Uniden Telephone BT 1007 User Manual

DECT1340 Series User's Guide

What's in the box?

DECT1340 base

and cordless

handset

AC adapter (PS-0035) Telephone cord

Battery

cover

Rechargeable

battery pack

(BT-1007)

x If any items are missing or damaged, contact our Customer Care Line

immediately. Never use damaged products!

x Need help? Get answers 24/7 at our website: www.uniden.com.

If You...

Contact Uniden’s...

Phone Number

817-858-2929 or

800-297-1023

have a question or problem Customer Care Line*

need a replacement part or

Parts Department*

an accessory

800-554-3988

need special assistance due

Accessibility Help Line

to a disability

800-874-9314

(voice or TTY)

* During regular business hours, Central Standard Time; see our website for detailed busi-

ness hours.

Important Safety Instrucꢀons!

When using your telephone equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and injury to

persons, including the following:

x This unit is NOT waterproof. DO NOT expose this unit to rain or moisture.

x Do not use this product near water, for example, near a bath tub, wash bowl,

kitchen sink or laundry tub, in a wet basement or near a swimming pool.

x Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

x Do not use the telephone to report a gas leak in the vicinity of the leak.

x Use only the power cord and batteries indicated in this manual. Do not

dispose of batteries in a fire. They may explode. Check with local codes for

possible special disposal instructions.

x Do not place the handset in any charging cradle without the battery installed

and the battery cover securely in place.

SAVE THESE INSTRUCTIONS!

CAUTION! Risk of explosion if battery is replaced by an incorrect type!

Dispose of used batteries according to the instructions. Do not open

or mutilate the battery. Disconnect the battery before shipping this

product.

For more details, see the Important Information section.

GETTING STARTED

Charging the Baꢁery

1. Unpack the handset, battery pack, and

battery cover. If you need to remove the

battery cover, press in on the notch and

slide the cover down and off.

2. Line up the battery connector with the jack

inside the handset. (The battery connector

will only fit one way.)

3. Push the connector in until it clicks into place; tug gently on the wires to

make sure the battery pack is securely connected.

4. Replace the battery cover and slide it into place.

USING YOUR PHONE

Basics

To...

Follow these steps…

make a call

answer a call

hang up

Press Talk and then dial the number.

Press Talk.

Press End or put the handset in the cradle.

Press Talk and then press rEdial.

redial a number

mute the microphone

during a call

Press MUTE. Press again to turn the microphone

back on.

While the phone is ringing, press MUTE or End.

(The handset must be off the cradle before the

phone starts ringing.)

mute the ringer for this

call only

Adjusꢀng the Ringer Tone and the Earpiece Volume

Change the

When

Follow these steps…

Press UP or down to cycle through the 2

the phone is ringer tones at low, medium, and high

ringer tone

in standby

volume; when you hear the tone and

volume combination you want to use, stop.

Press UP or down to select one of the 6

volume levels.

earpiece volume during a call

Using Call Waiꢀng

If you subscribe to Call Waiting service through your telephone company and a

call waiting tone sounds while you are on a call, press Flash to switch between

the current call and the waiting call; each time you switch, there is a short pause

before you’re connected to the other call.

Using Memory Dial

You can enter ten different phone numbers (up to 20 digits each) in the phone’s

dialing memory. Each memory dial entry is assigned to one of the number keys

(

9) on the twelve-key dial pad.

Storing numbers in memory dial

1. With the phone in standby, press MEMory. The Talk/baTT low light flashes.

2. Use the keypad to enter the phone number exactly as you would dial it.

x If you need the phone to wait before sending the next set of numbers, press

PaUsE to insert a two-second pause. Each pause counts as a digit.

x If you don’t press any keys for 30 seconds, the phone times out and returns

to standby.

3. Press MEMory again.

4. Press the number key (

9) you want to assign to this memory dial entry.

#^YW^ouhe^wn^illy^ho^eu^aras^as^cig^on^nfa^irmm^ae^tm^iooⁿr^ty^ond^eia^.l entry to a number key, the phone

automatically overwrites any previous entry assigned to that key.

