Tote Vision Computer Monitor LCD 1700VR User Manual

 
Operating Instructions  
Thank you for purchasing this high-resolution multi-scan color monitor.  
Please read this guide thoroughly before installation.  
FCC RADIO FREQUENCY INTERFERENCE STATEMENT  
WARNING: (FOR FCC CERTIFIED MODELS)  
This monitor has been tested and found compliant with the limits for a  
Class B digital device, pursuant to part 15 of the FCC Rules. These  
limits are designed to provide proper protection against harmful  
interference to a residential installation. This monitor generates, uses,  
and can radiate radio frequency energy. Harmful interference to radio  
communication may result if it is not properly installed and used.  
However, there is no guarantee that interference will not occur in a  
particular installation. If this monitor does cause serious interference  
to radio or television reception, resetting the monitor may resolve the  
problem. Moreover, users are encouraged to correct interference by  
doing one or more of the following:  
l Reposition or relocate the receiving antenna.  
l Move the monitor and the receiver further away from each other.  
l Connect the monitor into an outlet on a circuit different from that  
to which the receiver is connected.  
l Consult your local dealer or a qualified technician.  
FCC Warning:  
To assure a continued FCC compliance, a user must use a grounded  
power supply cord and the provided shielded video interface cable with  
bonded ferrite cores. Also, any unauthorized changes or modifications to  
this monitor will void the user’s authority to operate this device.  
Note: If necessary, shielded interface cables and the A.C. power cord  
must be used to meet the emission level limits.  
EMI Certification  
The Class B digital apparatus meets all requirements of the Canadian  
Interference-Causing Equipment Regulation. Cet appareil numerique de  
class B respecte toutes les exigences du Reglement sur Ic materiel  
brouilleur du Canada.  
2
 
Safety Precautions  
This monitor is manufactured and tested on the principle that the user’s  
safety comes first. However, improper use or installation may not only  
damage the monitor but endanger the user as well. As a safety  
precaution, go over the following WARNINGS carefully before installation,  
and keep this guide handy.  
Warnings:  
l
This monitor should be operated only at the correct power sources  
indicated on the label at the rear end of the monitor. If you are unsure  
of the power supply in your residence, consult your local dealer or  
Electricity Supplier.  
l
l
Do not try to repair the monitor yourself, as it contains no  
user-serviceable parts. The monitor should only be repaired by a  
qualified technician.  
Do not remove the monitor cabinet. There are high-voltage parts  
inside that may cause an electric shock even when the power cord  
is disconnected.  
l
l
l
Stop using the monitor if the cabinet is damaged. Have it checked by  
a service technician.  
Put your monitor only in a clean, dry environment. Unplug the monitor  
immediately if it gets wet, and consult your service technician.  
Always unplug the monitor before cleaning it. Clean the cabinet with  
a clean, dry cloth. Apply non-ammonia-based cleaner onto the cloth,  
not directly onto the glass screen.  
l
Keep the monitor away from magnetic objects, motors, TV sets, and  
transformers.  
l
l
Do not place heavy objects on the cable or power cord.  
For PLUG CABLE EQUIPMENT, the socket outlet should be installed  
near the equipment and should be easily accessible.  
3
 
Care and Maintenance  
Care  
l
l
l
l
Avoid exposing your monitor directly to sunlight or other heat  
sources. Place your monitor away from the sun to reduce glare.  
Put your monitor in a well-ventilated area. Do not place anything  
heavy on top of your monitor.  
Make certain that your monitor is installed in a clean and  
moisture-free area.  
Keep your monitor away from magnets, motors, transformers,  
speakers, and TV sets.  
Safety Tips  
l
If smoke, an abnormal noise or an odor comes out of your monitor,  
switch off the power immediately and call our service center.  
Never remove the rear cover of your monitor cabinet. The display  
unit inside contains high-voltage parts and may cause an electric  
shock.  
l
l
Never try to repair the monitor yourself. Always call your service  
center or a qualified technician to fix it.  
Note: This user’s manual contains graphics and information that is for  
reference purposes only and is subject to change without notice.  
4
 
