Model T020
Alarm Clock with
Month / Date / Day
Display
Thank you for purchasing this Timex model T020 Alarm Clock. Please read this
instruction manual carefully and completely to insure that you understand the
proper operation of your new alarm clock, and that you get the maximum benefit
from all the advanced features included in this model.
For additional information, online registration,
and exclusive special offers visit our website:
For questions or comments regarding this or other
products, please call our toll-free number 1-800-888-4491.
Para instruccionese en Espanol, llame al 1-800-888-4491.
Limited 90-Day Warranty Information
Timex Audio Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies),
warrants this product to be free from defects in workmanship and materials, under normal use
and conditions, for a period of 90 days from the date of original purchase.
Should service be required by reason of any defect or malfunction during the warranty period,
SDI Technologies will repair or, at its discretion, replace this product without charge (except for a
$3.00 charge for handling, packing, return UPS/postage, and insurance). This decision is subject
to verification of the defect or malfunction upon delivery of this product to the Factory Service
Center listed below. The product must include proof of purchase, including date of purchase. The
fee for service after the warranty period or without proof of purchase is $6.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh
ones, as exhausted or defective batteries are the most common cause of problems encountered.
If service is still required:
1. Remove batteries (if applicable) and pack the unit in a well-padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date
of purchase.
3. Enclose a check or money order payable to the order of Soundesign, for the sum of $3.00 (or
$6.00 if after the warranty period or without proof of purchase).
4. Send the unit prepaid to the Factory Service Center listed below:
Consumer Repair Department
SDI Technologies Inc.
Timex Audio Products Division
1330 Goodyear Dr.
El Paso, TX 79936-6420
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed.
It does not cover (i) products which have been damaged by negligence, misuse or accident, or
which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets,
or units damaged by excessive heat; (iii) damage to tape cassettes (if applicable); (iv) the cost of
shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the
product subsequent to the original purchaser. Any applicable implied warranties are also limited
to 90 days, and SDI Technologies will not be liable for consequential damages. (Some states do
not allow limitations on implied warranties or exclusion of consequential damages, so these
restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
TIMEX is a registered trademark of Timex Corporation the United States and other countries.
T020-042209-A
Printed in China
Care and Maintenance
If you notice that the time display is beginning to fade, or if it has completely disappeared,
replace the batteries. Replace both batteries at the same time and do not mix different
types of batteries. Do not leave exhausted batteries in the clock for a long period of time.
They may eventually leak and cause damage to the clock itself or to the surface the clock
is placed on.
Please dispose of the exhausted batteries properly.
Note: After replacing the batteries the clock will return to its original default settings. It
will be necessary to reset the time and alarm settings.
Controls
Snooze/Light Button
Snooze/Alarm
On/Off Button
Mode/Set Button
UP / 12/24 Button
Down Button
Controls and Their Functions
Snooze Bar – When Snooze function is activated, press to stop alarm temporarily.
After 5 minutes alarm turns ‘On’ again. Snooze operation can be repeated up to 8
times. If snooze is not activated, pressing Snooze Bar resets alarm to following day.
During normal operation, pressing the Snooze Bar also turns on the display
backlighting momentarily for nighttime viewing. After 5 seconds the lighting turns off
automatically.
MODE Button – Used to switch between time and alarm time display modes, and
to enter manual time and alarm setting modes.
/12/24 Button - Used to switch the time display between 12-hour and 24-hour
formats. Also used to manually advance the time, year, month, and date displays.
Button – Used to manually ‘back-up’ the time, year, month, and date displays.
Snooze/Alarm On/Off Button – Use to activate or deactivate the alarm and
activate or deactivate the Snooze function.
Time Display
PM Indicator
Alarm Time Indicator
Alarm Indicator
Month /
Date
Indicator
24 Hour
Indicator
Day
Time
Indicator
Display
Snooze Indicator Seconds Indicator
Preparation for Use
Installing the Batteries
Open the Battery Compartment cover by
pressing down on the locking tab. Insert 2 “AA”
batteries (not included) in the battery
compartment. Be sure to insert the batteries
according to the polarity markings ( “+” / “−“)
inside the battery compartment. If the batteries
are inserted incorrectly the unit will not work.
We recommend you use a well-known brand of
alkaline batteries for longest life and best
performance.
