Tascam Microphone TM STPRO User Manual

TM-STPRO  
XY Stereo Microphone  
Powering the microphone  
Description  
ere are two ways to power the TM-STPRO:  
TASCAM’s TM-STPRO is a stereo X/Y microphone  
perfectly suited to capture detailed studio and live  
performances. is back-electret condenser micro-  
phone captures a wide stereo image with rich sound  
quality. e balanced XLR output is perfect for con-  
necting to TASCAM recorders like the US-144, DP-02  
and 2488neo. A switchable low cut filter is provided to  
remove low frequency rumble during recording. e  
TM-STPRO includes a 16’ stereo XLR cable for flexible  
microphone placement. Also included are a microphone  
stand clip, wind screen, AA battery and protective carry  
pouch.  
1.  
Turn on the Phantom Power switch on your micro-  
phone preamp. You should switch on phantom power for both  
channels of the TM-STPRO. Phantom power sends 48 volts  
to the microphone over the cable and is commonly found on  
professional mixers and recorders.  
2.  
Install a AA battery to power the microphone. An  
alkaline AA battery provides approximately 400 hours of op-  
eration under normal circumstances. ere is no power switch  
on the TM-STPRO, so you need to remove the battery when  
you are finished using the microphone.  
Installing the battery  
1.  
2.  
3.  
Unscrew microphone body cover  
Remove the body shell  
Insert the battery, taking note of the polarity  
e great-sounding TM-STPRO makes stereo recording  
easy and affordable for anyone.  
Specications  
Battery Precautions:  
Model:  
TM-ST PRO  
Insert the battery correctly  
Elements:  
Back Electret Condenser  
X/Y Stereo  
Do not charge the included AA battery  
Remove the battery if the microphone will not  
be used for a long period of time  
Type:  
Frequency Response:  
Sensitivity @ 1Pa:  
Impedance:  
Maximum SPL:  
Dynamic Range:  
Power:  
30 Hz - 20k Hz  
-47 dBV  
If the battery leaks, clean the battery holder  
before inserting a new battery  
200Ω, BALANCED  
126 dB SPL  
102 dB  
Using the Low Cut Filter  
Phantom Power or AA Battery  
2 mA  
e low-cut filter switch is located on the top of the micro-  
phone. To switch on the low cut filter, move the switch to the  
down position (indicated by the  
to the up position for full bass response (indicated by the  
icon). e low cut filter attenuates frequencies below 150Hz at  
a cutoff slope of 6dB per octave.  
Consumption:  
Connector:  
Weight:  
Integral 5-pin XLR-M  
320g/11.3 oz.  
icon). Move the switch  
To permanently set the microphone for flat response, so that  
it cannot be accidentally switched to rolloff mode, use the  
switch protector located under the switch. Unscrew the philips  
screw holding the switch protector in place, rotate it so it faces  
upward, then replace the philips screw.  
Included Accessories:  
16’ Stereo XLR5-F to dual XLR3-M cable  
Microphone Stand Clip  
AA Battery  
Windscreen  
Protective Pouch  
 

Texas Instruments Laptop 3000 WinSX User Manual
Thermador Dishwasher P24 User Manual
Tyco Digital Camera 8200 2646 00 B0 User Manual
Uniden Cordless Telephone EXP90 User Manual
Uniden Lawn Mower Accessory GH 130 User Manual
Universal Remote Control Universal Remote UR5U BH8000 User Manual
Venturer Karaoke Machine CDG 62 User Manual
Vermont Casting Smoker 2505G User Manual
Viking Refrigerator DDRB364 User Manual
Vizio Speaker System SB4020M A0 User Manual