CHAPTER 1  
Introduction  
BEFORE INSTALLING YOUR MONITOR  
Read this manual cover to cover.  
PAY ATTENTION to all WARNING and CAUTIONS  
DO NOT use computer components not recommend by the  
manufacture  
Do not attempt to service the monitor your self. If a problem  
occurs, contact the manufacture's authorized service center  
ABOUT YOUR MONITOR  
This monitor is a microprocessor-controlled, color monitor that  
uses a TFT LCD panel. The monitor conforms to EPA Energy  
Star and VESA DPMS (Display Power Management Signaling)  
power management standards.  
RGB MODE  
This monitor is equipped with a microprocessor that identifies  
your computer 's video mode and allows user to adjust the setting.  
VIDEO MODE  
This monitor can accept the NTSC or PAL signal to display the video  
screen automatically. It also implement the video screen on PC  
function, we called PIP function. We also provide one pair of BNC  
in/out connector inside.  
5
 
FACTORY-PRESET MODES  
Table 1 shows standard video mode setting that has been  
pre-adjusted at the factory for accurate video display. These setting  
are stored in the monitor's memory  
Table 1. Factory-Preset Modes  
PC mode  
Mode  
NEC  
VGA  
Resolution  
640x400  
640x350  
720x400  
640x480  
640x480  
640x480  
800x600  
800x600  
800x600  
800x600  
1024x768  
1024x768  
1024x768  
1280x1024  
1280x1024  
H-Freq.(KHz) V-Freq(Hz)  
24.83  
31.47  
31.47  
31.47  
37.86  
37.5  
56.4  
70  
70  
60  
72  
75  
SVGA  
35.16  
37.88  
48.08  
46.87  
48.36  
56.47  
60  
56.3  
60.3  
72.2  
75  
60  
70  
XGA  
75  
SXGA  
63.98  
80  
60  
75  
Macintosh 640x480  
832x624  
35  
49.7  
48.78  
60.241  
66.7  
74.55  
60  
1024x768  
1024x768  
74.927  
Video Mode  
NTSC  
PAL  
525 lines, 60 fields  
625 lines, 50/60 fields  
6
 
Specifications  
l
LCD-1700VR 17” LCD 8U Rack Display Monitor  
Overall Dimension(HxWxD): 394.5 x 436 x 62 mm  
Effective Display area(H/V):  
Display colors:  
Scan Frequencies:  
Horizontal  
337.92 x 270.34 mm  
16M colors  
31.47K to 80KHz  
60Hz to 75Hz  
Vertical  
Number of Pixels:  
Pixel pitch:  
1280x1024 pixels  
0.264x0.264 mm  
17" TFT LCD panel  
Picture Tube:  
Power:  
Input  
110-240VAC(auto-sensing)  
Frequency: 48-62Hz  
45Watts maximum (on)  
3 Watts (Power saving off mode)  
15pin Mini D-sub (Standard)  
1 x stereo input  
Consumption  
PC RGB Connector:  
Audio connector  
Speaker  
2W x 2  
RGB Signals:  
Video  
Analog RGB 0.7Vp-p/75W  
Sync  
Separate  
Display Data Channel:  
Compatibility  
Video connector input  
S-connector  
VESA DDC 1/2B  
x 1 (S-Video In)  
AV connector  
x 3 ( one for video  
Two for audio left/right)  
x 1 (for YcbCr/Component input)  
x 1 ( Composite Video In)  
Mini D type  
BNC connector  
Video connector output  
BNC connector  
x 1 ( Composite Video Out)  
7
 
