INSTRUCTION MANUAL
3 CCD COLOR CAMERA
IK-TF7P2
For Customer Use
Enter below the Serial No.
which is located on the
bottom of the cabinet. Retain
this information for future ref-
erence.
Model No.: IK-TF7P2
Serial No.:
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
USER-INSTALLER CAUTION:Your authority to operate this FCC verified equipment could be voided if
you make changes or modifications not expressly approved by the party responsible for compliance to
Part 15 of the FCC Rules.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.
Following information is only for EU-member states:
In residential areas this product may cause radio interference, therefore this product must not be used
in residential areas.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as household waste.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about the take-
back and recycling of this product, please contact your supplier where you purchased the
product or consult.
This manual is made from recycled paper.
Note the following instructions when installing.
• Do not cover the product with any material.
• Do not place the product on any confined Inflammable material such as a
carpet or blanket.
• Do not place the product in a narrow space, as this may cause heat to buildup
inside the product.
Failure to follow the above cautions may result in fire.
Do not place the product in direct sunshine and/or high temperature.
Temperature build up inside the product may result in fire.
Avoid placing in humid, smoky, vaporized or dusty places.
This may result in fire and/or electric shock.
Do not point the lens directly at the sun and/or intensive light such as
direct sunlight, etc.
Focusing of the light may cause eye injury and/or fire.
Ask your dealer to perform a periodical check and internal cleaning
(approx. once every five years).
Dust inside the product may result in fire. For check and cleaning cost, please
consult your dealer.
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by
the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-
tional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including
but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this instruction manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and carried out by
an unauthorized third party.
6. Notwithstanding the foregoing, Toshiba’s/TAIS liabilities shall not, in any circumstances, exceed
the purchase price of the product.
Copyright and Right of Portrait
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright holder.
Please also note that transfer of an image or file covered by copyright is restricted to use within the
scope permitted by the Copyright Law. Customer is responsible for complying with all copyright laws.
Protection of Personal Information
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.
3
Limitation of Usage
The product is not designed for any “critical applications.” “Critical applications” means life support
systems, exhaust or smoke extraction applications, medical applications, commercial aviation,
mass transit applications, military applications, homeland security applications, nuclear facilities or
systems or any other applications where product failure could lead to injury to persons or less of life
or catastrophic property damage. Accordingly, [Toshiba/TAIS] disclaims any and all liability arising
out of the use of the product in any critical applications.
TABLE OF CONTENTS
1. CAUTIONS ON USE AND INSTALLATION .....5
2. COMPONENTS ................................................5
3. NAMES AND FUNCTIONS ..............................6
4. CONNECTION..................................................7
( 4 ) PROCESS ..............................................22
(4. 1) Changing gamma correction........22
(4. 2) Changing master pedestal...........22
(4. 3) Changing R pedestal ...................22
(4. 4) Changing B pedestal....................22
(4. 5) Changing noise reduction ............22
( 5 ) SHADING................................................23
(5. 1) Changing V.SHAD. (Vertical Shading)
correction mode ...........................24
4. 1 Standard Connection ................................7
4. 2 Cautions on Connection............................7
4. 3 Connector Pin Assignments......................7
4. 4 How to use “EMI core” ..............................8
5. OPERATION.....................................................9
(5. 2) Changing the manual V.SHAD. (Vertical
Shading) correction setting.............24
(5. 3) Changing C.SHAD. (Corner Shading)
correction mode ...........................24
(5. 4) Changing the manual C.SHAD. (Corner
Shading) correction setting ............24
5. 1 White Balance...........................................9
5. 2 Gain ........................................................10
5. 3 Shading Correction .................................10
6. ITEMS CONTROLLED BY THE SCREEN
DISPLAY.........................................................11
( 6 ) SYNC......................................................25
(6. 1) Adjusting horizontal phase...........25
( 7 ) OPTION ..................................................25
(7. 1) Changing serial communication
baud rate......................................25
( 8 ) Returning to factory settings...................25
7. 3 Synchro. Scan Operation ........................26
( 1 ) Setting by 1H ..........................................26
( 2 ) Setting by the frame................................26
7. 4 E. TRG (External trigger) ........................27
( 1 ) 1P SNR (1 Pulse Trigger
7. MODE SETTING BY ON SCREEN DISPLAY....12
7. 1 Using the Menus.....................................12
7. 2 Menus .....................................................13
( 1 ) SHUTTER (Electronic shutter)................13
(1. 1) Changing the setting in
MANU mode.................................14
(1. 2) Changing the setting in
SS (synchro. scan) mode.............15
(1. 3) Changing the setting in
E.TRG mode................................16
(1. 3. 1) Changing the setting in
1P SNR mode...........................16
(1. 3. 2) Changing the setting in
Sync Non Reset).....................................27
(1. 1) 1 Pulse Trigger SYNC-NON
RESET Picture Output Timing .....27
( 2 ) 1P SR (1 Pulse Trigger Sync Reset).......28
(2. 1) 1 Pulse Trigger SYNC-RESET
1P SR mode .............................17
(1. 3. 3) Changing the setting in
Picture Output Timing ..................28
( 3 ) PW SNR (Pulse width trigger
PW SNR mode .........................18
(1. 3. 4) Changing the setting in
PW SR mode............................19
(1. 3. 5) Changing the setting in
RR mode...................................19
(1. 4) Changing each setting in
SYNC-NON RESET)...............................29
(3. 1) Pulse Width Trigger SYNC-NON
RESET Picture Output Timing .....29
( 4 ) PW SR (Pulse width trigger
AUTO mode .................................20
( 2 ) GAIN (Video gain)...................................20
(2. 1) Changing the setting in GAIN.......20
( 3 ) WHT BAL (White balance)......................21
(3. 1) Changing the setting in AWB
(Automatic White Balance) mode...21
(3. 2) Changing the setting in MANU
(Manual) mode.............................21
SYNC-RESET)........................................30
(4. 1) 1 Pulse Width Trigger SYNC-RESET
Picture Output Timing ..................30
( 5 ) RR (Reset restart)...................................31
(5. 1) Long Term Exposure....................31
(5. 2) Input Timing Chart Example.........31
4
7. 5 Partial Read ............................................32
( 1 ) Partial Scanning OFF
8. INPUT OUTPUT SIGNAL SPECIFICATIONS 35
9. CCD OUTPUT WAVEFORM TIMING CHART 36
10.BEFORE MAKING A SERVICE CALL...........37
11.SPECIFICATIONS ..........................................37
12.EXTERNAL APPEARANCE DIAGRAM.........38
(All pixels scanning)................................32
( 2 ) Partial Scanning ON ...............................32
( 3 ) When Partial Scanning Mode is ON .......33
7. 6 External Sync..........................................34
( 1 ) External sync signal polarity ...................34
( 2 ) External sync frequency range ...............34
( 3 ) Using the unit with external sync signal..34
(3. 1) H (horizontal) phase adjustment..34
This product is a 3CCD color camera with digital video output.
1. CAUTIONS ON USE AND INSTALLATION
• Handling the unit.
• Avoid using or storing the camera in the follow-
Do not drop, jolt, or vibrate, as this may result in
damage to the unit and may cause problems.
ing places:
Places filled with highly flammable and corrosive gas.
