Turbosound Speaker TQ 308DP User Manual

QLIGHTDP  
DIGITAL POWER SERIES  
USER MANUAL  
TQ-308DP  
TQ-310DP  
TQ-315DP  
TQ-445DP  
TQ-425DP  
TQ-115DP  
Turbosound Ltd.  
Star Road, Partridge Green  
West Sussex RH13 8RY United Kingdom  
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155  
Issue 1.3 July 2006  
Copyright © 2006 Turbosound Ltd.  
 
user manual  
QLight™ DP series  
CONTENTS  
Important Safety Information ................................................................................................................. 5  
Important Safety Information ............................................................................................................ 6  
Introduction.............................................................................................................................................. 7  
Thanks ................................................................................................................................................. 7  
Unpacking the TQ series loudspeaker ............................................................................................... 7  
Features.................................................................................................................................................... 8  
Product Range Summary........................................................................................................................ 9  
TQ-308DP self-powered two-way loudspeaker ................................................................................. 9  
TQ-310DP self-powered two-way loudspeaker ................................................................................. 9  
TQ-308DP and TQ-310DP connector panel functions ..................................................................... 10  
TQ-315DP self-powered two way loudspeaker ............................................................................... 11  
TQ-445DP self-powered three-way loudspeaker............................................................................. 11  
TQ-315DP and TQ-445DP connector panel functions ..................................................................... 12  
TQ-425DP self-powered subwoofer................................................................................................. 13  
TQ-115DP self-powered subwoofer................................................................................................. 13  
TQ-425DP connector panel functions .............................................................................................. 14  
TQ-115DP connector panel functions .............................................................................................. 15  
System Requirements........................................................................................................................... 16  
System requirements – TQ-308DP, TQ-310DP and TQ-315DP ....................................................... 16  
System requirements – TQ-445DP................................................................................................... 16  
System requirements – TQ-425DP and TQ-115DP.......................................................................... 16  
Amplifier Modules................................................................................................................................. 17  
Power Amplifiers .............................................................................................................................. 17  
AC Power Requirements .................................................................................................................. 17  
Cooling .............................................................................................................................................. 17  
Audio Input........................................................................................................................................ 17  
Limiting Functions ............................................................................................................................ 18  
Limit LED Functions.......................................................................................................................... 18  
Mode A / Mode B switch .................................................................................................................. 19  
Updating firmware or loudspeaker parameters.............................................................................. 19  
Equalisation ........................................................................................................................................... 19  
Converging Elliptical Waveguides..................................................................................................... 20  
Mounting and Fixing ............................................................................................................................. 21  
Rigging Hardware............................................................................................................................. 21  
Permanent Installations.................................................................................................................... 24  
Choosing the best location............................................................................................................... 24  
Maintenance .......................................................................................................................................... 26  
QLight DP series manual  
page 3  
 
user manual  
QLight™ DP series  
Removal of the low frequency driver – TQ-308DP, TQ-310DP, TQ-315DP .....................................26  
Removal of the HF unit – TQ-308DP, TQ-310DP ..............................................................................26  
Removal of the 12”/1” driver – TQ-445DP........................................................................................26  
Removal of the midrange unit – TQ-445DP......................................................................................27  
Removal of the low frequency driver – TQ-425DP...........................................................................27  
Removal of the low frequency driver – TQ-115DP...........................................................................27  
Removal of the amplifier module – all models................................................................................28  
Appendix A: Spares and accessories....................................................................................................29  
Flying accessories..............................................................................................................................29  
Appendix B: Technical Specifications...................................................................................................30  
Appendix B: Technical Specifications...................................................................................................30  
Appendix C: Warranty............................................................................................................................32  
Limited Warranty...............................................................................................................................32  
Warranty Coverage ...........................................................................................................................32  
Shipping.............................................................................................................................................32  
QLight DP series manual  
page 4  
 
user manual  
QLight™ DP series  
An example of this equipment has been tested and found to comply with the  
following European and international Standards for Electromagnetic Compatibility  
and Electrical Safety:  
EN60065  
Product safety  
EN55103-1  
EN55103-2  
Electromagnetic emission  
Electromagnetic immunity  
IMPORTANT SAFETY INFORMATION  
Do not remove Covers. There are no user serviceable parts inside, please refer servicing to  
qualified service personnel. This equipment must be earthed.  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
DO NOT EXPOSE TO RAIN OR MOISTURE  
ATTENTION  
RISQUE DE CHOC ELECTRIQUE  
NE PAS ENLEVER  
NE PAS EXPOSER A LA PLUIE NI A L’HUMITE  
QLight DP series manual  
page 5  
 
user manual  
QLight™ DP series  
Important Safety Information  
Please read carefully and keep the following instructions and safety information. Heed all  
warnings and follow all instructions.  
Do not remove covers. There are no user serviceable parts inside, please refer servicing to  
qualified service personnel. This equipment must be earthed.  
Do not block any of the ventilation openings. Install in accordance with manufacturer’s  
instructions.  
Clean only with a damp cloth.  
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two  
blades with one wider than the other. A grounding type plug has two blades and a third grounding  
prong. The wide blade or the third prong is provided for your safety. When the provided plug does  
not fit into your outlet, consult an electrician for replacement of the obsolete outlet.  
Protect the power cord from being walked on or pinched particularly at plugs, convenience  
receptacles, and the point where they exit from the apparatus.  
Only use attachments/accessories specified by the manufacturer.  
Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with the  
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid  
injury from tip-over.  
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has  
been damaged in any way, such as the power supply cord or plug is damaged, liquid has been  
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or  
moisture, does not operate normally, or has been dropped.  
QLight DP series manual  
page 6  
 
user manual  
QLight™ DP series  
INTRODUCTION  
Thanks  
Thank you for choosing a QLight™ series loudspeaker product for your application. Please spare a  
little time to read the contents of this manual, so that you can obtain the best possible  
performance from this unit.  
All TURBOSOUND products are carefully engineered for world-class performance and reliability.  
If you would like further information about this or any other TURBOSOUND product, please  
We look forward to helping you in the near future.  
Congratulations, you have just purchased a professional loudspeaker system from the renowned  
Turbosound range, designed to give you the best in audio quality and many years of reliable,  
trouble free operation. It offers superior audio quality, unsurpassed vocal projection, full technical  
documentation including EASE data, and comprehensive rigging and flying hardware options.  
Please read through this manual carefully before you attempt to operate the loudspeaker system.  
It contains valuable information enabling you to quickly and easily set up and connect the  
loudspeakers, important system and set-up checks together with positioning and mounting  
instructions.  
Unpacking the TQ series loudspeaker  
After unpacking the unit please check carefully for damage. If damage is found, please notify the  
carrier concerned at once. You, the consignee, must instigate any claim. Please retain all  
packaging in case of future re-shipment.  
QLight DP series manual  
page 7  
 
