User’s
Guide
Model 1380 Speakerphone Telephone
with Digital Answerer and Caller ID
on Call Waiting
likely give you adequate notice to allow you to maintain uninterrupted service.
Notice must be given to the telephone company upon termination of your telephone from your line.
REN Number
On the bottom of this equipment is a label indicating, among other information, the Ringer
Equivalence Number (REN) for the equipment.
The REN is useful in determining the number of devices you may connect to your telephone line and
still have all of these devices ring when your telephone number is called. In most (but not all) areas,
the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the
number of devices you may connect to your line as determined by the REN, you should contact your
local telephone company.
REN Number is located on the cabinet bottom.
Hearing Aid Compatibility
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensing
Licensed under US Patent 6,427,009.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body. This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
3
Table of Contents
Important Information ..................ꢀ
Interference Information ..............ꢀ
Telephone Network Information..ꢀ
REN Number .................................3
Hearing Aid Compatibility............3
Licensing.......................................3
Receiving a Phone Call....................13
Placing a Phone Call........................13
Switching between Speaker and
Handset ...................................13
Temporary Tone Dialing ...................13
Flash ................................................14
Redial...............................................14
Mute .................................................14
FCC RF Radiation Exposure
Statement...................................3
Telephone Set Up .......................15
Setting the Rings to Answer.............15
Setting the Incoming Message or
Introduction...................................6
Before You Begin..........................6
Parts Checklist ...................................6
Telephone Jack Requirements...........6
Memo Length ..............................16
Setting the Recording Quality .........16
Setting the Security Code ................17
Setting the Display Contrast.............17
Setting Your Local Area Code..........18
Setting the Dialing Mode..................18
Setting Day of Week ........................18
Setting the Time and Date................19
Setting the Language.......................20
Message Volume..............................20
Ringer Volume..................................20
Speakerphone Volume.....................21
Important Installation
Information.................................7
Base Layout..................................8
Installing the Phone .....................9
Desktop Installation............................9
Wall Mounting the Phone.................10
Important Instructions for Moving the
Answerer ..................................... 11
Answering System Setup ..........11
Recording the Outgoing
Announcement ............................ 11
Reviewing the Announcement..........12
Caller ID Features.......................ꢀꢀ
Summary Screen .............................22
Caller ID with Call Waiting................23
Receiving and Storing Calls.............23
Reviewing Call Records...................23
Deleting CID Records ......................24
Dialing Back .....................................24
Telephone Operation..................1ꢀ
Using the Speakerphone..................12
Speakerphone Location................12
Speakerphone Use.......................12
ꢁ
Table of Contents
If You Programmed Your Local Area
Code ...........................................24
If You Did Not Program Your Local
Answering System Operation ...3ꢀ
Call Answering .................................32
Auto Disconnect...............................32
Playing Messages............................33
Erase Messages ..............................33
Leaving a Memo...............................34
Memory Full .....................................34
Area Code ..................................25
Memory........................................ꢀ6
Storing a Number in Memory ..........26
Storing a Redial Number to Memory 27
Erasing a Stored Number.................28
Remote Access ................................34
Copying Caller ID Memories to User
Remote Access Commands .........35
Memory .......................................28
Inserting a Pause in the Dialing
Sequence ....................................29
Changing a Stored Number .............29
Message Indicators....................36
Troubleshooting Guide ..............37
General Product Care.................39
Causes of Poor Reception.........ꢁ0
Warranty......................................ꢁ1
Index ............................................ꢁꢀ
Dialing a Number Stored in Memory
While On-hook.............................29
Dialing a Number Stored in Memory 29
Reviewing Stored Numbers .............30
Chain Dialing from Memory..............31
5
Introduction
CAUTION: When using telephone equipment, there are
basic safety instructions that should always be followed.
Refer to the IMPORTANT SAFETY INSTRUCTIONS provided
with this product and save them for future reference.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
DC power
adaptor
Base
Handset
Coiled
cord
Line cord
Mounting
Telephone Jack Requibrreacmkeet nts
Wall plate
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in
Telephone
line jack
your home. If you don’t have a modular jack, call your local
phone company to find out how to get one installed.
6
Important Installation Information
• Never install telephone wiring during a lightning storm.
• Never touch non-insulated telephone wires or terminals, unless the telephone
line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
7
Base Layout
Quick dial/emergency repeat
memory (buttons) (button)
speaker
(button)
display
mute (button)
Hook
switch
VOL+/- (buttons)
ringer volume
switch
skip (button)
PLAY/STOP
(button)
message
speed (button)
delete (button)
announce (button)
memo (button)
ans on/off
(button)
* tone
(button)
store (button)
menu (button)
redial/pause
(button)
Microphone
flash/exit (button)
dial (button)
8
Installing the Phone
Desktop Installation
CAUTION: To reduce risk of personal injury, fire, or
damage use only the 5-ꢀ78ꢁ power adaptor listed in
the user’s guide. This power adaptor is intended to be
correctly orientated in a vertical or floor mount position.