Dialing a memory dial entry

1. When the phone is in standby, press Talk.

2. Press MEMory.

3. Press the number key assigned to the memory dial entry you want to use.

#If you press a number key with no assigned memory dial entry, the

handset beeps, and the phone will not dial.

Erasing a memory dial entry

1. With the phone in standby, press MEMory twice.

2. Press the number key assigned to the entry you want to erase. You will hear a

confirmation tone.

Chain dialing

If you often have to enter a code number during a call, you can use memory dial

to transmit the code number.

1. Store the code number (up to 20 digits) into memory dial just like a regular

entry.

2. Make your call normally. During a call, when you hear the prompt that tells

you to enter the number, press MEMory followed by the number key assigned

to the entry you want to use.

Finding the Handset

With the phone in standby, press Find on the base. The handset will beep for 1

minute or until you press Find again. You can also end the page by pressing any

key on the handset.

IMPORTANT INFORMATION

Solving Problems

If you have any trouble with your phone, try these simple steps first. If you need

help, call our Customer Care Line listed on the front cover.

If…

Try…

- Moving the handset closer to the base.

- Making sure the base is plugged in.

- Checking the telephone cord connection.

- Disconnecting the base AC adapter. Wait a few minutes,

then reconnect it.

I can’t make or

receive calls.

- Charging the battery for 15-20 hours.

- Moving the handset closer to the base.

- Charging the battery for 15-20 hours.

- Checking the battery connection.

The handset won’t

ring.

The handset is not

working.

I hear a beeping

during a call.

- The battery is getting low. Finish your conversation and

return the handset to the cradle as soon as possible.

Weak or Hard To Hear Audio

If a caller’s voice sounds weak or soft, the signal might be blocked by large

metal objects or walls; you might also be too far from the base, or the handset’s

battery may be weak.

x Try moving around while you’re on a call or moving closer to the base to see if

the sound gets louder.

x Make sure the handset’s battery is fully charged.

x Try adjusting the earpiece volume.

Noise or Staꢀc on the Line

Interference is the most common cause of noise or static on a cordless phone.

Here are some common sources of interference:

- electrical appliances, especially microwave ovens

- computer equipment, especially wireless LAN equipment and DSL modems

- radio-based wireless devices, such as room monitors, wireless controllers, or

wireless headphones or speakers

- fluorescent light fixtures (especially if giving off a buzzing noise)

- other services that use your phone line, like alarm systems, intercom systems,

or broadband Internet service

x Check nearby for one of the common interference sources.

x Try moving the handset and base away from a suspected source so the source is

not between the handset and the base, or turn off the source if possible.

x There is always more noise at the edges of the base’s range. If noise increases,

try moving closer to the base.

Installing a line ﬁlter or DSL ﬁlter

Sometimes, broadband Internet services that use the telephone line can

interfere with phones. One of these services−DSL−often causes static on

telephones. A DSL filter or telephone line filter usually solves this problem. The

technician who installed your DSL service might have left some filters for you; if

not, call your DSL provider or look in any electronics store.

Plug the DSL filter into the telephone wall jack and plug your phone’s base into

the filter. Make a test call to make sure the noise is gone.

Do you use a T-coil hearing aid?

If you have a hearing aid equipped with a telecoil (T-coil) feature, the interaction

between the hearing aid and digital cordless phones can cause noise in the

handset. If you have a T-coil hearing aid and you have problems with noise on

the line, try turning on T-coil mode.

1. In standby, press and hold Flash until you hear a confirmation tone.

2. Press

to turn the T-coil mode on. Press to turn the T-coil mode off.

Using T-coil mode can shorten the handset’s talk time; make sure to watch the

battery status and keep the battery charged.

#When the T-coil mode is on, the Talk/baTT low light flashes during a

call.

Liquid Damage

Moisture and liquid can damage your cordless phone.

x If the exterior housing of the handset or base is exposed to moisture or liquid,

wipe off the liquid, and use as normal.

x If moisture or liquid is inside the plastic housing (i.e. liquid can be heard in the

phone or liquid has entered the handset battery compartment or vent openings

on the base), follow these steps:

Handset

Base

1. Remove the battery cover and disconnect the 1. Disconnect the AC

battery.

adapter to cut off the

power.

