USE AND CARE GUIDE
®
1000, 29 & 75 SERIES
WINE CAPTAIN® MODELS
BEVERAGE CENTERS
REFRIGERATORS, FREEZERS
WINE CAPTAIN®
MODELS
BEVERAGE
CENTER
REFRIGERATOR
FREEZER
ULN-29RB-00
ULN-29RB-02
ULN-29RB-06
ULN-29RB-09
ULN-29RB-13
ULN-29RB-15
ULN-29RWH-00
ULN-29RWH-02
ULN-29RWH-06
ULN-29RWH-09
ULN-29RWH-13
ULN-29RWH-15
ULN-29RWH-23
ULN-29RWH-25
U-1075WCS-00
U-1075WCS-02
U-1075WCS-13
U-1075WCS-15
U-1075BEVS-00
U-1075BEVS-02
U-1075BEVS-13
U-1075BEVS-15
ULN-75FB-00
ULN-75FB-13
ULN-75FWH-00
ULN-75FWH-02
ULN-75FWH-13
The Built-In Undercounter Leader Since 1962
U-LINE.COM
Table of Contents
1 - Safety Precautions .....................................................................................................................................................1
Safety Alert Definitions ........................................................................................................................................1
General Precautions .............................................................................................................................................1
2 - 1000 Series Product Features ................................................................................................................................2
All 1000 Series Models Feature: ........................................................................................................................2
Wine Captain® Model and Beverage Center Features: ..............................................................................2
Wine Captain® Model Features: .......................................................................................................................2
Beverage Center Features: .................................................................................................................................2
Refrigerator and Freezer Features: ...................................................................................................................2
3 - Product Operation ...................................................................................................................................................3
Air Flow ...................................................................................................................................................................3
Initial Startup ..........................................................................................................................................................3
Control Dial ...........................................................................................................................................................3
Adjusting Air Temperature .................................................................................................................................4
Interior Lighting .....................................................................................................................................................4
Checking Product Temperature ........................................................................................................................4
4 - U-Line Wine Guide ..................................................................................................................................................5
Looking Behind the Label ....................................................................................................................................5
Wine Selections Suggestions ..............................................................................................................................5
Ideal Wine Storage Considerations ..................................................................................................................6
Wine Stocking Recommendation ......................................................................................................................7
Wine Rack Removal and Installation ................................................................................................................7
Wood Trim Finishing ...........................................................................................................................................8
5 - Maintenance ...............................................................................................................................................................9
Light bulb Replacement .......................................................................................................................................9
Leveling ....................................................................................................................................................................9
Removing and Installing Interior Shelves .........................................................................................................9
Removing and Installing Door Shelves .......................................................................................................... 10
Removing and Installing Grille ......................................................................................................................... 10
6 - Standard Doors ...................................................................................................................................................... 11
Door Alignment and Adjustment ................................................................................................................... 11
Door Reversability ............................................................................................................................................. 11
Reversing the door ............................................................................................................................................ 11
7 - Cleaning .................................................................................................................................................................... 13
Exterior Cleaning ............................................................................................................................................... 13
Interior Cleaning ................................................................................................................................................ 13
Defrosting ............................................................................................................................................................ 13
Condensor Cleaning .......................................................................................................................................... 14
Storage, Vacation and Moving ......................................................................................................................... 14
Product Disposal ................................................................................................................................................ 14
8 - Service ...................................................................................................................................................................... 15
Normal Operating Sounds ............................................................................................................................... 15
Troubleshooting Guide ..................................................................................................................................... 15
Before Calling for Service ................................................................................................................................ 15
If Service is Required ......................................................................................................................................... 15
Replacement Parts ............................................................................................................................................. 15
U-Line Use and Care Table of Contents
1 Safety Precautions
General Precautions
Use this appliance for its intended purpose only. Follow these
general precautions with those listed throughout this guide:
IMPORTANT
• PLEASE READ all instructions before installing,
operating, or servicing the appliance.
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away your
old refrigerator or freezer, take off the doors and leave shelves
in place so children may not easily climb inside.
• Proper installation procedures must be followed when
completing an installation or relocation of a unit.
Consult the installation guide before any installation
begins. U-Line contact information appears on the rear
cover of this guide.
WARNING
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform maintenance on
the unit until the electricity has been disconnected.
• Never remove the round grounding prong from the
plug and never use a two-prong grounding adaptor.
• Altering, cutting of power cord, removal of power
cord, removal of power plug, or direct wiring can
cause serious injury, fire and or loss of property and
or life, and will void the warranty.
• This unit requires connection to a dedicated 15 Amp
grounded (three-prong), polarized receptacle, installed
by a qualified electrician, compliant with applicable
electrical codes.
Safety Alert Definitions
• Never use an extension cord to connect power to the
unit.
• Always keep your working area dry.
Throughout this guide are safety items labeled with a Danger,
Warning or Caution based on the risk type:
WARNING
DANGER
Install provided Anti-Tip kit. Serious personal
injury could occur.
Danger means that failure to follow this safety statement will
result in severe personal injury or death.
CAUTION
• Use care when moving and handling the unit. Use gloves
to prevent personal injury from sharp edges.
• If your model requires defrosting, DO NOT use an ice
pick or other sharp instrument to help speed up
defrosting. These instruments can puncture the inner
lining or damage the cooling unit. DO NOT use any type
of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
property or equipment damage.
CAUTION
IMPORTANT
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
• Do not lift unit by door handle.
• Never install or operate the unit behind closed doors.
Be sure front grille is free of obstruction. Obstructing
free airflow can cause the unit to malfunction and will
void the warranty.
