Toshiba Computer Drive SD R2612 User Manual

TOSHIBA AMERICA INFORMATION SYSTEMS  
STORAGE DEVICE DIVISION  
IRVINE, CALIFORNIA  
SD-R2612  
CD-RW/DVD-ROM COMBINATION MOBILE DRIVE  
USER MANUAL  
 
INTRODUCTION – SD-R2612  
General Features  
CD-RW disc write/rewrite at 4X – 24X  
CD-R disc write at 4X - 24X  
3-way Disc Eject (eject button, software, emergency eject hole)  
Average Access Time  
CD  
130ms  
DVD-ROM (single) 130ms  
DVD-ROM (dual)  
DVD-RAM  
150ms  
250ms  
Horizontal or Vertical Mount  
2MByte Buffer  
Playback interchangeability for CD-ROM and DVD-ROM discs  
Regionalization (RPC2 compliance) (DVD)  
BUS Interface  
ATAPI  
Format Compatibility  
CD:  
CD-DA (Red Book) - Standard Audio CD & CD-TEXT  
CD-ROM (Yellow Book Mode1 & 2) - Standard Data\  
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session  
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)  
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video Video-  
CD (White Book) - MPEG1 Video  
DVD  
DVD DVD-ROM (Book 1.02)  
DVD-Video (Book 1.1)  
DVD-R (Book 1.0, 3.9G)  
DVD-R (Book 2.0, 4.7G) - General & Authoring  
DVD+R (Version 1.0) DVD RW DVD-RAM P  
DVD+R (Version 1.0)  
DVD RW  
DVD-RAM  
1
 
Front Panel  
Figure 1.SD-R2612 CD-RW/DVD Combo Drive Front Panel  
Load disc using tray.  
Loading  
Tray  
The LED lights green or amber when the drive is operating (LED is amber when drive is  
writing.)  
Busy  
Indicator  
The Eject button is used to open the disc tray so you can install or remove a disc.  
Eject  
Button  
The emergency eject hole is to be used only when the Loading Tray will not open when  
Eject button is pressed.  
Emergency  
Eject Hole  
 
SETUP – SD-R2612  
Toshiba recommends that only trained professionals install this CD-RW/DVD-ROM Combo drive into  
your laptop/notebook.  
Installation Notes  
The SD-R2612 CD-RW/DVD-ROM Combo drive has no jumpers that need to be set  
Mounting orientation: 15° (horizontally), 15° vertically (volume control in down position), 30°  
(drive with volume control in up position).  
When mounting drive use 4 M2-PO.4 tapping holes located on the left and right sides of drive.  
When mounting drive, the tightening torque of the four screws must be even. Recommended  
screw tightening torque is 2N  
For clearance around the front bezel, it is recommended that a clearance of more than 0.8mm  
should be left in all directions.  
Software Driver  
Toshiba's SD-R2612 drive does not require any unique device drivers for Windows '98/2000/XP/NT.  
After installing your drive and re-booting, your system should recognize your drive. Win '98/2000/XP/NT  
Operating Systems support all Toshiba's ATAPI drives natively. If you prefer using DOS, download the  
ATAPI driver from our web site.  
3
 
USING THE CD-RW/DVD-ROM Combo Drive – SD-R2612  
Drive Operation  
Inserting Media  
To insert media perform the following steps:  
Figure 1.Inserting Disc  
1. Open the drive's loading tray by pressing the Eject Button and pulling out the tray.  
2. Place media disc into drive's loading tray, and lightly press down on the inner portion of the disc.  
3. Gently close the disc tray.  
Removing Media  
To remove media disc from the drive, perform the following steps:  
1. Open the loading tray by pressing the Eject Button, and pulling tray out.  
2. Grasp disc by it's outer edge, and lift out of loading tray.  
3. Gently close the loading tray.  
Usage Guidelines  
Keep the disc tray closed when not using the CD-RW/DVD-ROM Combo drive  
Do not press down on the disc tray when opening or closing it.  
Do not place objects on the disc tray  
Never use a damaged, broken, or deformed disc  
Do not press the Eject button while the drive is playing a DVD movie or accessing a disc. To  
stop a DVD movie, click Stop button in the DVD player application program  
4
 
NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of  
the disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high  
speed, causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-  
speed technology and do not indicate a problem with the drive.  
Regional Coding  
Region Protection Coding (RPC) of DVD Discs: this feature is supported on DVD Players and is used  
with DVD-Video Discs (i.e. movies). Currently, the motion picture industry has divided the world into  
different regional "zones." These regions or "zones" correlate to the regional markets into which the  
motion picture industry releases movies. Simply put, RPC Codes are placed on Movie Discs marketed  
throughout the world based on the region of the world where they are being sold. These RPC codes  
help to control and prevent the pirating of new release movies into other motion picture market regions  
prior to their true release dates within those markets.  
The SD-R2612 DVD-ROM/CD-RW drive supports the current RPC phase 2 industry specifications. This  
means that when the DVD-ROM drive ships from the factory it is set to the region for which the  
Operating System was intended. In other words the drive is set to support the Region 1 (North America)  
Operating System and will only play Region 1 (North America) DVD-Video movie discs.  
Emergency Ejection  
CAUTION: The following procedure is intended only as a last resort when  
pressing the eject button fails to open the Loading Tray.  
1. Turn computer power OFF by properly shutting down system.  
2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in as shown in the  
picture below.  
3. Loading tray will open/eject.  
Figure 2.Using Emergency Eject  
5
 