user manual  
QLight™ DP series  
FEATURES  
Superb audio quality: carefully designed and matched loudspeaker drive units are used to  
give you exceptional performance and many years of reliable, trouble free operation.  
Class D amplifiers with 96kHz DSP: operating efficiency in excess of 90% gives higher  
performance, reduced weight and less wasted heat.  
Converging Elliptical Waveguide: used in TQ-308DP, TQ-310DP and TQ-315DP  
loudspeakers eliminates reflections in the horn throat and gives excellent pattern control.  
Controlled dispersion: the TQ-445DP exhibits a tightly controlled dispersion pattern which  
minimises room reflections and focuses the sound pressure directed at audience areas.  
Rotatable HF waveguides: high frequency waveguides used in the TQ-308DP, TQ-310DP  
and TQ-315DP are designed to accommodate 90° rotation within the enclosure to allow for  
horizontal or vertical orientation.  
Ease of use: QLight™ DP series products are exceptionally easy to set up and use with the  
minimum of technical knowledge required. The built-in digital amplifiers require only a  
mains connection and balanced signal input for correct operation.  
Three-way design: the TQ-445DP’s exclusive use of cone transducers in the low and mid  
frequency bands guarantees a seamless low/mid crossover, greater power handling, lower  
distortion and minimal mechanical stress.  
Mode A / Mode B response: user-selectable frequency response profiles are provided to  
suit specific applications such as use with or without subs.  
Aligned components: low and high frequency components are physically aligned in the  
enclosure to ensure perfect time arrival at the listener’s ear; TQ-445DP components are  
aligned within the on-board DSP.  
Solid construction: QLight™ DP series cabinets are built from high-grade birch plywood,  
rebated, screwed and glued together for maximum rigidity and durability.  
Integral rigging points: fitted as standard, enabling use with optional Turbosound flying  
hardware for fixed installations and mobile sound reinforcement applications.  
Compact enclosures: the overall dimensions of QLight™ DP series enclosures have been  
kept as small as possible to enable portable use as well as fitting easily into permanent  
installations.  
QLight DP series manual  
page 8  
 
user manual  
QLight™ DP series  
PRODUCT RANGE SUMMARY  
TQ-308DP self-powered two-way loudspeaker  
The TQ-308DP is a compact trapezoidal self-powered two-way loudspeaker enclosure with an  
integral Class D amplifier and DSP module, designed for use in mobile speech and music sound  
reinforcement applications as well as a range of fixed installations. It incorporates two channels of  
digital power amplification with 96kHz DSP into one convenient and easily transportable package.  
The TQ-308DP delivers high quality full range audio from an unobtrusive and easily transportable  
package, and can be set up and operated quickly and with consistently repeatable results.  
The TQ-308DP combines an 8” LF driver with a 1” HF compression driver on a rotatable 100º x 60º  
high frequency waveguide in a compact trapezoidal cabinet, making it possible to swap the  
horizontal and vertical coverage patterns. It features Turbosound’s Converging Elliptical  
Waveguide™ (CEW™) technology which provides smooth and even coverage of a room.  
All connections and operating controls are located on a recessed panel at the rear of the cabinet,  
including gain trim, low frequency contour, power switch and status LED’s. The loudspeaker  
accepts a balanced input from an audio mixer on a 3-pin XLR, and a parallel link connection is  
provided to connect to additional powered loudspeakers. The power supply is auto-sensing, which  
allows the TQ-308DP to be connected to mains supplies ranging from 100 volts to 230 volts AC.  
The module is fully field-serviceable simply by removing four bolts and a multi-pin connector. An  
RS232 data port is provided to enable firmware upgrades.  
TQ-310DP self-powered two-way loudspeaker  
The TQ-310DP is a trapezoidal self-powered two-way loudspeaker enclosure designed for use in  
mobile speech and music sound reinforcement applications, as well as in a wide range of fixed  
installations.  
The loudspeaker complement consists of a front loaded 10” low frequency driver and a 1” high  
frequency compression driver on a rotatable 100°H x 60°V HF Converging Elliptical Waveguide.  
The TQ-310DP features Turbosound’s Converging Elliptical Waveguide™ (CEW™) technology. The  
comparatively short flare allows physical alignment of the HF and LF devices, and ensures that the  
wavefront is shaped smoothly, eliminating reflections in the throat area while giving excellent  
pattern control. Additionally this design does not suffer from the distortion typical of horns  
employing diffraction edges. The waveguide can be rotated within the enclosure, making it  
possible to swap the horizontal and vertical coverage patterns.  
QLight DP series manual  
page 9  
 
user manual  
QLight™ DP series  
TQ-308DP and TQ-310DP connector panel functions  
Model No TQ-308DP  
123456  
Serial No  
Star Road, Partridge Green, West Sussex, RH13 8RY England  
tel:+44 (0)1403 711447 fax:+44 (0)1403 710155 www.turbosound.com  
CAUTION  
ATTENTION  
Limit HI  
Limit LO  
Power  
10  
9
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
RISQUE DO CHOC ELECTRIQUE  
NE PAS ENLEVER  
DO NOT EXPOSE TO  
RAIN OR MOISTURE  
NE PAS EXPOSER LA  
A
PLUIE NI L'HUMIDITE  
A
space  
for  
ETL & ETLc  
logo  
CAUTION to reduce the risk of fire replace only with same  
type and rating of fuse.  
AVIS utiliser un fusible de rechange de meme type.  
8
THIS EQUIPMENT MUST BE EARTHED  
MODE  
FUSE  
T10AL 250V  
115-230V  
1000VA  
50-60Hz  
WITH SUB NO SUB  
(speech)  
INPUT  
LINK  
AUX  
(music)  
1
2
3
4
5
6
7
1. Signal input – lockable 3-pin XLR line input socket connects to audio mixer. Fully balanced,  
pin 2 Hot, pin 3 Cold and pin 1 not connected.  
2. Signal link – lockable 3-pin XLR line output socket links to additional cabinets. Fully  
balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.  
3. Mode switch – used to change the low frequency tuning when used with QLight™ series  
subwoofers or for stand-alone operation.  
4. Aux – RS232 port used for updating settings or firmware.  
5. Fuse – AC line fuse. Replace only with 10A 230V anti-surge fuse.  
6. Mains switch – turns AC power on to the unit.  
7. AC mains connection - accepts Neutrik PowerCon® 3-pin cable-end connector.  
8. Power - Blue LED indicates when AC power is applied to the amplifier module.  
9. Limit (low) – red LED indicates limiting threshold of the low frequency section.  
10. Limit (high) – red LED indicates limiting threshold of the mid/high frequency section.  
QLight DP series manual  
page 10  
 