• Failure to clean the condenser every six months can
cause the unit to malfunction. This could void the
warranty.
• Allow unit temperature to stabilize for 24 hours before
use.
• Do not Block any internal Fans
Use only genuine U-Line replacement parts. Imitation
parts can damage the unit, affect its operation or
performance and may void the warranty.
1
Precautions
Wine Captain® Model Features:
2 1000 Series Product Features
All 1000 Series Models Feature:
Capacity. 24" Wine Captain Model up to 48 Bottles.
Triple temperature zones. Maintains wine at their proper
serving temperature. Top Approximately 55°F (Red). Middle
Approximately 50°F (White). Bottom Approximately 45°F
(Sparkling). Safely stores one, two or three types of wine.
3/4 extension slide-out coated wine racks. Allow for easy
access to all wine bottles. Four or eight wine bottle capacity
(0.75 L) on each rack.
Mechanical Temperature Control. Provides ability to set the
temperature.
Vinyl-clad cabinet. Textured, rich appearance. More resistant to
scratching, peeling and flaking.
Stable temperatures. Stable, consistent temperatures provide
longer-term storage capability.
Integrated handle. Does not add depth to the cabinet when
built in. Black and white models only.
Built-in. Provides custom look. No additional clearance required
around sides, top or rear of unit for ventilation. Do not obstruct
front grille.
Field-reversible doors. Flexible installation options. All models
with black and white doors are field-reversible. Stainless steel
models with glass doors are field-reversible. Stainless steel models
with solid doors must be order right- or left-hand hinged.
Beverage Center Features:
Capacity. 24" Beverage Center 5.6 cubic feet
Adjustable leveling legs. Achieve a more precise under counter
fit. Durable, strong legs will not bend when unit is installed.
Dual temperature zones. Maintain two distinct temperature
zones. Cooler at the top of the cabinet for storage of fine wines
and coldest at the bottom to store your favorite beverages.
Defrost Type: Automatic (cycle) Defrost.
For indoor use only.
Two full-size, removable glass shelves. Generous storage area
for beverages.
Wine Captain® Model and Beverage
Center Features:
3/4 extension slide-out coated wine racks. Allow for easy
access to beverages.
Low-E coated, gas filled thermal glass door. Allows for
effective product presentation. Protects wine and other products
from potentially harmful ultraviolet light rays.
Built-in or freestanding. Provides custom look when built-in
with no additional venting clearance required on sides, top or rear.
Do not obstruct the grille.
Wood trimmed wine racks. Wood can be stained or replaced
with a solid surface material to match surrounding décor.
Refrigerator and Freezer Features:
Capacity. 29 Model Refrigerator Capacity 3.3 cubic feet.
75F Model Freezer 5.22 cubic feet.
Stainless steel model. Offers a bold stainless steel handle,
stainless steel wrap door with black "cap" on top and bottom of
the door.
Recessed interior light. Automatically illuminates when door is
opened. Does not interfere with product access or storage.
Flat recessed grille. Blends with the other models and
integrates with surrounding cabinetry.
Adjustable tempered glass shelves. Sleek, streamlined
interior. Allows flexible shelf locations to meet varying food and
beverage storage needs. Three in Refrigerator, four in freezer.
Two adjustable in-door storage shelves. Easy access storage
area, right where you need it. Adjustable to allow flexible storage
options.
Door will accept a 1/4" panel. Ability to match surrounding
décor and cabinets. Black and white models only.
Built-in or freestanding. Provides custom look when built-in
No additional venting required on sides, top or rear. Do not
obstruct the grille.
Flat recessed grille on Refrigerator. Blends with the other
models and integrates with surrounding cabinetry.
Model 29 Refrigerator is Energy Star qualified. Saves energy,
saves money, saves our natural resources.
All features and specifications are subject to change.
U-Line 1000 Series Product Features
2
3 Product Operation
Air Flow
Initial Startup
All U-Line controls are preset at the factory. Initial startup requires
no adjustments.
IMPORTANT
IMPORTANT
The unit requires proper air flow to perform at its highest
efficiency. Do not block the front grille or internal fans at
any time, or the unit will not perform as expected. Do not
install the unit behind a door.
U-Line recommends allowing the unit to run overnight
before loading refrigerator or freezer with product.
To turn the unit on:
Turn the control dial found in the center of the grille to a MID
setting, number 3 or 4 on the controller knob.
To turn the unit off, turn the control dial counterclockwise until
hearing a “click”. It may take some force to get the control to
“click”.
Control Dial
Wine Captain Models provide three temperature zones within the
cabinet to satisfy the specific storage requirements of your finest
wines.
The control dial sets a single continuous set-point temperature.
This set point is for the middle zone, it is a base number used by
the controller to maintain the multiple temperature zones in the
unit. The factory default MID setting set-point for Beverage Center
and Refrigerator models is 38°F. The factory default MID setting
set-point for Wine Captain models is 50°F. The set-point
temperature is a gauge for further temperature adjustments.
3
U-Line Product Operation
Checking Product Temperature
Adjusting Air Temperature
IMPORTANT
• Adjust the set point temperature in single increments,
and wait 24 hours for the temperature to stabilize
before rechecking.
• Factory recommended set-point is MID setting on dial
control.
To adjust the set point temperature:
Adjust the temperature by turning the numbered dial (1) in
small increments.
To check the actual product temperature in the unit.
1. Partially fill a plastic (nonbreakable) bottle with water.
2. Insert an accurate thermometer.
1
2
3. Tighten the bottle cap securely.
Interior Lighting
4. Place the bottle in the desired area for 24 hours.
5. Avoid opening the unit during the testing period.
Normal Operation. Opening the door will cause the interior of
the cabinet to illuminate.