2. Let dry for at least 3 days with the battery

disconnected and the cover off for ventilation. 2. Disconnect the telephone

3. After the handset dries, reconnect the battery

and replace the cover. Recharge the battery

fully (15-20 hours) before using.

cord.

3. Let dry for at least 3 days

before reconnecting.

CAUTION! DO NOT use a microwave oven to speed up the drying

process. This will cause permanent damage to the handset, base, and

the microwave oven.

AC Adapter and Baꢁery Informaꢀon

Use only the supplied AC adapter. Be sure

to use the proper adapter for the base.

Do not place the power cord where it

creates a trip hazard or where it could

become chafed and create a ﬁre or electri-

cal hazard.

Part number

Input voltage

Output voltage 8V AC @ 300mA

Part number

Capacity

PS-0035

120V AC, 60 Hz

adapter

BT-1007

500mAh, 2.4V DC

Baꢀery

pack

Do not place the unit in direct sunlight or

subject it to high temperatures.

Fully charged, the baꢀery should provide about 10 hours of talk ꢁme and about 7 days of standby

ꢁme. For best results, return the handset to the cradle aﬅer each call to keep it fully charged.

When the baꢀery gets too low, the handset shows a low baꢀery alert. If you hear a strange beep dur-

ing a call, check the display: if you see the low baꢀery alert, ﬁnish your conversaꢁon as quickly as pos-

sible and return the handset to the cradle. If the handset is in standby, none of the keys will operate.

With normal use, the baꢀery should last about one year. Replace the baꢀery when the talk ꢁme

becomes short even when the baꢀery is charged. To buy a replacement baꢀery, call the Parts

Department listed on the front cover.

Rechargeable Nickel-Cadmium baꢁery warning

This equipment contains a rechargeable Nickel-Cadmium (Ni-Cd) baꢀery.

Cadmium and Nickel are chemicals known to the state of California to cause cancer.

Do not short-circuit the baꢀery.

The rechargeable Ni-Cd baꢀeries contained in this equipment may explode if disposed of in a ﬁre.

Do not charge the baꢀery used in this equipment in any charger other than the one designed to charge

this baꢀery as speciﬁed in the owner's manual. Using another charger may damage the baꢀery or

cause it to explode.

As part of our commitment to protecꢁng our environment and conserving

natural resources, Uniden voluntarily parꢁcipates in an RBRC^®industry program

to collect and recycle used Ni-Cd baꢀeries within the United States. Please call

1-800-8-BATTERY for informaꢁon on Ni-Cd baꢀery recycling in your area.

(RBRC^®is a registered trademark of the Rechargeable Baꢀery Recycling Corporaꢁon.)

Rechargeable baꢁeries must be recycled or disposed of properly. Uniden works to reduce lead

content in PVC coated cords in our products and accessories.

Warning! The cords on this product and/or accessories contain lead, a chemical known to the

state of California to cause birth defects or other reproducꢀve harm. Wash hands aﬅer handling.

Compliance Informaꢀon

FCC Part 68 Informaꢀon

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.

On the boꢀom of this equipment is a label that contains, among other informaꢁon, a product

idenꢁﬁer in the format US: AAAEQ##TXXXX. If requested, this number must be provided to the

phone company.

An applicable Universal Service Order Codes (USOC) cerꢁﬁcaꢁon for the jacks used in this equip-

ment is provided (i.e., RJ11C) in the packaging with each piece of approved terminal equipment. A

plug and jack used to connect this equipment to the premises wiring and telephone network must

comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant

telephone cord and modular plug is provided with this product. It is designed to be connected to a

compaꢁble modular jack that is also compliant. See installaꢁon instrucꢁons for details.

The REN is used to determine the number of devices that may be connected to a phone line.

Excessive RENs on a phone line may result in devices not ringing in response to an incoming

call. In most but not all areas, the sum of RENs should not exceed ﬁve (5.0). To be certain of the

number of devices that may be connected to a line, as determined by the total RENs, contact the

telephone provider. The REN for this product is part of the product idenꢁﬁer that has the format

US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a

REN of 0.3).

