displayed.
Don’t press the PTT button while VOX is activated.
11
Vibration Alert
Your FRS550W will alert you with a vibration when there is an incoming transmission.
You must be on the same channel and code setting as the party with whom you
are communicating.
To use the vibration alert:
1. Press and hold the scan/vibrate
button until the
icon appears.
2. You will be alerted with a five second vibration when you receive an incoming call.
3. To turn off the vibration alert, press and hold the scan/vibrate button again until
the
icon goes out.
The vibration alert feature only functions when CTCSS codes are assigned
to a channel.
Locking In Your Selection
To prevent the channel and code settings from accidentally being changed, you should
lock the buttons of your FRS radio. This will disable the L, L, wx/ctcss, and
scan/vibrate buttons.
1. Press and hold the light/lock button
for two seconds to lock the buttons.
The icon appears on the display
indicating the buttons are locked.
2. Press and hold the light/lock button again for two seconds to unlock the buttons.
Or turn the radio off and then on again to unlock the buttons.
12
The call/vox, on/off volume, PTT, MON, and light/lock buttons will
not be locked.
Call Tone Transmission
If you want to contact someone in your
party, press the call/vox button. ”CALL”
and the transmit icon appear on the LCD
for 2 seconds. Anyone on the same channel
and the same CTCSS code will be alerted
with your Call Tone.
Monitoring Weather Channels
Your radio has 7 preprogrammed weather channel frequencies, represented by numbers 1-7.
To listen to the weather channels in your area:
1. Press the wx/ctcss button. The radio
will begin scanning automatically.
The scan and
while scanning.
icon appear
2. Scanning stops when the radio finds an
active channel. It stays on the channel
until its transmission ends, and resumes
scanning after a 2 second delay.
3. To exit from this weather channel mode, press the wx/ctcss button again.
13
You can also select any one of the 7 channels manually.
1. Press the scan/vibrate button to stop scanning.
2. Use the up or down button to move to a higher or lower channel.
3. To resume scanning, press the scan/vibrate button again.
To change the channel continuously, press and hold the up or down
button for more than 1 second.
Silent Keypad
A tone sounds when any button is pressed. This is the default setting. This function may be
silenced if you wish. To silence the tones, press and hold the MON button while you turn
on the radio. If you want to hear the tones again, press and hold the MON button while
you turn on the radio. When the radio is turned off and then on again, the last selected
setting remains.
This function will also silence call tones and error tones.
LCD Backlight
The LCD display can be illuminated to assist your viewing. Press the light/lock button to
turn on the display backlight. The light goes off automatically after 5 seconds.
External Microphone and Speaker (Optional)
Available as an optional accessory. Use only an original Uniden speaker/microphone.
Use of any other speaker/microphone may void your warranty. To purchase your external
accessory, contact your local Uniden dealer or call Customer Service at (800)297-1023
Monday through Friday, 7:00 a.m. to 7:00 p.m. Central time.
14
Troubleshooting
Problem
Solution
No power
• Reposition or replace batteries.
• Make sure the PTT button is completely pressed
as you transmit.
Message not
transmitted
• Reposition or replace batteries.
Message not received • Confirm radios have the same channel and CTCSS
code setting.
• Make sure PTT is not inadvertently being pressed.
• Reposition or replace batteries.
• Obstructions, operating indoors and in vehicles may
interfere with communication. Change your
location.
• Be sure the volume is turned up.
Hearing other
• Confirm CTCSS code is set.
conversations or
noise on a channel
Limited talk range
• Shared channel or CTCSS may be in use.
Try another channel.
• Street/concrete structures, heavy foliage, and use
in buildings and in vehicles will decrease the range.
Check for clear line of sight to improve
transmission.
• Wearing the radio close to the body, such as in a
pocket or on a belt will decrease range. Change
the location of radio.
Heavy static or
interference
• Radios are too close. Radios must be at least 5 feet
apart. Increase your distance.
• Radios are too far apart.
Obstacles interfere with transmission. Talk range is
up to 2 miles in clear, unobstructed conditions.
If after trying these simple steps your unit still does not function properly, call
Uniden Customer Service at (800)297-1023 Monday through Friday, 7 a.m. to 7 p.m. CST.
15
Specifications
Description
Channels
14
Codes
Operating Frequency
Talk range
38 STANDARD CTCSS Tone
UHF - 462.550 to 467.725 MHz
Up to 2 Miles
Power Source
Transmit Power Out
Battery Life
3AA Alkaline Batteries (not supplied)
500m W
50 Hours typ.
Channel Frequency Chart (MHz)
Channel
Frequency
462.5625
462.5875
462.6125
462.6375
462.6625
Channel
Frequency
462.6875
462.7125
467.5625
467.5875
467.6125
Channel
11
12
13
14
Frequency
467.6375
467.6625
467.6875
467.7125
1
2
3
4
5
6
7
8
9
10
CTCSS Chart (Hz)
Channel
Frequency
Channel
14
15
16
17
18
19
20
21
22
23
24
25
Frequency
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
162.2
Channel
27
28
29
30
31
32
33
34
35
36
37
38
Frequency
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
1
2
3
4
5
6
7
8
9
10
11
12
13
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
26
16
WX Frequency Chart (MHz)
Channel
Frequency
162.550
162.400
162.475
162.425
162.450
162.500
162.525
1
2
3
4
5
6
7
memo
17
Appendix - FRS Radio Rules
FCC Part 95 Subpart B
(3) Aboard any vessel or aircraft registered
§95.191 (FRS Rule 1)
in the United States, with the permission of
the captain, that is within or over any area
of the world where radio services are
regulated by the FCC or upon or over
international waters;
Eligibility and responsibility.