Handling Media  
DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD  
movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-  
related and can be remedied by proper handling and care of media.  
Cleaning Media  
Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc  
accessing speed.  
If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather  
from the inner side outward.  
6
 
TROUBLESHOOTING – SD-R2612  
Problem  
Solution  
Disc tray cannot be opened  
Check that there is power to drive.  
Use Emergency Eject instructions to open tray.  
Drive is not recognized by  
system  
Is the drive connected properly? Are all cables plugged in  
properly (e.g. Power Cable, Interface Cable and Audio Cables).  
Is the software driver loaded? On a step-by-step (F8) Boot of the  
system is the CD-RW/DVD-ROM Combo drive recognized?  
(BIOS / DOS reports "device driver not found" or "no valid  
drivers selected."). If not, Contact Technical Support.  
Has the CD-RW/DVD-ROM Combo drive software driver been  
corrupted by a virus. Run a Virus Scan program and repair if  
possible. Contact Technical Support if the Virus renders the CD-  
RW/DVD-ROM Combo drive software drivers not useable.  
Drive is not recognized by  
system during Boot process,  
but is recognized by the  
Operating System (i.e. XP,  
Win2000, Win98, Win NT, etc.)  
Is the CD-RW/DVD-ROM Combo drive software driver loaded?  
On a step-by-step (F8) Boot of the system is the CD-RW/DVD-  
ROM Combo drive recognized?  
(BIOS / DOS reports "device driver not found" or "no valid DVD  
drivers selected."). If not, Contact Technical Support.  
Has the Windows CD-RW/DVD-ROM Combo drive software  
driver program been corrupted by a virus. Run a Virus Scan  
program and repair if possible. Contact Technical Support if the  
Virus renders the software drivers not useable.  
BUSY Indicator LED flashes  
slowly  
The disc may be dirty Clean it with a soft damp cloth. Avoid  
cleaning the disc using a circular motion. The disc should be  
wiped in a radial direction. That is, from the inner side outward.  
The laser lens may have become cloudy or blocked by  
particulate matter. Please contact Technical Support.  
BUSY Indicator LED is  
constantly ON  
Possible Hardware Problem. Please contact Technical Support.  
DVD-ROM can not play a DVD  
in the drive or certain types of  
CD media (i.e. CD-plus, etc.)  
Is the CD-RW/DVD-ROM Combo drive driver loaded  
Is the DVD disc the correct format for the type of system that you  
are using? (i.e. on a PC an ISO9660 IBM compatible PC format  
as opposed to Apple/Mac HFS disc or UNIX disc formats which  
will not function).  
Do you have the correct software applications program/drivers  
installed to run a DVD disc?  
Has the Windows CD-RW/DVD-ROM Combo drive software  
driver program been corrupted by a virus. Run a Virus Scan  
program and repair if possible. Contact Technical Support if the  
Virus renders the software drivers not useable.  
7
 
SPECIFICATIONS –SD-R2612  
General  
Interface:  
ATAPI  
Format Compatibility  
CD:  
CD-DA (Red Book) - Standard Audio CD & CD-TEXT  
CD-ROM (Yellow Book Mode1 & 2) - Standard Data\  
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session  
CD-I /FMV (Green Book, Mode2 Form1 & 2, Ready, Bridge)  
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video  
Video-CD (White Book) - MPEG1 Video  
DVD  
DVD DVD-ROM (Book 1.02)  
DVD-Video (Book 1.1)  
DVD-R (Book 1.0, 3.9G)  
DVD-R (Book 2.0, 4.7G) - General & Authoring  
DVD+R (Version 1.0) DVD RW DVD-RAM P  
DVD+R (Version 1.0)  
DVD RW  
DVD-RAM  
Note: All DVD/CD formats, except CD-Red Book (audio), require additional application specific software  
and/or hardware. The drive is capable of reading these data formats. However, in order to run applications  
that use these formats, you must first have the required software and/or hardware.  
Data Disc Capacities  
DVD-ROM  
4.377GB (DVD-5)  
7.959GB (DVD-9)  
8.754GB (DVD-10)  
15.917GB (DVD-18)  
3.679GB  
4.377GB  
4.377GB  
DVD-R (Ver 1)  
DVD-R (Ver 2.0)  
DVD-RAM (Ver 2.1)  
CD  
656.5MB (mode 1)  
748.8MB (mode 2)  
8
 
