iControl® Watch
instruction guide
English
Français
Español
page 1
page 15
página 29
W240 NA 805-095003
3. Press p button, ensure iPod responds to the command correctly. If
not, remove receiver from iPod and repeat steps 2 and 3 until iPod
responds correctly.
BASIC OPERATIONS
You are now ready to wirelessly control your iPod with your watch!
VOLUME UP
OR Increase value.
Hold to increase rapidly
TIPS:
INDIGLO® BUTTON
•
Q will be visible on display in modes where iPod use is possible
(TIME, CHRONO, INTERVAL TIMER and TIMER modes).
STOP/RESET/SET
OR DONE (To save
changes and exit
setting)
NEXT TRACK
OR Proceed to next step
•
There will be a slight delay in the iPod's response to button presses
on the watch. This is normal.
VOLUME DOWN
OR Decrease value.
Hold to decrease rapidly
MODE OR NEXT
(Proceed to next step)
3 G iPod NANO & iPod CLASSIC:
•
•
•
Your iPod may exhibit a slightly longer delay when responding to
iControl® watch commands.
START/SPLIT
The volume level will not be displayed when changing volume using
your iControl® watch.
When setting, each button has a different function as indicated above.
Display indicates when button changes function.
Fast-forward or reverse through the currently playing track is not
available, therefore holding U or u watch buttons has no effect.
iPod CONTROL
•
•
It is not possible to turn your iPod off by holding p button.
The iControl® watch is designed to operate up to a range of about 10
ft. (3 m). Range will be affected by watch and iPod battery voltage. If
range is greatly reduced even with iPod fully charged, it may be nec-
essary to replace watch battery. Refer to battery change instructions
at the end of these instructions.
iPod® ICON
VOLUME UP
PREVIOUS TRACK
•
Receiver is powered by iPod, therefore use of the iControl system
will reduce time between charges for the iPod. Unplug receiver from
iPod when not using the iControl system.
(Refer to Mode
descriptions for
operation)
NEXT TRACK
VOLUME DOWN
3 G iPod NANO ONLY:
•
The backlight may cause interference with iControl® operation,
especially with backlight timer settings greater than 10 seconds.
If iControl® operation is unreliable when the backlight is on, try
reducing the Backlight Timer setting. This setting can be found in the
settings menu on the iPod.
PLAY/PAUSE
(Refer to Mode
descriptions for
operation)
GETTING STARTED WITH YOUR iControl® WATCH
iPod TOUCH ONLY
Perform these steps each time you are attaching the receiver device to
your iPod to ensure reliable operation:
1. Press MODE until watch is in TIME mode. Q will be visible on display.
•
The volume will increase or decrease two steps for each press of the
iControl® volume up (+) or volume down (–) key.
2. Plug receiver into iPod dock connector.
2
3
TIME/DATE/HOURLY CHIME
Chrono is:
START/SPLIT Button
STOP/RESET/SET Button
Reset
(00:00.00)
Press and release - START
Press and hold - p
Press and release -
Change Display Format
Press and hold - U
SETTING TIME AND DATE:
1. In TIME mode, press and hold STOP/RESET/SET. Time Zone flashes.
2. Press + or – to select Time Zone 1, 2 or 3.
Press and release - SPLIT
Press and hold - p
Press and release - STOP
Press and hold - U
Running
Stopped
3. Press NEXT to set hour. Digits flash.
4. Press + or – to change hour. Scroll through 12 hours to change to
AM/PM.
Press and release - START
Press and hold - p
Press and release - U
Press and hold - RESET
5. Press NEXT and + / – to set minutes.
All other iPod functions operate normally.
6. Press NEXT and + / – to set seconds to zero.
7. Continue pattern to set day, month, date, year, 12-hour (AM/PM) or
24-hour military time format, MM.DD or DD.MM date format, turn
hourly Chime on/off, turn Beep on/off. If you select Beep on, beep will
sound every time you push a button except INDIGLO® button.
USING THE CHRONO:
1. Press MODE until CHRONO appears.
2. Press and release START/SPLIT to start Chrono. Chrono continues to
run if you exit the mode.