6. After 24 hours, check the temperature of the water. If required,
adjust the temperature control in a small increment (See
ADJUSTING TEMPERATURE).
Some models with glass doors have a LIGHT button (2) on the
control panel. Note, on some models this is an On Off switch.
With this switch turned on the interior light will remain illuminated
with the door closed. Do not leave the light on for more than a
four-hour period.
Causes which affect the internal temperatures of the
cabinet include:
•
•
•
•
•
Temperature setting.
Ambient temperature where installed.
Installation in direct sunlight or near a heat source.
The number of door openings and the time the door is open.
The time the internal light is illuminated. (This mainly affects
product on the top rack or shelf.)
•
The front grille or condenser are obstructed.
U-Line Product Operation
4
4 U-Line Wine Guide
Matching Food and Wine
Although there are no hard fast rules for matching wine to food,
observe some guidelines. Delicate dishes should be accompanied
by lighter more delicate wines. Full-flavored foods should be
matched with fuller-bodied wines.
Looking Behind the Label
To most, wine is a delicious mystery. We purchase it, uncork it, and
savor its taste and beauty. But there is so much more to true wine
appreciation. Many secrets are simply too good to keep bottled up.
As a general rule, one should aim to ascend in flavor and quality of
wines served.
Wine Selections Suggestions
Serve a:
DRY wine
Before a:
SWEET wine
RED wine
Selecting the right wine for the right occasion can sometimes be a
seemingly awkward or difficult task for the beginning wine
enthusiast. We would therefore like to present you with a few
suggestions which may provide a little more confidence and
enjoyment when choosing and serving your wines.
WHITE wine
YOUNG wine
LIGHT-BODIED wine
OLD wine
FULL-BODIED wine
When selecting wines, keep an open mind and do not be afraid to
be adventurous. Do not view the subject of wine so seriously it
discourages you from learning and discovering for fear of
embarrassment if something is incorrect. Wine is best viewed as a
hobby and enjoyed.
Any step back in quality will be noticed. If a fine wine is tasted prior
to a lesser wine, many of the fine wine’s subtle qualities may be
missed.
Common Food and Wine Matches
When assembling your collection, try not to become obsessed
with “Vintages.” Although a chart can be a useful tool,
generalizations about a specific year have led more than one
collector to disappointment. Often an “Off Year” will provide a
better value and more drinking enjoyment.
Foods
Wines
Fish, Shell Fish, Crab, Oysters
Dry White Wines, Light Sparkling
or Extra Dry Champagne
Beef, Venison
Pork, Veal, Lamb and Poultry
Fruit
Full-Bodied Red Wines
Light-Bodied Red Wines
Sweet White and Sparkling Wines
The primary guideline to the subject of wine is your own palate.
Do not be afraid to make mistakes. Experiment, discover, but most
of all, enjoy yourself and your new U-Line product.
A Toast to Wine Truths
Guide To Common Styles Of Wine
Like the grapes themselves, many wine myths have been cultivated
over the centuries.
Red Wines
Full-Bodied Dry
California
French
Italian
Zinfandel, Cabernet
Rhone, Chateauneuf-du-
Pape
Myth 1: Most wines taste better when aged.
Barbaresco, Barolo
Truth: In fact, less than 5% of wines produced today are meant to
be aged. Most wines are crafted to be consumed within the first
one to two years.
Medium-Bodied Dry
Light-Bodied Dry
California
French
Pinot Noir
Bordeaux, Burgundy
French
Italian
Beaujolais
Chianti, Bardolino
Myth 2: Wines should be uncorked and decanted allowing them
to "breathe."
White Wines
Truth: To breathe or not breathe? While it is better to allow a
young tannic Red to breathe in a glass or decanter to soften the
tannins, an old Red reaches a stage in its life where it should be
enjoyed soon after opening. Allow an old Red to breathe for a
short time to dissipate any off odors. Most white wines can be
served, ideally, 10-15 minutes after opening.
Full-Bodied Dry
California
French
Chardonnay
Montrachet, Meursault
Puligny-Montrachet
Medium-Bodied Dry
California
French
Sauvignon-Blanc
Pouilly-Fuisse, Sancerre,
Vouvray, Graves
Myth 3: When age worthy wines peak, they must be consumed
almost immediately.
Light-Bodied Dry
French
Chablis, Muscadet, Pouilly-
Fume
Truth: Most great wines reach a plateau period rather than a peak.
Great Bordeaux's may have as much as a 10-year plateau before
fading.
Full-Bodied, Very Sweet
Germany
Frency
Hungary
Beerenauslese
Sauternes
Tokay
Medium-Bodied, Semi-
Sweet
California
Germany
Gewurtztraminer
Liebfraumilch
Myth 4: Wine color does not change with aging.
Truth: As red wines age they get lighter in color while whites get
darker.
Light-Bodied Off Dry
Germany
Rhine, Mosel, Riesling
5
U-Line Wine Guide
The Cork: A Mystery on Its Own.
Ideal Wine Storage Considerations
Cork Presentation. The ritual of the presentation of the cork
has a rich and fascinating history dating back to the late 1800's. A
phylloxera (root louse) devastation to the vineyards severely
limited the supply of great wines. Restaurateurs would remove
labels on inferior wines and replace them with labels from superior
wines. This made it necessary for patrons to protect themselves by
checking the branding on the cork to ensure that what they
ordered was, in fact, what they were served.