1. Plug the coiled cord into the handset. Plug the other end into the jack on the
side of the base.
2. Place the handset in
the base.
3. Plug the telephone
line cord into the LINE
jack on the back of the
phone. Plug the other
end into a wall jack.
4. Connect the small end
of the power adaptor
into the POWER 9V DC
jack on the back of the answerer. Plug the other end into an AC power outlet.
The unit announces “Press menu key to set up the unit”. The unit is ready
for setup or to answer calls with the default greeting and settings.
Note: The phone automatically defaults to touch-tone dialing. To
change to pulse (rotary) dialing, see “Setting the Dialing Mode.”
If you don’t know which type of service you have, check with the
phone company.
Note: The unit is properly installed if you pick up the handset and
hear the dial tone. Otherwise, recheck all the installation steps.
Wall Mounting the Phone
9
Your speakerphone can also be mounted on a wall plate (not included).
Note: To prevent the handset from falling out of the cradle while the
phone is hanging on the wall, you must switch both the handset
hook and the desk stand to their wall-mount positions.
1. On the front of the base, pull the handset hook out of the slot. Rotate hook
180 degrees and flip it from front to back. Slide it
back into the slot.
2. Turn the base over. Press in on the tabs and
remove the desk stand from the back of the base.
3. Rotate the stand 180 degrees, and insert
the hooks marked WALL into the notches
marked WALL. Press in on the tabs and
snap the stand into place.
4. Connect the telephone line cord to the
wall jack and the phone. If desired, wrap
any excess cord around the cord hooks as
shown.
5. Place the mounting slots over the pins on
the wall plate, and slide
the base down to lock
it into place.
Important
Instructions
for Moving the
10
Answerer:
To move the answerer to a different location in the house, follow these
instructions:
1. Disconnect the phone line.
2. Go to the electrical outlet and unplug the power adaptor.
3. Move the unit and phone line to the desired location.
4. Plug in the power adaptor into an electrical outlet.
5. The display shows that the messages have not been erased.
6. Connect the phone line.
7. Reset the time/date settings or wait for the next call to set them automatically.
Answering System Setup
Recording the Outgoing Announcement
Before using your new answerer, you should record a greeting (the
announcement callers hear when your answering system answers a call). If you
don’t record a greeting, callers hear a default greeting which says, “We are not
available to take your call. Please leave a message. Thank you for calling.”
When recording the greeting you should be about 6 inches from the unit.
Eliminate as much background noise as possible.
1. Prepare your greeting.
Sample Greeting: “Hi, this is (use your name here). I can’t answer the phone
right now, so please leave your name, number, and a brief message after the
tone, and I’ll get back to you. Thanks for calling.”
2. Hold down the ANNOUNCE button. The unit announces “Record
announcement after the tone,” and the screen displays TO RECORD. After
the tone, you can record a 1 minute greeting (OGA) on the unit.
3. Release ANNOUNCE when you finish.
• To review the greeting, press and release ANNOUNCE. The unit plays back
your greeting automatically.
11
• To return to the answerer’s default greeting after you’ve recorded one, press
ANNOUNCE and release it when you hear the tone, or press and hold
DELETE when the greeting is playing.
Reviewing the Announcement
Press and release the ANNOUNCE button to review your outgoing announcement.
Telephone Operation
Using the Speakerphone
Speakerphone Location
For best speakerphone performance, avoid the following:
• Areas with high background noise. (The microphone might pick up these
sounds and prevent the speakerphone from going into the receiving mode
when you finish talking.)
• Surfaces affected by vibration.
• Recessed areas such as in a corner, under a cupboard, or next to a cabinet,
which can generate an echo effect.
Speakerphone Use
Note the following guidelines when using the speakerphone:
• The speakerphone works similar to a two-way radio in that you can only listen
or talk at one time.
• Stay reasonably close to the phone so that you can be clearly heard by the
person to whom you are talking.
• You can adjust the speaker volume by pressing the VOL (+ or -) buttons.
• The speakerphone indicator comes on when the speakerphone is in use.
1ꢀ
Receiving a Phone Call
1. When the phone rings, the speakerphone indicator blinks and the caller’s
information, if any, will be shown on the display panel. Lift the handset or press
the SPEAKER button to connect your phone call.
2. You can adjust the volume of the caller’s voice by pressing the VOL (+ or -)
buttons.
Placing a Phone Call
1. Lift the handset or press the SPEAKER button and wait for a dial tone.
2. Dial the telephone number you wish to call.
3. User can also dial the number on the keypad first, then press the SPEAKER
button to dial out. In case of a mistake in entering the number, press DELETE
to erase the last digit.
4. You can adjust the volume of the caller’s voice by pressing the VOL (+ or -)
buttons.
Switching between Speaker and Handset
You can switch between speakerphone and handset while the phone is dialing a
number, or anytime during a conversation.
• Speaker to Handset — Pick up the handset.
• Handset to Speaker — Press SPEAKER, then hang up handset.
Temporary Tone Dialing
If you have pulse service, you can temporarily change from pulse to tone service.