Treat the camera cables carefully to prevent cable
problems, such as breaks in the cable and loose
connections.
Places near gasoline, benzene, or paint thinner.
Places subject to strong vibration.
Places containing chemicals (such as pesticides),
rubber or vinyl products for extended periods of time.
• Install the camera in a location free from noise.
If the camera or the cables are located near power
utility lines or a TV, etc. undesirable noise may
appear on the screen. In such a case, try to change
the location of the camera or the cable wiring. Con-
sult with a service personnel, if the noise still appears
after changing the location or the cable wiring.
• Do not shoot intense light.
If there is an intense light at a location on the screen
such as a spot light, a blooming and smearing may
occur. When intense light enters, vertical stripes
may appear on the screen. This is not a malfunction.
Ghosts may occur when there is an intense light near
the object. In this case, change the shooting angle.
• Operating ambient temperature and humidity.
Do not use the camera in places where temperature
and humidity exceed the specifications. Picture
quality will deteriorate and internal parts may be
damaged.
• Moire
A moire pattern is an interference pattern generated
when two repetitive line patterns overlap. This is not
a malfunction. Eliminating the repetitive line patterns,
or aligning the two patterns, will eliminate the moire.
Be particularly careful when using in places exposed
to direct sunlight. When shooting in hot environ-
ments, depending on the conditions of the object and
the camera (for example when the gain is increased),
noise in the form of vertical strips or white dots may
occur. This is not a malfunction.
• Handling of the protection cap.
Keep the protection cap away from children as they
may pose a choking hazard. The protection cap
protects the image sensing plane when the lens is
removed from the camera head, do not discard.
• When not using the camera for extended periods
of time.
Switch the control unit off and disconnect the power
supply.
• When cleaning the camera.
Unplug the power source before cleaning. Clean with
a soft dry cloth only. Do not use chemicals or chemi-
cally treated cloths. Chemicals may damage coatings
and printed letters. When cleaning the lens, use lens
cleaning paper.
2. COMPONENTS
(1) Camera Control Unit......................................................................................................................1
(2) Accessories
(a) Instruction manual .................................................................................................................. 1
(b) EMI core ................................................................................................................................. 1
5
3. NAMES AND FUNCTIONS
9
2
4
DC IN 12V terminal
DISP button
1 Prism faceplate
MENU UP button
(AWB)
DISP
6
7
DATA UP (AWB) button
DATA DOWN button
MENU DATA
DC IN 12V
PAGE
5 MENU DOWN button
8
DIGITAL terminal
3 PAGE button
[ Front ]
[ Rear ]
11
10
[ Bottom ]
Prism faceplate
The protection cap is attached on the lens mount portion. After removing the cap,
mount the lens. Be careful not to scratch or touch the optical area.
DISP button
Used when switching the display.
c PAGE button
Used when switching to the menu and when selecting the menus.
Select the function to be confirmed or changed on the menu.
Select the function to be confirmed or changed on the menu.
d MENU UP button
e MENU DOWN button
f DATA UP (AWB) button Changes the value of the function selected by the MENU (UP/DOWN) button. (Also
used when using AWB.)
g DATA DOWN button
Changes the value of the function selected by the MENU (UP/DOWN) button.
h DIGITAL terminal
8-bit RGB, digital signal, and sync signals are output in the Camera Link format.
Trigger signal and external sync signal (HD, VD) are inputs.
Mode switching signal for partial scanning is input.
Accepts serial communication control signals and a DC power input (12V).
i DC IN 12V terminal
j Mounting holes M3
k Mounting holes M2
Accept a DC power input (12V).
Used to mount the camera.
Used to mount the camera.
6
4. CONNECTION
4. 1 Standard Connection
Lens
Cable (not included)
DC IN 12V
IK-TF7P2
Frame grabber board,
Monitor
Less than 4 mm
image process
equipment etc.
DC power
supply
4. 2 Cautions on Connection
• When connecting the camera cables, be sure to unplug the power source of the camera and the other equip-
ment connected to it.
• We suggest using a C mount lens made for a 3CCD color camera.
When using another lens, the best camera performance of this camera may not be obtained.
(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and flare, ghost
or shading may occur)
Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which has
projection dimension from the mounting base of less than 0.157”(4mm).
• The camera may be powered in two ways:
(1) Supplied to the DC IN 12V terminal
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved unground-
ing type AC adaptor with the specifications described below.
Power supply voltage : DC12V±10%
Current rating
Ripple voltage
Connector
: More than 830 mA
: Less than 50 mV(p–p)
: HR10A–7P–4S by HIROSE electronics Co. Ltd
Pins 1, 2 : 12V
Pins 3, 4 : GND
• For DC power supply connecting to DC IN 12V terminal, use class II DC power supply approved accord-
ing to EN60950-1 in Europe.
(2) Supplied to the DIGITAL terminal
• Supply the DC power supply (DC10V-DC13V) to pins 1 and 26 of the cable (sold separately).
• When using PoCL (power over camera link) to power the camera, use a standard PoCL cable.
* Use only one power supply type at a time.
4. 3 Connector Pin Assignments
DC IN 12V
DIGITAL
Function
I/O
–
O
O
O
O
O
I
O
I
I
I
I
1
2
3
4
+12V
1
2
3
4
5
6
7
8
9
+12V
14 GND
15 X0+
16 X1+
17 X2+
18 Xclk+
19 X3+
13
26
1
+12V
GND
GND
X0-
X1-
X2-
Xclk-
X3-
14
Connector used:
12226-51000-00
(3M) or equivalent.
1
2
3
4
SerTC+ 20 SerTC-
SerTFG- 21 SerTFG+ Serial communication control (TXD)
CC1-
Serial communication control (RXD)
22 CC1+
23 CC2-
24 CC3+
25 CC4-
26 +12V
Trigger pulse input
Partial scanning control
External HD input
External VD input
10 CC2+
11 CC3-
12 CC4+
13 GND
Connector used:
HR10A-7P-4PB
(HIROSE electronics
Co. Ltd) or equivalent.
–
7
4. 4 How to use “EMI core”
An EMI core is shipped with this camera.
When power is supplied to the DC IN terminal, this part must be used as in the drawing below.
If not used, unnecessary radio waves may be emitted.
DC IN terminal
Power cable: 2 turns
Camera
EMI core
* Mount this core as close as possible to the camera.
8
5. OPERATION
Refer to the item “ 4. CONNECTION”, connect each component correctly.
Turn on the power source of the connected equipment and the camera.
c Point the lens at the object, adjust the lens iris, focus, etc..
d Refer to the item “5.1 White Balance”, to do the adjustment.
e Refer to the items “5.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY”, select the necessary items.
5. 1 White Balance
For the white balance adjustment of this unit, AWB (Automatic White Balance) and MANU (Manual white balance)
adjustments are provided. To select the desired mode, refer to the items “7.2 (3) WHT BAL (White balance)” and “7.
MODE SETTING BY ON SCREEN DISPLAY”.
AWB
MANU
(Automatic White Balance)
(Manual White Balance)
Outline Adjust white balance by displaying a white object Adjust the white balance manually using the WHT
inside the area set by AWB menu and pressing BAL menu while shooting a white object.
the [DATA UP] button.