user manual  
QLight™ DP series  
TQ-315DP self-powered two way loudspeaker  
The TQ-315DP offers full range response and the highest performance from a two-way  
loudspeaker. The integrated Class D amplifiers and DSP ensure an optimum match between  
amplifiers and drive units, providing a convenient and easily transportable package.  
It incorporates a 15” LF driver and a 1.4” exit (3” diaphragm) compression driver on an 80° x 50°  
Converging Elliptical Waveguide in an optimally ported trapezoidal enclosure.  
All connections and operating controls are located on a recessed panel at the rear of the cabinet,  
including gain trim, low frequency contour, power switch and status LED’s. The loudspeaker  
accepts a balanced input from an audio mixer on a 3-pin XLR, and a parallel link connection is  
provided to connect to additional powered loudspeakers. The power supply is auto-sensing, which  
allows the TQ-308DP to be connected to mains supplies ranging from 100 volts to 230 volts AC.  
The module is fully field-serviceable simply by removing four bolts and a multi-pin connector. An  
RS232 data port is provided to enable firmware upgrades.  
TQ-445DP self-powered three-way loudspeaker  
The TQ-445DP is a compact three-way self-powered full range enclosure including integral Class D  
power amplifiers and digital signal processing. The use of Class D power amplifier technology  
ensures an exact match between amplifier and speaker for optimum acoustic output, and offers  
exceptional ease of use by combining the entire electro-acoustic system in one convenient, easily  
transportable physical package with negligible additions to the cabinet weight.  
It incorporates a custom-designed co-axial 12"/1" combination LF/HF driver in an optimally tuned  
vented trapezoidal enclosure handling the low and high frequency bands. The critical mid-range  
frequencies are handled by a proprietary 6.5" cone transducer on a 60° horizontal by 40° vertical  
nominal dispersion waveguide, loaded with a TurboMiddevice.  
The exclusive use of cone transducers in both the low and mid frequency bands produces a  
seamless transition at the crossover frequency, with the result that all of the critical vocal range  
right up to 8kHz is lower in distortion than compression driver-based designs. In addition the 6.5"  
mid-range driver is a highly efficient device, and is able to handle large amounts of amplifier  
power.  
The TQ-445DP is a full range loudspeaker, and used by itself will provide high quality audio for all  
speech and many music reproduction applications. In order to extend the effective bass frequency  
range of the loudspeaker by a further octave the use of the complementary TQ-425DP subwoofer  
is recommended.  
QLight DP series manual  
page 11  
 
user manual  
QLight™ DP series  
TQ-315DP and TQ-445DP connector panel functions  
1
2
3
4
5
6
7
8
9
10  
1. AUX connection – RS232 port used for updating settings or firmware.  
2. Signal link – lockable 3-pin XLR line input socket connects to audio mixer. Fully balanced,  
pin 2 Hot, pin 3 Cold and pin 1 not connected.  
3. Signal link – lockable 3-pin XLR line output socket connects to additional cabinets. Fully  
balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.  
4. Mode switch – used to change the low frequency tuning when used with QLight™ series  
subwoofers or for stand-alone operation.  
5. Power – blue LED indicates when AC power is applied to the amplifier module.  
6. Limit (low) – red LED used to indicate LF limiting, self test and protection.  
7. Limit (high) – red LED used to indicate MF/HF limiting, self test and protection.  
8. Fuse – AC line fuse. Replace only with 10A 230V anti-surge fuse.  
9. Power – Blue LED indicates when AC power is applied to the unit.  
10. AC Mains connection – accepts Neutrik PowerCon® 3-pin cable-end connector.  
QLight DP series manual  
page 12  
 
user manual  
QLight™ DP series  
TQ-425DP self-powered subwoofer  
The TQ-425DP is a self-powered dual 15” subwoofer designed for use with QLight™ series self-  
powered enclosures and when combined with the TQ-445DP it forms a formidable full-range  
sound reinforcement system with high SPL and negligible distortion.  
Each of the high power neodymium 15” drive units are powered by an independent amplifier  
channel in order to preserve the maximum headroom capability and to ensure an optimum match  
with the drive units. The Class D amplifier module is located at the rear of the cabinet, removable  
for servicing, and carries all the necessary connections and operating controls.  
The TQ-425DP can be permanently installed using flying strips which attach to the rigging points  
provided on the sides of the cabinet. In addition it is fitted with a pole mount socket that allows  
QLight™ series enclosures to be mounted on top at an optimum height.  
TQ-115DP self-powered subwoofer  
The TQ-115DP is a self-powered single 15” subwoofer designed for use with QLight™ series self-  
powered enclosures. It is particularly effective when combined with TQ-308DP and TQ-310DP  
loudspeakers to form a high quality full range and compact sound reinforcement system.  
Its Class D amplifier module is situated at the rear of the cabinet and offers XLR input and parallel  
link connections, Neutrik PowerCon® AC mains connection and power switch, as well as system  
status LEDs. The auto-switching power supply allows the unit to be connected to AC mains outlets  
ranging from 100 volts to 230 volts.  
The TQ-115DP can be permanently installed using flying strips which attach to the rigging points  
provided on the sides of the cabinet. In addition it is fitted with a pole mount socket that allows  
QLight™ series enclosures to be mounted on top at an optimum height.  
QLight DP series manual  
page 13  
 
user manual  
QLight™ DP series  
TQ-425DP connector panel functions  
7
8
PUSH  
1
2
3
4
5
6
7
1. Aux – RS232 port used for updating settings or firmware.  
2. Gain control – gain trim control ranges from +6dB to -6dB  
3. Signal input – lockable 3-pin XLR line input socket connects to audio mixer. Fully balanced,  
pin 2 Hot, pin 3 Cold and pin 1 not connected.  
4. Signal link – lockable 3-pin XLR line output socket links to additional cabinets. Fully  
balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.  
5. Mains switch – turns AC power on to the unit.  
6. Fuse – AC line fuse. Replace only with 10A 230V anti-surge fuse.  
7. AC mains connection - accepts Neutrik PowerCon® 3-pin cable-end connector.  
8. Limit – red LED indicates limiting threshold.  
9. Power - Blue LED indicates when AC power is applied to the amplifier module.  
QLight DP series manual  
page 14  
 
