14cm Fan
ATX 12V 2.2 & EPS 12V
- Tough Atomic Energy
Build for the Extreme -
Revision A 2005.09
2006 Thermaltake Technology Co.,Ltd. All Rights Reserved.
C
Toughpower 750W
Toughpower 750W
03
02
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
Please take the time in familiarize yourself with the
power supply, its connectors and the contents of this
manual before proceeding with the installation of the
power unit. You will need a Phillips crosshead
screwdriver, perhaps your PC case manual and most
certainly your motherboard manual.
-Extremely good voltage regulation ( 3%)
Most power supplies has only one group regulation choke
with three windings. However, the Toughpower takes on
a different approach. The three (+3.3V, +5V, +12V) rails
are all separate rails with individual windings. This
feature allows the rails to have a tighter load regulation
(3% or better) than the other power supplies. This
feature also helps system voltage stay steady.
Should you have any questions regarding the
aforementioned steps, please contact Thermaltake directly.
Failure to follow the proper procedures may cause severe
bodily harm or PC component damage.
-Industrial grade components (capacitor,
transformer, etc)
For Support or General Inquiries, please contact us at:
The key feature of the Toughpower is the usage of the
highest quality components possible. Therefore,
Toughpower allows the users to enjoy performance
without worrying about the reliability.
Thermaltake Technology USA
Toll Free: (800)988-1088
Email: [email protected]
-High reliability: MTBF > 120,000 hours
Toughpower features an extremely long MTBF (Mean
Time Between Failures): 120,000 hours; which goes
above and beyond all ATX specifications.
Thermaltake Europe B.V.
Tel:+31-10-409-0150
Email: [email protected]
Thermaltake Beijing Co.Ltd.
Tel:+86-10-82883159/3189 ext.16
-Extend warranty: 3 years
Email: [email protected]
With our high quality and solid circuit designs, we are
confident to provide three years of warranty instead of
the one-year industrial standard period.
Thermaltake Australia and New Zealand Pty Ltd
Tel:+613-9763-1622
Email: [email protected]
Thermaltake Japan Inc.
Email: [email protected]
Toughpower 750W
Toughpower 750W
05
04
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
2.
1
Components Check
3.
Installation
3.1 Warnings and Cautions
750W power supply unit
3.1.1 Do not pull the AC power cord when the power supply is in
use or else damage to components will result.
3.1.2 Do not store the Power Supply in a high humidity and high
temperature environment.
3.1.3 When using an ATX type power supply under testing
conditions where the power supply unit is not installed in a
PC with its components, please follow the steps below:
1)Please take a paper clip and untwist it.
2
One AC Inputpower cord
2)Make sure the power supply unit is in the "OFF" position.
3)Locate the 20 or 24 pin motherboard connector from the
power supply unit.
4)Plug one side of the paper clip into the green wire hole.
5)Plug the other side of the paper clip into any of the black
wire holes.
Mounting screws
3
4
6)Turn on the PSU to see if the power supply fans turn on.
3.1.4 High voltages exist in the power supply. Do not open the
power supply case unless you are an authorized service
technician or electrician.
User manual
3.1.5 All warrantees and guarantees shall be voided should there
be a failure to comply with any of the warnings and cautions
covered in this manual.
Toughpower 750W
Toughpower 750W
07
06
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
3.2 Installation Steps
4.
Product Specification
To prevent electrical shocks, please disconnect the power cord
4.1 Output Specification
from your existing power supply unit. Toughpower 750W PSU has
automatic Voltage Selector which will automatically change to
100V-240V.
Main Power Connector
Voltage
Color
Orange
Orange
Black
Color
Orange
Blue
Voltage
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
+3.3
+3.3
COM
V
1
13
14
15
16
17
18
19
20
21
22
23
24
+3.3
-12
V
V
2
V
Installation Steps
3
Black
Green
Black
Black
Black
N/C
COM
+5
COM
+5
COM
V
Red
4
PS_ON#
COM
3.2.1 Disconnect the power cord from your old power supply.
3.2.2 Follow your computer case manual and disassemble the case.
3.2.3 Disconnect all the power connectors from the motherboard
and from the peripheral devices such as case fans, hard
drives, floppy drives. etc.
Black
5
V
Red
6
COM
Black
7
COM
PWR_ON
+5 Vsb
+12 V3
+12 V3
Gray
8
N/C
Purple
Yellow
Yellow
Orange
9
Red
+5
+5
+5
V
V
V
10
11
12
Red
2
1
Red
3.2.4 Remove the existing power supply from your computer case
and replace it with your new Thermaltake Toughpower
750W PSU.
+3.3
V
Black
COM
3.2.5 Connect the power connectors to the motherboard and
peripheral devices (refer to the rest of this manual to match
the various one-way key-locked connectors to the
motherboard and accessories).
