D I S H WA S H E R
B D W 1 0
822 90 11-50
I N S T R U C T I O N B O O K L E T
Important safety information
Before installing and first using the dishwasher, read the instruction booklet carefully, including
its hints and warnings. Doing so will ensure that your machine will perform properly and to best
advantage. Anyone using the machine should be thoroughly familiar with its instructions for use
and safety features. Save these instructions and make sure they remain with the machine if it is
moved or sold, so that everyone using it through its life can be properly informed on appliance
use and safety.
■ Only use detergent specifically designed for use in
Installation and servicing
■ All installation and service work done on the product
dishwashers.
■ If you take any dishes out of the machine before the
end of the dishwashing cycle, it is extremely important
to rinse them thoroughly under running water to remove
any remaining detergent.
must be carried out by a qualified technician. Work
performed by persons with inadequate knowledge may
adversely affect the satisfactory functioning of the
product and may cause personal injury or damage.
Before any work is carried out on the dishwasher, it
must be isolated from the electrical supply. To do this
the power plug must be removed from the wall socket.
■ Do not place sharp knives with their points upwards.
It is much safer to lay them horizontally in the basket.
■ When finishing loading or unloading close the door,
■ Water connection shall be made via an easily accessible
as an open door can be a hazard.
stopcock.
■ Make sure that the machine is disconnected from the
■ The power cable must be plugged into an earthed
socket, which must be easily accessible. Permanent
installation must only be carried out by an authorized
electrician.
power supply during cleaning and maintenance work.
■ After using the machine, turn off its water supply and
disconnect it from the power supply. When removing
the electrical plug, grip the plug, not the cable.
■ If the power cable is damaged, it must be replaced by a
special cable or assembly available from Service Force.
Identification of materials
■ Make sure that the power cable is not nipped or other-
wise damaged and that the hoses do not get crushed
or kinked when moving the dishwasher in connection
with installation or cleaning etc.
All materials used in packaging this machine are
environmentally-friendly. The various plastics used
are identified and can be recycled:
• PE stands for polyethylene, which is used for the
bag around the machine and the bag in which
these instructions were supplied.
■ Servicing and repairs must be carried out by a trained
service technician. Only use genuine spare parts
available from your local Service Force Centre. Never
try to repair the dishwasher yourself.
• PS stands for polystyrene (moulded), which is
used for the sections of packaging needed to
cushion the machine.
Child Safety
■ The dishwasher should be used by adults only. Do not
The cardboard components of the packaging are made
from recyclable paper and should be taken to a collection
point for recycling.
let children play with the controls or other parts of it.
The machine contains plastic and rubber components.
These have identifying marks to show what they are
made from, so they can be recycled or disposed of
properly at the end of the machine's life.
The materials are identified according to international
standards.
■ Keep all packaging well away from children.
■ Keep all detergents in safe place out of children´s
reach.
■ Prevent children from sitting, swinging or standing
on the open door.
During Use
■ This dishwasher is designed solely for washing house-
hold utensils suitable for machine washing. Using it for
other purposes could lead to physical injury or damage
to property and invalidate the guarantee.
■ Avoid opening the door while the dishwasher is running,
as hot steam may escape.
- 3 -
Care and cleaning
2
1
6
3
4
5
Important
Spray arm (2)
Make sure that the machine is unplugged and the water
turned off before undertaking any kind of maintenance.
The holes in the spray arm nozzle must be kept clean to
ensure satisfactory wash results. Inspect the spray arm
regularly. When thorough cleaning is necessary, remove
the spray arm by unscrewing the nut clockwise (it has a
left-handed thread) and lift off the spray arm.
General cleaning
Inspect the filters and spray arm nozzle before re-loading
the machine and remove any food scraps. Wipe round
the rubber gasket at the bottom of the door to remove
grease which tends to collect there.
Wash the spray arm with hot soapy water using a stiff
saucepan brush if necessary to remove scraps.
Re-assemble carefully, making sure the nut is secure.
