Transcend Information Network Card TS2GSD133 User Manual

TS2GSD1  
33  
Secure Digital Card  
Description  
Features  
Secure Digital Card of high capacity but economic  
cost. It is specifically designed to meet the security,  
capacity and small form factor requirements in newly  
emerging audio and video consumer electronic  
devices.Transcend Secure Digital Card can lead you  
to a colorful digital world.  
ROHS compliant product  
Operating Voltage: 2.7 ~ 3.6V  
Operating Temperature: -25 ~ 85°C  
Insertion/removal durability: 10,000 cycles  
Fully compatible with SD card spec. v1.1  
Mechanical Write Protection Switch  
Forward compatibility to MultiMediaCard Version 2.11  
Supports Copy Protection for Recorded Media(CPRM) for  
music and other commercial media  
Placement  
Form Factor: 24mm x 32mm x 2.1mm  
Front  
Back  
Pin Definition  
SD Mode  
Description  
SPI Mode  
Pin No.  
Name Type  
Name Type  
Description  
Chip Select (neg true)  
Data In  
I/O/PP3  
CS  
DI  
I
1
2
3
4
5
6
7
8
9
CD/DAT  
CMD  
VSS1  
Card Detect/Data Line [Bit3]  
Command/Response  
Supply voltage ground  
Supply voltage  
PP  
S
S
I
I
Supply voltage ground  
Supply voltage  
Clock  
VSS  
VDD  
SCLK  
VSS2  
DO  
S
VDD  
S
CLK  
Clock  
I
S
VSS2  
S
Supply voltage ground  
Supply voltage ground  
Data Out  
DAT0 I/O/PP Data Line [Bit0]  
DAT1 I/O/PP Data Line [Bit1]  
O/PP  
RSV  
RSV  
I/O/PP Data Line [Bit2]  
DAT2  
1
Transcend Information Inc.  
 
TS2GSD1  
33  
Secure Digital Card  
Bus Operating Conditions  
General  
Parameter  
Peak voltage on all lines  
All Inputs  
Symbol  
Min.  
-0.3  
Max.  
Unit  
V
Remark  
VDD+0.3  
Input Leakage Current  
All Outputs  
-10  
-10  
10  
10  
µA  
µA  
Output Leakage Current  
Power Supply Voltage  
Parameter  
Symbol  
VDD  
Min.  
2.0  
Max.  
3.6  
Unit  
V
Remark  
CMD0, 15,55,ACMD41  
commands  
Supply voltage  
Supply voltage specified in OCR register  
2.7  
3.6  
V
Except CMD0, 15,55,  
ACMD41 commands  
Supply voltage differentials (VSS1, VSS2  
)
-0.3  
0.3  
V
Power up time  
250  
ms  
From 0v to VDD Min.  
Note. The current consumption of any card during the power-up procedure must not exceed 10 mA.  
Bus Signal Line Load  
The total capacitance CL the CLK line of the SD Memory Card bus is the sum of the bus master capacitance CHOST, the bus  
capacitance CBUS itself and the capacitance CCARD of each card connected to this line:  
CL = CHOST + CBUS + Ν*CCARD  
Where N is the number of connected cards. Requiring the sum of the host and bus capacitances not to exceed 30 pF for  
up to 10 cards, and 40 pF for up to 30 cards, the following values must not be exceeded:  
Parameter  
Bus signal line capacitance  
Single card capacitance  
Symbol  
CL  
Min.  
10  
Max.  
100  
10  
Unit  
pF  
Remark  
fPP 20 MHz, 7 cards  
CCARD  
pF  
Maximum signal line inductance  
Pull-up resistance inside card (pin1)  
16  
nH  
kΩ  
fPP 20 MHz  
RDAT3  
90  
May be used for card  
detection  
Note that the total capacitance of CMD and DAT lines will be consist of CHOST, CBUS and one CCARD only since they are  
connected separately to the SD Memory Card host.  
Parameter  
Pull-up resistance  
Symbol  
RCMD, RDAT  
CL  
Min.  
10  
Max.  
100  
Unit  
kΩ  
Remark  
To prevent bus floating  
fPP 5 MHz, 21 cards  
Bus signal line capacitance  
250  
pF  
3
Transcend Information Inc.  
 
