Quality Refrigeration
OWNER’S MANUAL
Instructions for the installation, operation
and maintenance of all Traulsen Spacesaver Models:
Refrigerator Models: UR30HT, UR48HT, UC27HT
Freezer Model: UR30LT
Refrigerator/Freezer Model: UR48DT
Wine Cabinets: UR30WT, UR48WT, UC27WT
This Traulsen unit is built to our highest quality standards. We build our refrigerators, freezers and heated
cabinets this way as a matter of pride. This philosophy has made Traulsen the leader in commercial refrig-
eration since 1938. We thank you for your choice and confidence in Traulsen equipment and we know you
will receive many years of utility from this equipment.
All Traulsen units are placed on a permanent record file with the service department. In the event of any
future questions you may have, please refer to the model and serial number found on the name tag affixed
to the unit. Should you need service, however, call us on our toll free number, 800-825-8220 between 7:30
am and 4:30 pm CST, Monday thru Friday. It is our pleasure to help and assist you in every possible way.
INSTALLER
COMPLETE THE FOLLOWING INFORMATION PRIOR TO UNIT INSTALLATION
INITIAL START DATE:
MODEL TYPE:
SERIAL NO.
COMPANY/INDIVIDUAL NAME:
INSTALLER:
FORM NUMBER TR35749 REV. 5/03
P/N 375-60177-00
II. RECEIPT INSPECTION
III. INSTALLATION (continued)
All Traulsen products are factory tested for perfor-
mance and are free from defects when shipped. The
utmost care has been taken in crating this product to
protect against damage in transit. All interior fittings
have been carefully secured and the legs or casters
and bottom mounted condensate evaporator are boxed
and strapped inside to prevent damage. If the unit is
equipped with optional locks the door keys will be at-
tached to the handle with a nylon strip. The handle is
protected by an easily removable nylon netting.
III. c - INSTALLING LEGS OR CASTERS:
6” high stainless steel legs are supplied standard for
all Traulsen Spacesaver units. Casters in lieu of legs
are available as an optional accessory for the same
models. These are shipped from the factory packed
inside a cardboard box which is strapped to one of
the shelves. Remove the nylon strap and open the
box, it should contain either four (4) legs or four (4)
casters and sixteen (16) bolts.
WARNING: THE CABINET MUST BE BLOCKED AND
STABLE BEFORE INSTALLING LEGS OR CASTERS.
You should carefully inspect your Traulsen unit for
damage during delivery. If damage is detected, you
should save all the crating materials and make note
on the carrier’s Bill Of Lading describing this. Afreight
claim should be filed immediately. If damage is sub-
sequently noted during or immediately after installa-
tion, contact the respective carrier and file a freight
claim. Under no condition may a damaged unit be re-
turned to Traulsen & Co. without first obtaining writ-
ten permission (return authorization).
To install the legs or casters, first raise and block the
unit a minimum of 7” from the floor. For installing
legs, thread the legs into the threaded holes on the
bottom of the cabinet (see figure 1). Be certain that all
legs are tightly secured (legs and casters should be
tightened to 300 inch/pounds, max). When the unit is
set in its final position, it is important for proper op-
eration that the unit be level. The legs are adjustable
for this purpose, turn the bottom of the leg counter-
clockwise to raise it, clockwise to lower it. Level the
unit from front to back as well as side to side in this
manner, using a level placed in the bottom of the cabi-
net.
III. INSTALLATION
III. a - LOCATION:
Select a proper location for your Traulsen Spacesaver
unit, away from extreme heat or cold. Allow enough
clearance between the unit and the side wall so that
the door (s) may open a minimum of 90°.
III. b - PACKAGING:
All Traulsen Spacesaver units are shipped from the
factory bolted to a sturdy wooden pallet and packaged
in a durable cardboard container. The carton is at-
tached to the wooden skid with the use of large staples.
These should first be removed to avoid scratching the
unit when lifting off the crate.
Fig. 1
Please note that Traulsen Spacesaver units are not de-
signed to be moved while on legs. If the unit requires
moving, a pallet jack or forklift should be used to pre-
vent damage. For installing casters, the casters are
“plate” type, and require the use of four (4) bolts each
to secure them firmly to the cabinet bottom at each
corner (see figure 2). The caster bolts are tightened
using a 1/2” socket wrench.