user manual  
QLight™ DP series  
TQ-115DP connector panel functions  
Model No TQ-115DP  
123456  
Serial No  
Star Road, Partridge Green, West Sussex, RH13 8RY England  
tel:+44 (0)1403 711447 fax:+44 (0)1403 710155 www.turbosound.com  
CAUTION  
ATTENTION  
Limit HI  
Limit LO  
Power  
10  
9
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
RISQUE DO CHOC ELECTRIQUE  
NE PAS ENLEVER  
DO NOT EXPOSE TO  
RAIN OR MOISTURE  
NE PAS EXPOSER LA  
A
PLUIE NI A L'HUMIDITE  
space  
for  
ETL & ETLc  
logo  
CAUTION to reduce the risk of fire replace only with same  
type and rating of fuse.  
AVIS utiliser un fusible de rechange de meme type.  
8
THIS EQUIPMENT MUST BE EARTHED  
MODE  
FUSE  
T10AL 250V  
115-230V  
1000VA  
50-60Hz  
WITH SUB NO SUB  
INPUT  
LINK  
(speech)  
(music)  
AUX  
1
2
3
4
5
6
7
1. Signal input – lockable 3-pin XLR line input socket connects to audio mixer. Fully balanced,  
pin 2 Hot, pin 3 Cold and pin 1 not connected.  
2. Signal link – lockable 3-pin XLR line output socket links to additional cabinets. Fully  
balanced, pin 2 Hot, pin 3 Cold and pin 1 not connected.  
3. Mode switch – lifts the overall gain of the subwoofer by 3dB.  
4. Aux – RS232 port used for updating settings or firmware.  
5. Fuse – AC line fuse. Replace only with 10A 230V anti-surge fuse.  
6. Mains switch – turns AC power on to the unit.  
7. AC mains connection - accepts Neutrik PowerCon® 3-pin cable-end connector.  
8. Power - Blue LED indicates when AC power is applied to the amplifier module.  
9. Limit (low) – red LED indicates limiting threshold of the low frequency section.  
QLight DP series manual  
page 15  
 
user manual  
QLight™ DP series  
SYSTEM REQUIREMENTS  
System requirements – TQ-308DP, TQ-310DP and TQ-315DP  
These products are two-way self-powered loudspeaker systems. They comprise two independent  
amplifier channels: one channel to power the low frequency driver (LF) plus another channel to  
power the high frequency (HF) driver; plus an active crossover to split the signal and feed it to the  
appropriate amplifier and driver section. Additional features such as limiting, digital time  
alignment and driver EQ are carried out in the on board DSP. These products do not require the  
use of external amplifiers or crossover/limiters.  
Additional units may be daisy-chained together simply by linking the signal connections through  
the input / link XLR connectors. In this way exact coverage of an event or permanent installation  
may be achieved using a number of digitally powered loudspeakers. It is however necessary to  
route individual power cords to each enclosure as it is not possible to daisy-chain AC connections  
through the power connectors.  
System requirements – TQ-445DP  
The TQ-445DP is a three-way self-powered loudspeaker system. It comprises two independent  
amplifier channels: one channel to power the low frequency driver (LF) plus another channel to  
power the high frequency midrange (MF) and high frequency (HF) together; plus a frequency  
dividing network to split the signal and feed it to the appropriate driver section. Additional  
features such as limiting, digital time alignment and driver EQ are carried out in the on board DSP.  
The TQ-445DP does not require the use of external amplifiers or crossover/limiters.  
Additional units may be daisy-chained together as above to achieve exact coverage of an event or  
permanent installation using a number of digitally powered loudspeakers.  
System requirements – TQ-425DP and TQ-115DP  
These products are self-powered subwoofer systems designed to accompany QLight™ series self-  
powered loudspeakers. The TQ-425DP comprises two independent amplifier channels: one  
channel to power each low frequency driver. The TQ-115DP uses one amplifier channel to power  
the single drive unit.  
Additional units may be daisy-chained together as above to achieve exact coverage of an event or  
permanent installation using a number of digitally powered loudspeakers.  
QLight DP series manual  
page 16  
 
user manual  
QLight™ DP series  
AMPLIFIER MODULES  
Power Amplifiers  
The digital power amplifiers used in QLight™ DP series loudspeakers are conservatively rated and  
designed with sufficient headroom to handle large signal transients without break-up or distortion.  
Each channel of the module will deliver 800 watts r.m.s. into an 8 ohm load.  
AC Power Requirements  
QLight™ DP series loudspeakers are equipped with Neutrik PowerCon® AC mains connectors  
which mate with the power cord supplied with your unit. They operate with mains voltages in the  
range from 100 to 240 volts. When connected to a mains supply the digital power amplifier  
modules will automatically detect the mains supply present. The mains fuse is a 10A 20mm 230V  
anti-surge type for all mains supplies. Should it be necessary always replace the fuse with the  
identical size and type.  
Cooling  
The Class D amplifiers are among the most efficient in their class, with operating efficiencies  
greater than 90%. Conventional heatsinks are not required to cool the amplifiers; they are cooled  
by the action of convection from the panel of the amplifier module at the rear of the enclosure. It is  
important to leave space around and especially above the rear panel to allow the convection of  
heat away from the loudspeaker. This cooling effect is sufficient to maintain the amplifiers within a  
normal operating temperature range.  
In an ambient temperature of 25º C the rear panel of the unit can reach temperatures of 55º C and  
will feel warm to the touch. This is perfectly acceptable and is considered normal operation.  
Audio Input  
The signal inputs are fully balanced, with an input impedance of 10k. The female input XLR  
connector is wired pin 2 hot (+ve), pin 3 cold (-ve), and pin 1 screen (shield). The male link XLR  
connector is wired pin 2 hot (+ve), pin 3 cold (-ve), and pin 1 not connected. Multiple self-powered  
enclosures may be driven from a single audio console, up to a practical limit of 16 units. A greater  
number may cause unacceptable signal loss due to the loading of the console output.  
QLight DP series manual  
page 17  
 
user manual  
QLight™ DP series  
Limiting Functions  
The amplifier modules are equipped with accurate limiters for both high frequency and low  
frequency sections. Because the HF and LF limiters work independently of each other, there is no  
possibility of either section compromising the performance of the other as is the case with a single  
broad-band limiter. Furthermore, each limiter has its attack and release time constants  
independently set and optimised according to the operating frequency range. These allow  
transient delivery whilst preventing overheating or over excursion of the transducers.  
Limit LED Functions  
At switch-on the power LED will illuminate and the red limit LED’s will flash in unison for  
approximately 5 seconds as the unit performs an initial diagnostic self-test. Audio will be  
automatically muted during this period.  
After initialisation, the limit LED’s extinguish and the unit will now pass audio. During operation if  
either of the red limit LEDs flash this indicates that the DSP is taking corrective action by applying  
the limiter to that channel in order to avoid damage to the drive unit. You should reduce the signal  
accordingly so that the limit LED’s light only occasionally. Both LED’s flashing in unison under  
regular operating conditions indicates that the DSP is activating a protection feature, taking two  
possible courses of action: the input will either be attenuated to stop the unit being overdriven, or  
in extreme cases will be shut down.  
Status  
Condition  
Action  
Both Limit LED’s flashing  
Both Limit LED’s flashing  
Limit high LED flashing  
System initialisation  
Protection activated  
Reduce input level  
DSP applying limiting to the Reduce input level  
high frequency channel  
Limit low LED flashing  
DSP applying limiting to the low Reduce input level  
frequency channel  
1 WARNING 1  
The limiters are designed to allow short-term transients in program material in order to preserve  
sufficient dynamic headroom, while at the same time optimising component life by protecting  
against long-term heating effects. DO NOT allow the loudspeaker to constantly run into limiting;  
this will not only degrade your sound quality by reducing the available dynamic range, but also in  
extreme cases may increase the risk of damage to the drive units.  
QLight DP series manual  
page 18  
 