8. Press NEXT to set next Time Zone, following procedure above.
9. Press DONE to exit.
3. Press and release START/SPLIT to take a split. Lap number alternates
with last two digits of display.
TIPS:
4. Display will freeze for 10 seconds. Press MODE to release display and
see running Chrono.
•
Press and hold START/SPLIT briefly to peek at next Time Zone. Press
again quickly to view 3rd time zone.
5. Press and release STOP/RESET/SET to stop or pause Chrono. Press
and release START/SPLIT to resume.
•
Press and hold START/SPLIT while next Time Zone is displayed to
change to that Time Zone. Watch will beep to confirm change.
6. When workout is completed, press and hold STOP/RESET/SET to reset
Chrono.
CHRONO
TIP: When Chrono is running, w appears in Time display.
CUSTOMIZE DISPLAY FORMAT:
Chrono counts up to 99 laps (100 hours max.) and stores 50 laps.
This determines what is shown in first and second lines of the display.
1. When Chrono is reset, press and release STOP/RESET/SET.
iPod FUNCTION IN CHRONO MODE:
p and U iPod functions share the buttons with important Chrono
functions (START/SPLIT and STOP/RESET/SET, respectively):
2. Press + / – to select LAP/SPL (Split in large digits), SPL/LAP (Lap in
large digits), or TOTAL RUN.
3. Press STOP/RESET/SET to exit.
NOTE: TOTAL RUN format allows you to view total elapsed time and
total activity time (total activity time=total elapsed time - time paused
during workout).
4
5
USING THE TOTAL RUN FEATURE IN CHRONO:
Select TOTAL RUN display format as described above.
1. Press START/SPLIT to start Chrono.
Timer is:
START/SPLIT Button
STOP/RESET/SET Button
Reset
(00:00.0)
Press and release - START
Press and hold - p
Press and release -SET
Press and hold - U
2. Press STOP/RESET/SET every time you pause/stop during your work-
out. Primary display will show time elapsed less paused time (total
activity time). Upper display will continue to run, showing total
elapsed time since Chrono was started.
Press and release - p
Press and hold - p
Press and release - STOP
Press and hold - U
Running
Stopped
Press and release - START
Press and hold - p
Press and release - RESET
Press and hold - U
TIPS:
•
When you have completed a workout in this format, total elapsed
time will continue to run until Chrono is reset.
All other iPod functions operate normally.
SETTING THE TIMER or INTERVAL TIMER
•
•
When recalling TOTAL RUN, only total activity time will be displayed.
You can set one (TIMER) or two sequential (INT TMR) Countdown Timers:
1. Press MODE until TIMER or INT TMR appears. Timer & Interval Timer
must be stopped and reset before settings can be changed.
Elapsed time counter will continue to run until Chrono is reset. If you
take a split, display will change to LAP/SPL Elapsed time is not stored
in memory.
2. Press and release STOP/RESET/SET.
[INT TMR ONLY]: INT 1 flashes.
RECALL
3. Press + / – to change hour.
1. Press MODE until RECALL appears.
4. Press NEXT and + / – to set minutes.
5. Press NEXT and + / – to set seconds.
6. Press NEXT and + / – to select STOP AT END or REPEAT AT END.
2. Press + / – to review Lap/Split times of successive laps, BEST lap,
AVG lap.
TIPS:
•
[INT TMR ONLY]: Press NEXT and then press + / – to change to INT 2
(Interval 2). Press NEXT and repeat steps 3 - 6 for INT 2.
Press STOP/RESET/SET at any time to return to viewing first Lap/Split
time.
7. Press DONE to confirm and exit.
•
•
•
You cannot view the current lap time if Chrono is running.
Recall data is cleared when Chrono is started from reset.
iPod function is not available in RECALL mode.
USING THE TIMER & INTERVAL TIMER
1. Press and release START/SPLIT to start countdown. Countdown will
continue if you exit mode.
An alarm melody chimes when countdown or interval reaches zero
or before it starts to countdown again, if set to repeat.