After dialing the telephone number, press and release the TONE (*) button on
the telephone. This allows access to phone services that require a tone, such
as banking and long-distance services. After you hang up the handset, the
telephone automatically returns to pulse service.
13
Flash
Press the FLASH button instead of using the hook switch to activate customer
calling services such as call waiting or call transfer, which are provided by your
local phone company.
Redial
Redial the last number you called by pressing the REDIAL button after you get a
dial tone.
Note: The REDIAL feature holds in memory the last phone number
you dialed (as many as 3ꢀ digits). If you pressed any numbers after
dialing the phone number, (for example, when accessing a voice-
menu system) those numbers also are redialed.
IMPORTANT: In the event of a power outage, your phone will still
be able to make and receive calls, however, the speakerphone and
answerer will not be operational.
Mute
1. Press the MUTE button to mute a call, the MUTE indicator will light up. You
will still be able to hear the calling party but they will not be able to hear you
speaking.
2. Press the MUTE button again to unmute the call.
1ꢁ
Telephone Set Up
You can customize the following settings to suit your needs.
Rings to Answer Selects the number of rings
Default Settings
before the unit answers.
Rings to Answer
Message Length
ꢁ
ꢀ minute
Standard
1 ꢀ 3
Message Length Sets the length of time allowed
Recording Quality
Security Code
Display Contrast
Local Area Code
Dialing
for incoming messages.
3
Recording Quality Sets the recording quality
between standard (STD) and
long play (LONG).
– – –
Tone
Day
Sunday
1ꢀ a.m. 1/01
English
Time/Date
Remote Access
Set your 3-digit code used for
remote access to the unit.
Language
Display Contrast Selects the display contrast.
Local Area Code Sets your local area code for Dial Back.
Tone/pulse Dialing Sets the phone for tone or pulse dialing.
Set Day
Sets the day.
Time/Date
Language
Sets the time and date.
Selects English, French or Spanish.
Setting the Rings to Answer
This setting allows you to set the number of rings before the unit answers a call.
You can choose from 2-8 or Toll Saver (see “Toll Saver.”)
1. Press and release the MENU button. The screen displays RING TO ANSWER.
The unit announces, Setup Menu. Use SKIP to change setting. Press MENU
to save a setting.
2. Use SKIP or REPEAT for the desired setting (2-8, Toll Saver).
3. When finished, press MENU to confirm.
Note: To skip to the next setting, press MENU. To exit setup, press EXIT.
15
Toll Saver
Toll Saver can save you the cost of a call when you access your messages
from another phone:
• If you have new messages, the unit answers after the 3rd ring.
• If you have no new messages, the unit answers after the 5th ring.
You can hang up after the 3rd ring and save the pay telephone or long distance
charge.
Setting the Incoming Message or Memo Length
This setting allows you to set the maximum length of time allowed for a single
incoming message or memo. You can choose from 1 minute to 4 minutes.
1. Press and release the MENU button until the screen displays MESSAGE
LENGTH.
2. Use SKIP or REPEAT for the desired setting.
3. When finished, press MENU to confirm.
Note: To skip to the next setting, press MENU. To exit setup, press
EXIT.
Setting the Recording Quality
This setting allows you to set the recording quality between standard (STD) and
long play (LONG). Long play will give more recording time than standard.
1. Press and release the MENU button until the screen displays REC:4STD
LONG.
2. Use SKIP or REPEAT or select the desired setting.
3. Press MENU to confirm setting and go to next setting.
16
Setting the Security Code
This feature allows you to change the factory default remote access code used
for remote access to your answerer. The default code is 123.
1. Press and release the MENU button until the screen displays REMOTE
ACCESS.
2. The left-most digit, or a (_) sign flashes indicating the unit is ready to accept
the security code entry.
3. Use the keypad number to set the 3-digit security code in one step.
4. After the 3rd and last digit is entered, press the MENU button to store the
security code and go to the next setting.
Note: To skip to the next setting, press MENU. To exit setup, press
EXIT.
Note: If you make a mistake, you can use SKIP or REPEAT to move
between 1st to 3rd digit and input number from keypad again.
Setting the Display Contrast
This setting allows you to adjust the display contrast for easier readability.
1. Press and release the MENU button until the screen displays CONTRAST.
2. Use SKIP or REPEAT to select the desired setting (1-5).
3. When finished, press MENU to confirm and go to the next setting.
Note: To skip to the next setting, press MENU. To exit setup, press EXIT.
17
Setting Your Local Area Code
1. Press and release the MENU button until the screen displays LOCAL AREA
CODE.
2. The left-most digit, or a (_) sign flashes indicating the unit is ready to accept
the area code entry.
3. Press the keypad number to set the 3-digit local area code in one step.
4. After the 3rd and last digit are entered, press the MENU button to store the
area code and go to the next setting.
Note: If you make a mistake, you can use SKIP or REPEAT to move
between 1st to 3rd digit and input the number from the keypad again.
Note: To skip to the next setting, press MENU. To exit setup, press EXIT.