Note
When the shutter mode is E.TRG, AWB is not Adjustment is performed by confirming with a
available. monitor etc.
AWB (Automatic white balance)
• Set the MODE to AWB on the WHT BAL menu.
Perform the C.TEMP (color temperature conversion) setting, if necessary.
(Refer to the item “7.2 (3) WHT BAL (White balance)”.)
3200K : Appropriate for indoor shooting.
5600K : Appropriate for outdoor shooting.
• If the index menu/menu is displayed, press the [DISP] button to disable the character display on the menu.
• Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.
• The character AWB blinks on the screen when the AWB starts.
• The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1 second.
Result displayed
Meaning
AWB OK
Automatic white balance adjustment finished correctly.
AWB NG LEVEL Automatic white balance adjustment cannot be performed because the video level is too low.
LOW Set the video level propely.
AWB NG LEVEL Automatic white balance adjustment cannot be performed because the video level is too high.
HIGH
Set the video level propely.
AWB NG
C. TEMP LOW
Automatic white balance adjustment cannot be performed because the color temperature is
too low.
If the C.TEMP is set to 5600K, set to 3200K.
If the message appears with the C.TEMP set to 3200K, change the illumination or use a color
temperature conversion filter.
AWB NG
C.TEMP HIGH
Automatic white balance adjustment cannot be performed because the color temperature is
too high.
If the C.TEMP is set to 3200K, set to 5600K.
If the message appears with the C.TEMP set to 5600K, change the illumination or use the
color temperature conversion filter.
AWB NG
Automatic white balance adjustment cannot be performed because the shutter speed mode
NOT AVAILABLE is E.TRG mode.
AWB NG Automatic white balance adjustment cannot be performed for other reasons. Such as no
white area is included in an object, etc.
9
MANU (Manual white balance)
• Set the MODE to MANU on the WHT BAL menu.
(Refer to the item “7.2 (3) WHT BAL (white balance)”.)
• Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu,
confirming with a monitor etc.
(Refer to the item “7.2 (3) (3.2) Changing the setting in MANU mode”.)
5. 2 Gain
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.
For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. Select the mode on the
GAIN menu. (Refer to the item “7.2 (2) GAIN (Video gain)”.)
MANU (Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.
(Refer to the item “7.2 (2) (2.1) (a) Changing the gain in MANU mode”.)
OFF
Gain is fixed at 0 dB.
5. 3 Shading Correction
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the
screen and at the corners. In this case, the shading correction can decrease the color shading. For the shading cor-
rection of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes for V.SHAD. (Vertical
Shading) and C.SHAD. (Corner Shading) are provided. Select the mode on the SHADING menu. (Refer to the “7.2 (5)
(5.2) Changing the manual V.SHAD. (Vertical Shading) correction setting” and “7.2 (5) (5.4) Changing the manual
C.SHAD. (Corner Shading) correction setting”.)
MANU (Manual Shading)
Adjust the correction amount on the SHADING menu by confirming with a monitor or a waveform monitor.
OFF
The status is no shading correction.
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit by setting V.SHAD.
and C.SHAD. to OFF.
10
6. ITEMS CONTROLLED BY THE SCREEN DISPLAY
Preset value
(Factory setting)
Item
Available selections
MANU, SS, E. TRG, AUTO
MODE
MANU
E. TRG
1P SNR, 1P SR, PW SNR, PW SR, RR
1P SNR
OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,
1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s
MANU speed
OFF
OFF
Partial read OFF 1H/796H~795H/796H, OFF, 2FRM~512FRM
Partial read 40fps 1H/580H~579H/580H, OFF, 2FRM~512FRM
Partial read 42fps 1H/553H~552H/553H, OFF, 2FRM~512FRM
Partial read 50fps 1H/465H~464H/465H, OFF, 2FRM~512FRM
Partial read 60fps 1H/387H~386H/387H, OFF, 2FRM~512FRM
Partial read 70fps 1H/332H~331H/332H, OFF, 2FRM~512FRM
Partial read 80fps 1H/290H~289H/290H, OFF, 2FRM~512FRM
Partial read 90fps 1H/258H~257H/258H, OFF, 2FRM~512FRM
40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
Syncro.
scan.
Partial read
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps,
OFF
E.80fps, E.90fps
Trigger (1P SNR/SR)
,
Trigger (PW SNR/SR)
1P exposure time
AUTO Level
AUTO Peak/Average
MODE
,
0.01ms~30ms
-100~0~100
00:10~05:05~10:00
MANU, OFF
0dB~18dB
AWB, MANU
3200K, 5600K
-100~0~100
-100~0~100
ON, OFF
30 ms
0
05:05
OFF
0dB
AWB
3200K
0
0
OFF
0
MANU
MODE
Color temperature
MANUAL R GAIN
MANUAL B GAIN
GAMMA
Master pedestal
R pedestal
-64~0~64
-64~0~64
0
B pedestal
-64~0~64
0
NR
ON, OFF
MANU, OFF
OFF
MANU
0
V. Shading correction mode
V. Shading manual correction MANU -128~0~127
C. Shading correction mode
C. Shading manual correction
MANU R SIZE
MANU R GAIN
MANU R POSI
MANU B SIZE
MANU B GAIN
MANU B POSI
MANU, OFF
MANU
0~63
0
0
0
0
0
0
-32~0~31
-32~0~31
0~63
-32~0~31
-32~0~31
H phase adjustment
-100~0~100
0
Baud rate
9600 bps, 19200 bps
9600 bps
11
7. MODE SETTING BY ON SCREEN DISPLAY
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents
once set are memorized even if the power source is turned off, so it is unnecessary to set again when using the
unit next time. When the setting is performed, select the menu of the item to be set. (Use an appropriate monitor to
display an image with a higher signal format than XGA.)
7. 1 Using the Menus
When the power is turned on, the normal screen showing only the video signal appears. Change the output to each
screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], [MENU DOWN],
[DATA UP], and [DATA DOWN] buttons.
* A menu is selected when pushing the [PAGE] button after moving the “ ” on the screen by the [MENU UP], [MENU
DOWN] button while the Index menu is displayed.
POWER ON
Video signal output
Index menu
DISP
DISP
DISP
PAGE
PAGE
Menues
PAGE
SHADING
WHT BAL
PAGE
AWB
SHUTTER
GAIN
PROCESS
SYNC
INT
OPTION
BAUD
RATE
GAMMA
ON
V.SHAD.
MANU
PAGE
MANU
PAGE
PAGE
PAGE
MANU
SS
PAGE
GAMMA
OFF
V.SHAD.
OFF
EXT
MANU
OFF
C.SHAD.
MANU
E. TRG
1P SR
PED
MANU
C.SHAD.
OFF
E. TRG
1P SNR
NR
E. TRG
PW SR
E. TRG
PW SNR
E. TRG
RR
AUTO
12
7. 2 Menus
• Select the menu to change the setting by referring to the item “7.1 Using the Menus”.
• When the [MENU UP], [MENU DOWN] buttons are pushed, the “ ” on the screen moves up and down.
Move the “ ” to the item whose setting you wish to change.
Note:
When performing the mode setting in the menu display while selecting ON in “PART” (Partial Read: refer to
page 32) and E.TRG in “MODE”, the screen display and camera operation switch to normal mode. After closing
the MENU, it returns to the previous mode.