INTERVAL TIMER & TIMER
iPod FUNCTION IN TIMER & INTERVAL TIMER MODES:
2. Press and release STOP/RESET/SET to stop Timer.
p and U functions share the buttons with important TIMER & INT TMR
functions (START and STOP/RESET/SET, respectively):
3. Press and release START/SPLIT to continue countdown, or press and
release STOP/RESET/SET to reset.
TIPS:
•
H appears in Time display when either Timer is running.
•
Maximum number of repeats is 99.
6
7
•
•
For repeat Timer operation, repetition number appears at top right of
screen.
watch face at night and in low light conditions.
2. Continue to press up to 3 seconds to maintain illumination.
[INT TMR ONLY] When first countdown is complete, timer proceeds to
the next non-zero interval that is set. INDIGLO® night-light flashes
and beep sounds between each interval.
3. Press and hold INDIGLO® button for 4 seconds to activate NIGHT-
MODE® feature
4. In NIGHT-MODE® feature, push any button to illuminate watch face
for 3 seconds.
•
[INT TMR ONLY] If you set both Timers in Interval Timer to repeat,
Timer will countdown both intervals and then repeat entire
sequence.
5. To deactivate NIGHT-MODE® feature, press INDIGLO® button for
4 seconds. Feature will automatically deactivate after 8 hours.
ALARM
BATTERY
SETTING ALARM
Timex strongly recommends that a retailer or jeweler replace
battery. Battery type is on watch back. If present, push/short internal
reset switch after replacing battery. Battery life estimates are based on
certain assumptions regarding usage; battery life may vary depending on
actual usage.
1. Press MODE until ALM 1 appears.
2. Press STOP/RESET/SET to set alarm.
3. Hour digits flash. Press + / – to change hour.
4. Press NEXT and + / – to set minutes, AM or PM (if primary time
display is in 12-hour format), DAILY, WKDAYS or WKENDS
DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT RECHARGE.
KEEP LOOSE BATTERIES AWAY FROM CHILDREN.
5. Press DONE to confirm and exit.
To set remaining alarms, press MODE for ALM 2 or ALM 3 and set as
above.
WATER RESISTANCE
If your watch is water-resistant, meter marking or (O) is indicated.
USING ALARM
Press START/SPLIT to turn Alarm ON or OFF. w appears in display when
Water-Resistance Depth
p.s.i.a. * Water Pressure Below Surface
Alarm is ON.
30m/98ft
50m/164ft
100m/328ft
60
86
TIPS:
•
•
•
•
When Alarm is on and the set time is less than 12 hours away,
(alarm icon) appears in Time display.
160
*pounds per square inch absolute
When Alarm expires, INDIGLO® night-light and alarm icon flash and
alert sounds. Press any button to silence.
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS
ANY BUTTONS UNDER WATER.
1. Watch is water-resistant only as long as lens, push buttons and case
remain intact.
If no button is pushed, alert will cease after 20 seconds and Backup
Alarm will activate after 5 minutes.
iPod function is not available in Alarm mode.
2. Watch is not a diver watch and should not be used for diving.
INDIGLO® NIGHT-LIGHT/NIGHT-MODE® FEATURE
3. Rinse watch with fresh water after exposure to salt water.
1. Press INDIGLO® button to activate night-light. Electroluminescent
technology illuminates entire
8
9
DECLARATION OF CONFORMITY
SPECIFICATIONS
Manufacturer:
Timex Corporation
555 Christian Road
Middlebury, CT USA 06762
Operating range: 10ft
Transmission Method: Radio frequency
Frequency: 433 MHZ
declares that the product:
Battery: CR2025
Product Name:
Model Number:
Timex iControl
M805
FCC:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
conforms to the following Product Specifications:
R&TTE: 1999/05/EC
Standards:
ETSI EN 300 330-1 - V1.3.1 (EMC) & (ERM)
ETSI EN 300 330-2 - V1.1.1 (EMC) & (ERM)
Changes or modifications not expressly approved by the party responsible for compli-
ance could void the user's authority to operate the equipment.