Setting the Dialing Mode
This adjustment allows you to select tone (touch-tone) or pulse (rotary) mode
dialing. The phone is automatically set for touch-tone use.
1. Press and release the MENU button until the screen displays 4TONE PULSE.
“4” indicates which set up the unit is currently in.
2. Use SKIP or REPEAT for the desired setting.
3. When finished, press MENU to confirm.
Note: To skip to the next setting, press MENU. To exit setup, press EXIT.
Setting Day of Week
This setting allows you to set day of week .
1. Press and release the MENU button until the screen displays SET DAY.
2. Use SKIP and REPEAT for the desired setting .
3. Press MENU to confirm and go to the next setting.
18
Setting the Time and Date
Note: If you have subscribed to the Caller ID display feature from
your telephone company, the telephone company sends the time and
date with the Caller ID information. The unit automatically sets the
time and date when the first call is received.
Hour
1. Press and release the MENU button until the screen displays SET TIME/
DATE.
2. The hour digits flashing indicates that the unit is ready to accept entry. Use the
keypad numbers to enter a two digit number to set the hour.
3. When finished, the cursor moves to the Minute field. Now you’re ready to enter
the minutes.
Minutes
1. Use the keypad numbers to enter a two digit number to set the minutes.
2. When finished, the cursor moves to the AM or PM field. Now you’re ready to
enter the time of day, AM or PM.
AM/PM
1. Press “*” on the keypad for AM and press “#” for PM to set the time of day.
2. When finished, the cursor moves to the Month field. Now you’re ready to enter
the month.
Month
1. Use the keypad to enter two digit numbers to set the month.
2. When finished, the cursor moves to the Date field. Now you’re ready to enter
the day.
19
Date
1. Use the keypad to enter two digit numbers to set the date.
2. When finished, press MENU to confirm.
TIP: For example, to enter 8:09 a.m. 7/ꢁ:
1. Press 08.
2. Press 09.
3. Press * (for a.m.).
4. Press 07.
5. Press 04.
6. Press MENU.
Note: To skip to next setting, press SKIP. To exit setup, press EXIT.
Setting the Language
This setting allows you to listen to voice prompts and view Caller ID prompt
messages in English, French or Spanish.
1. Press and release the MENU button until the screen displays > ENG FRA
ESP.
“>” indicates which set up the unit is currently in.
2. Use SKIP or REPEAT for the desired setting.
3. When finished, press MENU to confirm.
Note: To skip to the next setting press MENU. To exit setup, press EXIT.
Message Volume
Use the VOL (+ or -) buttons to adjust the volume when playing back messages
and while reviewing or changing the setting.
Ringer Volume
Use the switch at the side of the unit to adjust the loudness of the ringer.
ꢀ0
Handset Volume
Use the VOL (+ or -) buttons to adjust the handset listening volume while it is in
use.
Speakerphone Volume
Use the VOL (+ or -) buttons to adjust the speakerphone listening volume while it
is in use.
ꢀ1
Caller ID Features
IMPORTANT: In order to use this unit’s Caller ID features, you must
subscribe to either the standard Name/Number Caller ID Service or
Call Waiting Caller ID Service. To know who is calling while you are
on the phone, you must subscribe to Call Waiting Caller ID Service.
This unit receives and displays CID information transmitted by your local
telephone company. This information can include the phone number, date and
time; or the name, phone number, and date and time.
Summary Screen
The summary screen shows the current time, current date and number of new
calls to be reviewed. It is displayed until any button is pressed. Within 10 seconds
of receiving a new call, the summary screen is displayed.
Call Waiting Indicator
Message waiting
Date
Caller Status; NEW or
REPEAT
Time
CID Record number
CID phone number
CID name
ꢀꢀ
Caller ID with Call Waiting
Provided you subscribe to Call Waiting Caller ID service from your phone
company; if you receive an incoming call and you are already on the phone, a
beep indicates the presence of a Call Waiting call on the line. Only the handset
that is in use at the time of the call will display and store the Call Waiting Caller
ID information.
• When you hear the call waiting beep in the handset receiver, press the FLASH/
EXIT button to put the current call on hold and answer the incoming call. Press
FLASH/EXIT again to return to the original call.
Receiving and Storing Calls
The unit receives and displays information transmitted by your local phone
company. This information can include the phone number, date, and time; or the
name, phone number, date, and time. The unit can store up to 60 CID memories
for later review. When the Caller ID memory is full, a new call automatically
replaces the oldest call in memory. NEW appears in the display for calls received
that have not been reviewed. REPT appears in the display for calls received
more than once which have not been reviewed.
Reviewing Call Records
Use either the SKIP or REPEAT button to review your Caller ID records.
• Press REPEAT to scroll through the call records from the most recent to the
oldest.
• Press SKIP to scroll through the call records from the oldest to the newest.
• When all of the messages have been viewed, the screen displays START/
END.
• If there are new calls, they will be displayed first.
• If there are only old calls, all the calls will be reviewed.
ꢀ3
Deleting CID Records
• To delete the record shown in the display, press the DELETE button once.