user manual  
QLight™ DP series  
Mode A / Mode B switch  
This rear panel switch modifies the overall response of the system in order to give you optimised  
profiles for differing applications.  
When the Mode A position is selected, the low frequency section is extended down to a nominal  
cut-off frequency of 35Hz, which makes the loudspeakers balanced for full range reproduction of a  
wide range of music. The low frequency extension is achieved by using low shelf @ 90Hz.  
When the Mode B position is selected, the response of the system will exhibit a reduced low  
frequency. This roll-off setting is specially designed for use with Turbosound QLight™ DP  
subwoofers. This restricted LF response is also useful in speech applications where reduced LF  
levels can lead to better vocal intelligibility.  
Updating firmware or loudspeaker parameters  
Periodically Turbosound will release updated settings to improve the performance of your  
loudspeaker system. Your local Turbosound dealer will be able to give you the latest settings.  
These are released with comprehensive instructions on how to upgrade your units.  
NOTE: When updating firmware both Limit LED’s will light continuously while the download is  
taking place. Both LED’s will operate normally during a settings upload.  
EQUALISATION  
QLight™ series enclosures are designed to provide smooth and even frequency response. They do  
not need excessive amounts of external equalisation to overcome the sonic deficiencies often  
found in many lesser designs.  
Should an extended frequency response be required at more than moderate sound pressure  
levels, the use of complementary QLight™ subwoofer enclosures is strongly recommended.  
In order to compensate for the room acoustics, QLight™ series enclosures require only minimal  
equalisation. As in any system, over-equalisation introduces phase shifts, distortion and a  
reduction in headroom, usually causing more problems than it cures. Under most circumstances a  
1/3 or 1/2 octave graphic equaliser will generally be adequate, with the fader settings applied  
smoothly and as little as possible for the required room compensation. Most rooms will have  
resonances that will be excited at particular frequencies needing some cut to help tame the sound.  
These problems are most pronounced at the lower frequencies where loudspeakers generally  
exhibit very little directional control. If you find that the system needs a lot of boost at lower  
frequencies you may need additional sub-bass units. It is good practice to use as little equalisation  
as possible, aiming to cut frequencies rather than adding large amounts of boost.  
QLight DP series manual  
page 19  
 
user manual  
QLight™ DP series  
CONVERGING ELLIPTICAL WAVEGUIDES  
A design feature of the TQ-308DP, TQ-310DP and TQ-315DP loudspeakers is the Converging  
Elliptical Waveguide(CEW). This gives many user advantages. The comparatively short flare  
length allows the HF and LF components to be physically aligned in the cabinet, so ensuring  
coherent arrival at the listener’s ear irrespective of distance from the loudspeaker. The elliptical  
format shapes the wavefront smoothly, and eliminates reflections in the throat area. Additionally  
this design does not suffer from the distortion typical of horns employing diffraction edges.  
The waveguides can be removed and rotated through 90º in the cabinet, which allows the  
products to be installed in either vertical or horizontal formats while retaining the required  
coverage.  
QLight DP series manual  
page 20  
 
user manual  
QLight™ DP series  
MOUNTING AND FIXING  
Rigging Hardware  
A versatile range of mounting hardware is available that allows enclosures to be used in a variety  
of ways, in either mobile applications or permanent installations.  
A top hat stand type fitting is mounted in the base of  
QLight™ series cabinets for use with 35mm diameter  
loudspeaker stands with a load rating of at least 37kgs  
(82lbs).  
Pole mount sockets are also fitted to the top of QLight™  
series subwoofers. This allows these two enclosures to be  
used together as an extended frequency range system as  
shown with the TQ-445DP mounted above the TQ-425DP.  
An optional 35mm diameter straight pole used between  
these enclosures enables a minimum footprint and ensures  
the correct vertical distance between cabinets.  
Internal metric threaded rigging points are provided  
on the TQ-445DP cabinet enabling it to be flown using  
optional M10 shoulder eyebolts. Downward  
inclination of the enclosure can be adjusted using an  
additional rigging point on the rear of the cabinet.  
Note: these rigging points must NOT be used to rig a  
second enclosure in a vertical column.  
Side-mounted flying strips can be fitted to the sides  
of the TQ-445DP enclosure by removing the  
countersunk bolts on the top and sides of the cabinet  
and replacing them with the M10 bolts supplied with  
the hardware. Two flying strips are required for each  
enclosure; one attached to each side. This method  
offers a simple and cost effective method of flying  
single enclosures in permanent installations.  
Enclosures may be arranged in a vertical column by  
coupling the flying strips together using QL-75  
QLight DP series manual  
page 21  
 
user manual  
QLight™ DP series  
quicklinks or shackles. When used in this way the load is taken through the flying strips rather than  
through the woodwork of the enclosure.  
Side-mounted flying strips can be fitted to the sides of QLight™ subwoofers to enable them to be  
flown as part of a permanent installation. Two different lengths of flying strips are optionally  
available for flying enclosures in either a vertical or horizontal orientation. These are fitted by  
removing the countersunk bolts on the top and sides of the cabinet and replacing them with the  
M10 bolts provided with the hardware. Two flying strips are required for each enclosure. This  
method offers a simple and cost effective method of flying single or multiple TQ-425 enclosures,  
with the load being taken through the steel strips rather than through the woodwork of the  
enclosure. Enclosures may be arranged in a vertical column by coupling the flying strips together  
using QL-75 quicklinks or shackles. FF-425 flying strips are load tested.  
WARNING: Rigging eyebolts must not be used for flying this enclosure. You must use the optional  
Turbosound steel flying strips described above.  
The universal FB-12 flybar assembly enables the use of  
several different fixing methods for the TQ-445DP, all shown  
in the diagram here. The flybar is attached to the cabinet  
using a pair of captive M10 shoulder eyebolts (supplied with  
the flybar assembly). There are 12 attachment points equally  
spaced along the length of the spine of the flybar. Depending  
on which point is chosen for the given attachment system, a  
wide range of downward inclination angles can be achieved  
over a range of approximately 70 degrees. The design of the  
flybar even allows for upward angles, for example for  
coverage of balconies that are higher than the loudspeaker  
location.  
QLight DP series manual  
page 22  
 