Temperature: The most important element about storage
temperature is stability. If wine is kept in a stable environment
between 40°F and 65°F, it will remain sound. A small 1-2 degree
temperature fluctuation within a stable environment is acceptable.
Larger temperature fluctuations can affect the corks ability to seal,
allowing the wine to "leak" from the bottle.
Humidity: The traditional view on humidity maintains that wines
should be stored on their sides in 50% - 80% relative humidity to
ensure cork moisture and proper fit in the bottle. Contemporary
wisdom suggests that the cork surface is too small to be impacted
by humidity. Further the cork is sealed with a metal or wax capsule
making humidity penetration impossible. The concept of a humid
storage environment was derived from the necessity of wineries to
maintain moisture in their cellars to keep wooden barrel staves
swollen, preventing wine evaporation and product loss. In fact,
vineyards estimate as much as a 10% product loss per year due to
evaporation while wine is aging in the wooden barrels. Humidity,
however, was not intended for the modern home cellar where
wine is stored in glass bottles with sealed corks.
When presented with a cork today, feel it to check for its integrity,
read and match the branding on the cork to the bottle and set it
aside. There is little to be learned from the cork. The proof is in
the wine.
Corked" wines. If you've ever had a wine that smelled or tasted
of mold, you've experienced a wine that may have been "corked."
Today, between five and eight percent of wines are tainted with
Trichloroanisole (TCA). This substance, found naturally in plants
and trees, is imparted to the wine through the cork. Corked
wines are a major concern for winemakers as it destroys millions
of cases per year and puts reputations at stake. Amazing as it may
seem twist-off caps may offer a better alternative and many great
wineries in California, Australia and New Zealand are pioneering
the trend.
Light: UV rays are not only harmful to people, they are damaging
to wines - especially those in clear bottles. Since oxygen molecules
in wine absorb UV rays, wine should never be stored in direct light
for long periods of time.
Common Tasting Terms
Vibration: Provided that sediment is left undistributed and
particles are not suspended, vibration in a storage environment is
not an issue. Wines can become flat or tired when voids and
vacuums are created inside the wine bottle. In order to create
voids and vacuums within a liquid, aggressive motion or shaking of
the wine bottle would have to occur.
Te rm in olog y
Description
Acidity
A critical element of wine that is responsible for
preserving the wines freshness. Excess acidity
results in an overly tart and sour wine.
Balance
Body
A desired trait where tannin, fruit and acidity are
in total harmony. Wines with good balance tend
to age gracefully.
The Right Temperature for Wine
The weight and presence of wine in the mouth
provided by the alcohol and tannin level. Full-
bodied wines tend to have this strong
concentration.
Te mpe rature
Wines
Red
Approximately 60°F (15°C)
50°F - 55°F (10°C -12°C)
Approximately 45°F (7°C)
White
Sparkling
Bouquet
Complex
The blending of a wine's aroma within the bottle
over a period of time, caused by volatile acidity.
A subjective term often used in tasting. A wine is
said to be complex if it offers a variety of flavors
and scents that continue to evolve as it develops.
Wine Captain® Models - A Touch of Elegance
Flabby
Full-Bodied
Lean
A wine that lacks structure, or is heavy to the
taste, lacks acidity.
In 1985 U-Line was the first North American appliance manufac-
turer to develop a residential wine storage unit, the Wine Cap-
tain®. Each U-Line Wine Captain® model is designed to impress
and inspire anyone with an interest in wine by providing cellar con-
ditions in stylish, undercounter units. U-Line Wine Captain® mod-
els offer stable storage temperatures, a 50% internal relative
humidity and protection from UV light rays. U-Line has the largest
product offering available, making storing, presenting, and sharing
your wine effortless and elegant.
Wine high in alcohol and extract, generally
speaking, fills the mouth, powerful.
Generally describes wines that are slim, lacking of
generosity or thin.
Oaky
A desirable flavor imparted to wine if done in
moderation. Most wines are aged in oak barrels
one to three years, thereby receiving this toasty
oak characteristic. However, if a weak wine is left
in contact too long with an oak barrel it will tend
to be overpowered with an oaky taste.
Tannin
Tannins are extracted from the grape skins and
stems and are necessary for a well-balanced red
wine. Tannins are easily identified in wine tasting
as the drying sensation over the gums. Tannins
generally fade as a wine ages.
U-Line Wine Guide
6
Wine Stocking Recommendation
Wine Rack Removal and Installation
Specially designed horizontal wine racks properly positioned the
bottles so the wine remains in contact with the cork and assure
the cork does not become dry.
To remove a rack from the cabinet:
1. Remove any bottles stored on the rack.
2. Grasp the end of the rack, and gently slide it out until it stops.
Stock the unit as follows:
1. Stock the wine racks beginning with the lowest rack, at the
back, and working forward. Stagger the bottles as shown.
3. Press the left rack release lever down. At the same time, lift the
matching right rack release lever up. Pull the rack out until it is
free of the tracks and the cabinet.
2. Repeat Step 1 to stock the next higher rack, and continue until
all racks are filled.
NOTE: After stocking, allow unit to run 24 hours to
stabilize product temperatures.
IMPORTANT
Do not remove the track rails from the cabinet.
To insert a rack in the cabinet:
Align the left and right rack channels with the tracks in the cabinet.
Ensure an even track engagement on both sides by gently pushing
the rack into the cabinet until it stops.
Before reloading the rack, ensure proper movement of the
travel stops in the left and right track rails by pulling the rack
7
U-Line Wine Guide
Wood Trim Finishing
Staining and final finish application:
IMPORTANT
WARNING
You MUST remove the wood trim from the unit for
staining or finishing to prevent permanent damage to
the inner liner of the unit. Allow stain or finish to dry
thoroughly (at least 24 hours for each coat) following
the product manufacturer’s instructions before
reinstallation. Not following this warning may cause the
inner liner of the unit to have a permanent odor, which
the warranty will not cover.