• To delete all records while reviewing, press and hold the DELETE button for
about three seconds. The screen displays DELETE ALL?. Press DELETE
again to complete.
Dialing Back
When reviewing Caller ID records, you can dial back the numbers on the display
by pressing the dial button.
Note: If PICKUP PHONE shows in the display, no other changes to
the number can be made. The information sent from the telephone
company is known to be a valid number for dialing back (used only
in very limited areas). Once you pickup the phone, the number is
automatically dialed.
If You Programmed Your Local Area Code
1. Use the SKIP or REPEAT buttons to display the number you want to dial.
2. Press the DIAL button.
• If you see a number with seven digits (i.e. 555-1234), then the call is from within
your area code. However, this does not guarantee the call is a local call.
• If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from
within your area code.
Note: A timer (10 seconds on-hook and 3 seconds off-hook) located
in the upper right side of the display will start, letting you know how
much time is left until the unit returns to the Summary Screen.
ꢀꢁ
3. If you are at on-hook and PICKUP or ADJ displays, you can adjust the phone
number format by pressing the DIAL button. If the phone is off-hook and
ADJUST shows in the display, you can adjust the phone number format by
pressing the DIAL button. For example, sometimes a 7-digit local number
cannot be dialed because it requires a 10-digit or 11-digit format. Press the
DIAL button repeatedly to scroll through the 7, 10, and 11-digit numbers.
7-digits:
7-digit telephone number (i.e. 555-5555)
10-digits: 3-digit area code + 7-digit telephone number (i.e. 425-555-5555)
11-digits: long distance code 1 + 3-digit area code + 7-digit telephone
number (i.e. 1-425-555-5555)
4. To dial the displayed number, and the phone is on-hook, pick up the handset
or press the SPEAKER button before the timer reaches 0. If the phone is off-
hook, wait until the time reaches 0. The screen displays NOW DIALING and
the number is dialed.
If You Did Not Program Your Local Area Code
1. Use the SKIP or REPEAT buttons to display the number you want to dial. You
will only see 10-digit numbers (i.e. 234- 555-1234).
2. See Steps 2 through 4 in the previous section to complete the dialback
process.
ꢀ5
Memory
You may store up to 13 numbers in memory for quick dialing – 3 in the Quick
Dial buttons (A, B, and C) and 10 in the keypad numbers (0-9). Each memory
location can store number up to 32 digits.
Storing a Number in Memory
1. Press the STORE button. The screen displays LOCATION?.
2. Press the desired memory location (0-9, A, B, C).
Note: You may select memory locations by pressing SKIP or REPEAT
(< or >) to scroll through the memory locations or press the 0 - 9, A,
B, C.
3. Press the STORE button again to confirm the memory location.
Note: If necessary, to erase existing memories, or if you make a
mistake, use the DELETE button.
4. Use the number keys to enter the telephone number (up to 32 digits) and
press the STORE button to save. (The unit will not dial a phone number in this
mode.) The cursor automatically moves to the text line for name entry.
5. Use the number keys to enter the name of the person associated with the
telephone number you just entered (up to 12 characters). More than one letter
is stored in each of the number keys. For example, to enter the name BILL
SMITH, press the “2” key twice for the letter B. Press the “4” key 3 times for the
letter I. Press the “5” key 3 times for the letter L.
Note: The flashing cursor automatically moves to the next position
or you may press the SKIP or REPEAT buttons to move the cursor
to the next position.
Press the “5” key 3 times for the second letter L. Press the SKIP button to
insert a space, and press the “7” key 4 times for the letter S. Press the “6” key
once for the letter M. Press the “4” key 3 times for the letter I. Press the “8” key
for the letter T. Press the “4” key twice for the letter H.
ꢀ6
7. To enter another name and number in a different memory location, return to
Step 1 and repeat the process.
Storing a Redial Number to Memory
1. Press the REDIAL button and the screen displays the number.
2. Press the STORE button. The screen displays LOCATION?.
3. Press the desired memory location (0-9, A, B , C ).
4. Press the STORE button again to confirm the memory location.
5. Press the STORE button again to save and you may now enter the contact
name.
6. Use the number keys to enter the name of the person associated with the
telephone number you just entered. More than one letter is stored in each of
the number keys. For example, to enter the name BILL SMITH, press the “2”
key twice for the letter B. Press the “4” key 3 times for the letter I. Press the “5”
key 3 times for the letter L.
Note: The flashing cursor automatically moves to the next position
or you may press the REPEAT or SKIP buttons to move the cursor to
the next position.
7. Press the “5” key 3 times for the second letter L. Press the SKIP to insert a
space. And press the “7” key 4 times for the letter S. Press the “6” key once for
the letter M. Press the “4” key 3 times for the letter I. Press the “8” key for the
letter T. Press the “4“ key twice for the letter H.
8. Press the STORE button to confirm.
ꢀ7
Erasing a Stored Number
1. Press the STORE button.
2. Press the memory location (0-9, A, B, C) to be erased.
3. Press the DELETE button.
Copying Caller ID Memories to User Memory
1. Press the SKIP or REPEAT buttons to view the caller number and name you
want to copy.