Operations:  
User Controls  
On/Off Power Button,  
+/- and Up/down keys  
Auto adjustment, Brightness, contrast  
color temperature, Hue, Tint,  
Source select, PIP setup  
H-position, V-position, OSD position  
Audio volume, bass, treble, mute  
Load default  
On Screen Display  
Control Type:  
Compatibility:  
Digital  
IBM and compatible, Apple  
Macintosh, NEC  
Environmental Limits:  
Operating Temp  
Storage Temp.  
32° to 103°F ( 0° to 40°C )  
-4° to 140°F ( -20° to 60°C )  
10 to 85% without Condensation  
10 to 95% without Condensation  
Operating Humidity  
Storage Humidity  
8
 
Chapter 2  
PRODUCT PACKAGE  
Open the shipping carton and check the contents. If any items are  
missing or damaged, contact your dealer immediately.  
The package should include the following items  
l
l
Analog Color TFT LCD Monitor  
Accessory Box:  
1.  
2.  
3.  
4.  
5.  
6.  
VGA cable x 1  
AC to DC adapter x 1  
Power Cord x 1  
User’s manual/Warranty Card x 1  
Audio cable x 1  
Mini DIN/RCA cable (for Component Video In use)  
INSTALLING THE MONITOR  
The monitor is equipped with an auto sensing power supply for  
voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage  
designation on the rear panel of the monitor.  
11  
 
CONTROL FUNCTIONS  
The Monitor control functions are located on the lower center of the  
front view side. They are shown in the figure below and described in  
the following paragraphs.  
The control key description  
1.  
: Power Switch  
2. -  
: Decrement  
3.  
: Increment or source select  
: Move to the next item  
/ Brightness control  
: Move to the previous item  
/ Brightness control  
+
4. Ñ  
5. D  
6. MENU : Activate the on screen display  
function  
12  
 
DESCRIPTION  
1. : Power switch  
Use the power switch to turn ON or OFF power. We  
recommend turning your system power on first, then the LCD  
monitor.  
2. - & + : decrement or increment the value  
The two keys are decrement or increment the value or enter  
into the sub-menu.  
Note: The + key can change the source directly when  
de-activation OSD screen.  
3. Ñ & D : Select key / Brightness Control keys  
The two keys have two functions, controlled by the MENU key.  
When activating OSD screen, the two keys are used to select  
the wanted adjustment items. When de-activating OSD  
screen, these two keys are used to change the Brightness  
value.  
4. Menu  
Press the Menu key to activate the on screen display screen. It  
is a toggle key. Press twice to turn off the on screen display  
screen. After 30 sec idle time, the OSD screen will  
automatically turn off.  
13  
 
CHAPTER 3  
1024x768  
48.5K  
60.2  
3
Auto Adjustment  
- Execute +  
VER  
XGA-KDC45-5100  
ADJUSTING THE MONITOR  
VGA OSD main screen  
14  
 
1. Each time, when pressing the menu key, the screen will show as  
above. You can see the 3mark that means the selected item.  
Then you can change the setting through + or -.key.  
2. Pressing Sel key to move the arrow down or up. If the selected  
item has many option to choose, press – or + to enter into the  
sub-menu.  
3. Then move the Sel key to item you want to change , the item will  
be highlighted as red characters, then press – or + to change the  
value.  
4. If you finish the setting, press the MENU to key to return to the  
main OSD, then repeat the item 2 and 3 to do the changes you  
want  
The VGA main screen  
Auto adjustment  
§ Automatically adjusts the phase and position of the LCD monitor for  
the best view setting  
Color temperature setting  
§ Provide 9300K, user mode, and 6500K option  
Brightness adjustment  
§ Let user adjust the brightness. The range if from 0 to 99  
.
Contrast setup  
§ Provide user to separately adjust each R, G and B contrast and  
intensity value. When Move to this icon, and press – or + key, then the  
screen will show below  
15  
 
Color  
the  
do the  
balance  
balance:  
monitor  
white  
1024x768  
60KHz  
75Hz  
Color balance  
Intensity R  
Intensity G  
Intensity B  
Contrast R  
Contrast G  
Contrast B  
-
Execute  
+
VER  
automatically.  
XGA-KD841-5100  
Intensity R: Adjust the R color intensity, the range is from 0 to 63  
Intensity G: Adjust the G color intensity, the range is from 0 to 63  
Intensity B: Adjust the B color intensity, the range is from 0 to 63  
Contrast R: Adjust the R color contrast value, the range is from 0 to 63  
Contrast G: Adjust the G color contrast value, the range is from 0 to 63  
Contrast B: Adjust the B color contrast value, the range is from 0 to 63  
16  
 