Rinse aid dispenser (1)
Coarse filter (3)
Use of rinse aid will result in faster drying of the load and
gives the dishes a shiny finish. It may be necessary to
adjust the quantity of rinse aid dispensed if you live in either
a very hard water or a very soft water area. More is needed
for hard water and less for soft water. Leave the dispenser
in its preset position when you first use the dishwasher and
only adjust if, after a few cycles, you notice the following:
The purpose of the coarse filter is to catch large objects
such as toothpicks and pieces of eggshell. Make sure
that the filter is always clean. Lift it out and rinse it under
running water whenever necessary.
Fine filter (4)
It is just as important to keep this filter clean. A dirty or
clogged filter will impair washing efficiency. The fine filter
can easily be lifted out for cleaning when you have
removed the coarse filter.
• Crockery remaining dull looking and/or showing
occasional round spots. If this happens, increase the
quantity of rinse aid by turning the red dial below the
filler trough clockwise.
The dishwasher must not be used without the
filters. Incorrect repositioning of the filters will
produce poor washing results.
• Crockery feeling sticky or showing whitish spots. If this
happens, decrease the quantity of rinse aid by turning
the red dial below the filler trough anti-clockwise.
Cleaning of the filters is vital to ensure correct
operation of the machine.
The dispenser holds about 140 ml. This is enough for 40-
70 wash cycles, depending on the dosage setting. When
the rinse aid level is approaching the bottom of the scale it is
time to refill the dispenser. Swivel out the filler trough and
carefully fill up with rinse aid until the level reaches up to
the red mark on the level indicator tube. Do not overfill, and
carefully wipe off any spillage with a damp cloth immediately.
Don’t forget to close the filler trough afterwards.
Do not fill the rinse aid dispenser with liquid
detergent.
- 4 -
Detergent dispenser (5)
Cleaning the cabinet
Wipe the outside of the cabinet and control panel regularly
with a soft damp cloth. If necessary, use warm soapy water,
rinse with a damp cloth and rub dry with a soft duster.
Only use detergents specially designed for dishwashers.
Pour the detergent into the compartment, for a normal
load pour about 15g. Since not all detergents are the
same, you should also consult the instructions on the
packet. Remember that the instructions usually refer to
full-size dishwashers, for example when using detergent
tablets, it is sufficient to use just half a tablet. Using the
correct amount of detergent also contributes to reducing
pollution.
Never use abrasive cleaners which could damage the
surface, ie: scouring pads or solvents (acetone, trichlori-
ethylene, etc).
If the machine is not going to be used for some time, take
the folllowing precautions:
1. Unplug the machine and turn off the water supply.
2. Fill up the rinse aid container.
Bendix recommends the use of Finish dish-
washer detergent and Rinse Aid.
3. Make sure the tub is clean by carrying out a wash
programme (without any crockery) using Finish
Dishwasher cleaner, then dry the inside thoroughly.
Water softener (6)
This dishwasher is equipped with a water softener for hard
(chalky) water, therefore the rinse aid dispenser should
be set for a low dosage.
4. Leave the door ajar.
The lime (chalk) in hard water causes white deposits to
occur on dishes and the interior of the dishwasher.
To prevent this, the water has to pass through a special
container where its hardness is removed. Since the water
softener consumes coarse dishwasher salt, you will have
to replenish the salt container after a certain number of
dishwashing cycles. When the indicator lamp on the
control panel lights up, it is time to fill up with salt.
Proceed as follows:
1. Unscrew the salt container filler cap.
2. Fill up salt container with water (only the first
time).
3. Fill the container with coarse salt. Use the funnel
supplied with the machine.
Ordinary domestic salt will affect the efficiency
of the water softener and damage it.
4. Remove the funnel and wipe off any spillage.
5. Screw the filler cap back in place.
The salt container holds about 1 litre, which is enough for
about 20 - 30 dishwashing cycles. Always ensure that
there is water in the salt container before filling with salt.
Water softener plug (7)
As supplied from the factory, the water softener is set for
a water hardness of up to 20°dH. If your water is harder
than this, you can increase the capacity of the water
softener by pulling out the rubber plug at the rear of the
dishwasher on the left hand side viewed from the back.
See illustration.
7
Contact your local Water Authority to find the exact water
hardness level for your area.