user manual  
QLight™ DP series  
The FB-12 flybar assembly comes supplied with a U-6 Unilock fitting, which provides a single  
attachment point. The point at which the Unilock is attached to the flybar determines the vertical  
angle of the loudspeaker as shown in the table following.  
A pick-up point adapter offers a further single attachment point. This option provides fast  
adjustment of vertical angle. The point at which the eyebolt adapter is attached to the flybar  
determines the vertical angle of the loudspeaker as shown in the table following.  
The SC-440 aluminium scaffold clamp is attached to the T-bar by means of a simple clevis  
coupler. It is designed to rotate horizontally through 360° in order to enable accurate positioning  
of the loudspeaker. The point at which the scaffold clamp is attached to the flybar determines the  
vertical angle of the loudspeaker as shown in the table following.  
The following table gives the predicted downward angle of the enclosure.  
Attachment position  
Vertical angle (negative angle denotes upwards)  
Hole number 1 (front of cabinet)  
-29°  
-23°  
-17°  
-10°  
-3°  
Hole number 2  
Hole number 3  
Hole number 4  
Hole number 5  
Hole number 6  
4°  
Hole number 7  
11°  
18°  
24°  
30°  
35°  
40°  
Hole number 8  
Hole number 9  
Hole number 10  
Hole number 11  
Hole number 12 (rear of cabinet)  
QLight DP series manual  
page 23  
 
user manual  
QLight™ DP series  
Flying frames are avail able for use with the TQ-308DP, TQ-310DP and TQ-445DP. These enable  
the cabinets to be installed in semi-permanent applications with the maximum of security. They  
provide considerable variation of horizontal and vertical inclination, including upward angles, and  
is very easy to re-position and angle once rigged. Optional scaffold clamps and pole adapters are  
additionally available.  
Permanent Installations  
Any installation, whether temporary or permanent, must be securely attached to the structure of  
the building using chain, steel wires or web straps which are certified and load rated for the  
purpose. The combined weight of the sound system, its cables and the rigging system must be  
safely carried by the points at which attachment is made to the building or structure. Great care  
must be taken in selecting the attachment points and methods, being absolutely sure of the load  
carrying capacity of points chosen.  
NOTE: The rigging of loudspeaker systems is an extremely serious matter with potentially  
lethal consequences should anything go wrong. It is of vital importance that you, or other people  
rigging the system, are suitably qualified to do so and have a full understanding of all the factors  
involved with safety as a number one priority. Turbosound accepts no responsibility for any  
accident, damage or failure of any rigged system. This rigging information is specifically related to  
the requirements of QLight™ enclosures only. For more detailed information on the whole topic of  
rigging various handbooks are available. If you are in any doubt contact your Turbosound dealer  
who will be able to refer you to an experienced rigging company.  
Choosing the best location  
When using any QLight™ system, certain room parameters will affect the resultant sound quality  
and coverage. For example, any boundary like a wall or floor will lift certain frequencies. If you are  
placing the unit in a corner then a lift at the bass end is to be expected and it may sound rather  
boomy. This can be compensated for moving the speaker or cutting low frequencies with a  
graphic equaliser.  
When speakers are flown in free space then boundary effects are minimised. The result is a  
smooth frequency response without any boost at odd frequencies, but the bass end may appear  
subjectively light. In this case increase the sub-bass level to bring the low end up.  
The relationship between sound pressure level and distance is an “inverse square law” so  
remember that every time the distance from the sound source is doubled the sound level  
decreases by 6dB. For every 3dB increase in SPL you need a doubling of input power and you can  
work out the wattage input needed to give the required SPL levels at various distances from the  
loudspeaker(s).  
QLight DP series manual  
page 24  
 
user manual  
QLight™ DP series  
It was stated earlier that the TQ-445DP’s tightly controlled directivity gives it essentially point and  
shoot qualities. Every room has its own unique set of characteristics that affect any sound  
introduced into the room. These include reverberation reflections and decay time, sound  
absorption of materials used, temperature and humidity, etc. A degree of experimentation with  
different locations (if possible) is best, especially if you are permanently installing the speaker and  
have particular requirements where you want to concentrate the sound into a specific area.  
Any boundary like a wall or floor will lift certain frequencies. If you are fixing the unit to a wall, or  
in a corner then a lift at the bass end is to be expected and it may sound rather boomy. Either  
reduce the low end by means of a graphic equaliser or move the speaker.  
Rooms with a lot of soft furnishings, curtains and drapes will absorb sound, especially at high  
frequencies. These rooms can sound rather dead and may appear to need more amplifier power to  
generate high SPL’s but have the advantage that the sound needs less equalisation and is easier to  
control. In this case the listener receives mainly direct sound, that is the sound emanating directly  
from the loudspeaker, with little reflected sound.  
If the room has a lot of hard, exposed surfaces such as wooden floors, brick or plaster walls or  
glass windows, these will reflect the sound, causing it to bounce around the room and sounding  
over bright. These rooms also tend to have various resonances that will be excited by high SPL’s.  
Listening in the middle of the room you will hear a lot of reflected sound in comparison with the  
direct sound. Care is needed with speaker positioning, SPL’s and equalisation. If the room is large  
and very reverberant then bass roll-off below about 250 Hz may be required to ensure a  
reasonable level of intelligibility.  
For long, narrow rooms the traditional left and right stacks (floor, wall mounted or flown) can  
suffice with good stereo imaging in the centre of the room. For multi-tier venues such as theatres,  
speakers should be flown or wall mounted to project into each tier. In highly reverberant rooms  
often a central cluster is the best option. This acts as a virtual point source with all the sound  
emanating from one point in the room, but path lengths should be carefully calculated.  
QLight DP series manual  
page 25  
 