TS2GSD1  
33  
Secure Digital Card  
Bus Signal Levels  
As the bus can be supplied with a variable supply voltage, all signal levels are related to the supply voltage.  
To meet the requirements of the JEDEC specification JESD8-1A, the card input and output voltages shall be within the  
following specified ranges for any VDD of the allowed voltage range:  
Parameter  
Output HIGH voltage  
Output LOW voltage  
Input HIGH voltage  
Input LOW voltage  
Symbol  
VOH  
Min.  
Max.  
Unit  
V
Remark  
0.75* VDD  
IOH = -100 μA @VDD min  
IOL = -100 μA @VDD min  
VOL  
0.125* VDD  
VDD + 0.3  
0.25* VDD  
V
VIH  
0.625* VDD  
V
VIL  
VSS – 0.3  
V
4
Transcend Information Inc.  
 
TS2GSD1  
33  
Secure Digital Card  
Bus Timing  
Parameter  
Symbol  
Min  
Max.  
Unit  
Remark  
Clock CLK (All values are referred to min (VIH) and max (VIL)  
Clock frequency Data Transfer Mode  
Clock frequency Identification Mode  
(The low freq. is required for MultiMediaCard  
compatibility.)  
fPP  
fOD  
0
0
25  
MHz CL 100 pF, (7 cards)  
400  
KHz CL 250 pF, (21 cards)  
Clock low time  
tWL  
tWH  
tTLH  
10  
50  
10  
50  
ns  
ns  
ns  
ns  
ns  
ns  
CL 100 pF, (7 cards)  
CL 250 pF, (21 cards)  
CL 100 pF, (7 cards)  
CL 250 pF, (21 cards)  
CL 100 pF, (7 cards)  
CL 250 pF, (21 cards)  
Clock high time  
Clock rise time  
10  
50  
5
Transcend Information Inc.  
 
TS2GSD1  
33  
Secure Digital Card  
Clock fall time  
tTHL  
10  
50  
ns  
ns  
CL 100 pF, (7 cards)  
CL 250 pF, (21 cards)  
Inputs CMD, DAT (referenced to CLK)  
Input set-up time  
tISU  
tIH  
5
5
ns  
ns  
CL 25 pF, (1 cards)  
Input hold time  
CL 25 pF, (1 cards)  
Outputs CMD, DAT (referenced to CLK)  
Output Delay time  
tODLY  
0
14  
ns  
CL 25 pF, (1 cards)  
6
Transcend Information Inc.  
 
TS2GSD1  
33  
Secure Digital Card  
Reliability and Durability  
Temperature  
Operation: -25°C / 85°C (Target spec)  
Storage: -40°C (168h) / 85°C (500h)  
Junction temperature: max. 95°C  
Operation: 25°C / 95% rel. humidity  
Storage: 40°C / 93% rel. hum./500h  
Moisture and corrosion  
Salt Water Spray: 3% NaCl/35C; 24h acc. MIL STD Method 1009  
10.000 mating cycles; test procedure: tbd.  
10N  
Durability  
Bending  
Torque  
0.15N.m or +/-2.5 deg  
Drop test  
1.5m free fall  
UV light exposure  
Visual inspection  
Shape and form  
UV: 254nm, 15Ws/cm² according to ISO 7816-1  
No warp page; no mold skin; complete form; no cavities surface smoothness <=  
-0.1 mm/cm² within contour; no cracks; no pollution (fat, oil dust, etc.)  
Minimum moving force of WP witch 40gf (Ensures that the WP switch will not slide while it is inserted to the connector.)  
WP Switch cycles minimum 1000 Cycles(@Slide force 0.4N to 5N)  
Above technical information is based on industry standard data and tested to be reliable. However, Transcend makes no  
warranty, either expressed or implied, as to its accuracy and assumes no liability in connection with the use of this product.  
Transcend reserves the right to make changes in specifications at any time without prior notice.  
7
Transcend Information Inc.  
 

Toshiba Cash Register MA 68 SERIES User Manual
TRENDnet Network Router TW100 BRV304 User Manual
Tripp Lite Computer Accessories NC2003SR User Manual
Uniden Cordless Telephone DSS 7915 + 1 WP User Manual
Uniden Welder 24 148 User Manual
VDO Dayton Car Stereo System CD1537x User Manual
Verona Cooktop CTG212FD User Manual
VTech Cell Phone i6775 User Manual
Wagner SprayTech Paint Remover Paint Eater User Manual
Weed Eater Lawn Mower Accessory 532 43 46 60 User Manual