DO NOT use oil-based stains on wood trim. Vapors from
oil-based stains will permanently penetrate the liner and
will not dissipate over time.
1. Remove all screws securing wood trim to interior parts, and
remove the trim from the cabinet interior.
2. Lightly sand and clean wood.
®
U-Line products featuring wine storage include wood-trimmed
wine racks.
3. Apply Minwax Water-Based Wood Stain to wood with a
synthetic bristle brush or a foam applicator. Allow stain to
penetrate about three minutes. Before the stain is dry, take a
stain dampened rag and remove any excess stain remaining.
Wipe towards the grain with medium pressure to achieve the
desired stain color.
Models with wood colored wood trim come factory coated with a
clear vinyl sealer without a finish coat applied, which will
sufficiently protect the wood in normal use. You may coat the trim
on the racks with stain or a final finish following these guidelines. If
using custom wood trim also follow these guidelines.
4. After two hours, repeat step 2. This will even out the color of
the wood.
If staining the trim, stain before applying any final finish. Review the
following staining and final finish application and final finish-only
application guidelines when staining or sealing the wood to ensure
proper adhesion and durability of the finish.
5. Allow stain to dry for a minimum of three hours before applying
the final finish.
6. If desired, sand the wood with very fine sandpaper to smooth
the surface after staining.
NOTE: On glass door models the stain may appear darker
when viewed through the glass.
®
7. Remove all dust from the wood, and apply one coat of Minwax
®
Polycrylic Protective Finish using a synthetic bristle brush.
Apply this finish in a thin coat following the grain. Apply the finish
to the back and sides of the wood first, and allow it to dry for
two hours. Apply the finish to the front side of the wood next,
and allow it to dry for two hours. Sand with 220 grit sandpaper.
Apply two morel coats of finish in the same manner, but do not
sand the trim after applying the final third coat.
8. Allow the final coat to dry for 24 hours before reinstalling the
trim to the cabinet interior parts.
Final finish-only application:
1. Remove all screws securing wood trim to interior parts, and
remove the trim.
2. Lightly scuff sand the wood trim with 280 or finer grit sandpaper.
3. Remove sanding dust with a clean, dry cloth.
4. The factory-applied seal is compatible with almost all finishes. A
®
low odor, water clean up, quick-drying finish such as Minwax
®
®
Polycrylic Protective Finish is recommended (Minwax
®
Polycrylic is an ultra fast-drying water-based finish). Apply a
thin coat of a clear, protective finish, following the container
label directions.
5. Lightly sand and reapply if desired.
Allow the final coat to dry for 24 hours before reinstalling
the trim to the cabinet interior parts.
U-Line Wine Guide
8
5 Maintenance
For Models without adjustable leveling feet:
IMPORTANT
Light bulb Replacement
To replace the light bulb in your U-Line unit:
The unit must be located on a level surface, for proper
door and ice maker (if equipped) operation.
1. Find the light located at the top of the unit. Grasp the edges of
the light housing lens (1) opposite the exposed tab and gently
push the lens toward the tab (2).
1. Use a level to check the levelness of the unit from front to back
and from side to side. Place the level along top edge and side
edge as shown (1).
2. Pull the edge of the lens down (1) and swing it out of the light
housing.
Removing and Installing Interior Shelves
2
1
3
IMPORTANT
ALWAYS use a genuine U-Line replacement 120V 10 watt
bulb (Part Number 31317) in the light housing. Use of any
other bulb within the housing will produce excessive heat,
causing damage to the light housing and cabinet interior,
and will compromise the precise temperature control of
the unit.
1
2
1. Replace the lens by first inserting the tab side back into the
housing at a slight angle.
2. While gently pushing the lens towards the tab end, push the free
end into the housing, and release when you hear a snap.
For models equipped with glass shelves having recessed shelf
supports, remove the shelves as follows:
Leveling
1. Pull shelf out about 6" (1), until back of shelf clears the “hump”
on the right-hand side.
IMPORTANT
2. Tilt up right-hand edge of shelf (2).
3. Remove shelf from unit by pulling out (3).
Insert the shelves as follows:
Unit must be level, for proper door and ice maker (if
equipped) operation.
For Models with adjustable leveling feet:
1. To move to a different position in the unit, insert shelf at an
angle, approximately 15-20°, over the rib in the side of the unit
where you want to place the shelf. Place the shelf into the unit
at an angle to clear the door.
1. Use a level to check the
levelness of the unit from front
to back and from side to side.
Place the level along top edge
and side edge as shown (1).
2. Continue to slide the shelf into the unit at an angle until it clears
the door.
2. If the unit is not level, rotate
the adjustable leveling legs to
raise or lower each corner of
3. Lower the shelf and push it in completely. Ensure the raised edge
strip is toward the rear of the unit and the decorative graphics, if
applied, are on the underside of the shelves.
the unit (5) as necessary.
1
3. Check levelness after each
adjustment and repeat the
previous steps until the unit is
level.
IMPORTANT
• Make sure the shelves are inserted fully into the unit.
•
The edge strip toward the rear prevents cans and
bottles from freezing against the cold evaporator.
9
U-Line 1000 Series Maintenance
Removing and Installing Grille
WARNING
Disconnect electric power to the unit before removing
the grille.
WARNING
DO NOT touch the condenser fins(4). The condenser
fins are SHARP and can be easily damaged.