If this equipment causes harm to the telephone network, the telephone company will noꢁfy you

in advance that temporary disconꢁnuance of service may be required. But if advance noꢁce isn't

pracꢁcal, the telephone company will noꢁfy the customer as soon as possible. Also, you will be

advised of your right to ﬁle a complaint with the FCC if you believe it is necessary. The telephone

company may make changes in its faciliꢁes, equipment, operaꢁons or procedures that could aﬀect

the operaꢁon of the equipment. If this happens the telephone company will provide advance

noꢁce in order for you to make necessary modiﬁcaꢁons to maintain uninterrupted service.

Please follow instrucꢁons for repairing, if any (e.g. baꢀery replacement secꢁon); otherwise do not

subsꢁtute or repair any parts of the device except as speciﬁed in this manual. Connecꢁon to party

line service is subject to state tariﬀs. Contact the state public uꢁlity commission, public service

commission or corporaꢁon commission for informaꢁon. This equipment is hearing aid compaꢁble.

If you experience trouble with this equipment, contact the manufacturer (see the cover of this

manual for contact informaꢁon) or an authorized agent. If the equipment is causing harm to the

telephone network, the telephone company may request that you disconnect the equipment unꢁl

the problem is resolved.

If your home has wired alarm equipment connected to a phone line, be sure that installing the

system does not disable your alarm equipment. If you have quesꢁons about what will disable alarm

equipment, contact your telephone company or a qualiﬁed installer.

Any changes or modiﬁcaꢁons to this product not expressly approved by the manufacturer or other

party responsible for compliance could void your authority to operate this product.

NOTICE: According to telephone company reports, AC electrical surges, typically resulꢁng from

lightning strikes, are very destrucꢁve to telephone equipment connected to AC power sources. To

minimize damage from these types of surges, a surge arrestor is recommended.

FCC Part 15 Informaꢀon

This device complies with part 15 of the FCC rules. Operaꢁon is subject to the following two

condiꢁons: (1) This device may not cause harmful interference, and (2) This device must accept

any interference received, including interference that may cause undesired operaꢁon. Privacy of

communicaꢁons may not be ensured when using this phone.

FCC PART 15.105(b): Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protecꢁon against harmful interference in a residenꢁal installaꢁon. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instrucꢁons, may cause harmful interference to radio communicaꢁons. However, there

is no guarantee that interference will not occur in a parꢁcular installaꢁon. If this equipment does

cause harmful interference to radio or television recepꢁon, which can be determined by turning

the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna.

Increase the separaꢁon between the equipment and receiver.

Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC RF Exposure Informaꢀon

This product complies with FCC radiaꢁon exposure limits under the following condiꢁons:

The base must be placed to allow a minimum of 20 cm (8 inches) between the antenna and all

persons during normal operaꢁon.

The base must not be collocated or operated in conjuncꢁon with any other antenna or transmiꢀer.

The handset is designed for body-worn operaꢁon and meets FCC RF exposure guidelines when

used with any belt clip, carrying case, or other accessory supplied with this product. (All necessary

accessories are included in the package; any addiꢁonal or opꢁonal accessories are not required for

compliance with the guidelines.) Third party accessories (unless approved by the manufacturer)

should be avoided as these might not comply with FCC RF exposure guidelines.

Industry Canada (I.C.) Noꢀce

Terminal equipment

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical

Speciﬁcaꢁons. This is conﬁrmed by the registraꢁon number. The abbreviaꢁon IC before the

registraꢁon number signiﬁes that registraꢁon was performed based on a Declaraꢁon of

Conformity indicaꢁng that Industry Canada technical speciﬁcaꢁons were met. It does not imply

that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the

equipment itself. The REN assigned to each terminal equipment provides an indicaꢁon of the

maximum number of terminals allowed to be connected to a telephone interface. The termina-

ꢁon on an interface may consist of any combinaꢁon of devices subject only to the requirement

that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Radio equipment

The term IC before the radio cerꢁﬁcaꢁon number only signiﬁes that Industry Canada technical

speciﬁcaꢁons were met. Operaꢁon is subject to the following two condiꢁons: (1) this device

may not cause interference, and (2) this device must accept any interference, including interfer-

ence that may cause undesired operaꢁon of the device. "Privacy of communicaꢁons may not be

ensured when using this telephone."