( 1 ) SHUTTER (Electronic shutter)
The electronic shutter has four modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger), and AUTO
(Auto Shutter).
Move the “ ” to “MODE” and push [DATA UP], [DATA DOWN] button to select the desired mode among “MANU”, “SS”,
“E.TRG”, and “AUTO”.
MANUAL
:
It is possible to select the exposure time from eleven speed setting; OFF, 1/100s, 1/250s, 1/500s,
1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/100000s.
When not using the electronic shutter, select OFF.
Note:
When setting a rapid shutter speed, sensitivity degrades according to the speed.
When a discharging light such as fluorescent lamp, etc. is used for the illumination, the flicker
may be excessive.
SS
:
:
Shutter speed can be set by the horizontal scanning time (1H) unit or by the number of frames.
E.TRG
Exposure is performed and images are output by external trigger. E.TRG includes the five modes
described below. (For details of specifications, refer to the item “7.4 E.TRG (External trigger)”.)
• 1P SNR (1 Pulse Sync Non Reset)
The charge begins to accumulate to each CCD pixels after the trigger pulse is received, and
1 frame images are output according to the internal vertical sync signal timing. The exposure/
accumulation time can be set from 0.01 to 30 ms. The trigger signal timing can be set to either the
rising or falling edge.
• 1P SR (1 Pulse Sync Reset)
The charge begins to accumulate to each CCD pixels after the trigger pulse is received.
Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output.
The exposure/accumulation time can be set from 0.01 to 30 ms. The trigger signal timing can be
set to either the rising or falling edge.
• PW SNR (Pulse width trigger Sync Non Reset)
The charge begins to accumulate to each CCD pixels after the trigger pulse is received, and 1
frame images are output according to the internal vertical sync signal timing. This is the mode to
set the exposure period by the pulse width of the trigger. The trigger signal polarity can be set to
either the positive or negative polarity.
• PW SR (Pulse width trigger Sync Reset)
The charge begins to accumulate to each CCD pixels after the trigger pulse is received.
Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output.
This is the mode to set the exposure period by the pulse width of the trigger.
The trigger signal polarity can be set to either the positive or negative polarity.
• RR (Reset restart)
Input of an external reset-restart signal permits one screen of information to be output at an arbi-
trary timing.
AUTO
:
Exposure time is automatically controlled to obtain the specified video level.
13
(1. 1) Changing the setting in MANU mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• Shutter speed setting
OFF, 100 (1/100s), 250 (1/250s), 500 (1/500s)
1000 (1/1000s), 2000 (1/2000s), 4000 (1/4000s)
10000 (1/10000s), 25000 (1/25000s)
50000 (1/50000s)100000 (1/100000s)
MODE
MANU
OUT.P
MANU
100
OFF
• Partial scanning switch（PART switch）
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
<MODE = MANUAL>
(a) Changing the shutter speed
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b) Partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.
* The preset value of partial scanning is not displayed, when OUT.P is OFF.
14
(1. 2) Changing the setting in SS (synchro. scan) mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
SHUTTER
MODE
SS
OUT.P
SS
OFF
OFF
• Shutter mode MANU, SS, E.TRG, AUTO
• Synchro. scanning setting
refer to the item "7.3 Synchro. Scan Operation".
• Partial scanning switch（PART switch）
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
<MODE = SS>
(a) Changing the shutter speed setting
aaMove the “ ” to SS by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.
(b) Partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.
* The preset value of partial scanning is not displayed, when OUT.P is OFF.
Note:
The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a characteristic of
CCD, and is not a symptom of malfunction.
15
(1. 3) Changing the setting in E.TRG mode
The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR.
First move the “ ” to MODE and select E. TRG, then move the “ ” to E.TRG and select the desired E.TRG mode.
( 1.3. 1) Changing the setting in 1P SNR mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• E.TRG mode
1P SNR, 1P SR, PW SNR, PW SR, RR
MODE
E.TRG
E.TRG
TRG.P
EXP.
1P SNR
• Input trigger pulse setting at 1P SNR and 1P SR
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
30ms
OFF
OUT.P
• Exposure time setting at 1P SNR and 1P SR
0.01 ms
0.01 ms 0.02 ms
step step
• Partial scanning switch（PART switch）
0.02 ms
0.4 ms
0.1 ms
step
1 ms
20 ms
1 ms 2 ms
step step
30 ms
<MODE = E.TRG E.TRG = 1P SNR>
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
(a) Changing the polarity of the input trigger pulse setting
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either
,
by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing 1P SNR exposure time setting
aaMove the “ ” to EXP. by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the exposure time by pushing [DATA UP], [DATA DOWN] buttons.
(c) Changing the partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.
* The preset value of partial scanning is not displayed, when OUT.P is OFF.
16
( 1.3. 2) Changing the setting in 1P SR mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• E.TRG mode
1P SNR, 1P SR, PW SNR, PW SR, RR
MODE
E.TRG
1P SR
E.TRG
TRG.P
EXP.
• Input trigger pulse setting at 1P SNR and 1P SR
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
30ms
OFF
OUT.P
• Exposure time setting at 1P SNR and 1P SR
0.01 ms
0.01 ms 0.02 ms 0.1 ms 1 ms
step step step step
• Partial scanning switch（PART switch）
0.02 ms
0.4 ms
1 ms
20 ms
30 ms
2 ms
step
<MODE = E.TRG E.TRG = 1P SR>
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
(a) Changing the polarity of the input trigger pulse setting
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either
,
, by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing 1P SR exposure time setting
aaMove the “ ” to EXP. by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the exposure time by pushing [DATA UP], [DATA DOWN] buttons.
(c) Changing the partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.
* The preset value of partial scanning is not displayed, when OUT.P is OFF.
17
( 1.3. 3) Changing the setting in PW SNR mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• E.TRG mode
MODE
E.TRG
PW SNR
1P SNR, 1P SR, PW SNR, PW SR, RR
E.TRG
TRG.P
OUT.P
• Input trigger pulse setting at PW SNR and PW SR
OFF
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
• Partial scanning switch（PART switch）
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
<MODE = E.TRG E.TRG = PW SNR>
(a) Changing the polarity of the input trigger pulse setting
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either
,
by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
caaMove “ ” to the current value by pushing [MENU UP], [MENU DOWN] buttons.
daaSelect a desired settings by pushing [DATA UP], [DATA DOWN] buttons.
* The preset value of partial scanning is not displayed, when OUT.P is OFF.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras
become: fixed pattern noise, white pixels, etc.
18
( 1.3. 4) Changing the setting in PW SR mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• E.TRG mode
MODE
E.TRG
PW SR
1P SNR, 1P SR, PW SNR, PW SR, RR
E.TRG
TRG.P
OUT.P
• Input trigger pulse setting at PW SNR and PW SR
OFF
Input trigger pulse : positive polarity
Input trigger pulse : negative polarity
• Partial scanning switch（PART switch）
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
<MODE = E.TRG E.TRG = PW SR>
(a) Changing the polarity of the input trigger pulse setting
aaMove the “ ” to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either
,
by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras
become: fixed pattern noise, white pixels, etc.