Never run the dishwasher without salt in the container as
this may damage the water softener. If the damage is slight,
the water softener function can be partially restored by
filling the container with salt and then running the Normal
cycle 4-5 times.
- 5 -
The control panel
1
4
3
2
1 Temperature selector
55° - Button in
65° - Button out
Wash phase
Rinse phase
2 Programme knob
To start the machine:
Turn the selector knob clockwise to the programme
start. The On/Off switch is built into the programme
timer. During the water heating process, the timer
is standing still. To isolate the dishwasher from the
mains completely, unplug it from the wall socket.
3 Indicator lamp
Door lock
Press the handle down and open the door. Avoid opening
the door while the machine is running, steam and hot water
could escape from the machine which may cause an injury.
While the programme is in progress, the indicator
lamp is lit and it goes out when the programme has
finished.
If the door is opened slightly after a completed
programme the dishes will dry faster.
4 Salt indicator lamp
The operating lamp indicates when the salt needs to be
replenished. The lamp may remain lit for one or more
programmes after refilling the salt container, this is
normal.
- 6 -
How to load the dishwasher
The illustration shows the machine loaded with five stan-
dard place settings. Your own dishes are not likely to be
identical to this load, but if you follow the advice below
we are sure you will be pleased with the results.
1
• Always place glasses, cups and bowls upside down.
• Incline deep dishes (soup plates etc.) so that the
water can run off when drying.
• Make sure that the dishes do not rest against each
other. This is particularly important in regard to the
cutlery basket - nested spoons, etc. simply cannot be
properly washed. The water must get at all the soiled
surfaces.
• Make sure that cutlery with slender handles and other
items do not protrude through the openings in the
basket and prevent the spray arm from rotating.
• Never put silver and stainless steel objects together.
When these metals come into contact with each other
a chemical reaction occurs which stains the silver.
• China with a pattern applied on top of the glaze may
not be suitable for machine washing as the colours
may fade and lose their lustre. The same applies to
cutlery with wooden or plastic handles.
Make sure you always buy articles that are
dishwasher proof.
• Not all plastic articles are machine washable. If you
are in doubt as to whether your plasticware can be
machine washed, we suggest you check by washing
a single item or else wash them by hand.
2
• Aluminium becomes dull and tarnished when machine
washed. The machine gets it clean, but at the expense
of its appearance.
• When washing delicate items, select the lower wash
temperature.
• Substances such as ketchup containing strong
colouring agents can cause temporary discolouration
in the machine.
Instruction for test centres
Test standard:
EN 50242
Rated capacity:
5 place settings
Loading of rack:
Test program:
According to figure 1
Normal 65° C
Detergent (IEC type B):
Rinse aid (typ III):
Feed water pressure:
Waste water outlet:
15 gram in the dispenser
Setting medium
Minimum 0,8 bar, maximum 10 bar
Install according to figure 2
The salt container and rinse aid dispenser shall be filled in accordance with the instruction manual. Before conducting
the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load.
- 7 -
Using your appliance
3
1
2
6
5
4
Proceed as follows:
1. Scrape off solid food remnants.
2. Load the dishwasher. (See “How to load the dishwasher”).
Pour approx. 15 g detergent into the detergent dispenser.
3. Close the door.
4. Select the required temperature.
5. Start the dishwasher by turning the programme knob to
the start position.
6. Check the filters to see whether they need cleaning when
the dishwasher has finished the wash.
Detergent recommendations
For best results we recommend the use of Finish detergents, rinse aid and salt.
A complimentary sample pack is included in your new dishwasher.
- 8 -
Something Not Working?
Before calling out an engineer, please check through the details below because some faults can be rectified easily
without the need to call out an engineer. If an engineer is called to resolve a problem listed below or to repair a
fault caused by incorrect installation or mis-use a charge will be made, even if the appliance is under guarantee.
Fault
Check
■ Is the door closed properly?
The machine will not start.
■ Is there power to the machine?
■ Has the fuse blown? (Start with fuse in electrical plug).
■ Have you set the programme knob properly?
■ Is the water tap turned on?
The machine is not filling with water.
■ Is the water tap turned on?
■ Has your domestic water supply been cut off temporarily?
■ Is the water intake hose kinked or blocked?