3.2.6 Connect the 6-pin PCI Express connector to PCI Express
graphic card if you need.
PCI Express Connector (6 pin)
Color
Signal Pin
Note: Please read the user manual supplied with your graphic card
for detail usage instructions.
Yellow
12V2DC
12V2DC
12V2DC
COM
1
2
3
4
5
6
Yellow
Yellow
Black
Black
Black
3.2.7 Close the computer case.
3.2.8 Make sure your power supply switch is on "OFF" position,
and connect the supplied power cord to your Thermaltake
Toughpower 750W PSU.
COM
COM
Toughpower 750W
Toughpower 750W
09
08
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
Floppy Disk Connector(4 pin)
Signal
+5VDC
COM
Color
Red
Pin
1
+12V connector (4 pin)
Color
Black
Signal Pin
4
3
2
1
COM
COM
1
2
3
4
Black
Black
Yellow
2
Black
COM
3
Yellow
Yellow
+12V1DC
+12V1DC
4
4
Serial ATA Power Connector (5 pin)
Color
Signal
Pin
+12V Connector (8pin)
Signal
COM
Color
Black
Pin
1
Yellow +12V4DC
1
Black
Red
COM
+5VDC
COM
2
3
4
5
6
7
8
4
3
2
1
Black
COM
2
Black
Black
COM
3
Black
COM
4
+12VDC
+12VDC
+12VDC
5
Yellow
Yellow
Yellow
6
7
Peripheral Connector (4pin)
Signal
+12V4DC
COM
Color
Yellow
Black
Black
Red
Pin
1
1
2
COM
3
4
+5VDC
4
Toughpower 750W
Toughpower 750W
11
10
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
Total Output Connector
4.2 Touhgpower 750W PSU Specification
X1
X1
X1
Features:
-Complies with ATX 12V 2.2 & EPS 12V version.
24-pin
Main Connector
8-pin +12V
Power Connector Power Connector
4-pin +12V
-SLI, CrossFire , and Dual Core CPU ready.
X8
X2
X6
X2
-Next generation four +12V rails(12V1, 12V2, 12V3, 12V4) supports
high-end graphic card and PC system (combined loading of 60A).
-Independent Voltage Circuit: offers unflappable current delivery under
heavy load and makes voltage output more stable.
-Active Power Factor Correction (PF>0.99) and high efficiency (up to 85%).
-Extremely good voltage regulation ( 3%): provides steady voltage for
system.
4-pin Peripheral
Power Connector
5-pin S-ATA
Connector
6-pin PC Express
Connector
4-pin Floppy Drive
Connector
Technology Features
SPECIFICATION
-Industrial grade components
W0117
750 Watts
Black
P/N
Maximum Power
Color
(capacitor, transformer, etc)
-High reliability:
MTBF>120,000 hours.
-Mirror effect housing and
reliable 14cm ball-bearing
fan.
Mirror Effect
Housing
Quad +12V Rails and EPS Structure
ATX Logic on-off additional power
rocker switch
Switches
PFC
(Power Factor
Correction)
Active PFC
-Protections: Over Current,
Over Voltage, and
Noise Preventive Silicon Pad -Effectively
reduces vibration noise by as muchas 80%
Six S-ATA
Connectors
Silent 140mm Fan
14cm Fan
Short-Circuit protection.
-Safety / EMI Approvals: CE,
CB, TUV, FCC, UL, CUL, and
BSMI certified.
SPEED: 1900 RPM(+10%~-10%)
Cable Application
Cooling System
DIMENSION: 140
X
140
X
25 mm
AIR FLOW: 82 CFM
TEMP. AUTO CONTROL
Intelligent Cable Management:
All cables withblack cable sleeving
Optimum air-flow in thechassis
16 dBA at 1300 RPM
100-500 ms
Noise
P. G. Signal
Over Voltage
Protection
Recycle AC
to Reset
+5V 7.0 Vmax
+3.3V 4.5 Vmax
+12V 15.6 Vmax
DIMENSIONS
Unit Size
OUTPUT
16cm(L)x15cm(W)x8.5cm(H)
2.6 kg
Net Weight
Voltage
+5V
28A
2.0A
-
+12V1
18A
1.0A
-
+12V2
18A
1.0A
-
+12V3
18A
1.0A
-
+12V4
18A
1.0A
-
12V
0.8A
0A
+5VSB
3.0A
0A
+3.3V
30A
0.5A
-
INPUT
Max.
Load
Input Voltage
90VAC
47
-
264VAC
63 Hz
Min.
Load
Input
Frequency
Range
-
Reak
Load
-
3.5A
100VAC
200VAC
/
/
10A max.
5A max.
Input Current
Load
Reg.