2. Press the DIAL button to change the format (11 or 10 or 7 digits number
format) as desired.
3. Press the STORE button.
4. Press the memory location (0-9, A, B, C). The number flashes if there is a
number already stored in the memory location.
5. Press the STORE button to enter the edit mode, and then press the STORE
button again to edit the name.
Note: You may select a different memory location by pressing the
SKIP or REPEAT button to scroll through the memories or press a
number key (0-9, A, B, C).
6. Press the STORE button to confirm and save.
Note: If the name you want to enter is longer than 1ꢀ characters, only
the first 12 characters will be copied into memory.
ꢀ8
Inserting a Pause in the Dialing Sequence
Press the REDIAL/PAUSE button to insert a delay in the dialing sequence of
a stored telephone number when a pause is needed to wait for a dial tone (for
example after you dial 9 for an outside line, or to wait for a computer access
tone). Each pause is represented as “P” on the display and counts as 1 digit in
the dialing sequence.
Changing a Stored Number
Repeat the storage sequence under “Storing A Name and Number in Memory”,
and use the DELETE button to delete the old number before entering the new
number.
Dialing a Number Stored in Memory While On-
hook
1. Press the DIAL button.
2. To select a memory, press any number key (0-9, A, B, C). The number in that
memory location displays.
Note: You may select a different memory location by pressing the
SKIP or REPEAT button to scroll through the memories or press a
number key (0-9, A, B, C).
3. Press the SPEAKER button, or pick up the handset to dial the displayed
number.
Dialing a Number Stored in Memory
1. Lift the handset, or press the SPEAKER button.
2. Press the DIAL button then press a memory location button.
ꢀ9
Reviewing Stored Numbers
1. Press DIAL. The screen displays LOCATION?.
2. Press a memory location key (0-9, A, B , C ) to review the memory location’s
content.
• To dial the displayed number, press the SPEAKER button or lift the handset.
• To exit stored number review, press FLASH/EXIT.
• To change the displayed number, press STORE.
• Use the number keys to enter the telephone number (up to 32 digits ) and
press the STORE button to save. (The unit will not dial a phone number in this
model.) The cursor automatically moves to the text line for name entry.
• Use the number keys to enter the name of the person associated with the
telephone number you just entered. More than one letter is stored in each of
the number keys. For example, to enter the name BILL SMITH, press the “2”
key twice for the letter B. Press the “4” key 3 times for the letter I. Press the “5”
key 3 times for the letter L.
Note: The flashing cursor automatically moves to the next position
or you may press the SKIP or REPEAT buttons to move the cursor to
the next position.
• Press the “5 “ key 3 times for the second letter L. Press the arrow key (4) two
times to insert a space. Press the “7 “ key “4” times for the letter S. Press the
“8” key for the letter T. Press the “4” key twice for the letter H.
30
Chain Dialing from Memory
Use this feature to make calls which require a sequence of numbers, for
instance, if you use a calling card for a frequently called long distance number.
Basically, you dial each part of the sequence from memory. The following
example shows how you can use chain dialing to make a call through a long
distance service:
The Number For
Memory Location
Long distance access number
Authorization code (ID)
6
7
8
Long distance phone number
1. Pick up the handset or press SPEAKER.
2. Press DIAL button, then press number “6” for the memory location.
3. Press DIAL button, then press number “7” for the memory location.
4. Press DIAL button, then press number “8” for the memory location.
5. The number dials automatically.
31
Answering System Operation
Call Answering
When a call comes in, the unit will ring the number of times set, play the greeting,
and record the incoming call.
You can:
• Answer the call before the unit answers.
• Pick up the phone during the greeting.
• Listen to the incoming message (Call screening).
• Pick up the phone during the incoming message, if desired.
• Disconnect the caller by pressing the PLAY/STOP button.
Auto Disconnect
Auto disconnect is a feature that tells the unit to stop playing the greeting or
recording when a extension phone is picked up. Sometimes you may pick up and
the machine keeps playing the greeting. This is normal. If you want to pick up the
phone during the greeting play, wait about two seconds after the system answers
before picking up a phone.
If the greeting continues to play after picking up an extension phone, press the
PLAY/STOP button.
3ꢀ
Playing Messages
Use the PLAY/STOP button to play messages. The unit first plays new messages
in the order received. If there are no messages, the unit announces, “You have
no messages.” If there are no new messages, the old messages are played
back.
When playing messages, the message number and the date-time stamp will be
shown on the display.
• To play messages, press and release PLAY/STOP.
• To stop playback, press and release PLAY/STOP again.
• To restart the message that is playing, press the REPEAT button once.
• To replay the previous message, press the REPEAT button twice.
• To play the SKIP message, press and release SKIP.
While playing message, user can press MESSAGE SPEED button to listen to
message playback at a lower speed.
Each press of the MESSAGE SPEED button change message playback speed.
The screen displays current message speed.