To remove the wooden pallet, first if at all possible, we
suggest that the cabinet remain bolted to the pallet
during all transportation to the point of final installa-
tion. The bolts can then be removed with a 3/4” socket
wrench. Avoid laying the unit on its front, side or
back for removal of the pallet.
All exterior metal surfaces are protected from scratch-
ing during manufacturing and shipping by a plastic
covering. This should be removed prior to installa-
tion.
Figure 2
NOTE: Traulsen does not recommend laying the unit
down on its front, side or back. However, if you must
please be certain to allow the unit to remain in an up-
right position afterwards for 24 hours before plugging
it in so that the compressor oils and refrigerant may
settle.
-2-
III. INSTALLATION (continued)
III. f - REMOTE INSTALLATION:
III. d - SHELF PINS:
Remote models are supplied without compressors,
solenoid valves, etc. The correct voltage, amp listing,
refrigerant and BTU’s are listed on the unit’s serial tag.
It is the responsibility of the installer to specify and
supply the correct size compressor(s) based upon this
information and on-site requirements. Refrigerant line
installation must be done in adhering to good prac-
tice and local regulations. See section “III. e” for in-
formation concerning condensate removal for remote
models.
The unit is supplied with shelves and shelf pins in-
stalled. Check all shelf pins to assure they are tight-
ened down as they may have come loose during ship-
ping. Rotate the pins clockwise until they are secured
against the side of the cabinet.
III. e - INSTALLING THE CONDENSATE EVAPORATOR:
A bottom-mounted electric condensate evaporator is
normally supplied on all self-contained models. This
is shipped in a cardboard carton secured to the cabi-
net interior, and must be installed prior to use.
III. g - CORD & PLUG:
Most self-contained models are supplied with a cord
& plug attached. It is shipped coiled at the top of the
cabinet, secured by a nylon strip. For your safety and
protection, all units supplied with a cord and plug in-
clude a special three-prong grounding plug on the ser-
vice cord. Select only a dedicated electrical outlet with
grounding plug for power source. NOTE: Do not un-
der any circumstances, cut or remove the round
grounding prong from the plug, or use an extension
cord.
To install a bottom-mounted electric condensate
evaporator (see figure 3).
After the cabinet has been uncrated and the legs/cast-
ers attached, locate the four (4) holes on the exterior
bottom towards the rear of the cabinet. Then, using
the four (4) screws provided, attach the mounting rails
to the cabinet bottom (the end flange is to be up and
be facing towards the cabinet rear). Next, place the
heater into the heater bracket (note the enclosed
springs are only to be used when the heater is placed
on the floor). Slide heater and bracket into the mount-
ing rails. Plug the supplied cord into both the heater
on one end, and the electrical outlet, provided on the
cabinet exterior bottom towards the front, on the other.
Screw the “U-Trap” (UR30LT only) or 90 degree elbow
joint (all other Spacesaver models) into the drain line
located on the rear of the cabinet and then screw the
drain extension into the U-Trap or elbow joint.
III. h - POWER SUPPLY:
It is recommended that the supply voltage be checked
prior to connection to be certain that proper voltage
for the cabinet wiring is available (refer to the serial
tag to determine correct unit voltage). Make connec-
tions in accordance with local electrical codes. Use
qualified electricians.
Use of a separate, dedicated circuit is recommended.
Size wiring to handle indicated load and provide nec-
essary overcurrent protector in circuit.
Drain
Line
III. i - WIRING DIAGRAM:
U-Trap
Refer to the wiring diagram for any service work per-
formed on the unit. Should you require one, please
contact Traulsen Service at (800) 825-8220, and pro-
vide the model and serial number of the unit involved.
Electric
Heater
Drain
Extension
10-32 x 3/8 Screw (4)
Mounting Rails
BMCE
III. j - CLEARANCE:
Receptacle
In order to assure optimum performance, the condens-
ing unit of your Traulsen unit MUST have an adequate
supply of air for cooling purposes. Therefore, the
operating location must either have a minimum of 12”
clearance overhead of the condensing unit or allow
for unrestricted air flow at the back of the unit. Clear-
ance of at least 12” above is required in order to per-
form certain maintenance tasks.
Heater
Bracket
Figure 3
A remote model is normally configured for conden-
sate to be run to a floor drain unless purchased with a
condensate evaporator. The installer is responsible
for making the required extension to the floor drain in
accordance with good practice and local regulations.