Geometry setup  
§
§
We provide Pixel Clock, Phase, H Position, V Position, OSD H  
Position, OSD V Position and Txt/Gft option to change.  
Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99  
Phase: Adjust phase tracking to reduce the display flicker. The range  
is from 0 to 31  
§
§
§
§
§
§
H Position: Move the whole screen horizontally. The range is from 0 to  
120.  
V Position: Move the whole screen vertically. The range is from 0 to  
100.  
OSD H Position: Move the OSD horizontally. The range is from 0 to  
15  
OSD V Position: Move the OSD screen vertically. The range is from 0  
to 15  
Txt/Gfx: Select the display mode as 640x480(graphic mode) or  
720x400(text mode).  
VCR mode: To enable or disable the VCR mode. If the video source  
is come form VCR, the timing is different with DVD or camera. To  
avoid the screen shaking, you should VCR mode to enable mode.  
Normally, the default setting is OFF.  
PIP setup  
§
§
We provide H Position, V Position, PIP H/V ratio, Contrast, Intensity,  
Tint and Hue option for customer setup the PIP screen.  
H Position: Move the PIP screen Horizontally. The range is from 0 to  
15.  
§
§
V Position: Move the PIP screen Vertically. The range is from 0 to 15.  
PIP H/V ratio: Provide four option from 1 to 4. When set as 4, it is 1: 1  
ratio as original size. Set as 3, it is 1/2 of original one. Set as 2, it is  
1/4 of original one. Set as 1, it is 1/8 of original size.  
Contrast: Adjust the contrast value of PIP screen. The range is from 0  
to 127.  
§
§
Intensity: Adjust the intensity value of PIP screen. The range is from  
0to 255.  
§
§
Tint: Adjust the Tine value of PIP screen. The range is from 0 to 255.  
Hue: Adjust the Hue value of PIP screen. The range is from 0 to 255  
Source Select  
§ We provide VGA, Composite, S-video, YCbCr, PIP composite, PIP  
S-video, PIP YCbCr and PIP off for user’s selection.  
17  
 
Note: The PIP function is only valid on video on VGA screen. We can’t  
support video on video screen  
Speaker volume control  
§
§
§
§
§
§
We provide Volume, Bass, Treble, Mute and PIP audio for audio setup.  
Volume: Adjust the speaker volume. The range is from 0 to 32.  
Bass: Adjust the speaker Bass value. The range is from 0 to 10.  
Treble: Adjust the speaker Treble value. The range is from 0 to 10.  
Mute: Enable or disable the Mute function.  
PIP audio: Enable or disable the PIP mute function  
Load the factory default setting.  
§ Restore the factory default setting.  
18  
 
Chapter 4  
VIDEO ADJUSTMENT  
Video OSD Screen  
15.7K  
NTSC  
60.2  
3
Brightness  
-
Adjustment  
49  
+
VER  
XGA-KDC45-5100  
1. Each time, when pressing the menu key, the screen will show as  
above. You can see the 3mark, that means the selected item  
Then you can change the setting through + or -.key.  
2. Pressing Sel key to move the arrow down or up. If the selected  
item has many option to choose, press – or + to enter into the  
sub-menu.  
3. Then move Sel key to item you want to change, the item will be  
highlighted with red characters, then press – or + to change the  
value.  
4. If you finish the setting, press the MENU to key to the main OSD,  
then repeat the item 2 and 3.  
The OSD Main Screen  
Brightness adjustment  
§ Adjust the screen brightness value. The range if from 0 to 99.  
Contrast adjustment  
19  
 