( 1.3. 5) Changing the setting in RR mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• E.TRG mode
MODE
E.TRG
OUT.P
E.TRG
RR
OFF
1P SNR, 1P SR, PW SNR, PW SR, RR
• Partial scanning switch（PART switch）
OFF, 40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
E.40fps, E.42fps, E.50fps, E.60fps, E.70fps, E.80fps, E.90fps
<MODE = E.TRG E.TRG = RR>
(a) Changing the partial scanning setting
aaMove the “ ” to OUT.P by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the mode by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The longer the storage time with extended exposures, the more visible certain characteristics of CCD cameras
become: fixed pattern noise, white pixels, etc.
19
(1. 4) Changing each setting in AUTO mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
• Shutter mode MANU, SS, E.TRG, AUTO
SHUTTER
• Auto shutter level adjustment
-100 ~ 100
MODE
LEVEL
AUTO
0
PEAK/AVE.
00:10
• Peak/Average ratio adjustment
00:10 ~ 10:00
<MODE = AUTO>
(a) Changing the AUTO shutter level
aaMove the “ ” to LEVEL by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the shutter level by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the auto shutter detection (PEAK/AVE. ratio)
aaMove the “ ” to PEAK/AVE. by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the PEAK/AVE. ratio by pushing [DATA UP], [DATA DOWN] buttons.
( 2 ) GAIN (Video gain)
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.
For the gain adjustment of the unit, MANU (Manual) and OFF (0dB) modes are provided.
aaMANU (Manual gain)
Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps.
aaOFF
Gain is fixed at 0dB.
Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between MANU and OFF.
(2. 1) Changing the setting in GAIN
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
GAIN
MODE
MANU
MANU
0dB
• Gain mode MANU, OFF
• Manual gain adjustment 0 dB to 18 dB (1 dB step)
(a) Changing the gain in MANU mode
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the manual gain by pushing [DATA UP], [DATA DOWN] buttons.
20
( 3 ) WHT BAL (White balance)
WHT BAL has two modes; AWB, MANU.
Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the two modes between AWB and
MANU.
(3. 1) Changing the setting in AWB (Automatic White Balance) mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
WHT BAL
MODE
AWB
0
0
• White balance mode (AWB, MANU)
R GAIN
B GAIN
C.TEMP
Automatically adjusting value for red gain and blue gain
are shown on the screen
3200
* These values may not be changed during AWB mode.
• Color temperature setting 3200, 5600
(a) Changing color temperature setting
aaMove the “ ” to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.
(3. 2) Changing the setting in MANU (Manual) mode
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
WHT BAL
MODE
MANU
• White balance mode AWB, MANU
• Red gain adjustment -100 to 100
• Blue gain adjustment -100 to 100
• Color temperature setting 3200, 5600
R GAIN
B GAIN
C. TEMP
0
0
3200
(a) Changing the red gain
aaMove the “ ” to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the red gain by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the blue gain
aaMove the “ ” to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the blue gain by pushing [DATA UP], [DATA DOWN] buttons.
21
( 4 ) PROCESS
• Gamma Correction (GAMMA)
Select either OFF or ON of Gamma Correction.
• Master Pedestal (M. PED)
Adjust the Pedestal level of each RGB.
• R Pedestal (R. PED)
Adjust the Pedestal level of Red.
• B Pedestal (B. PED)
Adjust the Pedestal level of Blue.
• Noise Reduction
Select either OFF or ON of Noise Reduction.
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
PROCESS
• Gamma correction ON/OFF
• Master pedestal adjustment -64 to 64
• R pedestal adjustment -64 to 64
GAMMA
M.PED
R.PED
B.PED
NR
OFF
0
0
0
OFF
• B pedestal adjustment -64 to 64
• Noise reduction ON/OFF
(4. 1) Changing gamma correction
aaMove the “ ” to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the gamma correction by pushing [DATA UP], [DATA DOWN] buttons.
(4. 2) Changing master pedestal
aaMove the “ ” to M. PED by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.
(4. 3) Changing R pedestal
aaMove the “ ” to R. PED by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.
(4. 4) Changing B pedestal
aaMove the “ ” to B. PED by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.
(4. 5) Changing noise reduction
aaMove the “ ” to NR by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the noise reduction by pushing [DATA UP], [DATA DOWN] buttons.
22
( 5 ) SHADING
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the
screen and at the corners. In this case, the shading correction can decrease the color shading. For the shading
correction of the unit, you can select among MANU (Manual shading correction) or OFF (no shading correction) for
V.SHAD. (Vertical Shading) and C.SHAD. (Corner Shading).
MANU (Manual Shading correction)
Adjust the correction amount on the SHADING menu by confirming with a monitor or a waveform monitor.
• R size (R SIZE)
Adjust the red correction area of the corner.
low
0
high
63
• R gain (R GAIN)
Adjust the red correction level. -32
low
high
31
• R position (R POSI)
Adjust the red correction area on left and right side.
• B size (B SIZE)
Left low
Right low
31
-32
Adjust the blue correction area of the corner.
• B gain (B GAIN)
Adjust the blue correction level.
• B position (B POSI)
Adjust the blue correction area on left and right side.
OFF
The status is no shading correction.
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit by setting V.SHAD
and C.SHAD. to OFF.
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
SHADING
• Vertical Shading mode setting (MANU/OFF)
• Manual Vertical Shading mode adjustment -128 to 127
• Corner Shading mode setting (MANU/OFF)
V.SHAD.
MANU
MANU
0
C.SHAD.
R SIZE
R GAIN
R POSI
B SIZE
B GAIN
B POSI
MANU
• R size adjustment
• R gain adjustment
• R position adjustment
• B size adjustment
• B gain adjustment
• B position adjustment
0 to 63
0
0
0
0
0
0
-32 to 31
-32 to 31
0 to 63
-32 to 31
-32 to 31
23
(5. 1) Changing V.SHAD. (Vertical Shading) correction mode
aaMove the “ ” to V.SHAD by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the V.SHAD. mode setting by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The alignment value for vertical shading is fixed to “0” when selecting V.SHAD. OFF.
MANU is not displayed in the menu.
(5. 2) Changing the manual V.SHAD. (Vertical Shading) correction setting
aaMove the “ ” to MANU by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the MANU V.SHAD. by pushing [DATA UP], [DATA DOWN] buttons.
(5. 3) Changing C.SHAD. (Corner Shading) correction mode
aaMove the “ ” to C.SHAD by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect the C.SHAD. mode setting by pushing [DATA UP], [DATA DOWN] buttons.
Note:
The alignment value for corner shading is fixed to “0” when selecting C.SHAD. OFF.
MANU is not displayed in the menu.
(5. 4) Changing the manual C.SHAD. (Corner Shading) correction setting
(a) Changing the red size setting
aaMove the “ ” to R SIZE by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the R size by pushing [DATA UP], [DATA DOWN] buttons.
(b) Changing the red gain setting
aaMove the “ ” to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the R gain by pushing [DATA UP], [DATA DOWN] buttons.
(c) Changing red position setting
aaMove the “ ” to R POSI by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the R position by pushing [DATA UP], [DATA DOWN] buttons.
(d) Changing blue size setting
aaMove the “ ” to B SIZE by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the B size by pushing [DATA UP], [DATA DOWN] buttons.