user manual  
QLight™ DP series  
MAINTENANCE  
If any of the drive units should cease functioning you are advised to remove the faulty unit from  
the cabinet and send it to a professional service centre authorised to recone Turbosound  
loudspeakers. This will ensure the continued high performance of your QLight™ series product.  
Removal of the low frequency driver – TQ-308DP, TQ-310DP, TQ-315DP  
Unscrew the six countersunk socket head screws at the side of the cabinet that hold the protective  
grille in place. Be careful when removing the grille as it is under tension and may spring outwards  
when released. Set the grille and fixing screws aside for later re-assembly.  
Undo the four Allen head bolts holding the driver in place, and carefully pull it out and away from  
the cabinet. WARNING - this unit is heavy! Disconnect the cables from the loudspeaker terminals  
and completely remove the driver from the cabinet. Make a note of the driver polarity for later  
reconnection.  
To reinstate the driver, simply reverse the procedure making sure you observe the correct polarity  
when reconnecting the cables back into the terminals of the drive units.  
Removal of the HF unit – TQ-308DP, TQ-310DP  
Remove the grille as described above. Set the grille and fixing screws aside for later re-assembly.  
Unscrew the four Allen head bolts holding the high frequency range horn in place and carefully  
pull it out and away from the cabinet. WARNING - this unit is heavy! Disconnect the cables from  
the loudspeaker terminals and completely remove the driver from the cabinet. Make a note of the  
driver polarity for later reconnection.  
To reinstate the driver, simply reverse the procedure making sure you observe the correct polarity  
when reconnecting the cables back into the terminals of the drive units.  
Removal of the 12”/1” driver – TQ-445DP  
Unscrew the eight countersunk screws from the two vertical battens which hold the protective  
grille in place. Be careful when removing the grille as it is under tension and may spring outwards  
when released. Set the battens, grille and fixing screws aside for later re-assembly.  
Undo the eight M6 x 30mm Allen head bolts holding the driver in place and carefully pull it out  
and away from the cabinet. WARNING - This unit is heavy! You will notice that the 1” high  
frequency driver is attached to the back of the 12” low frequency driver by its screw adapter.  
Disconnect the cables from both HF and LF units and completely remove the driver assembly from  
the cabinet. Make a note of the driver polarity for later reconnection.  
Separate the drive units by unscrewing the high frequency driver anti-clockwise and lift it away  
QLight DP series manual  
page 26  
 
user manual  
QLight™ DP series  
from the low frequency driver. Depending on which section needs servicing, the appropriate drive  
unit should be returned to an authorised Turbosound service centre.  
To reinstate the drivers, simply reverse the above procedure making sure you observe the correct  
polarity when reconnecting the cables back into the terminals of the drive units.  
Removal of the midrange unit – TQ-445DP  
If the midrange drive unit requires maintenance, it will first be necessary to remove the amplifier  
module. The midrange driver is held in place by a M10 x 25mm bolt through the rear of the  
cabinet into the back plate of the drive unit underneath the amplifier module. Once this is released  
the midrange horn and drive unit assembly can be removed.  
Remove the amplifier module as described below and set it aside.  
The M10 bolt securing the midrange driver will now be accessible in a recess in the enclosure rear  
panel. Using a 17mm socket, unscrew the bolt and set aside for later re-assembly.  
Unscrew the eight countersunk screws from the two vertical battens which hold the protective  
grille in place. Be careful when removing the grille as it is under tension and may spring outwards  
when released. Set the battens, grille and fixing screws aside for later re-assembly.  
The midrange horn is secured through the mounting flange with four #10 x 1/12” pan head wood  
screws. Unscrew these and lift out the horn and driver assembly.  
Disconnect the cables, making a note of the polarity, and carefully lift the driver clear.  
Removal of the low frequency driver – TQ-425DP  
Unscrew the countersunk screws from the four battens which hold the protective grille in place.  
Undo the four Allen head bolts holding the driver(s) in place, and carefully pull it out and away  
from the cabinet. WARNING - this unit is heavy! Disconnect the cables from the loudspeaker  
terminals and completely remove the driver from the cabinet. Make a note of the driver polarity  
for later reconnection.  
To reinstate the driver, simply reverse the procedure making sure you observe the correct polarity  
when reconnecting the cables back into the terminals of the drive units.  
Removal of the low frequency driver – TQ-115DP  
Unscrew the six countersunk socket head screws at the side of the cabinet that hold the protective  
grille in place. Set the grille and fixing screws aside for later re-assembly.  
Undo the four Allen head bolts holding the driver(s) in place, and carefully pull it out and away  
QLight DP series manual  
page 27  
 
user manual  
QLight™ DP series  
from the cabinet. WARNING - this unit is heavy! Disconnect the cables from the loudspeaker  
terminals and completely remove the driver from the cabinet. Make a note of the driver polarity  
for later reconnection.  
To reinstate the driver, simply reverse the procedure making sure you observe the correct polarity  
when reconnecting the cables back into the terminals of the drive units.  
Removal of the amplifier module – all models  
Release the M5 and M6 Allen head bolts securing the amplifier module to the rear of the cabinet  
and disconnect the spade connections from the module. The module can now be lifted clear of the  
cabinet and set aside.  
Replacement is a straightforward reversal of the above procedure. The wires should be connected  
as follows:  
Channel A + : Red  
Channel A - : Black  
Channel B + : Brown  
Channel B - : Blue  
QLight DP series manual  
page 28  
 
user manual  
QLight™ DP series  
APPENDIX A: SPARES AND ACCESSORIES  
CD-114 1” (25mm) HF compression driver TQ-445DP  
CD-110 1” (25mm) HF compression driver TQ-308DP, TQ-310DP  
CD-208 1.4” (35mm) HF compression driverTQ-315DP  
LS-1018 10” (254mm) LF loudspeaker  
LS-1214 12” (305mm) LF loudspeaker  
LS-1526 15” (381mm) LF loudspeaker  
LS-1520 15” (381mm) LF loudspeaker  
LS-6505 6.5” (165mm) MF loudspeaker  
LS-8010 8” (203mm) LF loudspeaker  
TQ-310DP  
TQ-445DP  
TQ-425DP, TQ-115DP  
TQ-315DP  
TQ-445DP  
TQ-308DP  
RC-1018 Recone kit for LS-1018  
RC-1214 Recone kit for LS-1214  
RC-1526 Recone kit for LS-1526  
RC-1520 Recone kit for LS-1520  
RC-6505 Recone kit for LS-6505  
TQ-310DP  
TQ-445DP  
TQ-425DP, TQ-115DP  
TQ-315DP  
TQ-445DP  
RD-114 Replacement diaphragm  
TQ-445DP  
RD-110 Replacement diaphragm for CD-110TQ-308DP, TQ-310DP  
RD-208 Replacement diaphragm for CD-208TQ-315DP  
Flying accessories  
BS-445 Biscuit  
EB-10  
FB-12  
M10 shoulder eyebolt  
Universal fly bar assembly  
FH-PH Pole holder for flying frame  
FF-445 Flying strips (2 required per enclosure)  
FF-425L Flying strips (2 required per enclosure) vertical  
FF-425S Flying strips (2 required per enclosure) horizontal  
FH-308 Flying frame  
FH-310 Flying frame  
FH-445 Flying frame  
PP-445 Pick-up point adapter  
SCLAMPScaffold clamp for flying frame  
TS-445 Tilting strap  
U-6  
Unilock  
QLight DP series manual  
page 29  
 