Performance  
Transfer Rate  
DVD (Single)  
DVD (Dual)  
DVD+/-R  
DVD+/-RW  
DVD-RAM (Ver 2.1)  
CD-ROM/R (Read, Mode 1)  
CD-RW Read (Mode 1)  
10,800KB/second max (8X max)  
8,100KB/second max (6X max)  
8,100KB/second max (6X max)  
8,100KB/second max (6X max)  
5,400KB/second max (4X max)  
3,600KB/second (24X max)  
3,600KB/second (24X max)  
Random Access Time  
CD-ROM  
CD-RW  
DVD (single)  
DVD (dual)  
DVD-R/+R  
DVD-RW/+RW  
DVD-RAM  
130ms  
130ms  
130ms  
150ms  
150ms  
150ms  
250ms  
Data Error Rate  
10-15 Max  
DVD-ROM  
CD-ROM  
10-12 Max (Mode 1)  
10-9 Max (Mode 2)  
Data Buffer  
2MB  
Reliability  
MTBF  
80,000 hours  
2,000 hours/year  
42.6%  
9.3%  
31%  
Power ON Hours  
SEQ Read  
Seek  
Write  
Power ON/OFF  
Drawer Test  
7.7%  
9.3%  
Drive Lifetime  
Drawer Load/Release  
5 years  
10,000 times  
9
 
Environmental  
Ambient Temperature  
Operating  
5° to 50° C (41° to 122° F)  
-40° to 65° C (-40° to 149° F)  
Storage  
Relative Humidity  
Operating  
10% to 90%  
5% to 95% (wet bulb 40° C max)  
Storage/Shipping  
Vibration  
Operating (5 to 500 Hz) (read)  
Operating (5 to 500Hz) (write)  
Non-operating (10 to 500Hz)  
Packing (10 to 25 Hz)  
2.45 m/s2 (0.25G) (O-P)  
2.45 m/s2 (0.25G) (O-P)  
9.8 m/s2 (1.0G) (O-P)  
9.8 m/s2 (1.0G) (O-P)  
Shock (Non-operating)  
Acoustical Noise  
490 m/s2 [50G]  
40dB  
Power  
DC Voltage and Current Requirements  
+5V 5% (Operating)  
Physical  
Height  
Width  
Depth  
Weight  
0.5" (12.7mm)  
5.04" (128mm)  
5.00" (127mm)  
6.35oz (.18kg)  
Connectors  
IDE Interface Connector  
50 Pin I/F ATAPI Standard  
Regulatory  
The SD-R2612 DVD Writeable drive has been certified by the following  
regulatory agencies:  
UL 1950  
CSA C22.2 No. 950  
TUV (EN60950I)  
CE standard  
DHHS 21 CFR Sub-Chapter J  
FDA CFR21, EN60825  
10  
 
Drive Connectors –SD-R2612  
Figure 1.SD-R2612 DVD Writeable Drive Rear Panel – Connector  
A 50-pin ATAPI interface connector is found at the rear of the SD-R2612 CD-RW/DVD-  
ROM Combo drive. Connecting cable should use Japan Aviation Electronics Industry  
Limited KX14-50Series L or equivalent connector.  
ATAPI  
Connector  
Table 1.Interface Pin Assignments  
PIN  
NO.  
1
3
5
I/O SIGNAL NAME  
PIN  
NO.  
2
4
6
I/O  
SIGNAL NAME  
O
Audio L-CH  
Audio Ground  
/RESET  
O
Audio R-CH  
Digital Ground  
DD8  
DD9  
DD10  
DD11  
DD12  
DD13  
DD14  
I
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
I/O  
O
7
9
I/O DD7  
I/O DD6  
I/O DD5  
I/O DD4  
I/O DD3  
I/O DD2  
I/O DD1  
I/O DD0  
8
10  
12  
14  
16  
18  
20  
22  
24  
11  
13  
15  
17  
19  
21  
23  
DD15  
DMARQ  
/DIOR: /  
HDMARDT:  
HSTROBE  
Ground  
/DMACK  
Ground  
I
25  
27  
I
O
/DIOW:STOP  
IORDY: /  
DDMARDY:  
DSTROBE  
INTRQ  
26  
28  
I
29  
31  
33  
35  
37  
39  
41  
43  
45  
47  
49  
O
I
30  
32  
34  
36  
38  
40  
42  
44  
46  
48  
50  
O
I/O  
/IOCS16  
/PDIAG  
DA2  
DA1  
I
DA0  
I
I
I
I
I
I
/CS1FX  
/CS3FX  
I/O /DASP  
+5V (Motor)  
+5V (Motor)  
+5V (Logic)  
Ground  
Ground  
Ground  
I
I
+5V (Motor)  
+5V (Logic)  
Ground  
Ground  
I
I
CSEL  
Vendor Unique*  
I
Vendor Unique*  
*Vender Unique, don't connect pins  
11  
 

TDK Network Card VLCF Series VLCF4024 2 User Manual
Toshiba Laptop A4 User Manual
TRENDnet Network Router TEW 410APB User Manual
Tripp Lite Network Cables N002 007 WH User Manual
Tripp Lite Power Supply UPS SNMPWEBCARD User Manual
Unitech Barcode Reader MSR102 User Manual
ViewSonic Digital Photo Frame VS13442 User Manual
VocoPro Cassette Player CDG X 3 Mark II User Manual
Vulcan Hart Fryer 1ER50C User Manual
Wacom Car Video System CTL 460 User Manual