(e) Changing blue gain setting
aaMove the “ ” to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the B gain by pushing [DATA UP], [DATA DOWN] buttons.
(f) Changing blue position setting
aaMove the “ ” to B POSI by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the B position by pushing [DATA UP], [DATA DOWN] buttons.
24
( 6 ) SYNC
When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync)
automatically.
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
SYNC
MODE
EXT
• Sync system display
H PHASE
0
• H PHASE adjustment -100 to 100
(6. 1) Adjusting horizontal phase
aaMove the “ ” to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.
aaAdjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.
( 7 ) OPTION
(7. 1) Changing serial communication baud rate
aaMove the “ ” to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.
aaSelect either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.
Move up down
by pushing
MENU UP, DOWN
Select the desired
value by pushing
DATA UP, DOWN
OPTION
BAUD RATE
9600
• Serial baud rate setting 9600, 19200
Communication speed setting.
Set the speed to the baud rate setting
on the personal computer side.
( 8 ) Returning to factory settings
All the settings can be returned to the factory default status (preset status).
(1) If characters are displayed on the screen, press the [DISP] button to disable the character display.
(2) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed for
approx. 1 second.
25
7. 3 Synchro. Scan Operation
The shutter speed can be set by the horizontal scanning period (1H) or by the number of frames.
( 1 ) Setting by 1H
1H/796H ~ 795H/796H stands for the setting by the 1H and the shutter speed can be set by the 1H (43.05 µs).
When operating Partial Scanning or binning, the number’s listed below can be used for setting.
Partial scanning OFF
1H/796H ~ 795H/796H
1H/580H ~ 579H/580H
1H/553H ~ 552H/553H
1H/465H ~ 464H/465H
1H/387H ~ 386H/387H
1H/332H ~ 331H/332H
1H/290H ~ 289H/290H
1H/258H ~ 257H/258H
Partial scanning 40fps, E.40fps
Partial scanning 42fps, E.42fps
Partial scanning 50fps, E.50fps
Partial scanning 60fps, E.60fps
Partial scanning 70fps, E.70fps
Partial scanning 80fps, E.80fps
Partial scanning 90fps, E.90fps
( 2 ) Setting by the frame
2FRM to 512FRM stand for the setting (long period exposure) by the frame.
The video signal stored during the frame period set is output as 1 frame video image at a frame interval specified.
(Internal VD)
n
n+1
RGB data
(video interval image)
FVAL
LVAL,
DAVL
(4FRM setting)
26
7. 4 E.TRG (External trigger)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are output.
There are four modes: 1P SNR, 1P SR, PW SNR, PW SR.
( 1 ) 1P SNR (1 Pulse Trigger Sync Non Reset)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, and 1 frame images are output.
(1. 1) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing
Negative polarity mode
Trigger*1
Positive polarity mode
About 1 µs
Exposure period*2
Exposure period*2
External HD IN*1
External VD IN*1
About 1H
(Internal VD)
RGB data
(video interval image)
FVAL
LVAL,
DVAL
4
*
28H (Partial scanning OFF)
25H (Partial scanning 40fps)
27H (Partial scanning 42fps)
33H (Partial scanning 50fps)
39H (Partial scanning 60fps)
43H (Partial scanning 70fps)
46H (Partial scanning 80fps)
48H (Partial scanning 90fps)
The internal VD falling edge is within the
exposure period and thus video is not output. *3
*1: External input signal
*2: Exposure time is determined by the setting of “7. 2 (1.3) Changing the setting in E.TRG mode”.
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.
The video and FVAL/LVAL/DVAL have a paired relationship.
*4: When NR is set to ON, 1H is increased.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trigger, there
will be an effect on the video.
27
( 2 ) 1P SR (1 Pulse Trigger Sync Reset)
Charge begins to accumulate after the trigger input to CC1 of the DIGITAL terminal, the vertical sync signal is reset
and frame images are output.
(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing
Negative polarity mode
Trigger*1
Positive polarity mode
About 1 µs
Exposure period*2
Exposure completion
0 to 1H*3
(Internal VD)
RGB data
(video interval image)
FVAL
LVAL,
DVAL
4
*
28H (Partial scanning OFF)
25H (Partial scanning 40fps)
27H (Partial scanning 42fps)
33H (Partial scanning 50fps)
39H (Partial scanning 60fps)
43H (Partial scanning 70fps)
46H (Partial scanning 80fps)
48H (Partial scanning 90fps)
*1: External input signal
*2: Exposure time is determined by the setting of “7. 2 (1.3) Changing each setting in E.TRG mode”.
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchronized to
this and output.
*4: When NR is set to ON, 1H is increased.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trigger, there
will be an effect on the video.
28
( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)
The trigger input to CC1 of the DIGITAL terminal develops 1 frame images.
(3. 1) Pulse Width Trigger SYNC-NON RESET Picture Output Timing
Negative polarity mode
Positive polarity mode
Trigger*1
About 7 µs
About 1 µs
Exposure period*2
Exposure period*2
External HD IN*1
External VD IN*1
(Internal VD)
About 1H
RGB data
(video interval image)
FVAL
LVAL,
DVAL
4
*
28H (Partial scanning OFF)
25H (Partial scanning 40fps)
27H (Partial scanning 42fps)
33H (Partial scanning 50fps)
39H (Partial scanning 60fps)
43H (Partial scanning 70fps)
46H (Partial scanning 80fps)
48H (Partial scanning 90fps)
The internal VD falling edge is within the
exposure period and thus video is not output. 3
*
*1: External input signal
*2: Exposure time = Trigger pulse width + 6 µs
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.
The video and FVAL/LVAL/DVAL have a paired relationship.
*4: When NR is set to ON, 1H is increased.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trigger, there
will be an effect on the video.
29
( 4 ) PW SR (Pulse width trigger SYNC-RESET)
The trigger input to the CC1 of the DIGITAL terminal develops 1 frame images.
(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing
Negative polarity mode
Positive polarity mode
Trigger*1
About 1 µs
About 7 µs
Exposure period*2
Exposure completion
0 to 1H
3
(Internal VD)
*
RGB data
(video interval image)
FVAL
LVAL,
DVAL
4
*
28H (Partial scanning OFF)
25H (Partial scanning 40fps)
27H (Partial scanning 42fps)
33H (Partial scanning 50fps)
39H (Partial scanning 60fps)
43H (Partial scanning 70fps)
46H (Partial scanning 80fps)
48H (Partial scanning 90fps)
*1: External input signal
*2: Exposure time = Trigger pulse width + 6 µs
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchronized to
this and output.
*4: When NR is set to ON, 1H is increased.
Note:
When the next trigger is input before completion of the output of the video corresponding to the trigger, there
will be an effect on the video.
30
( 5 ) RR (Reset restart)
Input of an external reset-restart signal (CC4 of the DIGITAL terminal: External VD input) permits one screen of
information to be output at an arbitrary timing.
(5. 1) Long Term Exposure
When sufficient sensitivity is not obtained under normal operating conditions or capturing the trail of a moving object
is desired, the reset-restart function allows high-sensitivity images by extending the exposure time. To achieve this,
please input (from an external source) a VD signal that has an expanded VD pulse and VD pulse interval.
