Uniden Cell Phone DCX 490 User Manual

 
Install the battery pack  
Charge the battery pack for at least 12-15 hours before  
plugging the phone line into your phone.  
Press in on the battery cover  
release and slide the cover down  
until it comes off.  
1
Connect the battery pack  
2
connector observing the correct  
polarity (black and red wires) to  
the jack inside the battery  
compartment.  
Do not exert any force on this  
connection. It could cause damage to  
the battery or to the handset. The  
plastic connectors will fit together in  
only one way.  
Once you are certain that you have  
made a good connection, then insert  
the battery pack into the battery  
compartment. Do not pinch the wires.  
Securely close the battery  
compartment cover by sliding it  
until it snaps into place.  
3
Place the handset in the charging  
cradle.  
4
When the battery is charged, the LCD  
will display “Initializing...”  
for 5 to 10 seconds.  
Use only the Uniden battery  
(BP-490) supplied with your  
phone. Replacement batteries  
are also available through the  
Uniden Parts Department.  
(See page 2)  
– 3 –  
 
Bat t ery use t ime ( per charge)  
Fully charged  
• 6 hours continuous use  
• 3 days when the handset is in the standby mode  
Low bat t ery alert  
When the battery pack is very low and needs to be charged, the  
phone is programmed to eliminate functions in order to save  
power. “BATT” appears on the display and you will hear a beep.  
If the phone is in use, “BATT”  
appears on the display and the  
handset beeps twice. Complete your  
conversation as quickly as possible  
and return the handset to the base  
unit for charging.  
When the call is terminated due to a low battery,  
the call will be placed on hold and can be  
retrieved from any of the other handsets.  
Cleaning t he bat t ery charging cont act s  
To maint ain a good charge, it is  
import ant t o clean t he bat t ery  
cont act s on t he handset and base  
unit wit h a dry clot h or a pencil  
eraser about once a mont h.  
Do not use any liquids or solvent s.  
Connect the AC adapter to the DC  
1
IN 9V jack to a standard 120V AC  
wall outlet.  
Set the charger on a desk or  
tabletop, and place the handset  
in the charger as shown.  
2
Make sure that the charge LED  
3
lights up. If the LED does not  
light up, check to see that the AC  
adapter is plugged in and that the  
handset makes good contact with  
the base charging contacts.  
– 4 –  
 
To set up addit ional handset s  
Follow the simple steps to register your new additional handset.  
Check that the phone is not in use (including the intercom),  
and make sure that the handset is not in the base unit.  
1
Press and hold the find handset key on the base  
for 5 seconds.  
2
- The charge/ voice mail LED will start flashing to tell you  
that the system is in the registration mode.  
Place the NEW (the 3rd) handset in the charging cradle of the  
base unit.  
3
- The handset beeps to tell you that the registration has  
finished.  
Reset t ing t he handset  
This feature allows you to clear (erase) all the selections and  
settings of the handset. After you have reset the handset, you  
must change the digital security code and re-register the  
handset before use.  
Press menu/ ent er key.  
1
Press L or L and select “Handset Reset.  
2
Press menu/ ent er, “No?” appears on the display.  
3
4
Press L or L to change the selection.  
- “Yes” is to reset and “No” is to exit this mode.  
Press menu/ ent er to confirm your selection.  
5
6
Wait 5 to 10 seconds for the handset to complete the reset.  
(“Initializing. . .” appears on the display.)  
When the reset is complete, the LCD will display  
Handset is not registered.  
7
– 5 –  
 
Changing the Digital Security Code  
The digital security code is an identification code used to  
connect the handset and the base unit. Normally, setting the  
code is not necessary unless you are replacing an extra handset.  
In the rare situation that you suspect another cordless  
telephone is using the same security code, you can change the  
code.  
Your DCT 4960-2 has the capability of expanding to  
4 handsets. In any event that a handset is lost or  
damaged, the base unit security code will need to be  
changed, once a replacement handset is registered.  
Unplug the AC Adapter.  
1
2
Press and hold find handset on the base while you plug in  
the AC Adapter, and keep holding find handset for 10  
seconds.  
The security code has changed.  
3
* After changing the security code, please be sure to re-  
register all the handsets before use.  
Re-regist ering t he handset  
When you change the security code on the base, the handset  
needs to be re-registered.  
Follow the simple steps shown below:  
Check that the phone is not in use (including the intercom),  
and make sure that the handset is not in the base unit.  
1
Press and hold find handset on the base for 5 seconds.  
2
- The charge/ voice mail LED will start flashing to tell you  
that the system is in the registration mode.  
Press menu/ ent er on the handset.  
3
4
Press L or L and select  
Registration.  
– 6 –  
 
One Year Limit ed Warrant y  
Important: Evidence of original purchase is required for warranty service.  
WARRANTOR: UNIDEN AMERICA CORPORATION (Uniden”)  
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this  
Uniden Product to be free from defects in materials and craftsmanship with only the  
limitations or exclusions set out below.  
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further  
effect 12 months after the date of original retail sale. The warranty is invalid if the Product  
is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used  
as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,  
(C) improperly installed, (D) serviced or repaired by someone other than an authorized  
Uniden service center for a defect or malfunction covered by this warranty, (E) used in any  
conjunction with equipment or parts or as part of any system not manufactured by Uniden,  
or (F) installed or programmed by anyone other than as detailed by the owners manual for  
this product.  
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at  
any time while this warranty is in effect, warrantor will either repair or replace the defective  
unit and return it to you without charge for parts, service, or any other cost  
(except shipping and handling) incurred by warrantor or its representatives in connection  
with the performance of this warranty. Warrantor may replace the unit with a new or  
refurbished unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE  
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER  
WARRANTIES OF ANY NATURE WHATSOEVER, WHETHER EXPRESSED, IMPLIED OR ARISING BY  
OPERATION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT  
COVER OR PROVIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR  
CONSEQUENTIAL DAMAGES. Some states do not allow this exclusion or limitation of  
incidental or consequential damages so the above limitation or exclusion may not apply  
to you.  
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. This warranty is void outside the United States of  
America.  
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions  
in the owners manual you are certain that the Product is defective, pack the Product  
carefully (preferably in its original packaging). The Product should include all parts and  
accessories originally packaged with the Product. Include evidence of original purchase and a  
note describing the defect that has caused you to return it. The Product should be shipped  
freight prepaid, by traceable means, to warrantor at:  
Uniden America Corporation  
Parts and Service Division  
4700 Amon Carter Blvd.  
Fort Worth, TX 76155  
(800) 297-1023, 7 a.m. to 7 p.m. Central, Monday through Friday  
– 7 –  
 
Printed in China  
381-000805  
 

Teac Fryer SM80G User Manual
The Vollrath Co Food Warmer Drop In Hot Wells User Manual
Timex Heart Rate Monitor M187 User Manual
Toastmaster Bread Maker 1170S User Manual
Toshiba Digital Camera IK DP01A User Manual
Toshiba Telephone CTX670 User Manual
Tunturi Tent C 900 User Manual
Vidikron Projector 40828 User Manual
Viking Cooktop VGIC245 4B User Manual
Weber Charcoal Grill 30185 User Manual