user manual  
QLight™ DP series  
APPENDIX B: TECHNICAL SPECIFICATIONS  
TQ-308DP  
TQ-310DP  
TQ-315DP  
Dimensions  
464mm x 270mm x 301mm  
(18.3” x 10.6” x 11.8”)  
525mm x 315mm x 300mm  
(20.7” x 12.4” x 11.8”)  
691mm x 443mm x 420mm  
(27.2” x 17.4” x 16.5”)  
Net weight  
15.5kg (34.1lbs)  
20.5kg (45.1lbs)  
32kgs (70.4lbs)  
Components  
1 x 8” (203mm) LF driver  
1 x 1” (25mm) HF  
1 x 10” (254mm) LF driver  
1 x 15” LF driver  
1 x 1” (25mm) HF compression 1 x 1.4” HF driver  
driver  
compression driver  
Frequency  
response  
68Hz – 20kHz ±4dB  
65Hz – 20kHz ±4dB  
50Hz – 20kHz ±4dB  
Nominal  
100°H x 60°V @-6dB points  
100°H x 60°V @-6dB points  
80°H x 50°V @-6dB points  
dispersion  
Max SPL  
Construction  
Grille  
120dB cont., 126dB peak  
124dB cont., 130dB peak  
130dB cont., 136dB peak  
12mm (1/2”) birch plywood  
12mm (1/2”) birch plywood  
18mm (3/4”) birch plywood  
Reticulated foam on  
expanded steel mesh  
Reticulated foam on expanded Reticulated foam on expanded  
steel mesh  
steel mesh  
Connectors  
(1) XLR female, (1) XLR male (1) XLR female, (1) XLR male  
(1) XLR female, (1) XLR male  
wired pin 2 hot  
wired pin 2 hot  
wired pin 2 hot  
Mains  
Neutrik PowerCon®  
Neutrik PowerCon®  
Neutrik PowerCon®  
Options  
TurboBluesemi-matt  
TurboBluesemi-matt textured TurboBluesemi-matt textured  
paint paint  
textured paint  
Due to continuing product improvement the above specifications are subject to change.  
QLight DP series manual  
page 30  
 
user manual  
QLight™ DP series  
TQ-445DP  
TQ-425DP  
TQ-115DP  
Dimensions  
588mm x 409mm x 363mm  
(23.1” x 16.1” x 14.3”)  
836mm x 511mm x 632mm  
(32.9” x 20.1” x 24.9”)  
559mm x 450mm x 600mm  
(22” x 17.7” x 23.6”)  
Net weight  
34.5kgs (75.9lbs)  
57kg (125.4lbs)  
32.2kg (70.8lbs)  
Components  
1 x 12/1” LF/HF driver  
1 x 6.5” MF driver  
2 x 15” (381mm) LF drivers  
1 x 15” (381mm) LF driver  
Frequency  
response  
55Hz – 20kHz ±4dB  
45Hz – 200Hz ±4dB  
47Hz – 180Hz ±4dB  
Dispersion  
Max SPL  
Construction  
Grille  
60°H x 40°V @-6dB points  
131dB cont., 137dB peak  
15mm (1/2”) birch plywood  
N/A  
N/A  
132dB cont., 138dB peak  
18mm (3/4”) birch plywood  
126dB cont., 132dB peak  
18mm (3/4”) birch plywood  
Reticulated foam on expanded Reticulated foam on expanded Reticulated foam on expanded  
steel mesh  
steel mesh  
steel mesh  
Connectors  
(1) XLR female, (1) XLR male  
wired pin 2 hot  
(1) XLR female, (1) XLR male  
wired pin 2 hot  
(1) XLR female, (1) XLR male  
wired pin 2 hot  
Mains  
Neutrik PowerCon®  
Neutrik PowerCon®  
Neutrik PowerCon®  
Options  
TurboBluesemi-matt textured TurboBluesemi-matt textured TurboBluesemi-matt textured  
paint paint paint  
Due to continuing product improvement the above specifications are subject to change.  
QLight DP series manual  
page 31  
 
user manual  
QLight™ DP series  
APPENDIX C: WARRANTY  
Limited Warranty  
This Turbosound loudspeaker product is warranted to the original end-user purchaser and all  
subsequent owners for a period of one (1) year for electronics assemblies and two (2) years for  
loudspeakers from the original date of purchase.  
Warranty Coverage  
Warranty coverage includes defects in materials and workmanship. It does not include:  
damage caused by accident, misuse, abuse, neglect or modification by any person other  
than an authorised Turbosound representative,  
damage caused by failure to operate the product in accordance with the instructions  
contained in the user manual,  
damage occurring during shipment in transit,  
claims based on any misrepresentation by the seller,  
products which do not have the original components as specified in the product  
engineering information,  
products on which the serial number has been removed or defaced.  
Shipping  
Should any fault develop with a component of your Turbosound system, please return the product,  
freight pre-paid, in its original packing carton, along with proof of purchase such as the original bill  
of sale or receipted invoice, and a description of the suspected fault to Turbosound Ltd. (Att:  
Customer Service), Star Road, Partridge Green, West Sussex RH13 8RY, England, or your local  
authorised Turbosound representative. The product serial number must be quoted in all  
correspondence relating to the claim. Insurance is recommended, as Turbosound or its  
representatives are not liable for loss or damage in transit. Turbosound will pay for return freight  
costs should repairs be covered under warranty.  
QLight DP series manual  
page 32  
 
user manual  
QLight™ DP series  
Incidental and consequential damages  
Turbosound's liability is limited to the repair or replacement, at our option, of any defective  
product, and shall not be liable for any incidental and consequential damages including, without  
limitation, injury to persons or property or loss of use.  
Limitation of implied warranties  
All implied warranties, including warranties of merchantability and fitness for a particular purpose,  
are limited in duration to the length of this warranty.  
This warranty is in addition to, and in no way detracts from, your statutory rights as a consumer.  
No other warranty is expressed or implied.  
Please record your purchase information below for future reference:  
Dealer Name ..................................................................................................................................  
Dealer Address ...............................................................................................................................  
.........................................................................................................................................................  
.........................................................................................................................................................  
Post / Zip Code ...............................................................................................................................  
Dealer telephone / fax ...................................................................................................................  
Invoice number ..............................................................................................................................  
Date of purchase ............................................................................................................................  
Unit serial number .........................................................................................................................  
QLight DP series manual  
page 33  
 
 
Turbosound Ltd.  
Star Road, Partridge Green  
West Sussex RH13 8RY United Kingdom  
Tel: +44 (0)1403 711447 Fax: +44 (0)1403 710155  
 

Techno Source Handheld Game System 30451 User Manual
Tokina Camera Accessories TVR0616 User Manual
TP Link Wireless Office Headset TL WA730RE User Manual
Tunturi Elliptical Trainer CE35 User Manual
Ultratec Projection Television 50DX20B User Manual
Unitech Barcode Reader MR350MKII User Manual
Viking Microwave Oven DMOR205 User Manual
Vulcan Hart Oven VCG10H User Manual
Wachsmuth Krogmann Carpet Cleaner VC9385S User Manual
Weed Eater Blower 545186753 User Manual