User's Guide
SLOU308–January 2011
TPA6139A2 EVM
This section provides an overview of the Texas Instruments (TI) TPA6139A2 DirectPath™ stereo
headphone amplifier evaluation module (EVM). It includes a brief description of the module and a list of
EVM specifications.
Contents
1
2
3
Description ................................................................................................................... 2
EVM Specifications ......................................................................................................... 2
Operation ..................................................................................................................... 2
3.1
Quick-Start List for Stand-Alone Operation ..................................................................... 2
4
5
Reference .................................................................................................................... 3
4.1
4.2
TPA6139A2EVM Schematic ...................................................................................... 4
TPA6139A2EVM PCB Layers .................................................................................... 5
TPA6139A2EVM Bill of Materials ......................................................................................... 6
List of Figures
1
2
3
4
5
TPA6139A2 EVM Top View ...............................................................................................
TPA6139A2 EVM Bottom View ...........................................................................................
TPA6139A2EVM Schematic...............................................................................................
Top Silkscreen...............................................................................................................
Bottom Silkscreen...........................................................................................................
List of Tables
1
2
EVM Specifications .........................................................................................................
TPA6139A2EVM Bill of Materials.........................................................................................
Figure 1. TPA6139A2 EVM Top View
1
SLOU308–January 2011
TPA6139A2 EVM
© 2011, Texas Instruments Incorporated
Reference
3.1.2.2
Shutdown Controls
1. Shutdown is controlled by pushbutton S1. Press and hold S1 to place the TPA6139A2 in shutdown.
Release S1 to reactivate the TPA6139A2.
3.1.3
3.1.4
4
Gain Setting
The gain setting is programmed with the GAIN pin and is latched when the MUTE pin is set high. The
default gain of the TPA6139A2EVM is set to 3.5dB using a 49.9 kΩ resistor (R2). The gain resistor can be
adjusted to achieve a gain range from 0 dB to 20 dB. Refer to the datasheet for more details on gain
settings.
Power Up
Verify the correct voltage setting of the power supply and turn ON the power supply. Proper operation
of the EVM should begin.
2. Adjust the audio signal source as needed.
Reference
This section includes the EVM schematic and board layout reference.
3
SLOU308–January 2011
TPA6139A2 EVM
© 2011, Texas Instruments Incorporated
TPA6139A2EVM Bill of Materials
5
TPA6139A2EVM Bill of Materials
Table 2. TPA6139A2EVM Bill of Materials
SMD
Size
Qty. Reference
Description
Manufacturer
Part Number
1
1
2
U1
Headphone AMP with 2 Vrms output TSSOP14-PW ROHS
LED, GREEN 2.0V SMD0805 ROHS
0603
0805
0603
TPA6139A2PW
LUMEX OPTO
LITTLEFUSE
LED1
SML-LXT0805GW-TR
SMAJ100A
TVS1, TVS2
TRANSIENT VOLTAGE SUPPRESSION SMA 100V 400W
ROHS
2
1
5
1
2
1
1
C7, C9
C8
CAP SMD0603 CERM 33PFD 50V 5% NPO ROHS
CAP SMD0603 CERM 100PFD 50V 5% NPO ROHS
CAP SMD0603 CERM 1.0UFD 10V 10% X5R ROHS
CAP SMD0805 CERM 10UFD 16V 10% X5R ROHS
RESISTOR SMD0603 ZERO OHMS 1/10W ROHS
RESISTOR SMD0603 330 OHMS 5% 1/10W ROHS
0603
0603
0603
0603
0603
0603
0805
MURATA
MURATA
MURATA
MURATA
GRM1885C1H330JA01D
GRM1885C1H101JA01D
GRM185R61A105KE36D
GRM21BR61C106KE15L
C1–C5
C6
R4, R6
R1
STACKPOLE ELECTRONICS RMCF0603ZT0R00
PANASONIC
VISHAY
ERJ-3GEYJ331V
R2
RESISTOR SMD0805 49.9K OHMS 1% 1/8W THICK FILM
ROHS
CRCW080549K9FKEA
3
R3, R8, R9
RESISTOR SMD0603 100K OHM 1% THICK FILM 1/10W
ROHS
0603
PANASONIC
ERJ-3EKF1003
1
1
1
1
J1
HEADER MALE 2PIN 100LS W/ FRICTION LOCK ROHS
JACK, RCA 3-PIN PCB-RA BLACK ROHS
JACK, RCA 3-PIN PCB-RA RED ROHS
MOLEX
22-23-2021
LIN
SWITCHCRAFT
SWITCHCRAFT
KYCON
PJRAN1X1U01X
PJRAN1X1U03X
STX-3150-5N-577C
RIN
HPOUT
JACK MINI STEREO 3.5mm LIME GREEN W/SHUNTS
ROHS
1
S1
SWITCH, MOM, 160G SMT 4X3MM ROHS
E-SWITCH
TL1015AF160QG
Components not assembled: C7, C9, R2, R5, R7, TVS1, and TVS2.
6
TPA6139A2 EVM
SLOU308–January 2011
© 2011, Texas Instruments Incorporated
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the
product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are
not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations,
including product safety and environmental measures typically found in end products that incorporate such semiconductor
components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding
electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the
technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30
days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY
SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all
claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to
take any and all appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER
FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of
patents or services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI’s
environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION
PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and
can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15
of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this
equipment in other environments may cause interference with radio communications, in which case the user at his own expense
will be required to take whatever measures may be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of 3.0 V to 3.6 V and the output voltage range of 3.0 V to 3.6 V .
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are
questions concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the
EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load
specification, please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than 60°C. The EVM is designed to
operate properly with certain components above 40°C as long as the input and output ranges are maintained. These components
include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of
devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near
these devices during operation, please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
Clocks and Timers
Interface
Medical
Security
Logic
Power Mgmt
Transportation and
Automotive
Microcontrollers
RFID
Video and Imaging
Wireless
TI E2E Community Home Page
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
|