The bottom mounted electric condensate evaporator
of your Traulsen Spacesaver should be cleaned occa-
sionally to keep it clear of dirt and debris.
-3-
III. INSTALLATION (continued)
III. k - BUILT-IN INSTALLATION:
Select a proper location for your unit away from ex-
treme heat or cold. Due to the unique air flow of the
unit, the Spacesaver can be built-in or used as a free-
standing unit. Allow enough clearance between the
unit and side wall so that the doors can be opened a
minimum of 90 degrees. The floor should be level,
firm and capable of supporting the weight of the fully
loaded unit.
Traulsen
Follow the typical installation instructions outlined in
Section “III. a” thru “III. j” as required.
All built-in units require a minimum of 1/2” clearance
around the cabinet for servicing (see figure 5). If top
clearance exceeds 1” the unit must be blocked per
the free-standing instructions of Figure 6.
NOTE: If a self-contained unit is to be installed com-
pletely recessed, the front louvers must NOT be
blocked or replaced with a solid panel. The front lou-
vers allow good air circulation in the compressor com-
partment.
BMCE
49”
Fig. 4 - Front View
Model UR48DT
Showing Minimum Built-In Clearances
BLOCK
(one in each corner)
1/2”
MIN.
L
L
O
U
V
E
R
S
O
U
V
E
R
S
Fig. 6
Fig. 5
Side View
Model UR48DT
Showing Built-In Installation
Side View
Model UR48DT
Showing Free-Standing Installation
-4-
III. INSTALLATION (continued)
III. l - ELECTRICAL OUTLET INSTALLATION:
Refer to the diagram below to determine the correct location for the electrical outlet for built-in units.
3” 4” 8”
Electrical Outlet
Installation
For Model UR48DT
6”
49”
Wall Opening
NOTE: Wall location of electrical outlet for built-in units and applications that require unit to be counter top
depth, locate outlet in shaded area only.
IV. MISCELLANEOUS PRODUCT FEATURES
IV. a - SOLAR DIGITAL THERMOMETER:
All Spacesaver models are equipped with an external
solar digital thermometer. It has an LED display and
is mounted on the top, left side of the cabinet next to
the louvers.
IV. b - LIGHT SWITCHES (cont’d):
ated red switch is included for manual light control.
Typically this feature is used for units supplied with
glass doors. In the ON position, the lights are illumi-
nated whether the doors are open or not. In the OFF
position, the lights are controlled by the hinge switch
as described in the first paragraph.
Thermometers on older Spacesaver models also in-
cluded a battery back-up for use in low-light condi-
tions. Prolonged use of this in low-light conditions
could result in exhausting the battery. To replace the
battery back-up, lift-up the louver assembly as out-
lined in section V. a. Next, remove the screws secur-
ing the thermometer housing cover and replace the
battery.
IV. c - DEFOGGER CONTROL:
As environmental conditions vary, condensation may
appear on the front of your Spacesaver around the
doors. To control this, Traulsen has included a manual
defogger switch, which is mounted on the top, left side
of the cabinet next to the louvers, below the thermom-
eter.
IV. b - LIGHT SWITCHES:
All Spacesaver models include a concealed light
switch mounted in the top door hinge(s), which auto-
matically activates the interior light when the door is
opened. When the door is closed, the lights are not
operating. In addition, an exterior mounted, illumin-
When in the ON position, anti-condensate heaters
around the door perimeter are activated which help to
evaporate any condensation, and prevent it from re-
curring. This can be turned OFF when not needed in
order to save energy.
-5-
V. OPERATION
VI. CARE & MAINTENANCE
V. a - ADJUSTING THE TEMPERATURE:
VI. a - CLEANING THE CONDENSER:
The refrigeration system has been properly charged
and tested at the factory. Plug the unit into the power
outlet to determine if the compressor(s) is running. If
not, check the “ON/OFF” switches behind the louver
assembly. On a refrigerator/freezer models (UR48DT)
there are separate switches for each compartment (lo-
cated on the right side) and both must be in the ON
position.
The most important thing you can do to insure a long,
reliable service life for your Traulsen is to regularly
clean the condenser coil.