■ Is the filter inside the intake hose blocked?
■ Is the water pressure too low?
■ Did you open the door before the light went out and the
cycle ended?
The machine will not drain.
■ Is the drain hose kinked?
■ Is the sink drain blocked?
Dishes not washed satisfactorily.
■ Are the baskets too full?
■ Have the dishes not been arranged properly?
■ Has anything prevented the spray arm from rotating?
■ Are the spray arm holes clogged?
■ Are the filters clogged?
■ Are the filters in position?
■ Did you use enough detergent?
■ Is the detergent old or has gone hard?
■ Is the salt container cap properly closed?
■ Is the washing programme selected too gentle?
■ Is the rinse aid dispenser empty?
■ Is the salt container empty or is the water softener not
correctly adjusted?
■ Is the rinse aid dispenser adjusted to too low dosage?
Visible lime deposits or white film on
the dishes.
The machine is noisy.
■ Are the dishes rattling against each other?
■ Is the spray arm knocking against the dishes?
The dishes are not quite dry.
The door is difficult to close.
■ Is the rinse aid dispenser empty?
■ Have the dishes been left too long inside the machine?
■ Is the dishwasher level?
Never attempt to repair the dishwasher yourself.
Repairs carried out by unauthorised or inexperienced
persons can cause injury or serious malfunctioning.
- 9 -
Service
Service and Spare Parts
In the event of your appliance requiring service, or if you wish
to purchase spare parts, please contact your local Service
Force Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the Service
Force Centre covering your post code area.
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
Before calling out an engineer, please ensure you have read
the details under the heading ”Something Not Working”.
When you contact the Service Force Centre you will need to
give the following details:
1.
2.
3.
4.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance
(found on the rating plate)
5.
The purchase date
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
Customer Care Department
For general enquiries concerning your Bendix appliance or
for further information on Bendix products, please contact
our Customer Care Department by letter or telephone at the
Customer Care Department
Bendix
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel:
08705 950950 *
* call to this number may be recorded for training purposes.
- 10 -
Guarantee Conditions
Standard guarantee conditions
We, Bendix, undertake that if within 12 months of the date of the purchase this BENDIX appliance or any part thereof
is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the
same FREE OF CHARGE for labour, materials or carriage on condition that:
•
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate
The appliance has been used for normal domestic purposes only and in accordance with the manufacturer’s
instructions
•
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us
•
•
•
All service work under this guarantee must be undertaken by a Bendix Service Force Centre
Any appliance or defective part replaced shall become the Company’s property
This guarantee is in addition to your statutory and other legal rights
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in
which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom
Appliances found to be in use within a commercial environment, plus those which are the subject to rental
agreements
Products of Bendix manufacture which are not marketed by Bendix
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject
to the following qualifications:
•
•
The guarantee starts from the date you first purchased your product
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products
•
•
•
This guarantee relates to you and cannot be transferred to another user
Your new home is within the European Community (EC) or European Free Trade Area
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household
•
The product is installed taking into account regulations in your new country
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and
your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 99
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219897
Nurnberg
Pordenone
Stockholm
Slough
Sweden
UK
- 11 -
Installation instructions
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical specifications
Dimensions
Height
Width
Depth
460 mm
450 mm
480 mm
Weight
Net
Gross
17 kg
20 kg
Capacity
5 settings
Water pressures
Minimum
Maximum
50 kPa (0.5 bar)
1000 kPa (10 bar)
Water Temperature
Electrical data
Cold fill only
Power supply
Fuse
230 V - 50 Hz
13 A
Heating element
Power rating
1200 W
1280 W
This appliance complies with the following E.E.C. directives:
73/23/EEC, dated 19.02.1973 – low-voltage directive.
89/336/EEC, dated 03.05.1989 (incl. amendment
–
–
–
92/31/EEC) – directive on electromagnetic compatibility.
- 12 -
Unpacking the machine
If the machine is damaged
If the dishwasher has been damaged during transport,
you should immediately notify the company responsible
for delivering it.
Check that the dishwasher is undamaged. If you
discover any damage, faults or that anything is missing,
you should notify the dealer immediately.