+3%
- 3%
+3% +3%
- 3%
+3% +3%
- 3 %
+3%
- 3 %
+9%
- 5%
+5%
- 3%
- 3 %
- 3 %
Hold-up Time
Efficiency
16 ms
Ripple
50
mV
50
mV
120
mV
120
mV
120
mV
120
mV
120
mV
50
mV
&
Noise
up to 85%
Toughpower 750W
Toughpower 750W
13
12
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
4.3 Other Specification
4.4.3 Short Protection
All output to GND.
4.3.1 Inrush Current:
55A max. when AC input 115Vac at 25oC cold start.
110A max. when AC input 230Vac at 25oC cold start.
4.5 Environment:
4.3.2 Power Efficiency:
4.5.1 Operating Temp. 10oC to +40oC (+50oC for 750W series)
4.5.2 Storage Temp. -20oC to +70oC
80% (min.),up to 85%
115VAC - Full load 80%
230VAC - Full load 85%
4.5.3 Operating Humidity20% to 90%, non-condensing
4.5.4 Storage Humidity5% to 95%, non-condensing
4.5.5 Operating Altitude0 to 10,000 feet
4.3.3 Power Factor:
PF>0.9
4.5.6 Storage Altitude0 to 50,000 feet
4.3.4 Note:
The continuous total output power is 750W max.
The combined power of +5V and +3.3V is 180W max.
Peak currents may last up to 12 seconds with not more
than one occurrence per minute.
4.6 Hi-Pot:(Input/Output isolation)
Total combined +12V output load not exceed 60A.
4.6.1 Primary to Secondary
4242Vdc for 1 minute
4.6.2 Insulation Resistance
Primary toear thground 500Vdc, 50M ohms Min.
4.3.5 Hold-Up Time:
16msec (minimum) at 80% of full load at 230Vac input.
4.3.6 Power Good Delay:
100-500 msec.
4.3.7 Power Fail Delay:
>1 msec.
4.7 CE Requirements
4.7.1 ConductedEMI
1. Meet FCC: ClassB
2. Meet CISPR 22:Cla ssB
3. Meet BSMI: ClassB
4.7.2 SafetyStandards
1. Meet CUL (UL 60950)
2. Meet TUV EN60950
3. Meet CB (IEC 950)
4. Meet CE
4.3.8 Turn-On Delay Time:
2000 msec max.
4.3.9 Rise Time:
20ms max at full load.
4.4 Protection
When OCP,OVP or short protectionis triggered, the mainoutputs will
be latched off.The main outputs canbe reset by cyclingthe DC remote
on/off or AC power. +5Vsb output isauto recovery when fault
condition removed.
5. Meet CCC
4.7.3 Harmonic
MeetIEC1000-3- 2,Class D
4.7.4 MTBFat 25OC(demonstrated)
Over 120Khr s
4.4.1 Over CurrentProtection
Not over 240VA for every output voltage.
4.4.2 Over VoltageProtection
+3.3V output 4.5 Vmax
+5.0V output 7.0Vmax
+12.0V output 15.6 Vmax
Toughpower 750W
Toughpower 750W
15
14
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
5.
Trouble Shooting
6.
Cable Retail Package(Optional)
Condition 1:
No DC output. The fan or fans are motionlessCheck:
1-1 Is the AC inlet plug firmly plugged into the PSU inlet
socket?
P/N:A2169 PSU Adaptor Cable
Specification
1-2 Is the wall socket, extension power cord, power strip
or surge protector in use, fully functional and wall power
switch turned 'ON'?
(A)
(B)
Model
Adaptor Cable
Adaptor Cable
1-3 Is the Main Board socket (24pin) plug fully and firmly
inserted?
Dimension
(mm)
193mm
198mm
Connector
type
4pin - 8pin
20pin - 24pin
Condition 2:
The fan or fans began rotating and then stopped. The system
Cable
sleeving
color
Red
Black
hangs without proceeding any further.
Check:
Material
Weight
Voltage
Plastic
16 g
Plastic
58 g
2-1 Are the peripheral connectors firmly plugged into
accessory devices, such as the main hard drive, CD ROM
, etc?
3.3V,5V,+12v,-12V
12 V
2-2 If a plug has been inadvertently connected in an off-set or
reversed position, unplug the AC power source, reconnect
the offending connectors and then wait for 30 seconds
before replug in the AC power source and try again.
(A)4pin-8pin
(B)20pin-24pin
Note:
If the power supply still cannot or is still unable to power up
after following the above instruction, please send the unit back
to your dealer or retailer for after sales service.
Toughpower 750W
Toughpower 750W
17
16
ATX 12V 2.2 & EPS 12V Version
ATX 12V 2.2 & EPS 12V Version
Note
Note
|