Erase Messages
Single Messages
You can erase a message itself, leaving the Caller ID information.
• While the message is playing, press and release DELETE. The unit erases the
current message and announces, “Message erased.”
All Messages
You can also erase all the old messages only, leaving the new messages and
Caller ID information.
While the unit is in ready-to-answer mode, press and hold DELETE until the unit
announces, “Messages erased.”
• New messages can not be erased in this way. To erase new messages, play
them then press DELETE during play back.
33
Leaving a Memo
Use the MEMO button to record a specific message for others who have access
to the unit.
1. Press and hold the MEMO button. The unit announces, “Record your memo
after the tone.”
2. Record your message after the beep.
3. Release MEMO when you’re finished talking. The unit treats the memo as a
message, as the display shows.
Memory Full
When the unit’s memory is full, it answers after 10 rings and announces,
“Memory is full.” A 20-second waiting period follows, allowing you to enter your
security code.
Remote Access
You can access your answerer from any touch-tone phone from another location
by entering your 3-digit security code (the default security code is 1 2 3, but you
can change it.) Be aware that remote functions do not work with rotary or push-
button pulse-dialing phones.
To access your answerer:
1. Call your telephone number.
2. After you hear the beep that follows the greeting, enter your 3-digit security
code. The unit confirms your code with a beep. To bypass the greeting, you
can enter your 3-digit security code any time while the greeting is playing.
The unit waits for a remote command for 20 seconds after the correct security
code has been entered. Menu selections can be made while the menu is playing.
Note: The unit answers on the 10th ring when it is turned off or the
memory is full. To access the answerer, enter the 3-digit security
code after the beep. If memory is full, play messages and erase
some of them to restore memory.
3ꢁ
Note: After the unit plays the remote menu, it waits ꢀ0 seconds for a
command, then disconnects.
Remote Access Commands
Play messages
2
1
3
0
2
4
7
Repeat messages (during message playback)
Skip to next message (during message playback)
Erase message (during message playback)
Stop playback(during message playback)
Turn answerer On/Off
Review menu again
35
Message Indicators
The following special messages indicate the status of a message or the unit:
00 CALLS
The call record log is empty.
UNKNOWN NUMBER
The incoming call does not have Caller ID service or
their service area is not linked to yours. If UNKNOWN
NAME appears along with a calling number, the
name information for that number was not available.
BLOCKED NUMBER
INCOMPLETE DATA
START/END
The caller is registered as “Private Number” and the
Caller ID information is withheld.
Caller information has been interrupted during
transmission.
Indicates you are at the beginning or the end of the
call record log.
MESSAGE
The message has been recorded as a memo.
36
Troubleshooting Guide
Telephone Solutions
No dial tone
• Check the hook switch to make sure it pops up.
Won’t dial out
• Make sure the tone/pulse setting is programmed correctly.
Phone doesn’t ring
• Check the ringer volume.
• Could have too many phones on one line.
(See FCC registration information regarding REN)
Low handset or speaker volume
• Check the volume settings.
Can’t be heard by other party
• Make sure the phone cord is securely plugged in.
• Make sure the MUTE function is OFF.
Memory dialing
• Make sure you entered the numbers correctly. (See “Memory.”)
Answerer Solutions
Doesn’t answer or answers on 10th ring
• Make sure the answerer is turned on.
• Memory is full, erase some messages.
• Check the AC power and phone line connections.
Incoming messages are incomplete
• Was an extension phone picked up?
• The caller left a message that is longer than the message length you set during
setup.
• Memory is full.
37
Won’t respond to remote commands
• Must use a touch-tone phone.
• Must enter the correct security code.
• Did unit hang up? If you take no action for a period of time, it automatically
hangs up.
Answerer doesn’t work
• Unplug the power cord from the electrical outlet and plug it back in to reset the
answerer.
After the unit is plugged in, the screen displays FLASH ERROR
• Unplug the unit and plug it back in. If the message appears again, the unit
needs service.
Can’t hear messages
• Adjust the volume control.
Greeting continues to play even after an extension phone is picked up.
• This is normal operation. Auto disconnect is delayed for 1 second after the unit
answers a call. If you are near the unit, press PLAY/STOP to stop the greeting.
No information is shown after the phone rings
• Be sure to wait until the second ring before answering.
• Check all cabling to make sure that all connections are secure and not
damaged.
• Did you order Caller ID service from your local telephone company?
Error message is displayed
• ERROR appears in the display if the unit detects anything other than valid
Caller ID information during the silent period after the first ring. This message
indicates either the presence of noise on the line, or that an invalid message
has been sent from the telephone company?
38
General Product Care
To keep your product working and looking good, follow these guidelines:
• Avoid putting it near heating appliances and devices that generate electrical
noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping product and/or other rough treatment.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this will
damage the finish.
• Retain the original packaging in case you need to ship it at a later date.
39
Causes of Poor Reception
• Aluminum siding.
• Foil backing on insulation.
• Heating ducts and other metal construction that can shield radio signals.