Never leave packaging material in a place where
children may play with it.
Check that the following accessories are supplied with
the dishwasher when you unpack it:
1
• A funnel for filling with salt (1)
• Elbow for discharge hose (2)
2
Use
This dishwasher is designed solely for washing household
utensils suitable for washing in a dishwasher. Using it for
other purposes may damage it and invalidate the guarantee.
Protecting the machine against
freezing
If the dishwasher is placed in an environment where the
temperature sometimes falls below 0° C, there is a risk
that the small amount of water which remains inside the
parts of the dishwasher will freeze and damage it.
To prevent this you should:
1. Turn off the water supply to the machine and
disconnect the water intake hose from the
supply pipe.
2. Make sure that there is dishwasher salt in the
salt container for the water softener.
The appliance is only to be used and stored
indoors at normal room temperature. The manu-
facturer accpets no responsibility for any frost
damage.
- 13 -
Installation
The dishwasher is intended for installation on a
kitchen sink or worktop. It is important to ensure
the dishwasher is level to avoid any difficulty
opening and closing the door. Its height can be
adjusted with the adjustable feet (8 mm each) in
each corner of the dishwasher.
Water inlet
The dishwasher should be permanently plumbed
into a separate cold water supply.
The water pressure must be within the limits given
in the technical specifications, as it will not function
correctly if pressure is outside these specifications.
Your local Water Authority will advise you on the
average mains pressure in your area. Where the
water is supplied from a cold water cistern you can
work out the pressure yourself by measuring the
vertical distance (or ‘Head’) between the machine’s
inlet hose and the outlet from the cold water storage
cistern; allowing .86 psi for every 2 feet under normal
conditions.
We would advise you to have a shut-off valve or
stopcock in the water supply pipe close to the dish-
washer and accessible for easy use. This should
be turned off when the appliance is not in use.
Connect the inlet hose to a tap with a 3/4” pipe
thread.
The inlet hose must not be joined onto any form of
extension hose. If it is too short, the entire hose
must be replaced with a longer high-pressure hose,
specially designed for the purpose. The end of the
hose, which is connected to the dishwasher can be
turned in any direction. Loosen the retaining nut,
turn the hose, then retighten the nut.
Check that the nut is tight before the
machine is moved into position.
Use only the inlet hose supplied to the
dishwasher, do not reuse the old inlet
hose.
Water drainage
Place the discharge hose over the sink as illustrated.
It must not at any point be higher up than 75 cm over
the surface which the dishwasher is standing on.
If it runs higher, operation of the dishwasher might
be impaired.
It is also important to ensure that the inside diameter
of the hose is not less than 13 mm at any point.
If the discharge hose is too long it can easily be cut
to the right length.
1. Cut the hose to a suitable length, using a
sharp knife.
2. Fit the elbow supplied onto the end of the
hose.
- 14 -
Power supply
The dishwasher is supplied with a lead and electrical plug
for connection to a 230 V, 13 A earthed wall socket.
Before any work is carried out on the dishwasher, it must be
isolated from the electric mains supply, for example by
removing the plug from the wall socket.
Permanent electrical installation must be
carried out by an authorised electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The manufacturer declines any liability should this
safety measure not be observed.
If the plug that is fitted to your appliance is not suitable
for your socket outlet, it must be cut off and the appropriate
plug fitted.
GREEN & YELLOW
13 AMP FUSE
Remove the fuse from the cut off plug.
The cut off plug should then be disposed of to prevent the
hazard of shocks in case it should be plugged into a 13
amp socket in another part of your home.
Important
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
BROWN
CORD CLAMP
BLUE
Brown
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with
the markings identifying the terminals in your plug,
proceed as follows:
Connect the Green and Yellow (earth) wire to the terminal
in the plug which is marked with the letter «E» or the
earth symbol
or coloured green and yellow.
Connect the blue (neutral) wire to the terminal in the plug
which is marked with the letter «N» or coloured black.
Connect the brown (live) wire to the terminal in the plug
which is marked with the letter «L» or coloured red.
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13 amp BSI362 fuse.
Only ASTA or BSI approved fuses should be used.
- 15 -
© Electrolux plc 2003
|