(5. 2) Input Timing Chart Example
External HD IN
External VD IN
V reset
V reset
About 1H
About 1H
(Internal VD)
Exposure period
Exposure period
Exposure period
RGB data
(video interval image)
FVAL
LVAL,
DVAL
1 frame
1 frame= 796H (Partial scanning OFF)
580H (Partial scanning 40fps)
553H (Partial scanning 42fps)
465H (Partial scanning 50fps)
387H (Partial scanning 60fps)
332H (Partial scanning 70fps)
290H (Partial scanning 80fps)
258H (Partial scanning 90fps)
Note:
External VD interval: more than 1 frame
31
7. 5 Partial Read
( 1 ) Partial Scanning OFF (All pixels scanning)
In this mode, every pixels independent signal is output from the DIGITAL connector each 1/29.2s.
Video interval
image
1/29.2s (796H)
( 2 ) Partial Scanning ON
In this mode, the pixel signal of the vertical center portion of the image is output from the DIGITAL connector.
In the E. fps mode, the partial scanning and all the pixels scanning can be switched by the DIGITAL terminal (CC2:
partial scanning control signal).
CC2
E.40fps
E.42fps
Partial scanning 42fps
All pixels scanning
E.80fps
E.50fps
Partial scanning 50fps
All pixels scanning
E.90fps
E.60fps
‘L’ Partial scanning 40fps
‘H’ All pixels scanning
Partial scanning 60fps
All pixels scanning
CC2
E.70fps
‘L’ Partial scanning 70fps
‘H’ All pixels scanning
Partial scanning 80fps
All pixels scanning
Partial scanning 90fps
All pixels scanning
Video interval
image
1/40s (580H):When 40fps is selected
1/42s (553H):When 42fps is selected
1/50s (465H):When 50fps is selected
1/60s (387H):When 60fps is selected
1/70s (332H):When 70fps is selected
1/80s (290H):When 80fps is selected
1/90s (258H):When 90fps is selected
32
( 3 ) When Partial Scanning Mode is ON
(Internal VD)
FVAL
LVAL,
DVAL
RGB data
(video interval image)
Blanking interval
Video interval Blanking interval
B
C
D
Total
A
Video period
Mode
40fps
42fps
50fps
60fps
70fps
80fps
90fps
Total A
580H
553H
465H
387H
332H
290H
258H
Blanking interval B
Video interval C
542H
Blanking interval D
25H
27H
33H
39H
43H
46H
48H
13H
14H
20H
26H
30H
33H
35H
512H
412H
322H
259H
211H
175H
33
7. 6 External Sync
When using the unit with an external sync signal, input HD and VD to CC3 and CC4 of the DIGITAL terminal.
When the external sync signal is input, the camera automatically switches its sync from the internal sync to the
external sync.
The operation is as shown below, depending on the unit’s status and how external sync signals are input.
Shutter mode
At time of SYNC-NON
RESET mode
HD input VD input
Note
N
Y
N
Y
N
Y
Y
N
Internal sync mode
External sync mode
Only V reset is applied due to VD input. Normally not used.
HD is synchronized to external, but video is not output because
there is no VD input. Normally not used.
At time of SYNC-
RESET mode
N
Y
Internal sync mode. The presence of VD is ignored, and after a
specified time after a trigger input, V reset is applied.
HD is synchronized to external. The presence of VD is ignored,
and after a specified time after a trigger input, V reset is applied.
HD is synchronized to external. Video is output due to VD input.
HD is synchronized to the inside of the camera. Video is output
due to VD input.
*
*
At time of reset restart
Y
N
Y
Y
N
Video is not output because there is no VD input. Normally not
used.
*
At time of manual
shutter
N
Y
Y
N
N
Y
N
Y
Internal sync mode
External sync mode
HD is synchronized to external. Normally not used.
Disabled
Either Y or N is permitted.
*
( 1 ) External sync signal polarity
HD: 2 to 5V(p-p) Negative
VD: 2 to 5V(p-p) Negative
( 2 ) External sync frequency range
(External sync with HD, VD)
Within ±1% (at horizontal sync frequency of 23.229 kHz)
( 3 ) Using the unit with external sync signal
When adjusting H (horizontal) phase refer to the item “7.2 (6) (6.1) Adjusting horizontal phase”.
(3. 1) H (horizontal) phase adjustment
External
Sync. signal
Observe the external sync signal and the LVAL signal output waveform
of the unit with a dual trace oscilloscope, and adjust H phase so that
Match
the H phases match.
the phase.
LVAL signal
output
34
8. INPUT OUTPUT SIGNAL SPECIFICATIONS
( 1 ) HD Input Specifications
( 2 ) VD Input Specifications
2.0µs 5.0µs
5H 21H
( 3 ) Trigger Pulse Specifications
(Positive polarity mode)
More than 2 µs
(Negative polarity mode)
More than 2 µs
( 4 ) External HD/VD Input Phase Specifications
External VD
falling edge
100
100
External HD
Unit : Clock
1 clk=33.9ns
Center
The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD fall-
ing edge) as illustrated in the above diagram.
External VD falling edge:
Please input within about 100 clock cycles of the standard center phase.
Note that V sync of the video is output with a delay of about 2H from the external VD at the time of reset-restart
and the external trigger mode.
In the normal mode:
Continuously with the HD period of 43.05 μs and VD period of 34.27 ms (partial scanning 40fps: 24.97 ms, 42fps:
23.81 ms, 50fps: 20.02 ms, 60fps: 16.66 ms, 70fps: 14.29ms, 80fps: 12.49 ms, 90fps: 11.11 ms).
Phase timing is as illustrated in the above diagram (with only the falling edge applicable).
In the reset-restart/external trigger mode:
Continuously with the HD period of 43.05 μs. VD (reset) is at an arbitrary timing with the phase of HD being within
the standard of the above diagram.
35
9. CCD OUTPUT WAVEFORM TIMING CHART
( 1 ) Horizontal Output Waveform Timing Chart
One horizontal scan interval 1270 clk
(43.05 µs)
LVAL,
DVAL
246 clk
(8.34µs)
33.9 ns
29 clk 3 clk
40 clk
164 clk
CCD
output signal
5 clk
5
clk
Optical black Horizontal transfer Dummy
portion
stop interval
pixels
Total effective pixels 1034 clk
Optical black
portion
1
Horizontal blanking interval 246 clk
*
Output video interval 1024 clk
(8.34 µs)
(34.71 µs)
RGB data
Pixel
Clock
clk=33.9 ns
(29.5 MHz)
*1: Invalid data are output during a horizontal blanking interval.
( 2 ) Vertical Output Waveform Timing Chart
796H
28H
(1205µs)
FVAL
LVAL,
DVAL
768H
CCD
output signal
1
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
Dummy
pixels
Dummy
pixels
Optical black
portion
Optical black
portion
Optical black
portion
Optical black
portion
Vertical blanking interval 28H
Vertical blanking interval 28H
(1205µs)
(1205µs)
RGB data
36
10. BEFORE MAKING A SERVICE CALL
Symptom
Items to be checked
No image
• Is the power supplied correctly?
• Is the lens iris adjusted correctly?
• Are the cables connected correctly?
• Is the shutter mode set correctly?
• Is the image process equipment set correctly?
Poor color
• Is the monitor adjusted correctly?
• Is the white balance of the camera adjusted correctly?