Removing the grille.
1. Disconnect power to the unit.
2. Remove control knob (6) if equipped.
For models equipped with glass shelves having shelf supports,
remove the shelves as follows:
3. Loosen the two screws (1). Some models may have only one
screw in the center.
1. Open door completely.
4. Remove grille (2) and grille cap (if equipped)(3) from unit.
2. Grasp the shelf edge in the center and slide the shelf from the
unit.
Installing the grille:
1. For 15 and 29 models make sure grille cap (3) is behind grille in
slots (2) provided in grille before attaching grille to unit.
Insert the shelves as follows:
3. Reposition the shelf as required, ensure the raised white edge
strip is toward the rear of the unit and graphics, if applied, are on
the underside of the shelves.
2. For 75 models place the hook-hinge located on the rear bottom
side of the grille (2) onto the front lip of the unit base. Swing the
grille up into position.
3. Align cabinet and grill holes and secure, but do not overtighten
grille screws (1).
Removing and Installing Door Shelves
4. Install control knob (6) if equipped.
5. Reconnect power to the unit.
1
15 & 29 Models
1
3
2
2
6
75 Models
Typical Model Shown
For models equipped with door shelves:
To remove the door shelf:
6
1
1. Grasp shelf in center, and lift until the shelf notches (1) clear
the pins (2).
2. Carefully pull the shelf away from the door.
To install the door shelf:
1. Holding the shelf in the center, center the shelf in the door at
the desired location, slightly above the pins (2).
2
5
2. Lower the shelf onto the pins (2).
U-Line 1000 Series Maintenance
10
To reverse the door:
9 Standard Doors
Remove grille:
Remove the grille, see MAINTENANCE section of this guide.
Door Alignment and Adjustment
Align and adjust the door if it is not level, or is not sealing properly.
If the door is not sealed the unit may not cool properly, or
excessive frost may form in the interior.
IMPORTANT
Properly aligned, the door’s gasket should be firmly in
contact with the cabinet all the way around the door (no
gaps). Carefully examine the door’s gasket to assure that
it is firmly in contact with the cabinet. Also make sure the
door gasket is not pinched on the hinge side of the door.
To align and adjust the door:
1. Loosen (do not remove) top and bottom hinge screws.
2. Align door squarely with cabinet.
Remove top hinge, and door:
3. Make sure gasket is firmly in contact with cabinet all the way
around the door (no gaps).
1. Hold door to keep it from falling.
2. Remove top hinge from cabinet by removing three or four
screws, depending on model.
4. Tighten bottom hinge screws.
5. Tighten top hinge screws.
3. Remove door by tilting forward and lifting door off bottom
hinge.
Door Reversability
4. Remove three or four plastic screw plugs from hinge holes on
the opposite side. Reinstall into holes where the hinge was
removed. Ensure not to scratch cabinet.
Location of the unit may make it desirable to mount the door on
the opposite side of the cabinet.
Models with black and white doors are field-reversible.
Stainless steel models with glass doors without locks are
field-reversible.
Stainless steel models without glass doors must be ordered right-
or left-hand hinged.
Reversing the door
The hinge hardware will be removed and reinstalled on the
opposite side of the cabinet.
The hinge plate is flipped over when it is reinstalled on the
opposite side of the cabinet.
Remove bottom hinge:
1. Remove bottom hinge from cabinet. Some models will have a
gusset with two screws. Other models will have a plate with
three screws.
Plastic
Plug Hole
Plastic
Plug Hole
2. Remove corresponding screws on opposite side of cabinet. On
some models there may be a nut behind one or both screws on
either side.
Right Side
Left Side
Door Swing
Door Swing
15
U-Line Standard Door Alignment and Reversal
1
Install bottom hinge:
Prepare door for reinstallation:
For black or white doors:
1. If you have a plate hinge, reorient the pivot screw so it
protrudes the opposite direction form the hinge. Remove the
pivot screw from the hinge. Turn the plate over and reinstall
the screw.
1. Remove plastic hole plug from top of door handle and reinstall
on opposite side.
2. Align hinge outer edge with cabinet. For models with a plate
hinge, the flat edge of the hinge alignes with the outer edge of
the cabinet.
2. Remove plastic hinge bushing on bottom of door and reinstall on
opposite side. Clean out bushing hole in door bottom with a
screwdriver if necessary.
Install two or three screws, depending on model. Replace nuts if
used.
3
1
4
Install top hinge, and door:
2
1. Reorient the pivot screw so it protrudes the opposite
direction from the hinge. Remove the pivot screw from the
hinge. Turn the plate over and reinstall the screw.
2. Hold door to keep it from falling.
3. Lift the door on to the bottom hinge.
4. Align flat edge of the hinge with the outer edge of the unit.
5. Install three or four screws, depending on model.
Align and adjust the door:
Prepare door for reinstallation:
For stainless steel models with glass doors:
3. Stainless glass doors are flipped upside down to be reversed.
4. Lay the door on it’s side. Remove the plastic hole plug (1) and
install in the corner opposite of where it was removed.
1. Align and adjust the door, see DOOR ALIGNMENT AND
ADJUSTMENT.
5. Remove the plastic hinge bushing (2) and install in the corner
opposite of where it was removed.
Install grille:
6. Remove the U-Line nameplate (3) from door. This will reveal
mounting holes for the door actuator bracket.
Install the grille, see MAINTENANCE section of this guide.
7. Remove door actuator (4) from door. Be sure to only remove
the two screws holding the actuator to the door. Reinstall the
actuator (4) on the opposite end of the door where the
nameplate was removed.