§ Adjust the screen contrast value. The range is from 0 to 127  
Intensity adjustment  
§ Adjust the screen intensity value. The range is from 0 to 255  
Tint adjustment  
§ Adjust the screen Tint value. The range is from 0 to 127  
Hue adjustment  
§ Adjust the screen Hue value. The range is from 0 to 255  
Geometry setup  
§ We provide Sharpness, H Position, V Position, OSD H Position, and  
OSD V position.  
§ Sharpness: Adjust the screen sharpness level. The range is from 0 to  
15  
§ H position: Move the screen horizontally. The Range is from 0 to 20  
§ V Position: Move the screen vertically. The range is from 0 to 20  
§ OSD H Position: Move the OSD horizontally. The range is from 0 to 15  
§ OSD V Position: Move the OSD screen vertically. The range is from 0  
to 15  
§ VCR mode: To enable or disable the VCR mode. If the video source  
is come form VCR, the timing is different with DVD or camera. To  
avoid the screen shaking, you should VCR mode to enable mode.  
Normally, the default setting is OFF.  
Source Select  
§
we provide VGA, Composite, S-video, YCbCr source for user’s  
selection  
Speaker volume control  
§
We provide Volume, Bass, Treble, Mute and PIP audio for audio  
setup.  
§
§
§
§
§
Volume: Adjust the speaker volume. The range is from 0 to 32  
Bass: Adjust the speaker Bass value. The range is from 0 to 10  
Treble: Adjust the speaker Treble value. The range is from 0 to 10  
Mute: Enable or disable the Mute function  
PIP audio: Enable or disable the PIP mute function  
Load the factory default setting.  
Load the factory default setting  
§
20  
 
Appendix  
Troubleshooting Procedures  
This LCD Monitor was pre-adjusted in the factory with standard VGA  
timing. Due to output timing differences among various VGA cards,  
you may initially experience an unstable or unclear display when a  
new display mode or new VGA card is selected.  
This LCD Monitor Supports Multiple VGA Modes. Refer to the timing  
table for a listing of factory-preset modes supported by this LCD  
Monitor.  
PROBLEM: There is no LCD Display  
If there is no display on the LCD, please perform the following steps:  
1. Make sure that the power indicator on the LCD Monitor is lit,  
all connections are secure, and the system is running on the  
correct timing. Refer to the Addendum for information on  
timing.  
2. Turn off the LCD Monitor and then turn it back on again.  
Press the upper Function Control button (refer to Chapter 2)  
once and then press either the upper or lower Adjustment  
Control button several times. If there is still no display, press  
the other Adjustment Control button several times.  
3. If step 2 doesn’ t work, connect your PC system to another  
external CRT. If your PC System functions properly with a  
CRT Monitor but it does not function with the LCD Monitor,  
and the LCD Monitor’s power LED is blinking, the output  
timing of the PC’ s VGA card may be out of the LCD’ s  
synchronous range. Please change to an alternate mode  
listed in Addendum or replace the VGA card and repeat steps  
1 and 2.  
4. If the PC doesn’ t function with the CRT monitor neither, check  
BIOS to see if there is a dual scan setting under the display  
mode item. Set the BIOS display mode to Dual Scan or  
CRT and try again. If there is still no display, then there may  
be a problem with your system. Contact technical support.  
5. If the power LED is not lit, check to see if the AC power  
connector is securely connected. Verify that the AC adapter  
LED is lit. If the AC adapter LED is not lit, please contact  
your dealer for assistance  
21  
 

Tascam DVD Player DV W11R User Manual
Tech Craft TV Video Accessories PTV30B User Manual
TOA Electronics Cell Phone LG LX290 User Manual
Toshiba Computer Drive U2M 004GT User Manual
Toshiba DVD Player DKR40 User Manual
Toshiba Projector 260 User Manual
Tricity Bendix Oven SB 461 User Manual
Tripp Lite Surge Protector 6SPDX User Manual
Ultimate Support Systems Video Game Keyboard JS XS300 User Manual
VTech Cordless Telephone LS6115 3 User Manual