The condensing unit requires regularly scheduled
cleaning to keep the finned condenser clean of lint
and dust accumulation. The frequency of cleaning
will depend on jobsite conditions, however at least
once a month is strongly recommended. Keeping the
condenser clean allows the cabinet to operate more
efficiently and use less energy.
If, after determining that your Spacesaver unit is func-
tioning, and has had adequate time to pull-down tem-
perature, the temperature is above/below standard
ranges (34 to 38° F for refrigerators, 0 to -5° F for freez-
ers), adjust the temperature controls. This is a black
knob located behind the louver assembly along the
centerline. It can be adjusted up or down one number
at a time to raise or lower temperature.
To clean the condenser, first disconnect electrical
power to the cabinet and lift up the front louver as-
sembly. To lift this, remove the two screws located on
both sides at the bottom of the louver assembly (see
figure 7). Once the screws are removed, the panel
can be pivoted upwards allowing full access to the
front facing condenser (see figure 8). Vacuum or
brush any dirt, lint or dust from the finned condenser
coil, the compressor and other cooling system parts.
If significant dirt is clogging the condenser fins, use
compressed air to blow this clear. Care should be
taken not to bend any of the condenser fins, as this
will reduce performance and compressor life.
Fig. 7
Remove
Screws
Lower louver assembly and replace the screws to hold
it in place.
VI. b - HINGE REPLACEMENT:
Both the door and hinge can be easily removed from
the cabinet. To remove the door, remove the screw at
the bottom of the upper hinge. Inside the upper hinge
there is a small pin screw which secures the door in
place. Remove this with a flat head screwdriver and
the door can then be lifted off the hinge. To remove
the door-half of the hinge from the door, slide hinge
cover downward and then remove the three Phillips
head screws which secure the hinge in place on the
door.
Fig. 8
Lift-Up Louver
Assembly
To remove the cabinet-half of the hinge, remove the
three Phillips head screws which hold it in place. On
all units, the top hinge(s) contains a microswitch for
controlling the interior lighting.
V. b - AUTOMATIC DEFROST:
The refrigerator section operates on a “cycle defrost”
basis, which means, at the end of each refrigeration
cycle, the coil is allowed to reach 42° F and defrost
itself. This method allows for maximum efficiency of
the refrigeration system.
To reassemble the hinge reverse the previous proce-
dure.
VI. c - REPLACING THE GASKETS:
The freezer section is normally frost free and never
requires a manual defrost. When the defrost system is
operating, the compressor and fans do not run.
To remove the gasket to be replaced, grasp it firmly
by one corner and pull it out. Before attempting to
install a new gasket, both the unit and the gasket it-
self must be at room temperature. Insert the four cor-
ners first by using a rubber mallet (or hammer with a
block of wood). After the corners are properly inserted,
work your way towards the center from both ends by
WARNING: DISCONNECT ELECTRICAL POWER
SUPPLY BEFORE CLEANING ANY PARTS OF THE
UNIT.
-6-
VI. CARE & MAINTENANCE (cont’d)
VII. MISC. OPERATIONS
VI. c - REPLACING THE GASKETS (cont’d):
VII. a - ADJUSTING THE SHELVES:
gently hitting with a mallet until the gasket is com-
pletely seated in place (see figure 9 for proper gasket
For shelves mounted on pins, first select the desired
location and remove the white plastic covers in the
interior back and sides by rotating them counter-clock-
wise. Next, remove the existing shelf pins by rotating
them counter-clockwise. Install the pins in the desired
location and tighten by rotating clockwise. Make sure
the pin is securely tightened down, don’t over tighten.
Slide the shelf into its new position. Replace the white
plastic covers into the holes vacated by the shelf pins.
placement).
Inside Door Panel
Gasket Assembly
Fig. 9
Vertical Gasket
Retainer
VII. b - REMOVING THE DRAWER PANS:
For your convenience, each drawer contains two (2)
removable anodized aluminum pans. They can be re-
moved for cleaning simply by opening the drawer and
lifting them out.
NOTE: The gasket may appear too large, but if it is
installed as indicated above it will slip into place.
VI. d - CLEANING THE EXTERIOR:
VII. c - REMOVING THE DRAWERS:
Exterior stainless steel should be cleaned with warm
water, mild soap and a soft cloth. Apply with a damp-
ened cloth and wipe in the direction of the metal grain.