• Is there enough illumination?
11. SPECIFICATIONS
Power supply
DC 10V ~ DC 13.2V
Power consumption
Pick-up system
Image sensor
Approx. 3.1W (When the DC power supply is 12V)
RGB, 3CCD
1/3inch All pixels CCD
(Effective pixels Horizontal : 1034, Vertical : 779)
Scanning System
Video output pixels
Pixel clock frequency
Sync signal frequency
Sync system
Progressive scan
Horizontal pixels : 1024, Vertical : 768
29.5MHz
Horizontal : 23.229kHz, Vertical : 29.18Hz
Internal/External (Automatic switching)
F6.8 standard (2000 lx, 3000K)
14 lx (F2.2, Sensitivity + 18 dB, 3000K)
C mount (flange back : 17.526 mm in-air)
0 to 40°C (32 to 104°F)
Sensitivity
Minimum illumination
Lens mount
Ambient temperature
Ambient humidity
Weight
Less than 90%
Approx. 158g (0.338lbs)
External dimension
44 (W) x 44 (H) x 78 (D) mm
(1.73” (W) x 1.73” (H) x 3.07” (D)) (except for protruded portion)
White balance
Gain
AWB (Automatic white balance), MANUAL (Manual)
MANUAL (Manual), OFF (0 dB)
Partial scanning
Output signal
Sync signal output
40fps, 42fps, 50fps, 60fps, 70fps, 80fps, 90fps
8-bit RGB, Digital output (Camera Link format)
FVAL, LVAL, DVAL (Positive polarity)
Pixel Clock
External sync input
HD : CC3 (LVDS input) Negative polarity
VD : CC4 (LVDS input) Negative polarity
External trigger input
CC1 (LVDS input), More than 2 μs pulse width
Partial scanning control CC2 (LVDS input)
signal input
Interface
Serial data interface : Ser TC (RXD), Ser TFG (TXD)
The designs and specifications are subject to change without notice.
If any change occurs, we will revise the manual, etc.
37
12. EXTERNAL APPEARANCE DIAGRAM
Unit : mm [inch]
5
[0.20]
2-M3 Depth 3
78
[3.07]
6.3
[0.25]
12
[0.47]
44
[1.73]
19.2
[0.76]
2-M2
5
56
[2.20]
4-M3 Depth 3
[0.20]
25
[0.98]
25
[0.98]
4-M2 Depth 3
∗ inch=mm/25.4
38
39
Limited Warranty – TOSHIBA CCD Camera
The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following limited warranty
with regard to this CCD Camera ("Product"). These limited warranties apply to the Original End-User ("You").
One (1)Year Limited Warranty of Labor and Parts
ISD warrants that this Product will perform in accordance with specifications for a period of one (1) year from the date of
purchase by the Original End-User. During this one (1) year period, ISD will repair or replace the Product, if it does not
perform as warranted. In order to take advantage of this Limited Warranty, You must: (a) deliver the Product to an ISD
Authorized Service Provider ("ASP"); and (b) pay all transportation and insurance charges for shipment of the Product to the
ASP. ISD reserves the right to substitute factory refurbished parts in place of those in need of repair.
Instruction Manual (Owner’s Manual):
You should read the Instruction Manual (Owner’s Manual) thoroughly before operating this Product. Before seeking warranty
service, you should check the troubleshooting guide in the Instruction Manual (Owner’s Manual) and follow the instructions to
correct the problem.
Your Responsibilities
This Limited Warranty is subject to the following conditions:
1. You must provide the bill of sale or proof of purchase at the time that warranty service is required.
2. You must notify an ASP within thirty (30) days after You discover that the Product does not perform in accordance with
specifications during the Limited Warranty period.
3. All warranty servicing of this product must be made by an ISD Authorized Service Provider.
4. You must pack the Product in its original carton using the original packing material, then insert the original carton
containing the Product into another carton with additional packing material before shipping the Product to an ASP.
DISCLAIMERS:
ALL OTHER EXPRESS OR IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED. SOME STATES DO
NOT ALLOWTHE EXCLUSION OF IMPLIED WARRANTIES OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TOYOU.
IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTED ABOVE, YOUR SOLE AND EXCLUSIVE
REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF THE PRODUCT. IN NO EVENT WILL ISD OR ITS PARENT
COMPANY OR ANY ASP BE LIABLE TO YOU OR ANY THIRD PARTY FOR ANY DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT. THIS LIMITATION APPLIES TO DAMAGES OF ANY KIND, INCLUDING ANY
DIRECT OR INDIRECT DAMAGES, LOST PROFITS, LOST SAVINGS OR OTHER SPECIAL, INCIDENTAL, EXEMPLARY
OR CONSEQUENTIAL DAMAGES, WHETHER FOR BREACH OF CONTRACT, TORT OR OTHERWISE, OR WHETHER
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF ISD, ITS PARENT COMPANY, OR
AN ASP HAS BEEN ADVISED OFTHE POSSIBILITY OF SUCH DAMAGES OR OF ANY CLAIM BY ANY OTHER PARTY.
SOME STATES DO NOT ALLOWTHE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR SOME PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TOYOU.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE.
THIS LIMITED WARRANTY SHALL BE VOID IF THE PRODUCT OR PARTS HAVE BEEN SUBJECTED TO MISUSE,
ABUSE, ACCIDENT, IMPROPER INSTALLATION, IMPROPER MAINTENANCE, OR USE IN VIOLATION OF ISD’S
WRITTEN INSTRUCTIONS, OR WHERE THE PRODUCT HAS BEEN ALTERED OR MODIFIED WITHOUT ISD’S PRIOR
AUTHORIZATION, OR UPON THE REMOVAL OR ALTERATION OF ISD’S FACTORY SERIAL NUMBER. LABOR
SERVICE CHARGES FOR PRODUCT INSTALLATION, SET UP AND ADJUSTMENT OF CONTROLS ARE NOT
COVERED BY THIS LIMITED WARRANTY.
How to Obtain Warranty Service – Step-By-Step Procedures:
To obtain warranty service, You should:
1. Contact an ASP for warranty service within thirty (30) days after the Product fails to comply with specifications.
2. Arrange for shipment of the Product to an ASP.
3. Securely pack the Product as described above, insure the carton, and include a letter explaining the problem and a copy
of the bill of sale or proof of purchase.
4. Prepay all transportation and insurance costs.
Questions? If you have any questions, please check ISD’s Web Site for support and a current e-mail contact to where
you can send e-mails:
No person, agent, distributor, dealer, authorized service provider, or company is authorized to change, modify, or extend the
terms of this Limited Warranty in any manner whatsoever. The time within which an action must be commenced to enforce
any obligation of ISD arising under this Limited Warranty or under any statute, or law of the United States or any state thereof,
is hereby limited to one (1) year from the date You discover or should have discovered the problem. This limitation does not
apply to implied warranties arising under state law. Some states do not permit limitation of the time within whichYou may bring
an action beyond the limits provided by state law, so the above provision may not apply to You. This Limited Warranty gives
You specific legal rights and You may also have other rights which vary from state to state.
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Imaging Systems Division
9740 Irvine Boulevard, Irvine, CA 92618-1697
Copyright© 2012 Toshiba America, Inc. All rights reserved.
|