8. Install new nameplate where the actuator assembly was
removed.
9. Install screws into holes on opposite side, where the hinge was
removed. Replace nuts if used.
U-Line Standrd Door Alignment and Reversal
16
7 Cleaning
Defrosting
Exterior Cleaning
Automatic Defrost Models
Vinyl Clad (Black or White) Models:
Frost on the rear wall is normal and will melt during each defrost
cycle. If there is excessive build-up of 1/4” or more, manually
defrost the unit.
•
Clean surfaces with a mild detergent and warm water solution.
Do not use solvent-based or abrasive cleaners. Use a soft
sponge and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
•
•
Ensure the door is closing and sealing properly.
High ambient temperature and excessive humidity can also
produce frost.
•
Clean any glass surfaces with a non-chlorine glass cleaner.
Stainless Models:
CAUTION
•
Stainless door panels, handles and frames can discolor when
exposed to chlorine gas, pool chemicals, saltwater or cleaners
with bleach.
DO NOT use an ice pick or other sharp instrument to
help speed up defrosting. These instruments can puncture
the inner lining or damage the cooling unit. DO NOT use
any type of heater to defrost. Using a heater to speed up
defrosting can cause personal injury and damage to the
inner lining.
•
Keep your stainless unit looking new by cleaning with a good
quality all-in-one stainless steel cleaner or polish monthly. For
best results use Claire® Stainless Steel Polish and Cleaner,
which can be purchased from U-Line Corporation (Part
Number 173348). Comparable products are acceptable.
Frequent cleaning will remove surface contamination that could
lead to rust. Some installations may require cleaning weekly.
IMPORTANT
The drain pan was not designed to capture the water
created when manually defrosting. To prevent water from
overflowing the drain pan, place towels or other absorbent
materials over the interior drain trough and under the
evaporator (1), before defrosting.
•
•
Do not clean with steel wool pads.
Do not use stainless steel cleaners polishes on any glass
surfaces.
•
Clean any glass surfaces with a non-chlorine glass cleaner.
•
Do not use cleaners not specifically intended for
stainless steel on stainless surfaces (this includes glass,
tile and counter cleaners).
•
If any surface discoloring or rusting appears, clean it quickly
with Bon-Ami® or Barkeepers Friend Cleanser® and a
nonabrasive cloth. Always clean towards the grain. Always finish
with Claire Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
1
•
Using abrasive pads such as Scotchbrite™ will cause
the graining in the stainless to become blurred.
•
Rust not cleaned up promptly can penetrate the surface of the
stainless steel and complete removal of the rust may not be
possible.
Interior Cleaning
•
Disconnect power to the unit.
To defrost:
•
Clean the interior and all removed components using a mild
nonabrasive detergent and warm water solution applied with a
soft sponge or non-abrasive cloth.
1. Disconnect power to the unit.
2. Remove all products from the interior.
3. Prop the door in an open position (2 in. (5 cm) minimum).
4. Allow the frost to melt naturally.
•
•
Rinse the interior using a soft sponge and clean water.
Do not use any solvent-based or abrasive cleaners.
These types of cleaners may transfer taste to the interior
products and damage or discolor the interior.
5. After the frost melts completely clean the interior and all
removed components. (See INTERIOR CLEANING)
6. When the interior is dry, reconnect power and turn unit on.
13
U-Line 1000 SeriesCleaning
Condensor Cleaning
Storage, Vacation and Moving
Interval - Every Three Months
If not using the unit for an extended period, or otherwise stored,
follow these steps completely:
To maintain operational efficiency, keep the front grille free of dust
and lint, and clean the condenser every three months. Depending
on environmental conditions, more or less frequent cleaning may
be necessary.
WARNING
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels. Failure
to do so may result in death or electrical shock.
WARNING
Disconnect electric power to the unit before cleaning
the condenser.
IMPORTANT
If the ambient temperature is expected to drop below
50°F, turn off and unplug unit, and drain all water from the
unit to prevent freezing damage not covered by the
warranty.
WARNING
DO NOT touch the condenser fins. The condenser fins
are SHARP and can be easily damaged.
1. Remove all consumable contents from the unit.
2. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
IMPORTANT
DO NOT use any type of cleaner on the condenser unit.
1. Remove the grill. (See MAINTENANCE)
3. Clean and dry the interior of the cabinet.
4. During periods of nonuse, the cabinet must remain open to
prevent formation of mold and mildew. Open door a minimum
of 2 in. (5 cm) to provide the necessary ventilation.
2. Clean the condenser coil (4) using a using a soft brush with a
“combing” action or vacuum cleaner. Do not touch the
condenser coil.
3. Install the grill. (See MAINTENANCE)
Product Disposal
29 Models
If the unit is being removed from service for disposal, check and
obey all Federal, State and or Local regulations regarding the
disposal and recycling of refrigeration appliances, and follow these
steps completely:
Typical Model Shown
4
1. Remove all consumable contents from the unit.
2. Disconnect power to the unit and unplug the power cord from
its outlet.
DANGER
RISK OF CHILD ENTRAPEMENT. Before you throw away
your old refrigerator or freezer, take off the doors and leave
shelves in place so children may not easily climb inside.
75 Models
Typical Model Shown
3. Remove the cabinet door.
4
U-Line 1000 Series Cleaning
14
8 Service
Before Calling for Service
Troubleshooting Guide
If you think your U-Line product is malfunctioning, read the
OPERATION section of this guide to clearly understand the
function of the control.
DANGER
ELECTROCUTION HAZARD. Never attempt to repair or
perform maintenance on the unit until disconnecting the
main electrical power.