Prior to removing the drawers, food and pans should
be removed. The drawer is heavy and care should be
taken to keep feet clear. To remove, pull the drawer
out as far as possible. Then, lift the drawer and con-
tinue to pull until the drawer is free of the unit. To
replace, simply reverse the process.
Avoid the use of strong detergents and gritty, abra-
sive cleaners as they may tend to mar and scratch the
surface. Do NOT use cleansers containing chlorine,
this may promote corrosion of the stainless steel.
VIII. OTHER
VIII. a - SERVICE INFORMATION:
Care should also be taken to avoid splashing the unit
with water, containing chlorinated cleansers, when
mopping the floor around the unit.
Before calling for service, please check the following:
Is the electrical cord plugged in?
Is the fuse OK or circuit breaker on?
Is the power switch “ON”?
For stubborn odor spills, use baking soda and water
(mixed to a 1 TBSP baking soda to 1 pint water ratio).
VI. e - CLEANING THE INTERIOR:
For cleaning both stainless steel and anodized alumi-
num interiors, the use of baking soda as described
above is recommended. Use on breaker strips and as
well as door gaskets. All interior fittings are remov-
able without tools to facilitate cleaning.
If there is no air movement in the freezer unit, it
may be in defrost cycle. Wait 35 minutes to
see if the unit will restart.
Do the lights work?
VI. f - REPLACING THE INTERIOR LIGHT BULB:
Turn the unit OFF (the ON/OFF switch is located be-
hind the top louver panel). Next, remove the light cover
by squeezing the sides together, which releases the
tabs from the holding slots. Replace the burned out
light bulb with a similar type appliance bulb.
If after checking the above items and the unit is still
not operating properly, please contact an authorized
Traulsen service agent. A complete list of authorized
service agents was provided along with your Traulsen
unit. If you cannot locate this, you may also obtain the
name of a service agent from the Tech Service page of
To replace the light cover, squeeze the sides together
and reinsert tabs in to the holding slots and release to
lock in place.
If service is not satisfactory, please contact our in-
house service department at:
Traulsen & Co., Inc.
4401 Blue Mound Road
Fort Worth, TX 76106
(800) 825-8220
Traulsen & Co., Inc. reserves the right to change speci-
fications or discontinue models without notice.
-7-
VIII. OTHER (cont’d)
VIII. b - SPARE PARTS:
Spare or replacement parts may be obtained through
a parts supplier or one of our authorized service
agents. A complete list of authorized service agents
accompanies this manual and is also posted on our
VIII. c - WARRANTY REGISTRATION:
For your convenience, the warranties on your new
Traulsen unit may be registered with us by one of two
methods. Completing the enclosed warranty card
(shipped with the unit), or by filling out the on-line
warranty registration form located on the Technical
Service page of our website (www.traulsen.com).
IX. TROUBLE SHOOTING GUIDE
FIND YOUR PROBLEM HERE
REMEDY
1. Condensing unit fails to start.
a.
b.
Check if line has been disconnected.
Check switch behind louvers.
2. Condensing unit operates for
prolonged periods or continuously.
a.
b.
c.
Are doors closing properly?
Dirty condenser or filter. Clean properly.
Evaporator coil iced. Needs to defrost.
3. Food compartment is too warm.
a.
Thermostat setting too high, readjust
thermostat.
b.
c.
Check door gasket for proper seal.
Frequent door openings, allow adequate recovery
time.
d.
Perhaps a large quantity of food has
recently been added or the door was kept
open for a long period of time, in both
cases, allow adequate time for the cabinet
to recover its normal operating temperature.
4. Food compartment is too cold.
a.
Adjust the thermostat to a warmer
setting.
5. Condensation on the exterior surface.
a.
b.
Condensation on the exterior surface of the
unit is perfectly normal during periods of
high humidity. Turn on the defogger switch.
Check door alignment and gaskets for
proper seal.
6. Compressor hums but does not start.
7. Light bulb is not functioning.
a.
Call service.
a.
b.
Check if light bulb is burned out.
Check to see if light switch is on (if applicable).