LVD: 73/23/EEC
Standards:
CENELEC EN 60950-1
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
EMC: 89/336/EEC
Standards:
CENELEC EN 55022:1998
CENELEC EN 55024-1998
EN 61000-4-2 - ESD
EN 61000-4-3 - RF Radiated Immunity
EN 61000-4-8 - Magnetics
Supplemental Information: The product herewith complies with the requirements of
the Radio & Telecommunications Terminal Equipment Directive 1999/05/EC, the Low
Voltage Directive 73/23/EEC, and the EMC Directive 89/336/EEC and carries the 7
marking accordingly.
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Agent:
-Consult the dealer or an experienced radio/TV technician for help.
Brian J. Hudson
Director, Test Engineering and Module Development
This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
Date: 01 May, 2007, Middlebury, Connecticut, U.S.A.
10
11
TIMEX INTERNATIONAL WARRANTY
(U.S. – LIMITED WARRANTY – PLEASE SEE FRONT OF INSTRUCTION BOOKLET
FOR TERMS OF EXTENDED WARRANTY OFFER)
Your TIMEX® watch is warranted against manufacturing defects by Timex Corporation for a period
of ONE YEAR from the original purchase date. Timex and its worldwide affiliates will honor this
International Warranty.
Please note that Timex may, at its option, repair your watch by installing new or thoroughly
reconditioned and inspected components or replace it with an identical or similar model. IMPOR-
TANT — PLEASE NOTE THAT THIS WARRANTY DOES NOT COVER DEFECTS OR DAMAGES TO
YOUR WATCH:
1) after the warranty period expires;
2) if the watch was not originally purchased from an authorized Timex retailer;
3) from repair services not performed by Timex;
4) from accidents, tampering or abuse; and
5) lens or crystal, strap or band, watch case, attachments or battery. Timex may charge you for
replacing any of these parts.
THIS WARRANTY AND THE REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR PARTICULAR PURPOSE. TIMEX IS NOT LIABLE FOR ANY SPECIAL, INCIDENTAL OR CON-
SEQUENTIAL DAMAGES. Some countries and states do not allow limitations on implied warranties
and do not allow exclusions or limitations on damages, so these limitations may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from
country to country and state to state.
To obtain warranty service, please return your watch to Timex, one of its affiliates or the Timex retail-
er where the watch was purchased, together with a completed original Watch Repair Coupon or, in
the U.S. and Canada only, the completed original Watch Repair Coupon or a written statement iden-
tifying your name, address, telephone number and date and place of purchase. Please include the
following with your watch to cover postage and handling (this is not a repair charge): a US$ 8.00
check or money order in the U.S.; a CAN$7.00 cheque or money order in Canada; and a UK£2.50
cheque or money order in the U.K. In other countries, Timex will charge you for postage and han-
dling. NEVER INCLUDE A SPECIAL WATCHBAND OR ANY OTHER ARTICLE OF PERSONAL VALUE IN
YOUR SHIPMENT.
For the U.S., please call 1-800-448-4639 for additional warranty information. For Canada, call
1-800-263-0981. For Brazil, call +55 (11) 5572 9733. For Mexico, call 01-800-01-060-00. For Central
America, the Caribbean, Bermuda and the Bahamas, call (501) 370-5775 (U.S.). For Asia, call
852-2815-0091. For the U.K., call 44 020 8687 9620. For Portugal, call 351 212 946 017. For France,
call 33 3 81 63 42 00. For Germany, call 49 7 231 494140. For the Middle East and Africa, call
971-4-310850. For other areas, please contact your local Timex retailer or Timex distributor for
warranty information. In Canada, the U.S. and in certain other locations, participating Timex retailers
can provide you with a postage-paid, pre-addressed Watch Repair Mailer for your convenience in
obtaining factory service.
©2008 Timex Corporation. TIMEX and NIGHT-MODE are registered trademarks of Timex Corporation.
INDIGLO and iControl are registered trademarks of Indiglo Corporation in the US. and other
countries. iPod is a trademark of Apple, Inc., registered in the U.S. and other countries.
12
13
|