If the problem persists, read the NORMAL OPERATING
SOUNDS and TROUBLESHOOTING GUIDE section of this guide
to help you quickly identify common problems, and possible causes
and remedies. Most often, this will resolve the problem without
the need to call for service.
Troubleshooting - What to check when problems occur:
Problem
Possible Cause and Remedy
Interior Light
Does Not
The light bulb may be defective.(See MAINTENACE)
If Service is Required
Illuminate.
If you do not understand a troubleshooting remedy, or your
product needs service, contact U-Line Corporation directly.
Contact information appears on the rear cover of this guide.
Light Remains
on When Door
is Closed.
Turn off light switch if equipped (See OPERATION)
Adjust light actuator bracket on bottom of door.
When you call, you will need your product Model and Serial
Numbers. This information can be recorded inside the front cover
of this guide. It also appears on the Model and Serial number plate
located on the upper right or rear wall of the interior of your
product.
Unit Develops
Frost on
Internal
Frost on the rear wall is normal and will melt during
each off cycle.
If there is excessive build-up of 1/4” or more,
manually defrost the unit.
Surfaces.
Ensure the door is closing and sealing properly.
High ambient temperature and excessive humidity
can also produce frost.
Replacement Parts
Unit Develops
Condensation
on External
surfaces
The unit is exposed to excessive humidity, moisture
will dissipate as humidity levels decrease.
When you need replacement parts, always request genuine U-Line
replacements. U-Line designs and engineers products using
components that work efficiently, and provide superior service life
and performance. The use of aftermarket parts or components
may affect the safety, operation, performance or durability of your
product, and may also void its warranty.
Product is
Freezing.
Product in contact with the rear wall may freeze,
ensure no product is touching the rear wall.
Adjust the temperature to a warmer set-point. (See
OPERATION)
Product is Not
Cold Enough.
Air temperature does not indicate product
temperature. See OPERATION - Checking Product
Temperature .
Adjust the temperate to a cooler set-point. (See
OPERATION)
Ensure unit is not located in excessive ambient
temperatures or in direct sunlight.
Ensure the door is closing and sealing properly.
Normal Operating Sounds
All models incorporate rigid foam insulated cabinets to provide
high thermal efficiency and maximum sound reduction for its
internal working components. Despite this technology, your model
may make sounds that are unfamiliar.
Ensure the interior light has not remained on too
long.
Ensure nothing is blocking the front grille, found at
the bottom of the unit.
Ensure the condensor coil is clean and free of any dirt
or lint build-up.
Normal operating sounds may be more noticeable because of the
unit’s environment. Hard surfaces such as cabinets, wood, vinyl or
tiled floors and paneled walls have a tendency to reflect normal
appliance operating noises.
Listed below are common refrigeration components with brief
description of the normal operating sounds they make. NOTE:
Your product may not contain all the components listed.
•
Compressor: The compressor makes a hum or pulsing sound
that may be heard when it operates.
•
Evaporator: Refrigerant flowing through an evaporator may
sound like boiling liquid.
•
•
Condenser Fan: Air moving through a condenser may be heard.
Automatic Defrost Drain Pan: Water may be heard dripping or
running into the drain pan when the unit is in the defrost cycle.
15
U-Line 10 Series Service
USE AND CARE GUIDE
®
PRODUCT INFORMATION
Complete Installation Guides, Use and Care Guides, Specifications & Features and Benefits, CAD Drawings,
Overlay Panel/Frame and Toe-Kick Specifications and Instructions, Compliance Documentation and Applicable
Energy Guides are available for reference and download at u-line.com.
SERVICE INFORMATION
Please consult your Use and Care Guide for troubleshooting information. Answers to Customer Frequently Asked
Questions are available at u-line.com under Customer Service. You may contact U-Line directly:
GENERAL INQUIRIES:
U-Line Corporation
SERVICE ASSISTANCE:
Phone 1-800-779-2547
P.O. Box 245040
FAX 1-414-354-5696
Milwaukee, Wisconsin 53224-9540 U.S.A.
Phone 1-414-354-0300
FAX 1-414-354-7905
Email: [email protected]
u-lineservice.com
Email: [email protected]
u-line.com
PARTS ASSISTANCE:
E-mail: [email protected]
BUILDING ON THREE GENERATIONS OF INNOVATION
For nearly five decades and three generations, U-Line continues to be the leader in innovation, quality and value in
the premium built-in undercounter ice making, refrigeration and wine preservation market. U-Line has captivated
those with an appreciation for the finer things with exceptional functionality, style, inspired innovation and attention
to even the smallest details. We are known and respected for our unwavering dedication to product design, quality
and selection.
In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was the first
to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and determination
to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The newest
Uihlein generation continues to build upon the family’s innovative legacy at the Milwaukee, Wisconsin based business
by providing continuity and vision from which new designs and technology continue to be born.
®
®
Today the complete U-Line product collection includes Ice Makers, Wine Captain Models, Combo Models,
a Refrigerator / Freezer, Refrigerators, Drawers and Beverage Centers. The U-Line brand offers products in the
1000 Series, 2000 Series and the Modular 3000 Series. The 1000 Series offers a more targeted priced product with
appropriate features, while the 2000 Series offers upscale features, advanced technology and specialized product
families. U-Line’s approach to its breadth of products, multiple price points and features allows a choice and
product that will fit any lifestyle.
DESIGNED, ENGINEERED AND ASSEMBLED IN WISCONSIN, USA
The Built-In Undercounter Leader Since 1962
U-LINE.COM
©2009 U-Line Corporation
Publication Number 30263 07/2012 Rev. G
|