-8-
X. WARRANTY INFORMATION
STANDARD DOMESTIC WARRANTY
TRAULSEN & CO., INC. warrants new equipment to the original purchaser, when installed within the
United States against defective material and workmanship for one (1) year from the date of original
installation. Under this warranty, TRAULSEN & CO., INC. will repair or replace, at its option, including
service and labor, all parts found to be defective and subject to this warranty. The compressor part is
warranted for an additional four (4) years. During this period TRAULSEN & CO., INC. will supply re-
placement compressor(s) if deemed defective, however, all installation, recharging and repair costs
will remain the responsibility of the owner.
This warranty does not apply to damage resulting from fire, water, burglary, accident, abuse, misuse,
transit, acts of God, attempted repairs, improper installation by unauthorized persons, and will not
apply to food loss.
THEREARE NO ORAL, STATUTORY OR IMPLIED WARRANTIESAPPLICABLE TO TRAULSEN, INCLUD-
ING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
TRAULSEN SHALL HAVE NO OBLIGATION OR LIABILITY FOR CONSEQUENTIAL OR SPECIAL DAM-
AGES, GROWING OUT OF OR WITH RESPECT TO THE EQUIPMENT OR ITS SALE, OPERATION OR
USE, AND TRAULSEN NEITHER ASSUMES NOR AUTHORIZES ANYONE ELSE TO ASSUME FOR IT
ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THE EQUIPMENT OR ITS SALE, OPERATION
OR USE OTHER THAN AS STATED HEREIN.
INTERNATIONAL COMMERCIAL WARRANTY
(for Canadian warranties see domestic US warranty)
TRAULSEN & CO., INC. warrants to the original purchaser the Refrigeration Equipment manufactured and
sold by it to be free from defects in material and workmanship under normal use and service for a period of
one (1) year from date of shipment. Under this warranty, TRAULSEN & CO., INC. will reimburse the pur-
chaser for the replacement of any part of said equipment (excluding dryers & refrigerant gas) which then
proves to be defective. This warranty is void if said equipment or any part thereof has been subject to misuse,
damage in transit, accident, negligence or alteration.
TRAULSEN’S standard warranty does not apply to Export Sales. Rather, for a period of one (1) year from
date of original installation not to exceed Fifteen (15) months from date of shipment from factory, TRAULSEN:
will replace, F.O.B. factory, any defective parts normally subject to warranty.
will not cover the cost of packing, freight or labor such costs being the sole responsibility of the dealer.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EITHER EXPRESSED OR IMPLIED AND
CONSTITUTES TRAULSEN’S FULL OBLIGATION AND LIABILITY. WARRANTIES NOT AVAILABLE ON
REMOTE MODELS.
-9-
XI. INDEX
A
N
Adjusting The Temperature
6
Nylon Netting
2
B
O
BTU’s
Built-In Installation
3
4
Outlet - Electrical
3, 4, 5
P
C
Pallet - Shipping
Pans - Drawer
Plastic Covering
Power Supply
2
7
2
3
Casters
2
5
6
6
Cleaning - The Condenser
Cleaning - The Exterior
Cleaning - The Interior
Clearance
3
R
Compressor Hold Down Provisions
Compressor - Oil
Condensate Evaporator
Condensing Unit
Cord & Plug
3
2
3
6, 8
3
Recessed Installation
Refrigerant
Remote Installation
Return Authorization
4
2
3
2
S
D
Serial Tag
Service Agents
Shelf Pins
Shelves
1
7
3, 7
3, 7
3
Damage - Freight
Defogger Control
Defrost - Automatic
Drawer
2
5
6
7
7
Solenoid Valves
Drawer Pans
T
E
Temperature - Adjustment
Thermometer
6
5
Electrical Outlet - Location
5
F
U
Fans
Freight Claim
6
2
U-Trap
3
V
G
Gaskets
6, 7
6
W
Warranty
Warranty, Registration
Wiring Diagram
9
8
H
Hinge - Replacement
I
X
Y
Z
Interior Light
Installation - Built-In
Installation - Recessed
7
4
4
J
K
Keys - Door
2
L
Legs
2
7
7
5
6
Lights - Interior
Light Cover
Light Switch
Louver Assembly
M
-10-
HOURS OF OPERATION:
Monday thru Friday 7:30 am - 4:30 pm CST
Traulsen
4401 Blue Mound Road Fort Worth, TX 76106
Phone: (800) 825-8220 Fax-Svce: (817) 740-6757
Quality Refrigeration
© 2003 Traulsen - All Rights Reserved
|