(a) Unless you are a representative of a
foreign government, you are authorized by
this rule to operate an FCC certified FRS unit
in accordance with the rules in this subpart.
No license will be issued.
(4) Aboard any unregistered vessel or
aircraft owned or operated by a United
States citizen or company that is within or
over any area of the world where radio
services are regulated by the FCC or upon
or over international waters.
(b) You are responsible for all
communications that you make with the FRS
unit. You must share each channel with
other users. No channel is available for the
private or exclusive use of any user.
(5) You must operate the FRS unit only
according to any applicable treaty to
which the United States is a party. The
FCC will make public notice of any
such conditions.
§95.192 (FRS Rule 2)
Authorized locations.
(a) Provided that you comply with these
rules, you are authorized to operate an
FRS unit:
(b) [Reserved]
(c) [Reserved]
(1) Within or over any area of the world
where radio services are regulated by the
FCC (this area includes the fifty United
States and the District of Columbia, the
Commonwealth of Puerto Rico, the United
States Virgin Islands (50 islets and cays),
American Samoa (seven islands), the
Commonwealth of Northern Marianna
Islands, and Guam Island);
(d) Anyone intending to operate an FRS unit
on the islands of Puerto Rico, Desecheo,
Mona, Vieques, and Culebra in a manner that
could pose an interference threat to the
Arecibo Observatory shall notify the
Interference Office, Arecibo Observatory, Post
Office Box 995, Arecibo, Puerto Rico 00613,
in writing or electronically, of the location of
the unit. Operators may wish to consult
interference guidelines, which will be
(2) Within or over any other area of the
world, except within or over the territorial
limits of areas where radio services are
regulated by an agency of the United
States other than the FCC or any foreign
government (you are subject to its rules);
provided by Cornell University. Operators who
choose to transmit information electronically
should e-mail to: [email protected].
A-1
(1) The notification to the Interference
Office, Arecibo Observatory shall be made
45 days prior to commencing operation of
the unit. The notification shall state the
geographical coordinates of the unit.
(c) You must not use an FRS unit in
connection with any activity which is against
federal, state or local law.
(d) You must, at all times and on all
channels, give priority to emergency
communication messages concerning the
immediate safety of life or the immediate
protection of property.
(2) After receipt of such notifications, the
Commission will allow the Arecibo
Observatory a period of 20 days for
comments or objections. The operator will
be required to make reasonable efforts in
order to resolve or mitigate any potential
interference problem with the Arecibo
Observatory. If the Commission
determines that an operator has satisfied
its responsibility to make reasonable efforts
to protect the Observatory from
interference, the unit may be allowed
to operate.
(e) No FRS unit may be interconnected to the
public switched network.
§95.194 (FRS Rule 4)
FRS units.
(a) You may only use an FCC certified FRS
unit. (You can identify an FCC certified FRS
unit by the label placed on it by the
manufacturer.)
(b) You must not make, or have made, any
internal modification to an FRS unit. Any
internal modification cancels the FCC
certification and voids your authority to
operate the unit in the FRS.
§95.193 (FRS Rule 3)
Types of communications.
(a) You may use an FRS unit to conduct
two-way voice communications with another
person. You may use the FRS unit to
transmit one-way communications only to
establish communications with another
person, send an emergency message, provide
traveler assistance, make a voice page, or to
conduct a brief test.
(c) You may not attach any antenna, power
amplifier, or other apparatus to an FRS unit
that has not been FCC certified as part of that
FRS unit. There are no exceptions to this
rule and attaching any such apparatus to a
FRS unit cancels the FCC certification and
voids everyone's authority to operate the unit
in the FRS.
(b) The FRS unit may transmit tones to
make contact or to continue communications
with a particular FRS unit. If the tone is
audible (more than 300 Hertz), it must last
no longer than 15 seconds at one time. If the
tone is subaudible (300 Hertz or less), it may
be transmitted continuously only while you
are talking.
A-2
© 2000 Uniden America Corporation
All rights reserved • Printed in China
UTZZ01 875ZZ
Covered under one or more of the following U.S. patents:
4,398,304
4,627,100
5,199,109
5,471,660
5,530,296
4,409,688
4,841,302
5,408,692
5,483,684
5,574,995
4,455,679
4,888,815
5,428,826
5,548,832
5,577,076
4,461,036
4,932,074
5,438,688
5,551,071
5,598,430
4,521,915
4,947,456
5,448,256
5,642,424
5,600,223
4,597,104
5,014,348
5,465,402
5,710,992
|