One-Year Limited Warranty

Evidence of original purchase is required for warranty service.

WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden")

ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this

Uniden Product to be free from defects in materials and craﬅsmanship with only the limitaꢁons

or exclusions set out below.

WARRANTY DURATION: This warranty to the original user shall terminate and be of no further

eﬀect 12 months aﬅer the date of original retail sale. The warranty is invalid if the Product is (A)

damaged or not maintained as reasonable or necessary, (B) modiﬁed, altered, or used as part of

any conversion kits, subassemblies, or any conﬁguraꢁons not sold by Uniden, (C) improperly in-

stalled, (D) serviced or repaired by someone other than an authorized Uniden service center for

a defect or malfuncꢁon covered by this warranty, (E) used in any conjuncꢁon with equipment or

parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by

anyone other than as detailed by the owner's manual for this product.

STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at

any ꢁme while this warranty is in eﬀect, warrantor will either, at its opꢁon, repair or replace the

defecꢁve unit and return it to you without charge for parts, service, or any other cost (except

shipping and handling) incurred by warrantor or its representaꢁves in connecꢁon with the per-

formance of this warranty. Warrantor, at its opꢁon, may replace the unit with a new or refur-

bished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY

PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES

OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF

LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR

THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some

states do not allow this exclusion or limitaꢁon of incidental or consequenꢁal damages so the

above limitaꢁon or exclusion may not apply to you.

LEGAL REMEDIES: This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state. This warranty is void outside the United States of America

and Canada.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, aﬅer following the instrucꢁons

in the owner's manual you are certain that the Product is defecꢁve, pack the Product carefully

(preferably in its original packaging). Disconnect the baꢀery from the Product and separately

secure the baꢀery in its own separate packaging within the shipping carton. The Product should

include all parts and accessories originally packaged with the Product. Include evidence of

original purchase and a note describing the defect that has caused you to return it. The Product

should be shipped freight prepaid, by traceable means, to warrantor at:

Uniden America Service

4700 Amon Carter Blvd.

Fort Worth, TX 76155

As an Energy Star® Partner, Uniden has determined that this product meets

the Energy Star® guidelines for energy eﬃciency. Energy Star® is a

U.S. registered mark.

Uniden® is a registered trademark of Uniden America Corporaꢁon.

The pictures in this manual are for example only. Your phone may not look exactly like the pictures.

May be covered under one or more of the following U.S. patents:

5,491,745 5,533,010 5,574,727 5,581,598 5,606,598 5,650,790 5,660,269 5,663,981

5,671,248 5,717,312 5,732,355 5,754,407 5,758,289 5,768,345 5,787,356 5,794,152

5,801,466 5,825,161 5,864,619 5,893,034 5,912,968 5,915,227 5,929,598 5,930,720

5,960,358 5,987,330 6,044,281 6,070,082 6,076,052 6,125,277 6,253,088 6,321,068

6,418,209 6,618,015 6,714,630 6,782,098 6,788,920 6,788,953 6,839,550 6,889,184

6,901,271 6,907,094 6,914,940 6,953,118 7,023,176 7,030,819 7,146,160 7,203,307

7,206,403 7,310,398 7,460,663

Other patents pending.

Ft. Worth, Texas

Printed in Vietnam

UNZZ01181ZZ(0)

Technicolor Thomson DVD Recorder DMR EH80V User Manual
Technika Clothes Dryer T50DM User Manual
Toshiba Blu ray Player BDX4300KU User Manual
Transcend Information Camera Accessories TS1GRMMC4 User Manual
Turbo Air Refrigerator TSF 23SD User Manual
Ultra Start Remote Starter 15xx User Manual
Universal Remote Control Universal Remote UR5U 8700L IP User Manual
Vornado Electric Steamer Essential Fabric Steamer User Manual
Wagner SprayTech Pressure Washer 558025 User Manual
Waste King Water Dispenser Hot Water Dispenser User Manual