• You’re too close to appliances such as microwaves, stoves, computers, etc.
• Atmospheric conditions, such as strong storms.
• Base is installed in the basement or lower floor of the house.
• Base is plugged into AC outlet with other electronic devices.
• Baby monitor is using the same frequency.
• Handset battery is low.
• You’re out of range of the base.
ꢁ0
Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this Uniden
Product to be free from defects in materials and craftsmanship with only the limitations or exclusions
set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further effect
12 months after the date of original retail sale. The warranty is invalid if the Product is A) damaged or
not maintained as reasonable or necessary, B) modified, altered, or used as part of any conversion
kits, subassemblies, or any configurations not sold by Uniden, C) improperly installed, D) serviced
or repaired by someone other than an authorized Uniden service center for a defect or malfunction
covered by this warranty, E) used in any conjunction with equipment or parts or as part of any system
not manufactured by Uniden, or F) installed or programmed by anyone other than as detailed by the
owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at any
time while this warranty is in effect, warrantor will either, at its option, repair or replace the defective
unit and return it to you without charge for parts, service, or any other cost (except shipping and
handling) incurred by warrantor or its representatives in connection with the performance of this
warranty. Warrantor, at its option, may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY
PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER
WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING
BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES
NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of incidental or
consequential damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. This warranty is void outside the United States of America and
Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the Product is defective, pack the Product carefully
(preferably in its original packaging). Disconnect the battery (if any) from the Product and separately
secure the battery in its own separate packaging within the shipping carton. The Product should
include all parts and accessories originally packaged with the Product. Include evidence of original
purchase and a note describing the defect that has caused you to return it. The Product should be
shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
ꢁ1
Index
A
G
Answering System Operation...................32
Answering System Setup .........................11
Auto Disconnect .......................................32
General Product Care...............................39
H
Hearing Aid Compatibility ...........................3
B
I
Base Layout................................................8
If You Did Not Program Your Local Area
Before You Begin........................................6
Code ..................................................25
If You Programmed Your Local Area
C
Code ..................................................24
Call Answering..........................................32
Caller ID Features ....................................22
Caller ID with Call Waiting........................23
Causes of Poor Reception........................40
Chain Dialing from Memory......................31
Changing a Stored Number......................29
Important Information .................................2
Important Installation Information...............7
Important Instructions for Moving the
Answerer............................................11
Inserting a Pause in the Dialing
Sequence...........................................29
Copying Caller ID Memories to User
Installing the Phone....................................9
Interference Information .............................2
Introduction.................................................6
Memory ..............................................28
D
Deleting CID Records...............................24
Desktop Installation....................................9
Dialing a Number Stored in Memory ........29
L
Leaving a Memo.......................................34
Licensing ....................................................3
Dialing a Number Stored in Memory
While On-hook ...................................29
M
Dialing Back..............................................24
Memory.....................................................26
Memory Full..............................................34
Message Indicators ..................................36
Message Volume......................................20
Mute..........................................................14
E
Erase Messages.......................................33
Erasing a Stored Number.........................28
F
FCC RF Radiation Exposure Statement.....3
Flash .......................................................14
ꢁꢀ
Index
Storing a Number in Memory ...................26
Storing a Redial Number to Memory........27
Summary Screen......................................22
Switching between Speaker and Handset13
P
Parts Checklist............................................6
Placing a Phone Call................................13
Playing Messages ....................................33
T
R
Telephone Jack Requirements...................6
Telephone Network Information..................2
Telephone Operation................................12
Telephone Set Up.....................................15
Temporary Tone Dialing............................13
Troubleshooting Guide .............................37
Receiving a Phone Call............................13
Receiving and Storing Calls .....................23
Recording the Outgoing Announcement...11
Redial .......................................................14
Remote Access.........................................34
Remote Access Commands.....................35
REN Number ..............................................3
Reviewing Call Records ...........................23
Reviewing Stored Numbers......................30
Reviewing the Announcement..................12
Ringer Volume..........................................20
U
Using the Speakerphone..........................12
W
Wall Mounting the Phone .........................10
Warranty...................................................41
S
Setting Day of Week.................................18
Setting the Dialing Mode ..........................18
Setting the Display Contrast.....................17
Setting the Incoming Message or Memo
Length ................................................16
Setting the Language ...............................20
Setting the Recording Quality ..................16
Setting the Rings to Answer .....................15
Setting the Security Code.........................17
Setting the Time and Date........................19
Setting Your Local Area Code...................18
Speakerphone Location............................12
Speakerphone Use...................................12
Speakerphone Volume.............................21
ꢁ3
OR
If You...
Contact Uniden’s...
Phone Number
817-858-2929 or
800-297-1023
have a question or problem Customer Care Line*
need a part or accessory
Parts Department*
800-554-3988
need special assistance
due to a disability
800-874-9314
(voice or TTY)
Accessibility Help Line
* During regular business hours, Central Standard Time.
Visit our website for detailed business hours.
Model 1380
Printed in China
© 2009 Uniden America Corp.
Fort Worth, TX.
|