Operating Instructions
Setting the Clock
Selecting 12-Hour or 24-Hour Display Mode
Press the
button momentarily to switch the display between the 12-Hour and 24-Hour
format. If you select the 24-Hour format the “24H” indicator will appear in the display. In
the 24-Hour format midnight is displayed as “0:00”, 1 PM is displayed as “13:00”, 6 PM
is displayed as “18:00”, etc. The 24-Hour format is often referred to as Military Time.
In the 12-Hour format midnight is displayed as “12:00”. Noon is displayed as
“PM 12:00”. If the “PM” indicator does not appear, the time displayed is AM. There is no
AM indicator.
Setting The Time / Year / Month and Date
After you have selected the 12 or 24-Hour display format, proceed as follows:
1. Press and hold the MODE button for two seconds until the Hour digits begin flashing,
then press either the
or
buttons to set the display to the correct hour, AM
or PM. If the PM indicator does not appear the hour displayed is AM.
2. When the correct hour appears press the MODE button once to start the Minute
digits flashing, then press either the
correct minute.
or
buttons to set the display to the
3. When the correct minutes appear press the MODE button once to start the Seconds
digits flashing. If you want to set the seconds counter to “00” press either the
button once. If you do not wish to ‘zero’ the seconds, proceed to step4.
4. Press the MODE button once more to start the Year display flashing. The default
or
year is 2004. Press the
button to set the display to the correct year.
5. Press the MODE button once more to start the Month display flashing, then press
either the or buttons to set the display to the correct month.
6. Press the MODE button once more to start the Date display flashing, then press
either the
or
buttons to set the display to the correct date. Note that the
Day of theWeek indicator changes automatically as you adjust the Date display.
7. After you have completed these adjustments you may press the MODE button once
more to exit the setting mode and return to the current time display. Or if you do
nothing the display will return to the current time automatically after 15 seconds.
Note: You must complete each of the above steps and move to the next step within 15
seconds. If you do not make any adjustment within 15 seconds the clock will exit the
setting mode and return to the previously displayed information. You must then start with
Step 1 again and make sure you complete each step within 15 seconds, while the display
is flashing.
Setting the Alarm Time
1. When the correct time, month, and date are showing on the display press the MODE
button once to change the display from current time to alarm time. The initial default
alarm setting is 12:00 (AM). The “AL” indicator appears between the Hour and
Minute digits to confirm that you are in the alarm-setting mode.
2. While the display is in the alarm-setting mode press and hold the MODE button for
two seconds until the Alarm Hour digits begin flashing, then press either the
or
buttons to set the display to the desired wake-up hour, AM or PM. If the PM
indicator does not appear the hour displayed is AM.
3. When the desired wake up hour appears press the MODE button once to start the
Minute digits flashing, then press either the
to the desired wake-up minute.
or
buttons to set the display
4. When the desired wake-up time appears on the display you may press the MODE
button once more to return to the current time display. After 15 seconds the display
returns to the current time mode automatically.
5. If you wish to reconfirm the wake-up time just press the MODE button once. The
display will change from current time to alarm time. After 15 seconds the display
changes back to current time automatically.
Activating The Alarm and Snooze Functions
To turn the alarm ‘On’ press the Snooze/Alarm On/Off button on the front panel once.
The Alarm On indicator
appears in the display.
To activate the Snooze function press the Snooze/Alarm On/Off button once more.
The Snooze indicator appears in the center of the display.
At the selected wake-up time the alarm turns on automatically. The alarm begins with a
single ‘beep’ and then the frequency of the ‘beeps’ increases. The alarm continues for
two minutes, then shuts off automatically and resets itself for the same time on the
following day.
To stop the alarm sooner, press any button on the front panel. The alarm stops immediately
and resets itself for the same time on the following day.
Snooze Function
If you activated the Snooze function and the Snooze indicator appears in the display after
the alarm turns on you may press the Snooze Bar for an extra 5 minutes sleep. The alarm
will stop and then start again 5 minutes later. You may repeat the Snooze operation up
to 8 times, but after 8 times the alarm resets itself for the following day. The Snooze
indicator flashes in the display during Snooze operation.
Deactivating The Alarm and Snooze Functions
To deactivate the Alarm and Snooze functions, press the Snooze/Alarm On/Off button
until both the Alarm indicator and Snooze indicator disappear from the display.
|